Contents. P.3 Accessory Box. P.8 P.9 Fan Installation System Ready Optional: Additional Fan & Liquid Cooling Radiator

Transcription

1 VIPER

2 Contents Product Overview Disassembling Chart P.2 Top I/O P.3 Accessory Box P.4 Installation Guide Open Chassis P.5 Install Power Supply P.5 Install Motherboard P.6 Install Add-in Card P.7 Install External 5.25" Device Install 3.5 /2.5 HDD/SSD P.8 P.9 Fan Installation System Ready Optional: Additional Fan & Liquid Cooling Radiator P.9 P.9 P.10 Thank you for purchasing a High-Quality Rosewill Product. Please register your product at : for complete warranty information and future support for your product. If you have any questions while using our products, please visit our website : for latest driver & user manual. Support Phone Number: Support techsupport@rosewill.com 1 All rights reserved by Rosewill

3 Disassembling Chart ( Components vary by country ) Right Side Panel Top Panel Front Panel Left side panel HDD Tray Front I/O Cable Pinout ( Please refer to your motherboard s user manual to connect. ) USB 3.0 CONNECTOR Card Reader CONNECTOR USB+5V LP- LP+ GND USB+5V LP- LP+ GND NC PIN PIN USB2.0 CONNECTOR HD Audio CONNECTOR USB+5V USB+5V AUD GND PORT1L LP LP PRESENCE# PORT1R LP+ LP+ SENSE1 RETURN PORT2R GND GND NO PIN SENSE SEND NC NO PIN SENSE2 RETURN PORT2L NO PIN NO PIN 2 All rights reserved by Rosewill

4 Top I/O USB 2.0 USB to M/B USB 3.0 TO PSU TO FAN to M/B Card Reader Card Reader connector Card Reader Card Reader connector to M/B USB TF SD USB USB USB H S L Power Button to M/B POWER SW Audio HD AUDIO connector HD AUDIO connector to M/B (1 Audio Connection per M/B, please check HD Audio) Reset Button Reset SW to M/B 3 All rights reserved by Rosewill

5 Accessory Box Figure Part s Name Function 16x Screw-A 2.5 HDD SSD 16x Screw-B 3.5 /5.25 ODD 3x M/B Standoff Motherboard 19x Screw-C PSU + M/B 1x M/B Sleeve M/B Standoff 1x PC Buzzer Motherboard 2x Cable Tie Cables 1x Side Panel Lock Side Panel 1x Screw-D Side Panel Lock 4 All rights reserved by Rosewill

6 Installation Guide 1. Open Chassis 1-1 Remove the 2 thumbscrews on each panel and slide them out. 2. Install Power Supply 2-1 Rest the power supply unit on the bottom of the case and secure it down with screw-c. If the PSU is equipped with single fan, you may have two options of installation: - Fan Facing Upwards: No special requirements. - Fan Facing Downwards: Make sure that there is enough room for air-intake between the bottom of case and the surface where the case is located. - Clean the dust filter regularly to ensure adequate airflow. 5 All rights reserved by Rosewill

7 CASE VIPER Z 3. Install Motherboard 3-1 Place the motherboard standoffs based on the form factor. 3-2 Secure the motherboard with screw-c. 6 All rights reserved by Rosewill

8 4. Install Add-in Card 4-1 Unscrew to remove the slot cover. 4-2 Install the add-in card. 4-3 Secure with screw. 7 All rights reserved by Rosewill

9 5. Install External 5.25 device 5-1 Pull the front panel outwards and detach. Remove the bay cover Insert the 5.25 drive into the bay and secure with screw-b. - Unscrew to retrieve the 3.5 adaptor. - Rest the 3.5 deice onto the adaptor and secure it down with screws. - Install the adaptor back into the bay. - Reinstall the front panel back onto the case. 8 All rights reserved by Rosewill

10 6. Install 3.5 /2.5 HDD/SSD 6-1 Retrieve the HDD/SSD tray. 6-2 Install the 3.5 HDD onto the tray. 6-3 Secure the 2.5 HDD/SSD down to the tray with screw-a. 6-4 Insert the tray back into the hard drive cage until the latch clicks. 7. Fan Installation 8. System Ready Fan Hub 7-1 The control panel on TOP I/O can connect up to three fans. Please connect the desired fans to the control panel, and then connect the rest of them to the Fan Hub (the PCB located near M/B). Make sure to connect the fan hub and PSU with a 4-pin Molex connector. 8-1 Slide the side panels back and secure with thumbscrews. 9 All rights reserved by Rosewill

11 8. Optional: Additional Fan & Liquid Cooling Radiator VIPER Z has the capacity of installing one additional 120/140mm fan on top. (connect the fan to either fan hub or the control panel) Instruction of installing 240mm water cooling radiator on the top: Secure the radiator with screws under the top cover. Radiator 10 All rights reserved by Rosewill

12