LM961 Bluetooth Dual Mode Module

Transcription

1 Bluetooth ual Mode Module 15/EC/2016 Revised 2.55mm 18.9mm 12.71mm Features Bluetooth ual Mode (Bluetooth v2.0, v2.1 and Bluetooth v4.0) Requires no external hardware Class 1 x Out Power I2C, UAR and USB 2.0 (Full Speed) Low Power Consumption IC Antenna Onboard Serial Port Profile (SPP) Individual PWM channels (3 on dedicated LE pads) 6 digital and 3 analogue 18.9mm x 12.71mm X 2.55mm SM Side and Bottom Pads for easy production Application firmware support RoHS, REACH and WE Compliant Solution Programmable Standalone Module (With Embedded Bluetooth v4.1 Stack) Includes UAR to SPP Bridge Application Overview he Bluetooth ual Mode module is a powerful, versatile and cost effective solution designed for use as a GAP Central (master) or GAP Peripheral device. his allows your embedded system to wirelessly communicate with other nearby Bluetooth v2.0, v2.1 and Bluetooth v4.0 enabled devices (e.g. ios and Android). he is also ideal for streaming high quality data and establishing Bluetooth Low Energy connections. his single core standalone module combines a Bluetooth low energy and v2.0, v2.1 radio using a dual mode Bluetooth v4.1 stack, plus a microcontroller unit with an 8 Mbit flash memory for running the application. It also incorporates 29 pin outs, including I2C, UAR and USB for interfacing with sensors and many other peripheral devices. It s SM side and bottom pads allow for easy manufacture and placement within your product. LM offer bespoke integration into your product by supporting your developer, including development of new applications for the module. We also offer Bluetooth ual Mode demo applications, which can be customised to your specification. he module can be used as a bridge between Bluetooth v2.0, v2.1 and Bluetooth v4.0 devices, using our SPP to UAR Bridge Application. eveloped firmware and configuration settings can be preloaded to the module before supply. Page 1 of 15

2 Bluetooth ual Mode Module General Specification v4.1 (ual Mode) Module ype Standalone (Configurable with A Commands) Profiles SPP Bluetooth Standard Wireless Chipset Antenna Microcontroller (MCU) Flash Memory M Program Interface Interfaces Power Supply Crystal Oscillators evelopment Kit RF Characteristics CSR IC Antenna Onboard 80 MHz RISC MCU 8 Mbit 56 KB (12K x 24-bit) SPI I2C, UAR, USB 2.0 (Full Speed), AIO, PIO and PWM 5V (VCHG/ VBUS) or 2V8 (VBA) 26 MHz LM55X 9.4 dbm (Bluetooth v2.0, v.2.1) and 10 dbm (Bluetooth v4.0) x Output Power Hardware Rx Sensitivity -87 dbm (Bluetooth v2.0, v.2.1) and -92 dbm (Bluetooth v4.0) ata Rate Up to 3Mbps Frequency 2.4 GHz to GHz Physical Characteristics Operating emperature -40 C to +85 C imensions (L x W x H) 18.9mm x 12.71mm x 2.55mm Weight 0.84 g Certifications SIG Compliance RoHS, REACH and WE Page 2 of 15

3 Bluetooth ual Mode Module Firmware he Bluetooth ual Mode module is configured by using A commands in configuration mode. he A command set controls the primary operations such as information enquiry, connection/ disconnection set up and settings. he module is configured via its UAR interface from a microcontroller or PC, using a MCU software or Hercules SEUP utility respectively. At the start of every power up cycle the enters the configuration mode. Please refer to the A Commands user manuals for the BR/ER and Bluetooth low energy connection configurations details: A Commands Manual BR / ER - A Commands Manual Bluetooth low energy connections - efault Factory Settings evice Settings iscoverable : YES evice Name: _PROO_01 Echo of command: YES Response to commands: YES efault Security mode 2.1 Bluetooth Classic Profile Settings UAR Settings Baud rate : Stop bit : ONE Parity bits: NONE Flow Control: None Bluetooth Low Energy Settings GAP Role: Central GA ROLE: Client SPP Role : SLAVE Escape sequence check enabled: YES A commands are used to establish BR / ER and Bluetooth low energy connections. In data mode, data can be transmitted and received between the Bluetooth Classic and Bluetooth v4.0 devices via the (Bluetooth ual Mode Module). By using our SPP to UAR Bridge application. And the UAR interface represents the data channel once a connection is established. o break the connection and enter the configuration mode again, the has to be powered off. SSP 2.1 Settings IoypesSupported : io capability keyboard only ForceManInheMiddle : RUE ynamicpinenb: RUE, Page 3 of 15

4 Bluetooth ual Mode Module Bluetooth Applications he module can run full application code for a wide range of industries. his includes the automotive, M2M (industrial cable replacement), EPOS, health & fitness and consumer electronics (e.g. printers and wearable technologies) industries. Only limited by the imagination of the embedded developer. he modules can run all Bluetooth applications. epending on whether the embedded developer requires a low energy Bluetooth connection, a high-quality data stream Bluetooth connection or both simultaneously. LM echnologies offer both Bluetooth v4.0 and Bluetooth Classic application support. his includes assisting the developer and creating new applications with the modules: Alert ag Security ag Key Fob Beacon Blood Pressure Sensor Cycling Speed and Cadence Sensor Environment Sensor Health hermometer Heart Rate Sensor Serial Communication Keyboard ime Client Multifunction Steering Wheel emperature and Pressure Mouse Weight Scale Printer Glucose Sensor Running Speed and Cadence Sensor Example Applicaiton LM SPP to UAR Bridge Application he module can act as a bridge between a Bluetooth Classic device and a Bluetooth v4.0 device. By using our Bluetooth ual Mode application SPP to UAR Bridge. Allowing Bluetooth Classic data to be transmitted to a Bluetooth v4.0 device through the or vice versa User Application SPP RFCOMM User Application GAP X GA SMP A L2CAP L2CAP Link Manager Link Layer BR/ER PHY LE PHY CONNECION A LM048 CONNECION B LM931 UAR over GA: Bluetooth data to a Bluetooth v4.0 device, for example our LM931 UAR over SPP: Bluetooth data to a Bluetooth v2.0 or v2.1 device, for example our LM048 Page 4 of 15

5 Bluetooth ual Mode Module he SPP to UAR Bridge application flow diagram below outlines the steps to setup the bridge : Connect to Bluetooth v2.0, v2.1 device with SPP profile (Master or Slave) Start Connection A enters in Configuration Mode Search Bluetooth low energy devices Connect with Bluetooth low energy device scans the services on Bluetooth low energy device Connection B scans service for Serial over GA characteristics detects Serial Service writes serial CCFG flag and SPP characteristics Set the device in SPPMOE receives data from Bluetooth low energy/v2.0, v2.1 device & transmits to v2.0, v2.1/bluetooth low energy device isconnect Bluetooth v2.0, v2.1 connection isconnect Bluetooth low energy device connection Stop Note 1. Connection A and Connection B sequence can be interchanged. 2. After Connection A, the device must be in Configuration Mode. 3. he must enable the Serial CCFG flag on the Bluetooth low energy Peripheral to transmit data. 4. No specific order is required for disconnection. Page 5 of 15

6 Bluetooth ual Mode Module Powering he can be powered in one of 2 ways: 29 1) Powered through the VCHG/VBUS (Pin 21) 2) Powered from a Lithium ion / Lithium polymer battery through VBA (Pin 19) PIN 1 10 Pin Outs GN GN AIO_0 LE_0 AIO_1 LE_1 AIO_2 LE_2 RS USB_P PIO_0 / SCL USB_N GN VBA_SENSE PIO_1 / S CHG_EX Page 6 of 15 VBA SPI_MOSI SPI_CLK SPI_ENABLE GN SPI_CS VREGENABLE SPI_MISO PIO_3 / UAR_X PIO_5 / UAR_CS VCHG / VBUS PIO_4 / UAR_RS PIO_2 / UAR_RX

7 Bluetooth ual Mode Module Pin Assignments ype escription ypical 1 GN Ground Common Ground 0V 2 AIO_0 Input Analog Input 3 AIO_1 Input Analog Input 4 AIO_2 Input Analog Input 5 RS Input 6 PIO_0 / SCL 7 GN Ground 8 PIO_1 / S 9 PIO_2 / UAR_RX 10 PIO_3 / UAR_X 11 PIO_4 / UAR_RS 12 PIO_5 / UAR_CS 13 SPI_MISO Pin Name Programmable Input / Output or I2C Serial Clock Common Ground 0V Programmable Input / Output or I2C Serial ata Programmable Input / Output or UAR Receive Programmable Input / Output or UAR ransmit Programmable Input / Output or UAR RS Programmable Input / Output or UAR CS SPI Master In Slave Out Reset 14 SPI_CS SPI Chip Select 15 GN Ground Common Ground 0V 16 SPI_ENABLE SPI Enable (CSR) 17 SPI_CLK SPI Clock 18 SPI_MOSI SPI Master Out Slave In 19 VBA Power Battery input 2V8 20 VREGENABLE Power Voltage Regulator Enable 1V 21 Power Battery Charger Input/ Positive Power Supply 5V (3V - 6.5V) 22 CHG_EX Power External Battery Charge Control 0V - 6.5V & 0mA-20mA 23 VBA_SENSE Power Battery Charger Sense Input 200mV (195mV - 205mV) 24 USB_N USB Negative 25 USB_P USB Positive 26 LE_2 Output PWM / LE 2 27 LE_1 Output PWM / LE 1 28 LE_0 Output PWM / LE 0 29 GN Ground Common Ground 0V VCHG / VBUS Page 7 of 15

8 Bluetooth ual Mode Module Module Block iagram AIO Filter B_RF CSR Chipset PWM VCHG / VBA AN SPI (ebug) UAR/PIO I2 C FLA 8 Mbit SIO USB XL 26MHz Page 8 of 15

9 Bluetooth ual Mode Module op View Pin Physical imensions mm 11.5mm 12.71mm 1.27 Pin Spacing 1.27 Pin mm mm 18.90mm Front View 2.1mm 2.55mm 0.8mm mm 18.90mm Side View 2.1mm 2.55mm 0.8mm 1.21mm 4.41mm 12.71mm Page 9 of 15

10 Bluetooth ual Mode Module PCB Footprint EGE OF HOS PCB ( Optimal ) Optimal Placement Position Pin 1 Placement Note If the optimal placement position cannot be achieved, ensure there is no metal beneath the highlighted part of module. 3.81mm 7.87mm 12.71mm NB Aim to place the module away from interference. (i.e: place the module at the edge of the board.) NO MEL BENEAH HIS AREA Pin Pin Spacing Pin mm 1.0mm mm 18.90mm Page 10 of 15

11 Bluetooth ual Mode Module Soldering and Reflow Chart Page 11 of 15

12 Bluetooth ual Mode Module ape and Reel Packaging 0.15mm 4mm 32mm mm ape imensions 0.32mm 13.8mm 3mm Reel imensions 330mm Notes Carton imensions (L x W x H): 360mm x 290mm x 370mm Quantities 1000 modules per ape 4 Boxes per Carton 4000 modules per Carton 36mm 92mm Page 12 of 15

13 Bluetooth ual Mode Module ray Packaging ray imensions LM951 6 X 10 10mm 8.7mm 5mm 6.3mm 143mm 312mm 13.4mm 47.4mm Notes Quantities Anti-Static PS ray, Black. 60 modules per ray Electrical Resistance: 1 MΩ< R< 100MΩ. 600 modules per Box hickness: = 0.8 mm 4 Boxes per Carton Carton imensions (L x W x H): 2400 modules per Carton 360mm x 325mm x 160mm Page 13 of 15

14 Bluetooth ual Mode Module Packaging for ape & Reel / ray he trays/reels are stacked and inserted into an anti-static vacuum bag and the Anti-Static Label, Model Name Label and Moisture Sensitive Labels stuck on. Reels are place within a vacuum bag. drying agent Humidity Indicator Card Anti-static aluminium vacuum bag. rays are stacked up with an empty tray on the top. he vacuum bag is placed inside the box and a Model Name Label stuck on the front-side of each box. Model name label Anti-static aluminium vacuum bag. b ox box ) carton carton label Each carton contains 4 boxes. Page 14 of 15

15 Bluetooth ual Mode Module Module 1 x SM Plug & Play IC Ant Module ape & Reel Module 1 x SM Plug & Play IC Ant Module ray Packaging Options Page 15 of 15