INSTALLATION INSTRUCTIONS FOR THE BV10-100/1000

Size: px
Start display at page:

Download "INSTALLATION INSTRUCTIONS FOR THE BV10-100/1000"

Transcription

1 INSTALLATION INSTRUCTIONS FOR THE BV10-100/1000 This document describes the basic steps for installing your BV or BV For detailed information about the BV10-100/1000, see the Ethernet Performance Endpoints BV and BV User Guide. In this document This document contains the following sections: Section Page Front Panel Description 2 Installing the Units in a Rack 3 Connecting the Power 4 Connecting the Test Interface Ports 8 Connecting the Management Interfaces 11

2 2 Installation Instructions for the BV10-100/1000 Front Panel Description The following figures show the locations of all connectors, ports, and s available on the front panel of the BV and BV units. BV version Test port s Speed Link/Activity LAN port s Speed Link/Activity Console port Status Test port LAN port Power BV version Electrical Test port s Speed Link/Activity LAN port s Speed Link/Activity Optical Test port Console port Status Test port LAN port Power Link/Activity Laser Optical Test port s

3 Installation Instructions for the BV10-100/ Installing the Units in a Rack The BV10-100/1000 can be mounted in a rack using the rack mount accessory kit (ordered separately). The accessory kit shelf holds up to four BV10-100/1000s. To install the BV10-100/1000 in a rack: 1 Attach the brackets of the supplied shelf unit to your rack using the supplied screws. 2 If cables have been attached to the BV10-100/1000, disconnect all of them as well as the ground lug from the unit. 3 Slide the unit into the desired slot from front to back. 4 With the unit completely inserted into the slot, tighten the thumb screw at the back of the unit. Thumb screw 5 Connect all cables and the ground lug, as explained in the next sections.

4 4 Installation Instructions for the BV10-100/1000 Connecting the Power The BV10-100/1000 is available with either an external brick AC power supply or an integrated DC power supply. Both AC and DC units are shipped with a grounding lug and hardware attached. The external brick AC power supply receives AC power through an IEC C14 power cord and delivers it to the BV10-100/1000 through a DC barrel type coaxial power connector. Acceptable AC input is VAC / ±10 %; 50-60Hz. Typical output voltage of the external brick AC power supply to the BV10-100/1000 is 9V DC. As soon as the BV10-100/1000 is connected to a live power supply, the POWER turns on. (If the POWER does not turn on, there is a power failure at the source or the unit is damaged.) The STATUS indicates whether or not the unit is ready for use. If the STATUS is not on, the unit is booting up. If it is green, red, or orange, the unit has booted. Grounding the BV10-100/1000 The BV10-100/1000 is shipped with a ground lug and hardware attached to the back of the unit. The grounding hardware consists of a washer with external teeth facing the unit and a locking nut. You will need to supply a #6 AWG wire. WARNING The BV10-100/1000 DC version is intended to be grounded. Ensure that the unit is connected to earth ground during normal use.

5 Installation Instructions for the BV10-100/ Ground lug AC unit Ground lug and hardware Ground lug DC unit Ground lug and hardware How to ground the BV10-100/1000 To ground the BV10-100/1000: 1 Loosen the locking nut on the grounding lug. 2 Using a #6 AWG wire, twist the wire around the lug so that it is touching the flat surface of the washer. The wire must be twisted between the washer and the locking nut. 3 Tighten the locking nut. 4 Connect the other end of the wire to the ground distribution network. Connecting the BV10-100/1000 to an AC Power Source This section explains how to connect power to a BV10-100/1000 equipped with AC power. How to connect an AC unit To connect the BV10-100/1000 to an AC power source: 1 Connect the supplied AC power cord to the BV10-100/1000 side panel through an IEC C14 connector. 2 Connect the other end of the power supply to the DC barrel-type coaxial power connector on the BV10-100/1000.

6 6 Installation Instructions for the BV10-100/1000 Connecting the BV10-100/1000 to a DC Power Source This section explains how to connect power to a BV10-100/1000 equipped with DC power. The unit is equipped with either +24V DC or -48V DC. WARNING Powering a BV10-100/ V DC unit with a -48V power source will permanently damage the unit. The +24V input range is 20-32V. WARNING Powering a BV10-100/ V DC unit with a +24V power source will permanently damage the unit. The -48V input range is 40-72V. How to connect a DC unit To connect the BV10-100/1000 to a DC power source: 1 Using AWG copper insulated wires and the supplied connector, insert the two stripped wires into the connector and tighten the screws firmly. Be sure to respect the polarity. The positive supply wire lead (40-72V for a -48V unit or 20-32V for a +24V unit) must be on the right side of the lug and the negative supply wire on the left side. The following figures show the -48V and +24V DC units. -48V DC Unit: Supplied connector Negative (-) supply wire lead on the left Positive (+) supply wire lead on the right

7 Installation Instructions for the BV10-100/ V DC Unit: Supplied connector Negative (-) supply wire lead on the left Positive (+) supply wire lead on the right 2 Connect the plug to one of the two DC input connectors on the BV10-100/1000 unit and tighten the screws firmly. 3 Connect the other end of the wires to the DC power source. CAUTION The DC input feeds to the equipment must be protected by 20A rated maximum breaker provided as part of the building installation. 4 To add a redundant DC power source on the BV10-100/1000, repeat step 1 through step 3.

8 8 Installation Instructions for the BV10-100/1000 Connecting the Test Interface Ports The BV provides an electrical 10/100Mbps Ethernet Test interface. The BV provides an electrical 10/100/1000Mbps Ethernet Test interface and an optical SFP laser Ethernet Test interface. The two BV Test interfaces are mutually exclusive. Management through the Test port The BV10-100/1000 can be managed in-band through the Test port. In-band management is provided for key tasks, such as basic configuration and software upgrades, in situations where the Management port is not accessible. It is important to note that in-band management through the Test port should be performed with low traffic volume so that management responses have minimal impact on test traffic. With high traffic volume, management responses might add jitter/latencey or dropped packets to results. The console in-band enable disable command controls in-band management on the Test port. By default, in-band management on the Test port is enabled. The following test activities are automatically disabled during software upgrade on the Test port: Smart Loopback TWAMP Light Responder UDP Echo Responder Ethernet OAM Handling State and configuration settings are preserved and restored when the software upgrade is complete and the BV10-100/1000 is rebooted.

9 Installation Instructions for the BV10-100/ Connecting the Electrical 10/100/1000Mbps Ethernet Test Interface BV The BV10-100/1000 has one electrical RJ-45 port for 10Base-T, 100Base-TX, and 1000Base-T testing capability. Note: 1000Base-T is available on the BV only. Electrical 10/100Mbps BV Electrical 10/100/1000Mbps How to connect the electrical test interface To use the 10/100/1000Mbps electrical interface for testing or management, connect the 10/100/1000Mbps electrical signal to the BV10-100/ /100/1000Mbps port using a CAT 5 or better unshielded twisted pair (UTP) cable with an RJ-45 connector.

10 10 Installation Instructions for the BV10-100/1000 Connecting the Optical SFP 1000Mbps Ethernet Test Interfaces The BV provides an optional optical port for 1000Base-SX/LX/ ZX testing capability. The optical port is a Small Form Factor Pluggable (SFP) slot type that uses an LC connector. CAUTION To ensure that the maximum receiver level is not exceeded, an attenuator might be needed. Optical SFP 1000Mps How to connect the optical test interface To use the 1000Mbps optical interface for testing or management: 1 Insert one of the following SFP modules into the optical slot. Rate 1000Base-X 850nm 1000Base-X 1300nm 1000Base-X 1550nm Description SFP module for 1000Base-SX short wavelength laser connection SFP module for 1000Base-LX long wavelength laser connection SFP module for 1000Base-ZX extended wavelength laser connection 2 Carefully connect the optical fiber cables to the SFP IN and OUT ports. To ensure good signal quality, make sure that the optical fiber connector is fully inserted into the optical connector port. Note: To ensure that the maximum receiver power level is not exceeded, an attenuator must be used.

11 Installation Instructions for the BV10-100/ Connecting the Management Interfaces You can connect the Management interface either locally using the Console port or remotely using the LAN port. Connecting the Console Port BV Console port Connecting a PC to the Console port, a standard RS-232 DE-9F DCE connection (commonly known as DB-9), provides local access to the BV10-100/1000 user interface. The connection configuration is 9600bps, 8 data bits, no parity, 1 stop bit (9600/8-N-1). The Console port is always enabled for CLI use. Console port BV Console port Console port How to connect the Console port To connect locally to the BV10-100/1000 using the Console port, connect a PC to the Console port using an RS-232 straight cable with a DB-9 connector.

12 12 Installation Instructions for the BV10-100/1000 Connecting the Ethernet LAN Port BV LAN port Connecting a typical management network to the 10/100Mbps Ethernet LAN port provides remote access to the BV10-100/1000 command line interface (CLI). Either Telnet or SSH can be used and must be enabled. To connect to the LAN port using Telnet or SSH, the IP address must be known. The default address for the LAN port is IP address: Netmask: BV LAN port 10/100Mbps Ethernet LAN port 10/100Mbps Ethernet LAN port How to connect the LAN port To connect remotely to the BV10-100/1000 using the LAN port, connect both the BV10-100/1000 LAN port and the remote PC to the same Management network using a standard straight through Ethernet cable with an RJ-45 connector.

BV10. Performance Endpoint Unit. User Guide

BV10. Performance Endpoint Unit. User Guide BV10 Performance Endpoint Unit User Guide Copyright 2010 2014 EXFO Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, be it

More information

ICPDAS FSM-510G Series Ethernet Management Switch Quick Start

ICPDAS FSM-510G Series Ethernet Management Switch Quick Start ICPDAS FSM-510G Series Ethernet Management Switch Quick Start Version 1.0, Dec 2014 Overview The Management Ethernet Switch solutions are designed for supporting standard industrial applications. Managed

More information

8~14-Port Managed Ethernet Switch

8~14-Port Managed Ethernet Switch 8~14-Port Managed Ethernet Switch Quick Installation Guide Overview The Managed Ethernet Switch solutions are designed for supporting standard industrial applications. Managed switches are easier to prioritize,

More information

FSM-510G Series Ethernet Management Switch Quick Start Guide

FSM-510G Series Ethernet Management Switch Quick Start Guide FSM-510G Series Ethernet Management Switch Quick Start Guide Overview The Management Ethernet Switch solutions are designed for supporting standard industrial applications. Managed switches are easily

More information

Quick Start. This document describes how to install the Juniper Networks PTX5000 Packet Transport

Quick Start. This document describes how to install the Juniper Networks PTX5000 Packet Transport PTX5000 Packet Transport Router Quick Start September 2017 Part Number: 530-066788 Revision 01 This document describes how to install the Juniper Networks PTX5000 Packet Transport Router. Contents Quick

More information

Quick Start Guide. C-100 Series Switches

Quick Start Guide. C-100 Series Switches Quick Start Guide C-100 Series Switches C-100 SERIES QUICK START GUIDE Warnings and Cautionary Messages!! Warning: This product does not contain any serviceable user parts. Warning: Installation and removal

More information

INDUSTRIAL POE SWITCH

INDUSTRIAL POE SWITCH STEP X - Name of Step QUICK START GUIDE LIE1014A, LIE1080A, LIE1082A INDUSTRIAL POE SWITCH 24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM STEP 1 - Hardware Description LIE1014A LIE1080A TABLE

More information

Cisco ONS CL Shelf Assembly Hardware

Cisco ONS CL Shelf Assembly Hardware CHAPTER 1 This chapter provides a description of Cisco ONS 15310-CL shelf hardware. Instructions for installing equipment are provided in the Cisco ONS 15310-CL and Cisco ONS 15310-MA Procedure Guide.

More information

INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS. KCD-400 Series. Installation Guide

INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS. KCD-400 Series. Installation Guide INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS KCD-400 Series Installation Guide DOC.060227-KCD-400-1- (C) 2005 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced

More information

PIX 535. PIX 535 Product Overview CHAPTER

PIX 535. PIX 535 Product Overview CHAPTER CHAPTER 7 PIX 535 This chapter describes the installation of the PIX 535, and includes the following sections: PIX 535 Product Overview Installing a PIX 535 PIX 535 Feature Licenses Installing Failover

More information

PIX 520. PIX 520 Product Overview CHAPTER

PIX 520. PIX 520 Product Overview CHAPTER CHAPTER 5 PIX 520 This chapter guides you through the installation of the PIX 520, and includes the following sections: PIX 520 Product Overview, page 5-1 Installing the PIX 520, page 5-4 PIX 520 Feature

More information

Installing the Cisco 2524 and Cisco 2525 Routers

Installing the Cisco 2524 and Cisco 2525 Routers CHAPTER 3 Installing the Cisco 2524 and Cisco 2525 Routers This chapter guides you through the installation of the Cisco 2524 and Cisco 2525 routers and includes the following sections: Required Tools

More information

BLACKBOX NETWORK SERVICES. one source for worldwide infrastructure services

BLACKBOX NETWORK SERVICES. one source for worldwide infrastructure services BLACKBOX NETWORK SERVICES one source for worldwide infrastructure services 24 Port 10/100Mbps plus 2 Gigabit TX/FX Auto-MDIX Modular Gigabit Ethernet Switch User s Manual FCC Warning This device has been

More information

PIX 515/515E. PIX 515/515E Product Overview CHAPTER

PIX 515/515E. PIX 515/515E Product Overview CHAPTER CHAPTER 4 PIX 515/515E This chapter describes how to install the PIX 515/515E, and includes the following sections: PIX 515/515E Product Overview Installing a PIX 515/515E PIX 515/515E Feature Licenses

More information

Installing the ASA 5550

Installing the ASA 5550 CHAPTER 3 Installing the ASA 5550 Caution Read the safety warnings in the Regulatory Compliance and Safety Information for the Cisco ASA 5500 Series and follow proper safety procedures when performing

More information

Installation and Configuration Guide

Installation and Configuration Guide Installation and Configuration Guide Trademark Notices Comtrol, NS-Link, and DeviceMaster are trademarks of Comtrol Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation.

More information

Perle SMI Media Converter Installation Guide

Perle SMI Media Converter Installation Guide Perle SMI Media Converter Installation Guide P/N 5500316-14 Overview This guide contains instructions necessary for the installation and operation of the Perle SMI Media Converter. This media converter

More information

Product Overview. Switch Models CHAPTER

Product Overview. Switch Models CHAPTER CHAPTER 1 The Cisco CGS 2520 switches, also referred to as the switch, are Ethernet switches that you can connect devices such as Intelligent Electronic Devices (IEDs), distributed controllers, substation

More information

Quick Start Guide. Gigabit Smart Switch Eco Fanless. Supports http and SNMP interfaces for switch management. LGB2118A LGB2124A

Quick Start Guide. Gigabit Smart Switch Eco Fanless. Supports http and SNMP interfaces for switch management. LGB2118A LGB2124A LGB2118A LGB2124A Gigabit Smart Switch Eco Fanless Quick Start Guide Supports http and SNMP interfaces for switch management. Customer Support Information Order toll-free in the U.S.: Call 877-877-BBOX

More information

Installing Power Modules

Installing Power Modules This chapter contains the procedures for installing cards and modules into the chassis after the chassis has been installed into a rack. This chapter also describes how to connect cables to RSP, RP, alarm,

More information

Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541 PoE Model: KSD-541-P. Installation Guide

Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541 PoE Model: KSD-541-P. Installation Guide Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports Basic Model: KSD-541 PoE Model: KSD-541-P Installation Guide DOC.080104-1- (C) 2008 KTI Networks Inc. All rights reserved.

More information

Installing and Removing SDRAM and DRAM

Installing and Removing SDRAM and DRAM CHAPTER 4 This chapter explains how to remove and replace the main memory modules on the network processing engine or network services engine. For the location of the memory module you are replacing, find

More information

Installing the Cisco SFS 3504 Server Switch

Installing the Cisco SFS 3504 Server Switch CHAPTER 3 This chapter describes how to mount your Cisco SFS 3504 Server Switch on a rack, boot the Cisco SFS 3504 Server Switch, and configure basic services. For advanced configuration information, see

More information

Industrial 5-Port Fast Ethernet Switches. with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541. PoE Model: KSD-541-HP. Installation Guide

Industrial 5-Port Fast Ethernet Switches. with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541. PoE Model: KSD-541-HP. Installation Guide Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports Basic Model: KSD-541 PoE Model: KSD-541-HP Installation Guide DOC.141201-1- (C) 2014 KTI Networks Inc. All rights reserved.

More information

4 10/100/1000T Mini-GBIC with 4 IEEE 802.3at High Power PoE Industrial Wide Temperature Switch. User Manual SISTP LRT

4 10/100/1000T Mini-GBIC with 4 IEEE 802.3at High Power PoE Industrial Wide Temperature Switch. User Manual SISTP LRT 4 10/100/1000T + 2 1000 Mini-GBIC with 4 IEEE 802.3at High Power PoE Industrial Wide Temperature Switch User Manual V1.0 September-2013 FCC Warning This Equipment has been tested and found to comply with

More information

Installing and Managing the Switch

Installing and Managing the Switch CHAPTER 2 This chapter describes how to install and manage the Cisco SFS 7008 system hardware and contains these sections: Safety, page 2-2 Preparing the Site, page 2-3 Rack-Mounting the Switch, page 2-4

More information

PHB-200M PHB x 100/1000Base-T to 20x 100/1000Base-X

PHB-200M PHB x 100/1000Base-T to 20x 100/1000Base-X SFP Patching Hub PHB-200M PHB-200 20x 100/1000Base-T to 20x 100/1000Base-X SFP Patching Hub PHB-200M is a 20-channel Managed SFP patching hub that converts copper 100/1000Base-TX to SFPs working at 100Mbps

More information

Installing and Upgrading Internal Modules and FRUs

Installing and Upgrading Internal Modules and FRUs Installing and Upgrading Internal Modules and FRUs, page 1 This document describes how to install and upgrade internal modules and field replaceable units (FRUs) in the Cisco 1100 Series Integrated Services

More information

D-Link Switch User Manual. Table of Contents

D-Link Switch User Manual. Table of Contents Table of Contents About This Guide... 1 Terms/Usage... 1 Copyright and Trademarks... 1 Product Introduction... 2 Package Contents... 2 Product Overview... 2 Front Panel... 2 Rear Panel... 2 Indicator LEDs...

More information

Omnitron Systems Technology, Inc. 1. iconverter. 19-Module Managed Power Chassis User s Manual

Omnitron Systems Technology, Inc. 1. iconverter. 19-Module Managed Power Chassis User s Manual Omnitron Systems Technology, Inc. 1 iconverter 19-Module Managed Power Chassis User s Manual 27 Mauchly, #201, Irvine, CA 92618 Phone: (949) 250-6510; Fax: (949) 250-6514 2 Omnitron Systems Technology,

More information

Perle IDS-108F(XT) Unmanaged 10/100 Ethernet Switches. Installation Guide. P/N (Rev G)

Perle IDS-108F(XT) Unmanaged 10/100 Ethernet Switches. Installation Guide. P/N (Rev G) Perle IDS-108F(XT) Unmanaged 10/100 Ethernet Switches Installation Guide P/N 5500339-10 (Rev G) Overview This document contains instructions necessary for the installation and operation of the Perle IDS-108F

More information

Chassis-based Media Converters

Chassis-based Media Converters Media Converters with Individual Metal Case Housing. DMC-615SC DMC-1002 Management Module DMC-1000 Chassis Chassis-based Media Converters System Overview The Chassis-based Media Converters include a number

More information

Power Supply and Fan Module Installation

Power Supply and Fan Module Installation 3 CHAPTER This chapter describes how to remove and install a new or replacement power supply or fan module in a Catalyst 3750-E or Catalyst 3560-E switch. See these sections: Installation Overview, page

More information

10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter. AMG9011G-H (-40 to 75C) User Manual

10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter. AMG9011G-H (-40 to 75C) User Manual 10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter AMG9011G-H (-40 to 75C) User Manual www.amgsystems.com Content Overview...1 Introduction... 1

More information

PHB-200M PHB x 100/1000Base-T to 20x 100/1000Base-X FE/GbE Media Converter Concentrator

PHB-200M PHB x 100/1000Base-T to 20x 100/1000Base-X FE/GbE Media Converter Concentrator Media Converter Concentrator PHB-200M PHB-200 20x 100/1000Base-T to 20x 100/1000Base-X FE/GbE Media Converter Concentrator PHB-200M is a 20-channel Managed Media Converter that converts copper 100/1000Base-TX

More information

24-Port 100/1000X SFP + 4-Port 10G SFP+ Managed. Metro Ethernet Switch MGSW-28240F. Quick Installation Guide

24-Port 100/1000X SFP + 4-Port 10G SFP+ Managed. Metro Ethernet Switch MGSW-28240F. Quick Installation Guide 24-Port 100/1000X SFP + 4-Port 10G SFP+ Managed Metro Ethernet Switch MGSW-28240F Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Requirements... 4 3. Wiring DC Power Inputs... 5

More information

ECS4620 Series 28/52-Port Layer 3 Stackable GE Switch Installation Guide

ECS4620 Series 28/52-Port Layer 3 Stackable GE Switch Installation Guide ECS460 Series 8/5-Port Layer 3 Stackable GE Switch Installation Guide www.edge-core.com Installation Guide ECS460-8T Stackable GE Switch ECS460-8T-DC Stackable GE Switch Layer 3 Stackable Gigabit Ethernet

More information

MS400870M. User's Guide. Ver.: Port GBE SFP Switch 19 1U 24x10/100/1000T Combo 10/1000X SFP

MS400870M. User's Guide. Ver.: Port GBE SFP Switch 19 1U 24x10/100/1000T Combo 10/1000X SFP MS400870M 24 Port GBE SFP Switch 19 1U 24x10/100/1000T Combo 10/1000X SFP User's Guide. Ver.:0.91 1 CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference

More information

GigaVUE-2404 // Data Sheet

GigaVUE-2404 // Data Sheet Mgmt Console M/S Rdy 10/100/1000 PORTS (SFP) G1 G2 G3 G4 G1 G2 G3 G4 1 1 2 2 3 3 4 5 4 5 6 6 7 7 8 8 SLOT 2 PORTS 9 16 SLOT 1 PORTS G1-G4 PORTS 1-8 SLOT 3 PORTS 17 24 PS ALARM CUTOFF UP WHEN INSTALLED

More information

Product Overview. Features CHAPTER

Product Overview. Features CHAPTER CHAPTER 1 The Catalyst 3750 Metro switch, also referred to as the switch, is a stackable metro Ethernet switch that can be used as customer-located equipment (CLE) to connect to enterprise customer routers

More information

Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any

More information

H3C SecPath M9000-S NSQM2MPUD0 main processing unit

H3C SecPath M9000-S NSQM2MPUD0 main processing unit H3C SecPath M9000-S NSQM2MPUD0 main processing unit 1 Identifier The module identifier NSQM2MPUD0 is at the upper right corner of the front panel. 2 The NSQM2MPUD0 MPU has a console port, a USB port, a

More information

Overview. Features CHAPTER

Overview. Features CHAPTER CHAPTER 2 This chapter provides these topics that describe the Catalyst 2955 switch, hereafter referred to as the switch. Features, page 2-1 Front-Panel Description, page 2-3 Rear-Panel Description, page

More information

Junos WebApp Secure 5.0 Hardware Guide

Junos WebApp Secure 5.0 Hardware Guide Junos WebApp Secure 5.0 Hardware Guide Junos WebApp Secure 5.0 Hardware Guide This document contains a specification for the MWS1000 hardware appliance, as well as instructions for installation into a

More information

10/28/52-Port Web-Smart Pro Gigabit Ethernet Switch 26-Port Web-Smart Pro 10G Ethernet Switch. Installation Guide.

10/28/52-Port Web-Smart Pro Gigabit Ethernet Switch 26-Port Web-Smart Pro 10G Ethernet Switch. Installation Guide. 0/8/5-Port Web-Smart Pro Gigabit Ethernet Switch 6-Port Web-Smart Pro 0G Ethernet Switch Installation Guide www.edge-core.com Installation Guide ECS00-0T Gigabit Ethernet Switch Web-Smart Pro Gigabit Ethernet

More information

Connecting and Routing the Cables and Wires

Connecting and Routing the Cables and Wires This chapter explains how to install the NCS 2002 shelf. The sections are: NTP-L36 Attaching Wires to Timing, LAN, and Craft Pin Connections in NCS 2002, on page 1 NTP-L36 Attaching Wires to Timing, LAN,

More information

Gigabit Ethernet Switch With 10G Uplinks. Hardware Manual MS400860M

Gigabit Ethernet Switch With 10G Uplinks. Hardware Manual MS400860M Gigabit Ethernet Switch With 10G Uplinks Hardware Manual MS400860M Gigabit Ethernet Switch with 10G Uplinks Hardware Manual II About This Guide Purpose Audience Conventions This guide details the hardware

More information

PHB-200M/PHB x 100/1000Base-T to 20x100/1000Base-X SFP Patching Hub

PHB-200M/PHB x 100/1000Base-T to 20x100/1000Base-X SFP Patching Hub SFP Patching Hub PHB-200M/PHB-200 20x 100/1000Base-T to 20x100/1000Base-X SFP Patching Hub PHB-200M is a 20-channel Managed SFP patching hub that converts copper 100/1000Base-TX to SFPs working at 100Mbps

More information

Numerics INDEX. cables caution 1-19 cabling

Numerics INDEX. cables caution 1-19 cabling INDEX Numerics 10/100/1000 PoE ports numbering 1-3, 1-4 pinouts B-2 recommended cables 2-25 10/100/1000 ports cabling 1-6 connecting to 2-26 numbering 1-2 overview 1-6 10/100 and 10/100/1000 PoE+ Port

More information

PHB-200M PHB x 100/1000Base-T to 20x100/1000Base-X SFP Patching Hub

PHB-200M PHB x 100/1000Base-T to 20x100/1000Base-X SFP Patching Hub SFP Patching Hub PHB-200M PHB-200 20x 100/1000Base-T to 20x100/1000Base-X SFP Patching Hub PHB-200M is a 20-channel Managed SFP patching hub that converts copper 100/1000Base-TX to SFPs working at 100Mbps

More information

See instructions to download and install the latest version of LinkBoxMB and the user's manual at

See instructions to download and install the latest version of LinkBoxMB and the user's manual at Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any

More information

BV-10 Performance Endpoint Unit PERFORMANCE DEMARCATION FOR NETWORK-WIDE VISIBILITY

BV-10 Performance Endpoint Unit PERFORMANCE DEMARCATION FOR NETWORK-WIDE VISIBILITY PERFORMANCE DEMARCATION FOR NETWORK-WIDE VISIBILITY Highly cost-effective Ethernet performance monitoring device providing complete network visibility for mobile backhaul, Carrier Ethernet and PTN networks

More information

Installing the Cisco AS5400XM Universal Gateway

Installing the Cisco AS5400XM Universal Gateway CHAPTER 3 Installing the Cisco AS5400XM Universal Gateway This chapter guides you through the installation of the Cisco AS5400XM universal gateway and includes the following sections: Setting Up the Chassis,

More information

Industrial 24-Port 10/100/1000Mbps Managed Gigabit. Switch (-40~75 degrees C) with 4 Shared SFP Ports IGSW-24040T. Quick Installation Guide

Industrial 24-Port 10/100/1000Mbps Managed Gigabit. Switch (-40~75 degrees C) with 4 Shared SFP Ports IGSW-24040T. Quick Installation Guide Industrial 24-Port 10/100/1000Mbps Managed Gigabit Switch (-40~75 degrees C) with 4 Shared SFP Ports IGSW-24040T Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Requirements... 4

More information

Installation User Manual

Installation User Manual EPON OLT EPON Optical Line Terminal Equipment Installation User Manual V.1.3 Contents 1 PRODUCT INTRODUCTION... 2 1.1 BRIEF INTRODUCTION... 2 1.2 FUNCTIONAL FEATURES... 2 1.3 APPEARANCE AND INTERFACE...

More information

M5 and M10 Routers Power Supply and Power Cord Component Replacement Instructions

M5 and M10 Routers Power Supply and Power Cord Component Replacement Instructions M5 and M10 Routers Power Supply and Power Cord Component Replacement Instructions Part No. 530-003244-01 Revision 1 27 July 2000 This document describes how to remove and replace the AC and DC power supplies,

More information

TRC-190 User s Manual

TRC-190 User s Manual First Edition, November 2008 www.moxa.com/product 2008 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. The software described in this manual is furnished under a license agreement

More information

Switched Uplink Modules

Switched Uplink Modules APPENDIX D Switched Uplink Modules When installed in a FastHub 400 model, each 10BaseT/100BaseTX and 100BaseFX switched uplink module provides a separate switched collision domain for traffic to the workgroup

More information

Installing a Network Module

Installing a Network Module Network Module Overview, page in the Switch, page 7 Removing a Network Module, page 3 SFP and SFP+ Modules, page 4 Finding the Network Module Serial Number, page 6 Network Module Overview Network Module

More information

Product Overview. Switch Model

Product Overview. Switch Model Switch Models The Catalyst 3850 family of switches are Ethernet switches to which you can connect devices such as Cisco IP Phones, Cisco Wireless Access Points, workstations, and other network devices

More information

Perle SMI Media Converter Installation Guide

Perle SMI Media Converter Installation Guide Perle SMI Media Converter Installation Guide P/N 5500316-10 Introduction Perle SMI Media Converters provide seamless high-speed managed integration of Ethernet to Fiber networks. Overview This guide contains

More information

Product Overview. Switch Descriptions. Front Panel CHAPTER

Product Overview. Switch Descriptions. Front Panel CHAPTER CHAPTER 1 The Catalyst 2360 switch, also referred to as the switch, is an Ethernet switch to which you can connect devices such as servers, routers, and other switches. Switch Description, page 1-1 Front

More information

SFP GIGABIT MANAGED SWITCH ECO

SFP GIGABIT MANAGED SWITCH ECO QUICK INSTALLATI GUIDE LGB5124A-R2, LGB5128A-R2 SFP GIGABIT MANAGED SWITCH ECO 24/7 AT OR VISIT BLACKBOX.COM + + RTN + -48V RST PWR AC PWR DC SYS ALM CSOLE 28-PORT GbE MANAGED SWITCH AC INPUT: 100-240

More information

The interface ports are selectively enabled based on their functions in the system management versus non-management.

The interface ports are selectively enabled based on their functions in the system management versus non-management. This chapter describes how to cable the interface ports on Management I/O (MIO) or Management I/O Universal (UMIO) cards. It includes the following sections: Interface Ports, page Port Status LEDs, page

More information

TRC-190 User s Manual

TRC-190 User s Manual User s Manual Edition 3.2, May 2017 www.moxa.com/product 2017 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used only

More information

KOM600/KOM600G Fiber Media Converter Hardware Installation Manual

KOM600/KOM600G Fiber Media Converter Hardware Installation Manual KOM600/KOM600G Fiber Media Converter Hardware Installation Manual Kyland Technology Co., LTD. Publication Date: Dec. 2012 Version: V1.1 Customer Service Hotline: (+8610) 88796676 FAX: (+8610) 88796678

More information

Next Generation Firewall

Next Generation Firewall Next Generation Firewall Hardware Guide Models 1101, 1105, 2101, 2105 Revision D Contents Introduction on page 2 Find product documentation on page 2 Series 1100 features on page 3 Series 2100 features

More information

Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any

More information

Nortel Secure Router 2330/4134 Installation Hardware Components. Release: 10.2 Document Revision:

Nortel Secure Router 2330/4134 Installation Hardware Components. Release: 10.2 Document Revision: Installation Hardware Components Release: 10.2 Document Revision: 03.01 www.nortel.com NN47263-301. . Release: 10.2 Publication: NN47263-301 Document release date: 7 September 2009 While the information

More information

User Manual Entry Line Industrial Fast Ethernet Switch 5x 10/100Base-TX

User Manual Entry Line Industrial Fast Ethernet Switch 5x 10/100Base-TX User Manual Entry Line Industrial Fast Ethernet Switch 5x 10/100Base-TX Entry Line Fast Ethernet Switch Fast Ethernet Switch for Industrial Use Page 2/11 Table of Contents General... 3 Benefits... 3 Front

More information

Hypercable injecteur HPOE - Industrial IEEE 802.3at Gigabit PoE Injector. User Manual. v.1.0 Jun Mail :

Hypercable injecteur HPOE -  Industrial IEEE 802.3at Gigabit PoE Injector. User Manual. v.1.0 Jun Mail : Industrial IEEE 802.3at Gigabit PoE Injector User Manual v.1.0 Jun-2011 FCC Warning This Equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

More information

SWH-3112 Series 12-port L2+ Managed Gigabit Fiber Switch User s Guide

SWH-3112 Series 12-port L2+ Managed Gigabit Fiber Switch User s Guide SWH-3112 Series 12-port L2+ Managed Gigabit Fiber Switch User s Guide Version: 1.0 Revision History Version Date Changes 0.9 11/10/2017 First release 1.0 05/08/2018 Use the new template FCC Warning This

More information

9. NTP-C11 Remove and Replace an Ethernet Card, page 1-13 As needed, complete this procedure to remove and replace an ONS CL Ethernet card.

9. NTP-C11 Remove and Replace an Ethernet Card, page 1-13 As needed, complete this procedure to remove and replace an ONS CL Ethernet card. CHAPTER 1 This chapter provides procedures for installing the Cisco ONS 15310-CL shelf, cards, and fiber-optic cable. To view a summary of the tools and equipment required for installation, see the Required

More information

MF BASE-T to 1000BASE-X INDUSTRIAL MEDIA CONVERTER WITH SFP SUPPORT INSTALLATION GUIDE

MF BASE-T to 1000BASE-X INDUSTRIAL MEDIA CONVERTER WITH SFP SUPPORT INSTALLATION GUIDE 1000BASE-T to 1000BASE-X INDUSTRIAL MEDIA CONVERTER WITH SFP SUPPORT INSTALLATION GUIDE September 2006 VERSITRON, Inc. 83 Albe Drive - Suite C Newark, DE 19702 2 PROPRIETARY DATA All data in this manual

More information

Installation Guide 24-port 10/100 Fast Ethernet Switch with 1 Fiber Connection Model Name: KS-324F

Installation Guide 24-port 10/100 Fast Ethernet Switch with 1 Fiber Connection Model Name: KS-324F Installation Guide 24-port 10/100 Fast Ethernet Switch with 1 Fiber Connection Model Name: KS-324F We make no warranties with respect to this documentation and disclaim any implied warranties of merchantability,

More information

8-Port 10/100Mbps + 2G TP/SFP Combo. Managed Industrial Switch ISW-1022M / ISW-1022MT / ISW-1022MP / ISW-1022MPT / ISW-1033MT

8-Port 10/100Mbps + 2G TP/SFP Combo. Managed Industrial Switch ISW-1022M / ISW-1022MT / ISW-1022MP / ISW-1022MPT / ISW-1033MT 8-Port 10/100Mbps + 2G TP/SFP Combo Managed Industrial Switch ISW-1022M / ISW-1022MT / ISW-1022MP / ISW-1022MPT / ISW-1033MT Quick Installation Guide Table of Contents 1. Package Content... 3 2. Requirements...

More information

See instructions to download and install the latest version of LinkBoxEIB and the user's manual at

See instructions to download and install the latest version of LinkBoxEIB and the user's manual at Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any

More information

See instructions to download and install the latest version of LinkBoxMB and the user's manual at

See instructions to download and install the latest version of LinkBoxMB and the user's manual at Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any

More information

LNP-0602 series. 6-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 2*100Fx. User Manual

LNP-0602 series. 6-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 2*100Fx. User Manual LNP-0602 series 6-port Industrial PoE+ Unmanaged Ethernet Switches 4*10/100Tx (30W/Port) + 2*100Fx User Manual FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A

More information

Replacing the Power Supply

Replacing the Power Supply APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools

More information

16-Port Chassis Media Converter System Manual

16-Port Chassis Media Converter System Manual 16-Port Chassis Media Converter System Manual 17732-B 16-Port Media Converter (ST Connectors, Shown) INTRODUCTION This system manual describes the ADC 16-Port Media Converter with SC and ST connectors,

More information

Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2

Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2 Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2 Cisco CRS 3-Phase AC Power Distribution Unit 2 Revised: November 18, 2016,

More information

Introduction. Overview

Introduction. Overview The Cisco ubr Advanced RF Switch (Cisco UBR-RFSW-ADV) provides N+ line card redundancy switching for the Cisco ubr00 universal broadband router also known as the Cisco CMTS. The Cisco UBR-RFSW-ADV is a

More information

Fast Ethernet Converter. User Guide MICROSENS

Fast Ethernet Converter. User Guide MICROSENS Fast Ethernet Converter User Guide MICROSENS Rev.1.25 Jan-2010 Content Introduce... 1 Features... 2 Package Contents... 3 Hardware Description... 4 Front Panel... 4 Ports... 5 LED Indicators... 5 DIP-switch...

More information

Catalyst 2960-X and 2960-XR Switch Hardware Guide

Catalyst 2960-X and 2960-XR Switch Hardware Guide 2960-X and 2960-XR Switch Hardware Guide The 2960-X and 2960-XRfamily of switches are Ethernet switches to which you can connect devices such as Cisco IP Phones, Cisco Wireless Access Points, workstations,

More information

Optimux-34 Fiber Optic Multiplexer

Optimux-34 Fiber Optic Multiplexer Data Sheet Optimux-34 Multiple E1, Ethernet, or High-speed Data over E3 or Fiber, up to 110 km (68 miles) Up to 16 E1 links, high-speed data, and Ethernet traffic multiplexed into one E3 copper or fiber

More information

8-port 10/100TX + 2-Port 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Ethernet Switch User Manual

8-port 10/100TX + 2-Port 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Ethernet Switch User Manual 8-port 10/100TX + 2-Port 10/100/1000T/100/1000 SFP Combo with 8 PoE Injectors Industrial Ethernet Switch User Manual FCC Warning This Equipment has been tested and found to comply with the limits for a

More information

1 10/100TX FX w/ 1 PoE Injector Industrial Switch. User Manual

1 10/100TX FX w/ 1 PoE Injector Industrial Switch. User Manual 1 10/100TX + 1 100FX w/ 1 PoE Injector Industrial Switch User Manual CE Mark Warning This is a Class-A product. In a domestic environment this product may cause radio interference in which case the user

More information

Optimux-34, Optimux-25

Optimux-34, Optimux-25 Data Sheet Optimux-34, Optimux-25 16-Channel E1/T1, Ethernet or Data over E3 or Fiber Multiplexers Up to 16 E1/T1 links and high-speed data or Ethernet traffic multiplexed into fiber opt7ic uplink E3 copper

More information

PoE Powered Gigabit Ethernet Media Converters 1000BASE-T TO 1000BASE-SX/LX. KGC-352 Series. Installation Guide

PoE Powered Gigabit Ethernet Media Converters 1000BASE-T TO 1000BASE-SX/LX. KGC-352 Series. Installation Guide PoE Powered Gigabit Ethernet Media Converters 1000BASE-T TO 1000BASE-SX/LX KGC-352 Series Installation Guide DOC.070820-KGC-352-1- (C) 2007 KTI Networks Inc. All rights reserved. No part of this documentation

More information

ChromaFlex Chassis. Hardware Interface Manual

ChromaFlex Chassis. Hardware Interface Manual ChromaFlex Chassis Hardware Interface Manual Although every effort has been taken to ensure the accuracy of this document it may be necessary, without notice, to make amendments or correct omissions. Specifications

More information

Installation Job Aid for VSP 4850GTS

Installation Job Aid for VSP 4850GTS Installation Job Aid for VSP 4850GTS Notices Release 6.1.0.0 NN46251-308 Issue 02.01 November 2017 Notice paragraphs alert you about issues that require your attention. The following paragraphs describe

More information

10/100TX to 100FX w/ 1 PoE Injector Industrial Media Converter User Manual

10/100TX to 100FX w/ 1 PoE Injector Industrial Media Converter User Manual 10/100TX to 100FX w/ 1 PoE Injector Industrial Media Converter User Manual v1.02 FCC Warning This Equipment has been tested and found to comply with the limits for a Class-A digital device, pursuant to

More information

Installation and Configuration Quick Guide. R3000 Lite. Industrial Dual SIM Cellular VPN Router (1 Eth + 1 RS RS USB Host)

Installation and Configuration Quick Guide. R3000 Lite. Industrial Dual SIM Cellular VPN Router (1 Eth + 1 RS RS USB Host) Package Contents Before installing your R3000 Lite Router, please verify the kit contents as following. 1 x Robustel R3000 Lite Industrial Dual SIM Cellular VPN Router 1 x 3-pin pluggable terminal block

More information

Media Conversion. Extend Network Distance via Fiber Optic

Media Conversion. Extend Network Distance via Fiber Optic Media Conversion Extend Network Distance via Fiber Optic Contents Managed Media Converter Chassis Model MC-1610MR MC-1610MR48 Media Converter Chassis Managed Standard Media Converters Smart Converters

More information

ROCKETLINX ES8508 ES8508 ES8508F ES8508-XT ES8508F-XT QUICK INSTALLATION GUIDE

ROCKETLINX ES8508 ES8508 ES8508F ES8508-XT ES8508F-XT QUICK INSTALLATION GUIDE ROCKETLINX ES8508 ES8508 ES8508F ES8508-XT ES8508F-XT QUICK INSTALLATION GUIDE 2000577 Rev B Release Date - September, 2013 INTRODUCTION The RocketLinx ES8508 series features advanced Layer 2 management

More information

IMC-21GA Quick Installation Guide

IMC-21GA Quick Installation Guide IMC-21GA Quick Installation Guide Moxa Industrial Media Converter Edition 4.0, June 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

See instructions to download and install the latest version of LinkBoxMB and the user's manual at

See instructions to download and install the latest version of LinkBoxMB and the user's manual at Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any

More information

General. 5 and 8 port Fast Ethernet switches. 6 and 8 Port Gigabit Ethernet switches. Switches with fiber uplink

General. 5 and 8 port Fast Ethernet switches. 6 and 8 Port Gigabit Ethernet switches. Switches with fiber uplink Entry Line Industrial Gigabit Ethernet Switch 4x 10/100/1000Base-T with PoE+, 1x 10/100/1000Base-T or 100/1000Base-X Combo Port, 1x 100/1000Base X SFP Slot General The IP protocol has already left the

More information

Remote RMM-1400 Intelligent Remote Site Management Device. Installation Guide

Remote RMM-1400 Intelligent Remote Site Management Device. Installation Guide Remote RMM-1400 Intelligent Remote Site Management Device Guide INSTALLATION GUIDE Westell Technologies Part # 030-300645 Rev. A Copyright 2015 by Westell Technologies. All Rights Reserved. Westell, Kentrox

More information