INSTALLATION INSTRUCTIONS LFH160 Cable
|
|
|
- Cori Willis
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS LFH160 This guide describes how to connect and use the National Instruments LFH160 cable which has a maximum voltage rating of 100 VDC, CAT I. Use the LFH160 cable to connect the NI PXI-2576 switch module to your application. As illustrated in Figure 1, one end of the LFH160 cable connects to the NI PXI-2576, and the other end of the cable terminates with four 50-pin female D-SUB connectors. 2 3 NATIONAL INSTRUMENTS 4 1 NATIONAL INSTRUMENTS NATIONAL INSTRUMENTS NATIONAL INSTRUMENTS NATIONAL INSTRUMENTS 1 LFH160 Connector 2 Leg Label 3 50-Pin Female D-SUB Connectors 4 Thumbscrews Figure 1. LFH160
2 Contents What You Need to Get Started... 2 Getting Started with the LFH Configuration... 3 Specifications Environment Accessories Where to Go for Support What You Need to Get Started To use the LFH160 cable, you need the following items: LFH160 cable NI PXI-2576 switch module and documentation #1 Phillips screwdriver Getting Started with the LFH160 Complete the following steps to connect the LFH160 cable to the NI PXI-2576 and your application. 1. Connect the LFH160 connector to the NI PXI-2576 connector on the switch module as shown in Figure NATIONAL INSTRUMENTS 1 LFH160 Connector 2 Chassis Screws 3 NI PXI-2576 Connector Figure 2. Connecting the LFH160 to the NI PXI Tighten the chassis screws on the LFH160 cable. 3. Connect the D-SUB connectors on the LFH160 cable to your application. Refer to Tables 1 through 4 in the Configuration section to determine how to connect signals to your application. LFH160 Installation Instructions 2 ni.com
3 Configuration The LFH160 connector and the four 50-pin female D-SUB connectors, on the LFH160 cable provide connection to the NI PXI-2576 and your application, respectively. Figures 3 and 4 show the pinouts for both connectors. Use the pinouts and the pin assignments listed in Tables 1 through 4 to determine how to connect signals to your application. Refer to the NI Switches Help for a complete listing of channel names and pinouts. Pin 120 Pin 121 Pin 41 Pin 40 Pin 160 Pin 81 Pin 1 Pin 80 Figure 3. LFH160 Connector Pin 1 Pin 18 Pin 34 Pin 17 Pin 50 Pin 33 Figure Pin Female D-SUB Connector National Instruments Corporation 3 LFH160 Installation Instructions
4 Table 1. Pin Assignment for LFH160 Backshell 1 50-Pin D-SUB Backshell 1 COM0 159 P1.20 COM P1.19 CH0 157 P1.2 CH P1.1 CH1 155 P1.4 CH P1.3 CH2 153 P1.35 CH P1.34 CH3 151 P1.37 CH P1.36 COM1 82 P1.24 COM1+ 81 P1.23 CH4 84 P1.6 CH4+ 83 P1.5 CH5 86 P1.8 CH5+ 85 P1.7 CH6 88 P1.39 CH6+ 87 P1.38 CH7 90 P1.41 CH7+ 89 P1.40 Shield_GND1 161 P1 shell COM2 79 P1.28 COM2+ 80 P1.27 CH8 77 P1.10 CH8+ 78 P1.9 CH9 75 P1.12 CH9+ 76 P1.11 CH10 73 P1.43 CH P1.42 CH11 71 P1.45 CH P1.44 LFH160 Installation Instructions 4 ni.com
5 Table 1. Pin Assignment for LFH160 Backshell 1 (Continued) 50-Pin D-SUB Backshell 1 COM3 2 P1.32 COM3+ 1 P1.31 CH12 4 P1.14 CH12+ 3 P1.13 CH13 6 P1.16 CH13+ 5 P1.15 CH14 8 P1.47 CH14+ 7 P1.46 CH15 10 P1.49 CH15+ 9 P1.48 Shield_GND2 161 P1 shell No Connect P1.17 No Connect P1.18 No Connect P1.21 No Connect P1.22 No Connect P1.25 No Connect P1.26 No Connect P1.29 No Connect P1.30 No Connect P1.33 No Connect P1.50 National Instruments Corporation 5 LFH160 Installation Instructions
6 Table 2. Pin Assignment for LFH160 Backshell 2 50-Pin D-SUB Backshell 2 COM4 149 P2.20 COM P2.19 CH P2.2 CH P2.1 CH P2.4 CH P2.3 CH P2.35 CH P2.34 CH P2.37 CH P2.36 COM5 92 P2.24 COM5+ 91 P2.23 CH20 94 P2.6 CH P2.5 CH21 96 P2.8 CH P2.7 CH22 98 P2.39 CH P2.38 CH P2.41 CH P2.40 Shield_GND3 161 P2 shell COM6 69 P2.28 COM6+ 70 P2.27 CH24 67 P2.10 CH P2.9 CH25 65 P2.12 CH P2.11 CH26 63 P2.43 CH P2.42 CH27 61 P2.45 CH P2.44 LFH160 Installation Instructions 6 ni.com
7 Table 2. Pin Assignment for LFH160 Backshell 2 (Continued) 50-Pin D-SUB Backshell 2 COM7 12 P2.32 COM7+ 11 P2.31 CH28 14 P2.14 CH P2.13 CH29 16 P2.16 CH P2.15 CH30 18 P2.47 CH P2.46 CH31 20 P2.49 CH P2.48 Shield_GND4 161 P2 shell No Connect P2.17 No Connect P2.18 No Connect P2.21 No Connect P2.22 No Connect P2.25 No Connect P2.26 No Connect P2.29 No Connect P2.30 No Connect P2.33 No Connect P2.50 National Instruments Corporation 7 LFH160 Installation Instructions
8 Table 3. Pin Assignment for LFH160 Backshell 3 50-Pin D-SUB Backshell 3 COM8 139 P3.20 COM P3.19 CH P3.2 CH P3.1 CH P3.4 CH P3.3 CH P3.35 CH P3.34 CH P3.37 CH P3.36 COM9 102 P3.24 COM P3.23 CH P3.6 CH P3.5 CH P3.8 CH P3.7 CH P3.39 CH P3.38 CH P3.41 CH P3.40 Shield_GND5 162 P3 shell COM10 59 P3.28 COM P3.27 CH40 57 P3.10 CH P3.9 CH41 55 P3.12 CH P3.11 CH42 53 P3.43 CH P3.42 CH43 51 P3.45 CH P3.44 LFH160 Installation Instructions 8 ni.com
9 Table 3. Pin Assignment for LFH160 Backshell 3 (Continued) 50-Pin D-SUB Backshell 3 COM11 22 P3.32 COM P3.31 CH44 24 P3.14 CH P3.13 CH45 26 P3.16 CH P3.15 CH46 28 P3.47 CH P3.46 CH47 30 P3.49 CH P3.48 Shield_GND6 162 P3 shell No Connect P3.17 No Connect P3.18 No Connect P3.21 No Connect P3.22 No Connect P3.25 No Connect P3.26 No Connect P3.29 No Connect P3.30 No Connect P3.33 No Connect P3.50 National Instruments Corporation 9 LFH160 Installation Instructions
10 Table 4. Pin Assignment for LFH160 Backshell 4 50-Pin D-SUB Backshell 4 COM P4.20 COM P4.19 CH P4.2 CH P4.1 CH P4.4 CH P4.3 CH P4.35 CH P4.34 CH P4.37 CH P4.36 COM P4.24 COM P4.23 CH P4.6 CH P4.5 CH P4.8 CH P4.7 CH P4.39 CH P4.38 CH P4.41 CH P4.40 Shield_GND7 162 P4 shell COM14 49 P4.28 COM P4.27 CH56 47 P4.10 CH P4.9 CH57 45 P4.12 CH P4.11 CH58 43 P4.43 CH P4.42 CH59 41 P4.45 CH P4.44 LFH160 Installation Instructions 10 ni.com
11 Table 4. Pin Assignment for LFH160 Backshell 4 (Continued) 50-Pin D-SUB Backshell 4 Specifications COM15 32 P4.32 COM P4.31 CH60 34 P4.14 CH P4.13 CH61 36 P4.16 CH P4.15 CH62 38 P4.47 CH P4.46 CH63 40 P4.49 CH P4.48 Shield_GND8 162 P4 shell No Connect P4.17 No Connect P4.18 No Connect P4.21 No Connect P4.22 No Connect P4.25 No Connect P4.26 No Connect P4.29 No Connect P4.30 No Connect P4.33 No Connect P4.50 Maximum voltage VDC, CAT I, 1 A Caution Do not connect to MAINs supply circuits (e.g., wall outlets) of 115 or 230 VAC. Refer to the Read Me First: Safety and Radio-Frequency Interference document for more information about Measurement Categories. Weight g (38.4 oz) National Instruments Corporation 11 LFH160 Installation Instructions
12 Environment Accessories Operating temperature...0 C to 55 C Storage temperature C to 70 C Relative humidity...5% to 85%, noncondensing Pollution Degree...2 Maximum altitude...2,000 m Indoor use only. Visit ni.com for information about the following accessory. Table 5. NI Accessory for the LFH160 Accessory Part Number TBX-50 terminal block, with screw connection and 50 position D-Subminiature pin strip Caution You must install mating connectors according to local safety codes and standards and according to the specifications provided by the connector manufacturer. You are responsible for verifying safety compliance of third-party connectors and their usage according to the relevant standard(s), including UL and CSA in North America and IEC and VDE in Europe. Refer to Table 6 for information about third-party accessories for the LFH160. Table 6. Third-Party Accessories for the LFH160 Accessory Manufacturer Part Number VARIOFACE module, with screw connection and 50 position D-Subminiature pin strip VARIOFACE module, with screw connection and 50 position D-Subminiature pin strip VARIOFACE module, with screw connection and 50 position D-Subminiature pin strip, with LED indicators Phoenix Contact Phoenix Contact Phoenix Contact FLKM-D50 SUB/S FLKMS-D50 SUB/S FLKM-D50 SUB/S/LA Right-angle 50 position male D-SUB connector * Amp * Small quantity orders are available from Digi-Key Corporation (part number A23398-ND). LFH160 Installation Instructions 12 ni.com
13 Where to Go for Support The National Instruments Web site is your complete resource for technical support. At ni.com/ support you have access to everything from troubleshooting and application development self-help resources to and phone assistance from NI Application Engineers. National Instruments corporate headquarters is located at North Mopac Expressway, Austin, Texas, National Instruments also has offices located around the world to help address your support needs. For telephone support in the United States, create your service request at ni.com/support and follow the calling instructions or dial For telephone support outside the United States, contact your local branch office: Australia , Austria , Belgium 32 (0) , Brazil , Canada , China , Czech Republic , Denmark , Finland 358 (0) , France , Germany , India , Israel , Italy , Japan , Korea , Lebanon 961 (0) , Malaysia , Mexico , Netherlands 31 (0) , New Zealand , Norway 47 (0) , Poland , Portugal , Russia , Singapore , Slovenia , South Africa , Spain , Sweden 46 (0) , Switzerland , Taiwan , Thailand , Turkey , United Kingdom 44 (0) National Instruments Corporation 13 LFH160 Installation Instructions
14 National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your CD, or ni.com/patents National Instruments Corporation. All rights reserved B Dec07
NI CB-37F-LP. Introduction INSTALLATION GUIDE. Connector Block for 37-Pin D-Sub Devices
INSTALLATION GUIDE NI CB-7F-LP Connector Block for 7-Pin D-Sub Devices Introduction This installation guide describes how to install and connect signals to the NI CB-7F-LP connector block for use with
You need the following to set up and use your terminal block:
INSTALLATION GUIDE NI TB-2706 PXI/PXIe Terminal Block for M Series and NI 6143 Devices Contents Introduction This installation guide describes how to install and connect signals to the NI TB-2706 terminal
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9870E
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9870E 4-Port, RS232 Serial Module This document describes how to use the National Instruments 9870E and includes dimensions, pin assignments, and specifications
NI 6521 Specifications
NI 6521 Specifications This document lists specifications for the NI 6521 device. All specifications are subject to change without notice. These specifications are typical at 25 C unless otherwise noted.
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9871E
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9871E 4-Port, RS485/RS422 Serial Module This document describes how to use the National Instruments 9871E and includes dimensions, pin assignments, and specifications
OPERATING INSTRUCTIONS AND SPECIFICATIONS. NI 9208E 16-Channel, ±20 ma, 24-Bit Analog Input Module
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9208E 16-Channel, ±20 ma, 24-Bit Analog Input Module This document describes how to use the National Instruments 9208E and includes dimensions, pin assignments,
NI 653x Cable Adapter
USER GUIDE NI 65x Cable Adapter Contents The NI 65x cable adapter interfaces with National Instruments high-speed digital I/O (DIO) devices. The cable adapter provides an easy way to connect the Very High
LabVIEW DSP Module. Contents. Introduction RELEASE NOTES. Version 1.0
RELEASE NOTES LabVIEW DSP Module Version 1.0 Contents Introduction Introduction... 1 LabVIEW Embedded Edition... 2 System Requirements... 3 Installation... 3 DSP Module Documentation... 4 Where to Go for
NI SMB-2145/2146/2147/2148
USER GUIDE NI SMB-2145/2146/2147/2148 Shielded Signal Accessories for NI 5751/5752 Adapter Modules The NI SMB-2145/2146/2147/2148 (NI SMB-214x) devices are shielded signal accessories for NI FlexRIO digitizer
NI SD Card Memory Module
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9802 2 SD Card Memory Module Français Deutsch ni.com/manuals This document describes how to use the National Instruments 9802 and includes specifications for
Calibrating FieldPoint Analog Input Modules with Calibration Executive
USER GUIDE Calibrating FieldPoint Analog Input Modules with Calibration Executive Contents This document contains step-by-step instructions for loading and running National Instruments Calibration Executive
FieldPoint. FP-1000/1001 FieldPoint Quick Start Guide. Install the Network Module Mount the module on a DIN rail. What You Need to Get Set Up
TM FieldPoint FP-1000/1001 FieldPoint Quick Start Guide What You Need to Get Set Up Network module 35 mm DIN rail Two DIN rail locks (included) Terminal base(s) I/O module(s) 11 30 VDC power supply Accessories:
cfp-rly-421 Features Installing the cfp-rly-421 FieldPoint Operating Instructions Eight-Channel SPST Relay Module
FieldPoint Operating Instructions cfp-rly-421 Eight-Channel SPST Relay Module These operating instructions describe how to install and use the National Instruments cfp-rly-421 relay module, revision 185151C-01
FP-PS-4. Features. Installation
OPERATING INSTRUCTIONS FP-PS-4 FieldPoint Power Supply These operating instructions describe the installation, features, and characteristics of the FP-PS-4. Features The FP-PS-4 is a FieldPoint power supply
Getting Started with R Series Intelligent DAQ
Getting Started with R Series Intelligent DAQ This document explains how to install and configure National Instruments PCI/PXI-781xR, PCI/PXI-783xR, PXI-784xR, and PXI-785xR (NI 78xxR) devices. This document
FieldPoint cfp-20xx. Quick Start Guide. What You Need to Get Set Up
Quick Start Guide FieldPoint cfp-20xx What You Need to Get Set Up cfp-20xx LabVIEW RT controller Mounting hardware (DIN rail, panel-mount, or rack-mount accessory) I/O module(s) cfp-bp-x backplane, connector
Getting Results with the NI PXI-6585R
Getting Results with the NI PXI-6585R This document explains how to install and configure the National Instruments PXI-6585R, comprised of an NI FlexRIO FPGA module (NI PXI-79xxR) and an NI 6585 FlexRIO
Caution Electrostatic discharge can damage your controller. To avoid such damage, handle the controller only in a proper ESD-controlled environment.
INSTALLATION GUIDE NI VXIpc -882 This guide contains information about installing and troubleshooting your NI VXIpc-882 controller and components. This guide refers to the NI VXIpc-882 User Manual, which
Getting Started with R Series Multifunction RIO
Getting Started with R Series Multifunction RIO This document explains how to install and configure National Instruments PCI/PXI-781xR, PCI/PXI-783xR, PCIe/PXI-784xR, and PCIe/PXI-785xR, referred to collectively
Getting Started with NI-Motion for NI 73xx Motion Controllers
Getting Started with NI-Motion for NI 73xx Motion Controllers This document provides instructions for installing and getting started with the NI-Motion driver software and National Instruments PXI/PCI-73xx
NI USB Introduction USER GUIDE AND SPECIFICATIONS. 4-Channel, ±10 V, 16-Bit Analog Voltage Output Module
USER GUIDE AND SPECIFICATIONS NI USB-9263 4-Channel, ±10 V, 16-Bit Analog Voltage Output Module Introduction This user guide describes how to use the National Instruments USB-9263 and lists the device
Getting Started with the NI 8234
Getting Started with the NI 8234 The NI 8234 is a Gigabit Ethernet (GigE) interface device for PXI Express (PXIe) or CompactPCI Express (cpcie). This document describes how to install the necessary hardware
LabVIEW DSP Module Release and Upgrade Notes
LabVIEW DSP Module Release and Upgrade Notes Version 2.5 Contents Introduction... 2 System Requirements... 2 Installation... 3 Installing the Drivers... 3 Setting Up the Hardware... 3 Installing Third-Party
NI 9213 Calibration Procedure
NI 9213 Calibration Procedure Français Deutsch ni.com/manuals This document contains information about calibrating National Instruments 9213 modules using NI-DAQmx. This calibration procedure is intended
INSTALLATION INSTRUCTIONS SH160F-160M-NI SwitchBlock Cable
INSTALLATION INSTRUCTIONS SH160F-160M-NI SwitchBlock Cable This guide describes how to connect and use the National Instruments SH160F-160M-NI SwitchBlock shielded cable which has a maximum voltage rating
NI Channel, 0 20 ma, 16-Bit Analog Current Output Module
OPERATING INSTRUCTIONS AND SPECIFICATIONS NI 9265 4-Channel, 0 20 ma, 16-Bit Analog Current Output Module Français Deutsch ni.com/manuals This document describes how to use the National Instruments 9265
SH Cable Specifications
SH96-96-1 Cable Specifications This document lists specifications for the SH96-96-1 shielded cable. These specifications are typical for the range of 0 C to 55 C unless otherwise stated. The system must
Compact FieldPoint cfp-cal
Quick Start Guide Compact FieldPoint cfp-cal How to Use This Document This document describes the installation procedure for the cfp-cal, a Compact FieldPoint network interface designed for calibrating
TBX-96 TERMINAL BLOCK
INSTALLATION GUIDE TBX-96 TERMINAL BLOCK This guide describes how to install and use the TBX-96 terminal block with the SCXI-1100, SCXI-1102B/C, SCXI-1104/C, and SCXI-1581 modules. The TBX-96 is a shielded,
Getting Results with the NI 5752R
Getting Results with the NI 5752R This document explains how to install and configure an NI FlexRIO FPGA module (NI PXI/PXIe-79xxR) and an NI FlexRIO adapter module (NI 5752) to form the NI 5752R. This
Electrical. SPECIFICATIONS SH Cable
SPECIFICATIONS SH96-96-1 Cable When this symbol is marked on a product, it denotes a warning advising you to take precautions to avoid electrical shock. This icon denotes a caution, which advises you of
VME-GPIB Installation and User Guide
VME-GPIB Installation and User Guide Contents Introduction Introduction... 1 What Your Kit Should Contain... 2 Optional Equipment and Software Packages... 3 Unpacking your VME-GPIB... 3 Functional Overview...
FP-AO-210 AND CFP-AO-210
FieldPoint Operating Instructions FP-AO-210 AND CFP-AO-210 Eight-Channel 10 V Analog Output Module These operating instructions describe how to install and use the National Instruments FP-AO-210 and cfp-ao-210
NI CAN Demo Box. NI CAN Demo Box User Guide. Power supply (+9 VDC to +12 VDC) 68-pin Multifunction Data Acquisition board
USER GUIDE NI CAN Demo Box Introduction This document discusses the NI CAN Demo Box architecture and use and provides examples for software. The NI CAN Demo Box, when communicating with National Instruments
NI USB Introduction USER GUIDE AND SPECIFICATIONS. 8-Channel, 24 V Logic, Sinking Digital Input Device
USER GUIDE AND SPECIFICATIONS NI USB-9421 8-Channel, 24 V Logic, Sinking Digital Input Device Introduction This user guide describes how to use the National Instruments USB-9421 and lists the device specifications.
NI SPEEDY-33. '7 NATIONAL INSTALLATIONGUIDE. P~ClCl J ~ Ig~~!1 "INSTRUMENTSN. 1~~~~~~g~~lm.OOOQ{JOOO,
INSTALLATIONGUIDE NI SPEEDY-33 P~ClCl J ~ This installation guide describes how to install and configure the NI SPEEDY-33DSP device for use with a Pc. Figure] depicts the NI SPEEDY-33. 0 ~~.O~~ ~ Ig~~!1
Getting Started with the NI PXI/PCIe-8231
Getting Started with the NI PXI/PCIe-8231 The NI PXI/PCIe-8231 (NI 8231) is a Gigabit Ethernet (GigE) interface device for the PXI, PCI Express (PCIe), or CompactPCI bus. This document describes how to
QUICK START GUIDE. What You Need to Get Set Up
QUICK START GUIDE FieldPoint What You Need to Get Set Up FP-20xx LabVIEW RT controller 35 mm DIN rail Two DIN rail locks (included) Terminal base(s) I/O module(s) 11 30 VDC power supply FP-20xx Accessories:
Getting Started with the NI 8234
Getting Started with the NI 8234 The NI 8234 is a Gigabit Ethernet (GigE) interface device for PXI Express (PXIe) or CompactPCI Express (cpcie). This document describes how to install and configure the
FP-AO-200 AND CFP-AO-200
FieldPoint Operating Instructions FP-AO-200 AND CFP-AO-200 Eight-Channel 20 ma Loop Output Modules These operating instructions describe how to install and use the National Instruments FP-AO-200 and cfp-ao-200
USER GUIDE Universal Motion Interface (UMI)-7764
USER GUIDE Universal Motion Interface (UMI)-7764 Contents Introduction This document provides information about the National Instruments Universal Motion Interface (UMI)-7764 functionality and includes
NI CardBus-8310-to-PXI Expansion Kit
INSTALLATION GUIDE NI CardBus-8310-to-PXI Expansion Kit Before Installation This document provides instructions on the installation of the NI CardBus-8310-to-PXI Expansion Kit. Before installing the NI
NI 6584R User Guide and Specifications
NI 6584R User Guide and Specifications Contents The NI 6584 is an RS-485/422 adapter module designed to work in conjunction with your NI FlexRIO FPGA module. This document contains signal information and
Sample. LabWindows TM /CVI TM Core 1 Exercises Manual
LabWindows TM /CVI TM Core 1 Exercises Manual Course Software Version 2010 January 2011 Edition Part Number 325669A-01 LabWindows/CVI Core 1 Course Manual Copyright 1994 2011 National Instruments Corporation.
SCXI HIGH-VOLTAGE 8 4 MATRIX TERMINAL BLOCK
INSTALLATION GUIDE SCXI -1332 HIGH-VOLTAGE 8 4 MATRIX TERMINAL BLOCK Introduction This guide describes how to install and use the SCXI-1332 terminal block with your SCXI-1127 module. The SCXI-1332 terminal
Getting Started with the NI PCIe-8253
Getting Started with the NI PCIe-8253 The NI PCIe-8253 (NI 8253) is an IEEE 1394a 1 and IEEE 1394b interface device for PCI Express (PCIe). This document describes how to install and configure the necessary
For NI PXI and NI SCXI Switch Modules
GETTING STARTED GUIDE NI Switches For NI PXI and NI SCXI Switch Modules This document explains how to install, configure, and test a National Instruments PXI or SCXI switch module. This document contains
Getting Started with the NI PCIe-8235
Getting Started with the NI PCIe-8235 The NI PCIe-8235 (NI 8235) is a quad port Gigabit Ethernet (GigE) interface device for PCI Express (PCIe) computers. This document describes how to install and configure
NI USB Introduction USER GUIDE AND SPECIFICATIONS. 8-Channel, 24 V Logic, Sourcing Digital Output Device
USER GUIDE AND SPECIFICATIONS NI USB-9472 8-Channel, 24 V Logic, Sourcing Digital Output Device Introduction This user guide describes how to use the National Instruments NI USB-9472 and lists the device
Getting Started with the NI PCIe-8255R
Getting Started with the NI PCIe-855R The NI PCIe-855R (NI 855R) is an IEEE 1394a 1 and IEEE 1394b interface device with reconfigurable I/O (RIO) for PCI Express (PCIe). This document describes how to
Getting Started with the NI PCI-1405
Getting Started with the NI PCI-1405 The NI PCI-1405 (NI 1405) is a PCI monochrome and color image acquisition device that supports a diverse range of analog cameras. This document describes how to install
Power Analyzer Firmware Update Utility Version Software Release Notes
Power Analyzer Firmware Update Utility Version 3.1.0 Software Release Notes Contents General Information... 2... 2 Supported models... 2 Minimum system requirements... 2 Installation instructions... 2
CompactRIO Reconfigurable Embedded Chassis
INSTALLATION INSTRUCTIONS CompactRIO Reconfigurable Embedded Chassis crio-9111/9112/9113/9114/9116 2 4 1 1 3 3 1 Controller 2 Eight-Slot Reconfigurable Embedded Chassis (crio-9112/9114/9116) 3 C Series
Getting Started with the NI PCI-8254R
Getting Started with the NI PCI-854R The NI PCI-854R (NI 854R) is an IEEE 394a interface device for PCI with reconfigurable I/O (RIO). This document describes how to install and configure the necessary
NI USB Introduction USER GUIDE AND SPECIFICATIONS. 4-Channel, 0 20 ma, 16-Bit Analog Current Output Module
USER GUIDE AND SPECIFICATIONS NI USB-9265 4-Channel, 0 20 ma, 16-Bit Analog Current Output Module Introduction This user guide describes how to use the National Instruments USB-9265 and lists the device
FP-2000/2010 FieldPoint Quick Start Guide
FP-2000/2010 FieldPoint Quick Start Guide What You Need to Get Set Up 1 Network Module Mounting Hardware (DIN rail or panel mount accessory) Terminal Base(s) I/O Module(s) Power Supply Accessories: Ethernet
Sample. LabWindows TM /CVI TM Core 1 Course Manual
LabWindows TM /CVI TM Core 1 Course Manual Course Software Version 2010 January 2011 Edition Part Number 325668A-01 LabWindows/CVI Core 1 Course Manual Copyright 1994 2011 National Instruments Corporation.
Getting Started with the NI PCIe-1433
Getting Started with the NI PCIe-1433 The NI PCIe-1433 (NI 1433) is a PCI Express (PCIe) image acquisition device that supports Base, Medium, Full, and Extended Full configuration Camera Link-compatible
NI PCIe-8255R Quick Start Guide
NI PCIe-8255R Quick Start Guide The NI PCIe-8255R is an IEEE 394a and IEEE 394b interface device for PCI Express (PCIe) with reconfigurable I/O (RIO). This document explains how to install and configure
Compact FieldPoint cfp-1808
Quick Start Guide Compact FieldPoint cfp-1808 What You Need to Get Set Up cfp-1808 Network Interface Mounting hardware (DIN rail, panel-mount, or rack-mount accessory) I/O module(s) Connector blocks and/or
FP-AIO-600 and cfp-aio-600
FieldPoint Operating Instructions FP-AIO-600 and cfp-aio-600 Four-Channel Analog Input, Four-Channel Analog Output, 12-Bit Module These operating instructions describe how to install and use the National
Sample. LabVIEW TM Core 1 Exercises. Course Software Version 2010 August 2010 Edition Part Number B-01. LabVIEW Core 1 Exercises
LabVIEW TM Core 1 Exercises Course Software Version 2010 August 2010 Edition Part Number 325291B-01 LabVIEW Core 1 Exercises Copyright 1993 2010 National Instruments Corporation. All rights reserved. Under
NI USB-9201/9221. Introduction USER GUIDE AND SPECIFICATIONS. 8-Channel, 12-Bit Analog Input Devices
USER GUIDE AND SPECIFICATIONS NI USB-9201/9221 8-Channel, 12-Bit Analog Input Devices Introduction This user guide describes how to use the National Instruments NI USB-9201/9221 devices and lists the specifications.
Instructions. (For 6180 Industrial Computers) Applications. Overview & Safety
Instructions (For 6180 Industrial Computers) Applications This instruction sheet describes how to replace the following displays and backlights for 6180 Industrial Computers. All display kits contain a
GETTING STARTED GUIDE NI Channel, 50 Arms Continuous, 24-Bit, Analog Input Module
GETTING STARTED GUIDE NI 9247 3-Channel, 50 Arms Continuous, 24-Bit, Analog Input Module This document explains how to connect to the NI 9247. Note Before you begin, complete the software and hardware
Getting Started with the NI PXI/PCI-1422
Getting Started with the NI PXI/PCI-1422 The NI PXI/PCI-1422 (NI 1422) is an image acquisition device for PXI, PCI, or CompactPCI. This document describes how to install and configure the necessary hardware
Safety. Introduction
KickStart Guide Safety Introduction Safety precautions Before using this product, see the safety precautions associated with your instrument. The instrumentation associated with this software is intended
CB-27T, TBX-68T, AND CB-68T ISOTHERMAL TERMINAL BLOCKS INSTALLATION GUIDE
CB-7T, TBX-8T, AND CB-8T ISOTHERMAL TERMINAL BLOCKS INSTALLATION GUIDE This installation guide describes how to install and connect signals to the CB-7T, TBX-8T, and CB-8T isothermal terminal blocks for
FieldPoint cfp-21xx. Quick Start Guide. What You Need to Get Set Up
Quick Start Guide FieldPoint cfp-21xx What You Need to Get Set Up cfp-21xx LabVIEW RT controller Mounting hardware (DIN rail, panel-mount, or rack-mount accessory) I/O module(s) cfp-bp-x backplane, connector
This installation guide describes how to install and connect signals to the NI TBX-2808 screw terminal accessory for use with NI SwitchBlock cards.
INSTALLATION INSTRUCTIONS NI TBX-2808 Screw Terminal Accessory for the NI SwitchBlock This installation guide describes how to install and connect signals to the NI TBX-2808 screw terminal accessory for
The NI TB-2648/2649/2650/2651 terminal blocks configure your NI PXI/PXIe-2531 (NI 2531) in one of the following topologies. 1-wire 8 64 matrix
INSTALLATION INSTRUCTIONS NI TB-//0/ Terminal Blocks for the NI PXI/PXIe- Introduction The NI TB-//0/ terminal blocks configure your NI PXI/PXIe- (NI ) in one of the following topologies. Table. NI Configurations
NI PXI-2567 Specifications
NI PXI-2567 Specifications 64-Channel Relay Driver Module This document lists specifications for the NI PXI-2567 relay driver module. All specifications are subject to change without notice. Visit ni.com/manuals
IVN Safety Guidelines GETTING STARTED GUIDE. 100BASE-T1 Media Converter
#6-32 GETTING STARTED GUIDE IVN-8561 100BASE-T1 Media Converter IVN-8561 100BASE-T1 Media Converter POWER P1 P3 MASTER LINK/ACT POWER PORT 4 5V 2.8W MAX This document describes how to begin using the IVN-8561
CompactRIO NI crio-9012/9014
OPERATING INSTRUCTIONS AND SPECIFICATIONS CompactRIO NI crio-9012/9014 Intelligent Real-Time Embedded Controller for CompactRIO 1 2 8 3 4 5 6 7 1 LEDs 2 SMB Connector 3 Power Connector 4 DIP Switches 5
DATA SHEET. Catalyst Inline Power Patch Panel
DATA SHEET Inline Power Patch DEPLOYED IN THE WIRING CLOSET, THE CATALYST INLINE POWER PATCH PANEL PROVIDES FAST ETHERNET ENHANCEMENTS NEEDED FOR MULTISERVICE NETWORKING WHILE PRESERVING CUSTOMER INVESTMENTS
GETTING STARTED GUIDE NI AO, 0 ma to 20 ma, 16 Bit Simultaneous
GETTING STARTED GUIDE NI 9266 8 AO, 0 ma to 20 ma, 16 Bit Simultaneous This document explains how to connect to the NI 9266. In this document, the NI 9266 with screw terminal and the NI 9266 with DSUB
Getting Started with the NI PXI/PCI-1409
Getting Started with the NI PXI/PCI-1409 The NI PXI/PCI 1409 (NI 1409) is a high-accuracy monochrome image acquisition device for the PXI, PCI, or CompactPCI bus. This document describes how to install
CALIBRATION PROCEDURE CAL Contents. Software
CALIBRATION PROCEDURE CAL-4353 Français Deutsch ni.com/manuals Contents Software This document contains information about verifying and adjusting National Instruments NI PXIe-4353 modules using NI-DAQmx
GETTING STARTED GUIDE NI V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
GETTING STARTED GUIDE NI 9425 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module This document explains how to connect to the NI 9425. In this document, the NI 9425 with spring terminal and
Cisco CallManager 4.0-PBX Interoperability: Lucent/Avaya Definity G3 MV1.3 PBX using 6608-T1 PRI NI2 with MGCP
Application Note Cisco CallManager 4.0-PBX Interoperability: Lucent/Avaya Definity G3 MV1.3 PBX using 6608-T1 PRI NI2 with MGCP Introduction This is an application note for connectivity of Lucent/Avaya
USER GUIDE SC-2075 SIGNAL CONDITIONING ACCESSORY
USER GUIDE SC-2075 SIGNAL CONDITIONING ACCESSORY The SC-2075 is a desktop signal conditioner that you can connect directly to National Instruments E Series or 1200 Series devices. The SC-2075 has the following
ChemiDoc and ChemiDoc MP Imaging Systems with Image Lab Touch Software Installation Qualification Protocol (IQ)
ChemiDoc and ChemiDoc MP Imaging Systems with Image Lab Touch Software Protocol (IQ) Catalog #17001401 and 17001402 Table of Contents Page Section 1: General Information... 3 1.1 Scope... 3 1.2 Protocol
GETTING STARTED GUIDE NI Channel Solid-State Relay (SSR) Digital Output Module
GETTING STARTED GUIDE NI 9485 8-Channel Solid-State Relay (SSR) Digital Output Module This document explains how to connect to the NI 9485. Note Before you begin, complete the software and hardware installation
AC/DC (120V) Input Module Cat. No IAD Series C
Installation Instructions To The Installer Pre-installation Considerations Power Requirements Initial Handling This document provides information on: important pre-installation considerations power supply
4 GHz Active Probe P7240 Datasheet
4 GHz Active Probe P7240 Datasheet Applications High-speed digital systems design Component design/characterization Signal integrity, jitter, and timing analysis Mechanical engineering and test Measures
FP-1600 FieldPoint Quick Start Guide
FP-1600 FieldPoint Quick Start Guide What You Need to Get Set Up 1 Network Module Mounting Hardware (DIN rail or panel mount accessory) Terminal Base(s) I/O Module(s) Install the Network Module DIN Rail
Global entertainment and media outlook Explore the content and tools
www.pwc.com/outlook Global entertainment and media outlook Explore the content and tools A comprehensive online source of global analysis for consumer/ end-user and advertising spending 5-year forecasts
CISCO 7304 SERIES ROUTER PORT ADAPTER CARRIER CARD
DATA SHEET CISCO 7304 SERIES ROUTER PORT ADAPTER CARRIER CARD The Cisco 7304 Router, part of the industry-leading Cisco 7000 Series, is optimized to deliver flexible, high-performance IP and Multiprotocol
Cisco Aironet In-Building Wireless Solutions International Power Compliance Chart
Cisco Aironet In-Building Wireless Solutions International Power Compliance Chart ADDITIONAL INFORMATION It is important to Cisco Systems that its resellers comply with and recognize all applicable regulations
R Series for PXI Express Digital RIO with Kintex-7 325T FPGA. ni.com/manuals. This document explains how to install and configure the NI PXIe-7822R.
GETTING STARTED GUIDE NI PXIe-7822R R Series for PXI Express Digital RIO with Kintex-7 325T FPGA Français Deutsch 日本語한국어简体中文 ni.com/manuals This document explains how to install and configure the NI PXIe-7822R.
END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO MEDIA CONVERGENCE SERVER 7845H-2400
END-OF-LIFE NOTICE, NO. 2566 END-OF-SALE AND END-OF-LIFE ANNOUNCEMENT FOR THE CISCO MEDIA CONVERGENCE SERVER 7845H-2400 Cisco Systems announces the end of life of the Cisco Media Convergence Server 7845H-2400.
NI 5761R User Guide and Specifications
NI 5761R User Guide and Specifications Contents The NI 5761 is a 25 MS/s analog input adapter module designed to work in conjunction with your NI FlexRIO FPGA module. This document contains signal information
Getting Started with the NI LabVIEW Embedded Module for ADI Blackfin Processors Version 8.6
Getting Started with the NI LabVIEW Embedded Module for ADI Blackfin Processors Version 8.6 The NI LabVIEW Embedded Module for ADI Blackfin Processors is a comprehensive graphical development environment
Bracket and Mounting Dimensions
INSTALLATION GUIDE NI PS-14/15/16/17 Panel Mount Brackets This document provides the installation procedure for the NI PS-14/15/16/17 Panel Mount Brackets. Use accessory 199432-01 to mount NI PS-14/15/16/17
Traffic Offload. Cisco 7200/Cisco 7500 APPLICATION NOTE
APPLICATION NOTE Cisco 700/Cisco 700 Traffic offload allows exchange carriers to offload their telephony traffic to a packet network from the Public Switched Telephone Network (PSTN). By doing so, carriers
NI PXI Contents CALIBRATION PROCEDURE
CALIBRATION PROCEDURE NI PXI-5114 Contents This document contains instructions for writing an external calibration procedure for NI PXI-5114 digitizers. This calibration procedure is intended for metrology
LabVIEW DataFinder Toolkit
LabVIEW DataFinder Toolkit LabVIEW DataFinder Toolkit June 2009 375141A-01 Support Worldwide Technical Support and Product Information ni.com National Instruments Corporate Headquarters 11500 North Mopac
SCC-RLY01 Relay Module
USER GUIDE SCC-RLY01 Relay Module Conventions The SCC-RLY01 contains one single-pole double-throw (SPDT) nonlatching relay capable of switching 5 A at 30 VDC when using an SC-2345 or SC-2350, or 250 VAC
24-Channel, ±24 V Precision PXI Source Measure Unit
GETTING STARTED GUIDE PXIe-4163 24-Channel, ±24 V Precision PXI Source Measure Unit This document explains how to install, configure, and test the PXIe-4163. The PXIe-4163 ships with NI-DCPower driver
EventBuilder.com. International Audio Conferencing Access Guide. This guide contains: :: International Toll-Free Access Dialing Instructions
EventBuilder.com International Audio Conferencing Access Guide TM This guide contains: :: International Toll-Free Access Dialing Instructions :: ATFS (Access Toll-Free Service) Dialing Instructions ::