Migrating from MX29GL256E to MX29GL256F
|
|
|
- Geraldine Ellis
- 5 years ago
- Views:
Transcription
1 1. Introduction This application note describes the major differences between MX29GL256E and MX29GL256F. All the information in this document is based on the latest datasheet of the MX29GL256F and it will be subject to change if any further update from datasheet. 2. Feature Comparison Part Number MX29GL256E MX29GL256F VCC Range 2.7~3.6V 2.7~3.6V Package Feature 56-TSOP (14x20mm²) 64-FGBA/LFBGA (11x13mm²) 70-SSOP 56-TSOP (14x20mm²) 64-FGBA/LFBGA (11x13mm²) 70-SSOP 56FBGA (7x9mm²) Sector Architecture Uniform Sector 128KB Uniform Sector 128KB Page buffer Read 8Word (16Byte) 8Word (16Byte) Write 32Word (64Byte) 32Word (64Byte) Configuration x8 /x16 x8 / x16 CFI (Commom Flash Interface) Yes Yes Protection Security Sector 256 bytes 256 bytes Software Password protection Solid Protection, USPB (Note 1) Password protection Solid Protection, USPB (Note 1) Hardware WP# WP# Parameter Typ. Max. Min. Max. Access Time (Taa) Random ns 90ns (3.0~3.6) 100ns (2.7~3.6) 90ns (3.0~3.6) 100ns (2.7~3.6) Access Time (Taa) Page ns 25ns 25ns Word Program Time us Chip Program Time sec Sector Erase Time sec Chip Erase Time sec Total Write Buffer Time us Ace Total Write Buffer Time us Erase/Program Cycle cycles 100, ,000 Note 1. USPB = Temporary un-protect solid write protect bits. Publication Number: AN-077 1
2 3. DC Specifications Parameter MX29GL256E MX29GL256F Icr1, Read current (5MHz,mA) 50 (Max) 20 (Max) Icr2, Read current (10MHz,mA) 10 (Max) 5 (Max) Isb,Standby current (ua ) 100 (Max) 50 (Max) Isbr, Reset current 100 (Max) 50 (Max) Idpd, Deep power down current 10uA (Typical) 1uA (Typical) 4. AC Specifications Parameter MX29GL256E MX29GL256F Taa, Valid data output after address (ns) 90 /100 (Max.) 90 / 100 (Max.) Tce, Valid data output after CE# low (ns) 90 / 100 (Max.) 90 / 100 (Max.) Toe, Valid data output after OE# low (ns) 25 (Max.) 25 (Max.) Trc, Read period time (ns) 90 / 100 (Max.) 90 / 100 (Max.) Twc, Write period time (ns) 90 / 100 (Max.) 90 / 100 (Max.) Tcwc, Command period time (ns) 90 / 100 (Max.) 90 / 100 (Max.) 5. Manufacturer ID & Device ID Comparison Part Number MX29GL256E MX29GL256F Manufacturer ID 00C2h 00C2h Device ID (Word Mode) 227Eh / 2222h / 2201h 227Eh / 2222h / 2201h Publication Number: AN-077 2
3 6. Software Notices The MX29GL256F is command compatible with MX29GL256E such that it will be easy to migrate without any command change. The CFI code of MX2GL256F is the same as MX29GL256E. 7. References The following datasheets were used for preparing this comparison note: Datasheet Location Date Issued Version MX29GL256E Macronix Website Jul. 26, MX29GL256F Macronix Website Jan. 12, For more functional and parametric specifications, please refer to the datasheet on the Macronix Website at and go to: Products/Flash Memory/Parallel Flash. Publication Number: AN-077 3
4 REVISION HISTORY Revision No. Description Page Date Initial release JUL/20/ Added a new package - 56FBGA(7x9mm²) P1 OCT/07/ Updated parameters & DC specifications P1, 2 3. Updated Feature Comparison Table P1 Publication Number: AN-077 4
5 Except for customized products which have been expressly identified in the applicable agreement, Macronix's products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or household applications only, and not for use in any applications which may, directly or indirectly, cause death, personal injury, or severe property damages. In the event Macronix products are used in contradicted to their target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualified for its actual use in accordance with the applicable laws and regulations; and Macronix as well as it s suppliers and/or distributors shall be released from any and all liability arisen therefrom. Copyright Macronix International Co., Ltd All rights reserved, including the trademarks and tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit, NBiit, Macronix NBit, elite- Flash, HybridNVM, HybridFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC, Kingtech, MXSMIO, Macronix vee, Macronix MAP, Rich Au dio, Rich Book, Rich TV, and FitCAM. The names and brands of third party referred thereto (if any) are for identification purposes only. For the contact and order information, please visit Macronix s Web site at: MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice. 5
Industrial Temperature, 3 Volt, MCP Products - Parallel NOR Flash + Pseudo Static RAM (psram)
Industrial Temperature, 3 Volt, MCP Products - Parallel NOR Flash + Pseudo Static RAM (psram) 64Mb Page Mode Flash Memory (4M x 16Bit) and 32Mb psram (2M x 16Bit) MX69GL642E (Top Boot), MX69GL640E (Uniform
Comparing Spansion S29AL008J with Macronix MX29LV800C
1. Introduction Macronix MX29LV800C and Spansion S29AL008J 8Mb 3.0V parallel flash have similar features, performance, and command codes. This application note explains how to simply and easily compare
Comparing Spansion S29AL016J with Macronix MX29LV160D
1. Introduction Macronix MX29LV160D and Spansion S29AL016J 16Mb 3.0V parallel flash have similar features, performance, and command codes. This application note explains how to simply and easily compare
Comparing Toshiba TC58NVG0S3Exxxx with Macronix MX30LF1G08AA
1. Introduction Comparing Toshiba TC58NVG0S3Exxxx with Macronix MX30LF1G08AA APPLICATION NOTE This application note is to compare the Toshiba TC58NVG0S3Exxxx with Macronix MX30LF1G08AA, 3V 1Gb SLC NAND
Migrating from MX30LF1G08AA to MX30LF1GE8AB
Migrating from MX30LF1G08AA to MX30LF1GE8AB 1. Introduction This application note is a guide for migrating the Macronix MX30LF1G08AA to the MX30LF1GE8AB. The document does not provide detailed information
Migrating from MX60LF8G28AB to MX60LF8G18AC
Migrating from MX60LF8G28AB to MX60LF8G18AC 1. Introduction This application note is a guide for migrating Macronix from the MX60LF8G28AB to the MX60LF8G18AC. Both NAND devices are 8Gb SLC NAND Flash built
Comparing Toshiba TC58NVG1S3E with Macronix MX30LF2G18AC
1. Introduction This application note is a guide for migrating to the Macronix MX30LF2G18AC from the Toshiba TC58NVG1S3E 2Gb, 3V, NAND flash memory. The document does not provide detailed information on
Comparing Toshiba TC58BVG1S3HTAI0 with Macronix MX30LF2GE8AB
1. Introduction This application note is a guide for migrating to the Macronix MX30LF2GE8AB from the Toshiba TC58BVG1S3HTAI0 2Gb, 3V, Internal ECC NAND flash memory. The document does not provide detailed
Read-While-Write, Multiplexed, Burst Mode, Flash Memory
Read-While-Write, Multiplexed, Burst Mode, Flash Memory MX69V28F64 1 128M-BIT [8M x 16-bit] CMOS 1.8 Volt-only 1. FEATURES Characteristics Burst Length Burst Mode - Continuous linear Linear burst length
Macronix High Density Serial Flash Addressing
1. Introduction Many consumer products have converted or are converting from parallel flash to SPI serial flash. Generally, high end applications require higher memory density, but in the past, serial
Improving NAND Throughput with Two-Plane and Cache Operations
Improving NAND Throughput with Two-Plane and Cache Operations Introduction SLC NAND Flash memory is quickly being integrated into embedded systems for data and code storage. This technical note introduces
Migrating from MX30LF1G08AA to MX30LF1G18AC
Migrating from MX30LF1G08AA to MX30LF1G18AC 1. Introduction This application note is a guide for migrating from the Macronix MX30LF1G08AA to the MX30LF1G18AC SLC 3V NAND Flash. The document does not provide
Migrating from MX30LF2G(4G)28AB to MX30LF2G(4G)18AC
Migrating from MX30LF2G(4G)28AB to MX30LF2G(4G)18AC 1. Introduction This application note is a migration guide for migrating Macronix MX30LF2G(4G)28AB to MX30LF2G(4G)18AC 2Gb(4Gb) SLC NAND Flash. The document
Comparing Spansion S34ML04G100 with Macronix MX30LF4G18AC
1. Introduction This application note is a guide for migrating to the Macronix MX30LF4G18AC from the Spansion S34ML04G100 4Gb, 3V, NAND flash memory. The document does not provide detailed information
2. General Features The two devices have a different page size and block size. Feature differences are highlighted in Bold Italic type in Table 2-1.
1. Introduction This application note is a migration guide for comparing the Toshiba TC58NVG2S0F with the Macronix 4Gb SLC NAND Flash. The document does not provide detailed information on the individual
Both flash device families have similar features and functions as shown in Table 2-1.
1. Introduction This application note is a guide for migrating to the Macronix MX30LF1G08AA from the Spansion S34ML01G1 1Gb, 3V, NAND flash memory. The document does not provide detailed information on
Serial Flash Secured OTP Area Introduction
1. Introduction Macronix Serial Flash provides an additional 512 bits or 4K bits of secured OTP (One Time Programmable) memory that resides outside the main memory array. This OTP memory area provides
Macronix MX25Lxxx45G Serial Flash DTR Introduction
1. Introduction Macronix MX25Lxxx45G Serial NOR flash support DTR (Double Transfer Rate) Reads in the x1, x2, and x4 I/O modes. DTR allows address and data to be transferred on both the rising and falling
Comparison of MX25V4035F with MX25L4006E and MX25V4006E
1. Introduction Comparison of MX25V4035F with MX25L4006E and MX25V4006E This application note compares Macronix 4Mb, 2.5V/3V Serial NOR Flash MX25V4035F with MX25L4006E and MX25V4006E. Generally, the MX25V4035F
Comparison of MX25V8035F with MX25L8006E/08E and MX25V8006E
1. Introduction Comparison of MX25V8035F with /08E and MX25V8006E This application note compares Macronix 8Mb 2.5V/3V Serial NOR Flash MX25V8035F with MX25L8035/06/08E and MX25V8006E. Generally, the MX25V8035F
Comparison of MX25V1035F with MX25L1006E/1021E and MX25V1006E
Comparison of MX25V1035F with MX25L1006E/1021E and MX25V1006E 1. Introduction This application note compares Macronix 1Mb, 2.5V/3V Serial NOR Flash MX25V1035F with MX25L1006E/1021E and MX25V1006E. Generally,
Replacing Spansion S29GL_S with Macronix MX29GL_F
1. Introduction Macronix offers MX29GL_F high performance parallel flash in densities from 128Mb to 1Gb. MX29GL_F and Spansion S29GL_S devices have similar features, performance, and command codes. This
Comparing Micron N25Q128A with Macronix MX25L12835F
1. Introduction This application note serves as a guide to compare Micron N25Q128A with Macronix MX25L12835F 3V 128Mb SPI flash. The document does not provide detailed information on each individual device,
Comparison of MX25L3233F/73F/36F and MX25L32xxD/xxE
Comparison of 73F/36F and MX25L32xxD/xxE 1. Introduction This application note compares Macronix 75nm 32Mb 3V Serial NOR Flash 73F/36F with Macronix 110nm flash MX25L3235E and MX25L3206/8E and Macronix
Macronix Serial Flash Multi-I/O Introduction
1. Introduction All Macronix serial flash support a serial addressing protocol where 1 byte of instruction opcode is followed by a 3 byte (24 bit) address (note: may be a 4 byte address if the memory space
Comparison of MX25L6435E and MX25L6445E
Comparison of MX25L6435E and MX25L6445E APPLICATION NOTE 1. Introduction This application note compares MX25L6435E and MX25L6445E. The document does not provide detailed information on individual device,
How to handle the spare-byte area of Macronix 36nm NAND Flash
How to handle the spare-byte area of Macronix 36nm NAND Flash Some NAND Flash come with a non-standard spare area that is larger than what is commonly used by Linux for error correction. MX30LF2G28AB and
Comparison of MX25U4033E and MX25U4035
Comparison of MX25U4033E and MX25U4035 1. Introduction This application note compares MX25U4033E and MX25U4035. The document does not provide detailed information on individual devices, but highlights
Comparison of MX25L6433F/73F/36F and MX25L64xxE
Comparison of /73F/36F and MX25L64xxE 1. Introduction This application note compares Macronix 75nm 64Mb Serial NOR Flash /73F/36F with Macronix MX25L64xxE 110nm Serial flash. Generally, the /73F/36F is
Migrating from MX25U25635F to MX25U25645G
Migrating from MX25U25635F to MX25U25645G 1. Introduction This document highlights parameters which may require attention when migrating from the MX25U25635F (75nm F Version) to the MX25U25645G (55nm G
Using Erase Suspend and Erase Resume Functions in NOR Flash
Using Suspend and Resume Functions in OR Flash Introduction The Suspend function can be used to temporarily stop an operation to allow for the reading or programming of other blocks in the same Flash memory.
SLC NAND FLASH and LPDDR2 162-Ball MCP (Multi-Chip Package)
SLC NND FLSH and LPDDR2 162-Ball MCP (Multi-Chip Package) Key Features NND Flash Features: Low Power Dissipation High Reliability 1 Contents 1. MCP FETURES...3 2. BLOCK DIGRM...4 3. PRT NME DESCRIPTION...5
Comparing Micron N25Q032A / N25Q064A with Macronix MX25U3235F / MX25U6435F
1. Introduction This application note serves as a guide to compare the Micron N25Q032A and N25Q064A with the Macronix MX25U3235F and MX25U6435F 1.8V 32Mb and 64Mb Serial Flash. The document does not provide
Migrating from MX25L25635F to MX25L25645G/MX25L25673G
Migrating from to / 1. Introduction This document highlights parameters which may require attention when migrating from the (75nm F Version) to the and (55nm G Version). Generally, the G version is backward
The Comparison of MX25L12835E/36E/45E and MX25L12835F/33F
The Comparison of MX25L12835E/36E/45E and MX25L12835F/33F APPLICATION NOTE 1 Introduction This application note compares Macronix MX25L12835E/36E/45E/35F/33F Serial NOR Flash products The document does
Comparing Micron N25Q128A with Macronix MX25U12835F
1. Introduction This application note serves as a guide to compare Micron N25Q128A with Macronix MX25U12835F 1.8V 128Mb SPI flash. The document does not provide detailed information on each individual
APPLICATION NOTE Migrating to MX25L1606E / MX25L8006E from MX25L1605D / MX25L8005
Publication Number: AN-055 Contents 1. Introduction...2 2. General Features...3 2-1. Feature Comparison...3 Table 2-1: Major Feature Comparison of 8Mb Devices...3 Table 2-2: Major Feature Comparison of
MX25L5121E MX25L1021E MX25L5121E, MX25L1021E DATASHEET
MX25L5121E, DATASHEET 1 Contents FEATURES... 4 GENERAL... 4 PERFORMANCE... 4 FTWARE FEATURES... 4 HARDWARE FEATURES... 4 GENERAL DESCRIPTION... 5 PIN CONFIGURATIONS... 6 PIN DESCRIPTION... 6 BLOCK DIAGRAM...
MX30LF1208AA 512M-bit NAND Flash Memory
MX30LF1208AA 512M-bit NAND Flash Memory 1 Contents 1. FEATURES...4 2. GENERAL DESCRIPTIONS...4 Figure 1. MX30LF1208AA Logic Diagram... 4 2-1. ORDERING INFORMATION...5 3. PIN CONFIGURATIONS...6 3-1. PIN
KH25L5121E. Key Features KH25L5121E. 3V, 512K-BIT [x 1] CMOS SERIAL FLASH MEMORY
![KH25L5121E. Key Features KH25L5121E. 3V, 512K-BIT [x 1] CMOS SERIAL FLASH MEMORY](/thumbs/72/67182947.jpg "KH25L5121E. Key Features KH25L5121E. 3V, 512K-BIT [x 1] CMOS SERIAL FLASH MEMORY")
KH25L5121E 3V, 512K-BIT [x 1] CMOS SERIAL FLASH MEMORY Key Features Block Lock protection Hardware write protection Auto Erase and Auto Program Algorithm Low Power Consumption 1 Contents FEATURES... 4
Comparing Spansion S26KS512S with Macronix MX25UM51245G
1. Introduction This application note compares the 512Mb 1.8V OctaFlash serial flash and the Spansion S26KS512S parallel flash devices. This document does not provide detailed information on each individual
APPLICATION NOTE Migrating to MX25L3206E from MX25L3205D
Migrating to MX25L3206E from MX25L3205D Publication Number: AN-058 1. Introduction This application note introduces the related notices for migrating to MX25L3206E from MX25L3205D. The document does not
NAND Design-In Notice
1. Introduction NAND flash process migration is fast. On average, it only takes 1 ~ 2 years before the next process migration is ready to provide cost reductions for general embedded system applications,
MX29F800C T/B. 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY FEATURES
![MX29F800C T/B. 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY FEATURES](/thumbs/87/96215426.jpg "MX29F800C T/B. 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY FEATURES")
FEATURES 8M-BIT [1024K x 8 / 512K x 16] SINGLE VOLTAGE 5V ONLY FLASH MEMORY GENERAL FEATURES Single Power Supply Operation - 4.5 to 5.5 volt for read, erase, and program operations 1,048,576 x 8 / 524,288
Migrating from Macronix MX29GL-G/F and MX68GL-G Devices to MT28EW NOR Flash Devices
Technical Note TN-13-38: Migrating MX29GL-G/F and MX68GL-G to MT28EW Introduction Migrating from Macronix MX29GL-G/F and MX68GL-G Devices to MT28EW Introduction This technical note describes the process
MX29GL512E H/L MX29GL512E H/L DATASHEET
MX29GL512E H/L DATASHEET The MX29GL512E product family is not recommended for new designs. The MX29GL512F family is the recommended replacement. Please refer to MX29GL512F datasheet for full specifications
MX25V1006E DATASHEET
MX25V1006E DATASHEET 1 Contents FEATURES... 4 GENERAL... 4 PERFORMANCE... 4 SOFTWARE FEATURES... 4 HARDWARE FEATURES... 5 GENERAL DESCRIPTION... 5 PIN CONFIGURATIONS... 6 8-LAND USON (2x3mm)... 6 8-PIN
MX35LF1GE4AB MX35LF2GE4AB. 3V, 1Gb/2G-bit Serial NAND Flash Memory. MX35LFxGE4AB. P/N: PM2128 REV. 1.5, June 07,
3V, 1Gb/2G-bit Serial NAND Flash Memory MX35LFxGE4AB 1 Contents 1. FEATURES...5 2. GENERAL DESCRIPTIONS...6 Figure 1. Logic Diagram... 6 3. ORDERING INFORMATION...7 4. BALL ASGNMENT AND DESCRIPTIONS...8
Comparing Spansion S25FL512S with Macronix MX66L51235F
Comparing with 1. Introduction This application note compares the and serial flash devices. This document does not provide detailed information on each individual device, but highlights the similarities
MX68GL1G0F H/L-70SSOP MX68GL1G0F H/L (70SSOP) DATASHEET
MX68GL1G0F H/L (70SSOP) DATASHEET 1 Contents 1. FEATURES... 6 2. PIN CONFIGURATION... 7 3. PIN DESCRIPTION... 7 4. BLOCK DIAGRAM... 8 5. BLOCK DIAGRAM DESCRIPTION... 9 6. BLOCK STRUCTURE... 10 7. BUS OPERATION...11
Quick Guide to Common Flash Interface
Quick Guide to Common Flash Interface Application By: Frank Cirimele 1. Introduction Common Flash Interface, or CFI, is a standard introduced by the Joint Electron Device Engineering Council (JEDEC) to
MX29GL256E MX29GL256E DATASHEET
MX29GL256E DATASHEET The MX29GL256E product family is not recommended for new designs, while MX29GL256F family is suggested to replace it. Please refer to MX29GL256F datasheet for specifications and ordering
MX29GL128F MX29GL128F DATASHEET
MX29GL128F DATASHEET 1 Contents FEATURES...5 PIN CONFIGURATION...6 PIN DESCRIPTION...7 BLOCK DIAGRAM...8 BLOCK DIAGRAM DESCRIPTION...9 BLOCK STRUCTURE...10 Table 1: SECTOR ARCHITECTURE...10 BUS OPERATION...
MX29GL640E T/B, MX29GL640E H/L DATASHEET
MX29GL640E T/B, DATASHEET 1 Contents FEATURES...5 PIN CONFIGURATION for MX29GL640E T/B...6 PIN CONFIGURATION for...7 PIN DESCRIPTION...8 BLOCK DIAGRAM...9 BLOCK DIAGRAM DESCRIPTION...10 BLOCK STRUCTURE...
Conversion Guide (256-Mbit): Numonyx Embedded Flash Memory (J3 v. D, 130 nm) to Numonyx StrataFlash Embedded Memory (J3-65 nm)
Conversion Guide (256-Mbit): Numonyx Embedded Flash Memory (J3 v. D, 130 nm) to Numonyx StrataFlash Embedded Memory (J3-65 nm) Application Note - 308041 December 2008 308041-01 INFORMATION IN THIS DOCUMENT
Comparing Spansion S25FL512S with Macronix MX25L51245G
Comparing Spansion with Macronix 1. Introduction This application note compares the Macronix and Spansion serial flash devices. This document does not provide detailed information on each individual device,
AN Migration Guide
AN309006 Migration Guide How to Migrate to Numonyx M29W800D from Spansion* S29AL008J/D Flash Memory This application note explains how to migrate an application based on the Spansion* 1 S29AL008D/J Flash
AN2685 Application note
Application note How to migrate from S29GL128P to M29W128GH/L Flash memories Introduction The objective of this application note is to explain how to migrate an application based on the S29GL128P Flash
AN2663 Application note
Application note How to migrate from M29W128FH/L to M29W128GH/L Flash memories Introduction The objective of this application note is to explain how to migrate an application based on the M29W128FH/L Flash
AN3102 Application note
Application note How to migrate from M29DW128FH/L to M29DW128GH/L Flash memories Introduction The objective of this application note is to explain how to migrate an application based on the M29DW128FH/L
W29N08GV W29N08GV NAND FLASH MEMORY. 2 chip stack 8G-Bit. Release Date: August 26 th Revision A
2 chip stack 8G-Bit W29N08GV NAND FLASH MEMORY 1 Revision A Table of Contents 1. GENERAL DESCRIPTION... 3 2. PACKAGE TYPES AND PIN CONFIGURATIONS... 4 3. MEMORY ARRAY ORGANIZATION... 8 4. DEVICE ID...
PRODUCT SELECTION GUIDE
PRODUCT SELECTION GUIDE July, 2014 Your Partner in Innovation Today and Tomorrow for 02 About Macronix 04 Serial NOR Flash 10 Parallel NOR Flash 12 NAND Flash Memory 14 Secure Flash 15 WLCSP (Wafer-Level
Migrating from Spansion Am29F to Micron M29F NOR Flash Memories
Technical Note Introduction Migrating from Spansion Am29F to Micron M29F Memories Introduction This technical note explains the process for migrating an application based on Spansion Am29F200B, Am29F400B,
MX23L M-BIT MASK ROM (8/16-BIT OUTPUT) FEATURES PIN CONFIGURATION PIN DESCRIPTION 44 SOP ORDER INFORMATION
32M-BIT MASK ROM (8/16-BIT OUTPUT) FEATURES Bit organization - 4M x 8 (byte mode) - 2M x 16 (word mode) Fast access time - Random access: 70ns (max.) - Page access: 25ns (max.) Page Size - 8 words per
Technical Note. Migrating from Cypress's FL-S and FS-S to Micron's MT25Q. Introduction
Technical Note TN-25-37: Migrating from Cypress's FL-S and FS-S to Micron's Introduction Migrating from Cypress's FL-S and FS-S to Micron's Introduction This technical note describes the process for converting
MX29GL256F H/L-70SSOP MX29GL256F H/L (70 SSOP) DATASHEET
MX29GL256F H/L (70 SSOP) DATASHEET 1 SINGLE VOLTAGE 3V ONLY FLASH MEMORY FEATURES GENERAL FEATURES Power Supply Operation - 2.7 to 3.6 volt for read, erase, and program operations Byte/Word mode switchable
Technical Note. Migrating from Micron M29W Devices to MT28EW NOR Flash Devices. Introduction. TN-13-50: Migrating M29W to MT28EW NOR Flash Devices
Technical Note Migrating from Micron Devices to NOR Flash Devices TN-13-50: Migrating to NOR Flash Devices Introduction Introduction This technical note describes the process for converting a system design
AN Migration Guide
AN309005 Migration Guide How to Migrate to Numonyx M29W400D from Spansion* S29AL004D Flash Memory This application note explains how to migrate an application based on the Spansion* 1 S29AL004D flash memory
W29GL256S 256M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE. Publication Release Date: Jul 02, 2014 Revision C
256M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE 1 TABLE OF CONTENTS 1 General Description... 8 2 FEATURES... 8 3 PIN CONFIGURATION... 9 4 BLOCK DIAGRAM... 10 5 PIN DESCRIPTION... 11 6 Introduction...
How to migrate to Numonyx Axcell M29EW (SBC) from Spansion S29GL flash (32-, 64- and 128-Mbit) Application Note May 2010
How to migrate to Numonyx Axcell M29EW (SBC) from Spansion S29GL flash (32-, 64- and 128-Mbit) Application Note - 309014 May 2010 Application Note May 2010 1 309014-02 Table of Contents Revision History.....................................................
MX29GL512G/MX68GL1G0G DATASHEET
MX29GL512G/ DATASHEET 1 Contents 1. FEATURES...6 2. PIN CONFIGURATION...8 3. PIN DESCRIPTION...9 4. BLOCK DIAGRAM...10 5. BLOCK DIAGRAM DESCRIPTION... 11 6. BLOCK STRUCTURE...12 7. BUS OPERATION...13 8.
Migration Guide for Numonyx StrataFlash Wireless Memory (L18/L30) to Numonyx StrataFlash Embedded Memory (P30)
Migration Guide for Numonyx StrataFlash Wireless Memory (L18/L30) to Numonyx StrataFlash Embedded Memory (P30) Application Note - 840 November 2007 309083-03 INFORMATION IN THIS DOCUMENT IS PROVIDED IN
FEATURES. Single Power Supply Operation - Low voltage range: 2.70 V V
FEATURES Single Power Supply Operation - Low voltage range: 2.70 V - 3.60 V - IS39LV040: 512K x 8 (4 Mbit) - IS39LV010: 128K x 8 (1 Mbit) - IS39LV512: 64K x 8 (512 Kbit) - 70 ns access time - Uniform 4
GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family
GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family IS29GL01GS 1 Gbit (128 Mbyte) IS29GL512S 512 Mbit (64 Mbyte) IS29GL256S 256 Mbit (32 Mbyte) CMOS 3.0 Volt Core with Versatile I/O Data GL-S MirrorBit
Am29F040B. Data Sheet Supplement for PROM Programmer Manufacturers. SECTOR PROTECTION/ UNPROTECTION FOR Am29F040B. Sector Unprotection
SUPPLEMENT Am29F040B Data Sheet Supplement for PROM Programmer Manufacturers This supplement is for use with the Am29F040B data sheet, publication number 21445, and describes the sector protection and
Technical Note. Migrating from Micron M25PE to Micron MT25Q 128Mb. Introduction. TN-25-36: Migrating from M25PE to MT25Q 128Mb.
Technical Note TN-25-36: Migrating from to MT25Q 128Mb Introduction Migrating from Micron to Micron MT25Q 128Mb Introduction The purpose of this technical note is to compare the features of Micron Flash
Comparing Micron N25Q and Macronix MX25L Flash Devices
Technical Note TN-12-14: Comparing and Flash Devices Introduction Comparing Micron and Macronix Flash Devices Introduction The purpose of this technical note is to compare features of the Micron (32Mb
Technical Note. Migrating from Micron M25P to Micron MT25Q 128Mb. Introduction. TN-25-34: Migrating from M25P to MT25Q 128Mb.
Technical Note TN-25-34: Migrating from to MT25Q 128Mb Introduction Migrating from Micron to Micron MT25Q 128Mb Introduction The purpose of this technical note is to compare the features of Micron Flash
MX29F040C. 4M-BIT [512K x 8] SINGLE VOLTAGE 5V ONLY FLASH MEMORY FEATURES
![MX29F040C. 4M-BIT [512K x 8] SINGLE VOLTAGE 5V ONLY FLASH MEMORY FEATURES](/thumbs/76/74295373.jpg "MX29F040C. 4M-BIT [512K x 8] SINGLE VOLTAGE 5V ONLY FLASH MEMORY FEATURES")
FEATURES 4M-BIT [512K x 8] SINGLE VOLTAGE 5V ONLY FLASH MEMORY GENERAL FEATURES Single Power Supply Operation - 4.5 to 5.5 volt for read, erase, and program operations 524288 x 8 only Sector Structure
64M-BIT Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI
FM25Q64 64M-BIT Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI 1 Documents title 64M bit Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI Revision History Revision No. History Draft
PCMCIA Flash Memory Card
Eight Bit Flash Memory Card (Intel based) General Description 512KB, 1, 2, 4 and 8 MEGABYTE Features The FEA Econo Flash card series offers a low cost and high performance eight bit linear Flash solid
Technical Note. Migrating from S29GL-S Devices to MT28FW NOR Flash Devices. Introduction. TN-13-41: Migrating S29GL-S to MT28FW NOR Flash Devices
Technical Note Migrating from S29GL-S Devices to MT28FW NOR Flash Devices TN-3-: Migrating S29GL-S to MT28FW NOR Flash Devices Introduction Introduction This technical note describes the process for converting
GLS29EE512 Small-Sector Flash 512 Kbit (64K x8) Page-Write EEPROM
Features Single Voltage Read and Write Operations - 4.5-5.5V for GLS29EE512 Superior Reliability - Endurance: 100,000 Cycles (typical) - Greater than 100 years Data Retention Low Power Consumption - Active
W25X05CL/10CL/20CL 2.5 / 3 / 3.3 V 512K / 1M / 2M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI
2.5 / 3 / 3.3 V 512K / 1M / 2M-BIT SERIAL FLASH MEMORY WITH 4KB SECTORS AND DUAL I/O SPI - 1 - Revision B Table of Contents 1. GENERAL DESCRIPTION...4 2. FEATURES...4 3. PIN CONFIGURATION SOIC 150-MIL,
VSS VSS D15/A-1 D7 D14 D6 D13 D5 D12 D4 VCC VCC VSS VSS NC A18 A17 A7 A6 A5 A4 A3 A2 A1 A0 CE BYTE A16 A15 A14 A13 A12 A11 A10 A19 VSS A21 A20
5 Volt 16-Mbit (2M x 8 / 1M x 16) Mask ROM FEATURES Bit organization - 2M x 8 (byte mode) - 1M x 16 (word mode) Fast access time - Random access: 100ns (max.) Current - Operating: 60mA - Standby: 50uA
W29GL032C 32M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE. Publication Release Date: August 2, 2013 Revision H
32M-BIT 3.0-VOLT PARALLEL FLASH MEMORY WITH PAGE MODE Publication Release Date: August 2, 2013 Revision H BLANK Table of Contents 1 GENERAL DESCRIPTION... 1 2 FEATURES... 1 3 PIN CONFIGURATIONS... 2 4
FM25Q08 FM25Q08. 8M-BIT Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI. preliminary(aug ) 1
FM25Q08 8M-BIT Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI 1 Documents title 8M bit Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI Revision History Revision No. History Draft
GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family
GL-S MirrorBit Eclipse Flash Non-Volatile Memory Family S29GL01GS 1 Gbit (128 Mbyte) S29GL512S 512 Mbit (64 Mbyte) S29GL256S 256 Mbit (32 Mbyte) S29GL128S 128 Mbit (16 Mbyte) CMOS 3.0 Volt Core with Versatile
Pm39F010 / Pm39F020 / Pm39F040
1 Mbit / 2 Mbit / 4 Mbit 5 Volt-only CMOS Flash Memory FEATURES Single Power Supply Operation - Low voltage range: 4.5 V - 5.5 V Memory Organization - Pm39F010: 128K x 8 (1 Mbit) - Pm39F020: 256K x 8 (2
3.3V Uniform Sector Dual and Quad Serial Flash GD25Q80C DATASHEET
DATASHEET 1 Contents 1. FEATURES... 4 2. GENERAL DESCRIPTION... 5 3. MEMORY ORGANIZATION... 7 4. DEVICE OPERATION... 8 5. DATA PROTECTION... 9 6. STATUS REGISTER... 11 7. COMMANDS DESCRIPTION... 13 7.1.
Parallel NOR Flash Embedded Memory
Parallel NOR Flash Embedded Memory M29W256GH, M29W256GL 256Mb: 3V Embedded Parallel NOR Flash Features Features Supply voltage V CC = 2.7 3.6V (program, erase, read) V CCQ = 1.65 3.6V (I/O buffers) V PPH
W25Q32DW 1.8V 32M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI. Publication Release Date: May 22, Revision E
1.8V 32M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI Publication Release Date: May 22, 2014-1 - Revision E Table of Contents 1. GENERAL DESCRIPTION... 5 2. FEATURES... 5 3. PIN CONFIGURATION SOIC
MOS INTEGRATED CIRCUIT
DATA SHEET 4M-BIT CMOS STATIC RAM 256K-WORD BY 16-BIT EXTENDED TEMPERATURE OPERATION MOS INTEGRATED CIRCUIT µpd444012a-x Description The µpd444012a-x is a high speed, low power, 4,194,304 bits (262,144
3 Volt Intel StrataFlash Memory to i960 H CPU Design Guide
3 Volt Intel StrataFlash Memory to i960 H CPU Design Guide Application Note 705 April 2000 Document Number: 292253-002 Information in this document is provided in connection with Intel products. No license,
W25Q16CL 2.5V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI. Publication Release Date: May 23, Revision G
2.5V 16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI Publication Release Date: May 23, 2014-1 - - Revision G Table of Contents 1. GENERAL DESCRIPTION... 5 2. FEATURES... 5 3. PACKAGE TYPES... 6 3.1
Uniform Sector Dual and Quad Serial Flash GD25Q80B DATASHEET
DATASHEET 1 Contents 1. FEATURES... 4 2. GENERAL DESCRIPTION... 5 3. MEMORY ORGANIZATION... 7 4. DEVICE OPERATION... 8 5. DATA PROTECTION... 9 6. STATUS REGISTER... 11 7. COMMANDS DESCRIPTION... 13 7.1.
Migrating from Spansion S25FL512S to Micron N25Q 512Mb Flash Device
Technical Note TN-12-21: Migrating to Micron 512Mb Flash Device Introduction Migrating from Spansion 512S to Micron 512Mb Flash Device Introduction The purpose of this technical note is to compare features
2-Megabit (256K x 8) 5-volt Only CMOS Flash Memory AT29C020. Features. Description. Pin Configurations
Features Fast Read Access Time - 90 ns 5-Volt-Only Reprogramming Sector Program Operation Single Cycle Reprogram (Erase and Program) 1024 Sectors (256 bytes/sector) Internal Address and Data Latches for
32M-BIT Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI
FM25Q32 32M-BIT Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI Rev.06 (May.20.2011) 1 Documents title 32M bit Serial Flash Memory with 4KB Sectors, Dual and Quad I/O SPI Revision History Revision
MX27C K-BIT [32K x 8] CMOS EPROM FEATURES GENERAL DESCRIPTION BLOCK DIAGRAM PIN CONFIGURATIONS PIN DESCRIPTION
![MX27C K-BIT [32K x 8] CMOS EPROM FEATURES GENERAL DESCRIPTION BLOCK DIAGRAM PIN CONFIGURATIONS PIN DESCRIPTION](/thumbs/78/78720826.jpg "MX27C K-BIT [32K x 8] CMOS EPROM FEATURES GENERAL DESCRIPTION BLOCK DIAGRAM PIN CONFIGURATIONS PIN DESCRIPTION")
FEATURES 32K x 8 organization Single +5V power supply +125V programming voltage Fast access time: 45/55/70/90/100/120/150 ns Totally static operation Completely TTL compatible 256K-BIT [32K x 8] CMOS EPROM