Hitachi H/EH/EHV Series
|
|
|
- Janice Mathews
- 5 years ago
- Views:
Transcription
1 Hitachi H/EH/EHV Series Supported Series: Hitachi H series, EH-150, Micro-EH, H20, H40, H64, H200, H250, H252, H300, H302, H700, H702, H1000, H1002, H2000, H4010. Website: HMI Setting: Parameters Recommended Options Notes PLC type Hitachi H/EH/EHV Series PLC I/F RS232 RS232, RS485 Baud rate , 19200, Data bits 7 7 Parity Even Even Stop bits 1 1 PLC sta. no Does not apply to this protocol. Online simulator YES Broadcast command NO Extend address mode NO Device Address: Bit/Word Device type Format Range Memo B X HHHHh 0 ~ fffff External input-bit (X) B Y HHHHh 0 ~ fffff External output-bit (Y) B M HHHHh 0 ~ fffff Data area-bit (M) B T HHHHh 0 ~ fffff Timer (T) B R HHHHh 0 ~ fffff Internal output (R) B L HHHHh 0 ~ fffff Link area-bit (L) W TC HH 0 ~ ff Timer/Counter current value W WM HHHH 0 ~ 270f Data area-word (M) W WX HHHH 0 ~ 270f External input-word (X) W WY HHHH 0 ~ 270f External output-word (Y) W WR HHHH 0 ~ c3ff Internal output-word (R) W WL HHHH 0 ~ 270f Link area-word (L)
2 Wiring Diagram: WARNING: If your communication cable is not wired exactly as shown in our cable assembly instructions, damage to the HMI or loss of communications can be caused. CPU TYPE Port 1 Port 2 EH-150/CPU 104A RS-232 RS-232 Port 1 EH-150/CPU 208A RS-232 RS-232 EH-150/CPU 308A RS-232/RS-485 RS-232 Port 2 EH-150/CPU 316A EH-150/CPU 448A RS-232/RS-485 RS-232 RS-232/RS-485 RS-232 Switch Number 1 OFF Normal mode 2 OFF TRNS0 operation 3, Port1 transmission speed ON ON 4,800 bps Doesn t support OFF ON 9,600 bps ON OFF 19,200 bps Default OFF OFF 38,400 bps 5 ON Dedicated port 6 6 PHL Port2 transmission speed ON Low 9,600 bps ON High 38,400 bps OFF Low 4,800 bps Doesn t support OFF High 19,200 bps Default 7 OFF (System mode) Do not turn on. 8 OFF (System mode) Do not turn on. Toggle-Switch PHL Low PHL High
3 The following is the view from the soldering point of a cable. EH-150 port1/port 2 RS232 / MICRO-EH port1 RS232 emt3000 series COM3 RS232 9P RS232 8P RJ45 2 RX 8 RX 5 SD 3 TX 7 TX 6 RD 5 GND 8 CTS 8 RS cmt/mtv series RS232 8P RJ45 2 RX 5 SD 3 TX 6 RD 8 RS MT8000iE/MT8000XE series except MT8050iE RS232 8P RJ45 2 RX 5 SD 3 TX 6 RD 8 CTS 8 RS MT6000/8000 series except MT6050i/MT8050i COM2 RS232 9P COM3 RS232 9P RS232 8P RJ45 D-Sub 2 RX 6 RX 8 RX 5 SD 3 TX 4 TX 7 TX 6 RD 5 GND 5 GND 8 CTS 8 RS
4 MT6050i/MT8050i/MT8050iE RS232 8P RJ45 9 RX 5 SD 6 TX 6 RD 8 RS The following is the view from the soldering point of a cable. EH-150 port1 RS485 4W emt3000 series COM1 RS485 4W 1 RX- 5 TX- 2 RX+ 4 TX+ 3 TX- 6 RX- 4 TX+ cmt/mtv series COM2 RS485 4W 7 RX- 5 TX- 6 RX+ 4 TX+ 9 TX- 6 RX- 8 TX+
5 MT8000iE/MT8000XE series except MT8050iE COM1 RS485 4W COM2 RS485 4W 1 RX- 1 RX- 5 TX- 2 RX+ 2 RX+ 4 TX+ 3 TX- 3 TX- 6 RX- 4 TX+ 4 TX+ 5 GND MT6000/8000 series except MT6050i/MT8050i COM1 RS485 4W 1 RX- 5 TX- 2 RX+ 4 TX+ 3 TX- 6 RX- 4 TX+ MT6050i/MT8050i/MT8050iE COM1 RS485 4W 1 RX- 5 TX- 2 RX+ 4 TX+ 3 TX- 6 RX- 4 TX+ The following is the view from the soldering point of a cable. EH-150 port1 RS485 2W emt3000 series COM1 RS485 2W 1 RX- 6 Data- 4 TX+ 2 RX+ 9 Data+ 5 TX- 6 RX 5 GND
6 cmt/mtv series COM2 RS485 2W 7 RX- 4 Data- 4 TX+ 6 RX+ 1 Data+ 5 TX- 6 RX 5 GND MTx070iE/MT8100iE/MT8121iE/MT8150iE/MT8121XE/MT8150XE COM1 RS485 2W 1 RX- 7 Data- 4 TX+ 2 RX+ 8 Data+ 5 TX- 6 RX 5 GND 9 GND 1 SG MTx071iE/MTx072iE/MT8101iE/MT8090XE/MT8091XE COM2 RS485 2W 1 RX- 6 Data- 4 TX+ 2 RX+ 9 Data+ 5 TX- 6 RX 5 GND MT6000/8000 series except MT6050i/MT8050i COM1 RS485 2W 1 RX- 6 Data- 4 TX+ 2 RX+ 9 Data+ 5 TX- 6 RX 5 GND
7 MT6050i/MT8050i/MT8050iE COM1 RS485 2W 1 RX- 7 Data- 4 TX+ 2 RX+ 8 Data+ 5 TX- 6 RX 5 GND The following is the view from the soldering point of a cable. H Series CPU Port RS232 emt3000 series COM3 RS232 9P RS232 15P D-Sub 2 RX 8 RX 2 TXD 3 TX 7 TX 3 RXD 5 GND 5 GND 9 SG 8 CTS 4 RTS cmt/mtv series RS232 15P D-Sub 2 RX 2 TXD 3 TX 3 RXD 5 GND 9 SG 4 RTS
8 MT8000iE/MT8000XE series except MT8050iE RS232 15P D-Sub 2 RX 2 TXD 3 TX 3 RXD 5 GND 9 SG 8 CTS 4 RTS MT6000/8000 series except MT6050i/MT8050i COM2 RS232 9P COM3 RS232 9P RS232 15P D-Sub D-Sub 2 RX 6 RX 8 RX 2 TXD 3 TX 4 TX 7 TX 3 RXD 5 GND 5 GND 5 GND 9 SG 8 CTS 4 RTS
9 MT6050i/MT8050i/MT8050iE RS232 15P D-Sub 9 RX 2 TXD 6 TX 3 RXD 5 GND 9 SG 4 RTS Driver Version: Version Date Description V1.10 Oct/22/2009 Fixed HMI occupies the control right of CPU module. V1.30 Mar/22/2010
지원기종 : NAIS (Matsushita) FP series include FP-X, FP-Σ, FP0, FP1, FP2, FP2SH, FP10SH and FP3 Ethernet support FP-X with AFPX-COM5.
Panasonic FP 지원기종 : NAIS (Matsushita) FP series include FP-X, FP-Σ, FP0, FP1, FP2, FP2SH, FP10SH and FP3 Ethernet support FP-X with AFPX-COM5. Website:http://pewa.panasonic.com/ [ 편집 ]->[ 시스템파라미터 ]->[
Panasonic FP/KW. HMI Setting: Device Address:
Connection Guide Panasonic FP/KW Supported Series: NAIS (Matsushita) FP/KW series include FP-X, FP-Σ, FP0, FP1, FP2, FP2SH, FP10SH and FP3 Ethernet support FP-X with AFPX-COM5. Website:http://pewa.panasonic.com/
FATEK FB/FBs/B1/B1z Series
Connection Guide FATEK FB/FBs/B1/B1z Series Supported Series: FATEK FB/FBs/B1/B1z series, FB MC series, and FB MA series need FB-DTBR converter. Website: http://www.fatek.com/ Setting: Parameters Recommended
MODBUS RTU (Adjustable)
Connection Guide MODBUS RTU (Adjustable) Supported Series : MODBUS RTU CONTROLLER Website : http://www.modbus.org Setting: Parameters Recommended Options Notes type MODBUS RTU (Adjustable) I/F RS485 /RS485
MODBUS RTU. HMI Setting: PLC Setting: Supported Series : MODBUS RTU CONTROLLER Website :
Connection Guide MODBUS RTU Supported Series : MODBUS RTU CONTROLLER Website : http://www.modbus.org Setting: Parameters Recommended Options Notes type MODBUS RTU I/F RS485 /RS485/USB Baud rate 9600 9600~115200
MODBUS RTU (0x/1x Range Adjustable)
Connection Guide MODBUS RTU (0x/1x Range Adjustable) Supported Series : MODBUS RTU CONTROLLER Website : http://www.modbus.org Setting: Parameters Recommended Options Notes type MODBUS RTU (0x/1x Range
Siemens S7-200 PPI. HMI Setting: PLC Setting: Device Address:
Siemens S7-200 PPI Supported Series: Siemens S7-200 series PLC (CPU212/214/215/216/221/222/224/226/226XM) Website: http://www.siemens.com/entry/cc/en/ HMI Setting: Parameters Recommended Options Notes
Siemens S7-300 MPI. HMI Setting: Device Address: Supported Series: Siemens S7-300 series PLC Website:
Siemens S7-300 MPI Supported Series: Siemens S7-300 series PLC Website: http://www.siemens.com/entry/cc/en/ HMI Setting: Parameters Recommended Options Notes PLC type SIEMENS S7-300 MPI PLC I/F RS-485
T1K MODBUS Base Controller Specifications
Base Controller 1 2 In This Chapter.... Base Controller Setting the DIP Switches Setting the Rotary Address Switches Port Pin out and Wiring RJ12 Serial Port Pin out and Wiring 2 2 Base Controller General
Table of Contents... 1 Operation Mode... 2 Connecting System Menu... 14
v1.4 Hitachi Europe GmbH Industrial Products & Information Systems Am Seestern 18, D-40547 Düsseldorf, Germany tel. +49 211 52830, fax. +49 211 5283 649 http://www.hitachi-ds.com info-dus.pcs@hitachi-eu.com
Device/PLC Connection Manuals
Device/PLC Connection Manuals About the Device/PLC Connection Manuals Prior to reading these manuals and setting up your device, be sure to read the "Important: Prior to reading the Device/PLC Connection
Forcom Technology Co., Ltd. Intelligent RS-485/422 to RS-232 converter
Forcom Technology Co., Ltd. Tel: +886-2-77296880 Fax: +8862-27055495 e-mail: info@forcomtech.com.tw URL: http://www.forcomtech.com.tw Intelligent RS-485/422 to RS-232 converter Model No.: R32TR1 AD-INT
Chapter. Modbus. In This Chapter...
Modbus Communication Chapter 7 In This Chapter... Modbus Protocol....7 2 Registers....7 2 Connection with the DirectLOGIC PLC....7 8 Connection with the C-more and C-more Micro HMI panels....7 10 Modbus
APPLICATION MANUAL for NETWORK
HITACHI PROGRAMMABLE CONTROLLER APPLICATION MANUAL for NETWORK NJI-491A(X) Revision History No. Description of Revision Date of Revision Manual number 1 The first edition 2006.04-2 - Add explanation for
Device/PLC Connection Manuals
Device/PLC Connection Manuals About the Device/PLC Connection Manuals Prior to reading these manuals and setting up your device, be sure to read the "Important: Prior to reading the Device/PLC Connection
XGT/XGB Series Cnet V1.5
XGT/XGB Series Cnet 2 XGT/XGB Series Cnet XGT/XGB SERIES CNET... 1 1. SYSTEM CONFIGURATION... 3 2. SYSTEM SETTINGS... 4 3. EXAMPLE... 6 3.1. EXAMPLE 1... 6 3.2. EXAMPLE 2... 8 4. CABLE WIRING DIAGRAMS...
Device/PLC Connection Manuals
Device/PLC Connection Manuals About the Device/PLC Connection Manuals Prior to reading these manuals and setting up your device, be sure to read the "Important: Prior to reading the Device/PLC Connection
Starter Guide Version Sphinx Access Control System
TC3XYMT/TC3XYNT Starter Guide Version 1.04.1 Sphinx Access Control System Page 1 1. Controller and Reader wiring...3 2. Connect the controller to PC...4 2.1. Setup the ID of Controller...4 2.2. Connect
WIZ125SR User Manual
WIZ125SR User Manual ( Version 1.0 ) 2010 WIZnet Co., Ltd. All Rights Reserved. For more information, visit our website at http://www.wiznet.co.kr WIZ125SR User Manual (WIZnet Co., Ltd.) - 1 - Document
Citect for Windows Driver Specification Extract Hitachi Driver
Citect for Windows Driver Specification Extract Hitachi Driver Author: Date Action Rupert Reeve 13/11/95 Wrote it Bill Rayer 13/12/95 Modifications Masoud Varjavandi 16/1/96 Modified Huang Weiguang 15/12/2000
Wiring Section 3-3. NQ-Series communication ports support various types of (serial) communication.
3-3 Wiring NQ-Series models have, besides one power connector, a number of communication ports. Please refer to Table 2.2: Common specifications for NQ-Series and Table 2.3: Specifications per NQ-Series
Title: Using the AUX Port.
Title: Using the AUX Port. Article Number: 1090 Date: 03/15/05 Information in this article applies to: HMI Silver Series (Enhanced Versions OIT Product(s All Controller (PLC Product(s N/A Summary HMI generation
Device/PLC Connection Manuals
Device/ Connection Manuals About the Device/ Connection Manuals Prior to reading these manuals and setting up your device, be sure to read the "Important: Prior to reading the Device/ Connection manual"
FP7 Connection Manual
PROGRAMMABLE DISPLAY GT series FP7 Connection Manual WUME-GTCONFP7-02 Contents 1. Introduction... 2 1.1 GT Models and Versions Connectable to FP7... 2 1.2 Restrictions... 2 2. Wirings between GT series
Sender Receiver Sender
EEE 410 Microprocessors I Spring 04/05 Lecture Notes # 19 Outline of the Lecture Interfacing the Serial Port Basics of Serial Communication Asynchronous Data Communication and Data Framing RS232 and other
Device/PLC Connection Manuals
Device/PLC Connection Manuals About the Device/PLC Connection Manuals Prior to reading these manuals and setting up your device, be sure to read the "Important: Prior to reading the Device/PLC Connection
User s Guide. Ethernet Module for Barcode Printer
User s Guide Ethernet Module for Barcode Printer 1. ETHERNET MODULE... 2 1-1. Functions... 2 1-2. General Specifications... 2 2. ETHERNET MODULE INSTALLATION... 3 2-1. Ethernet Module Installation for
BACnet/MSTP. HMI Setting: How to Import Tags: Supported series: BACnet/MSTP protocol devices
Connection Guide BACnet/MSTP Supported series: BACnet/MSTP protocol devices Setting: Parameters Recommended Options Notes type BACnet/MSTP I/F RS485-2W Baud rate 38400 9600,19200, 38400 Data bits 8 Parity
Title: Using the AUX Port.
Title: Using the AUX Port. Article Number: 1090 Date: 07/10/06 Information in this article applies to: HMI Silver Series (Enhanced Versions) OIT Product(s) All Controller (PLC) Product(s) N/A Summary HMI
EX KVIS RS232/422/485 3-in-1 Serial to USB Adapter (w/ 4KV Isolation, 15KV ESD Surge Protection)
EX-1331-4KVIS RS232/422/485 3-in-1 Serial to USB Adapter (w/ 4KV Isolation, 15KV ESD Surge Protection) 1. Introduction Thank you for purchasing this RS232/422/485 3-in-1 Serial to USB Adapter. It is an
SCB-C08 USB to RS232/422/485 Converter
SCB-C08 USB to RS232/422/485 Converter USB Interface RS-232 signal RS-422 signal: RS-485 signal: Cable Type Transmission distance Signal LED Direct power from USB port Power consumption: Compliant with
SAPHIR SIO Driver. Siemens Building Technologies
Siemens Building Technologies SAPHIR SIO Driver 1 System Configuration... 3 2 External Device Selection... 6 3 Communication Settings... 7 4 Setup Items... 9 5 Cable Diagrams... 14 6 Supported Devices...
Industrial Serial Device Server
1. Quick Start Guide This quick start guide describes how to install and use the Industrial Serial Device Server. Capable of operating at temperature extremes of -10 C to +60 C, this is the Serial Device
Pass-Through Function
Pass-Through Function Chapter 29 Pass-through Function... 2 29.1 Ethernet Mode... 3 29.1.1 How to install virtual serial port driver... 3 29.1.2 How to Change the Virtual Serial Port... 4 29.1.3 How to
ACE PLUS CORP. APCON100 series Operation Manual RS-232 to Ethernet Converter
APCON100 series Operation Manual RS-232 to Ethernet Converter Page 1 of 24 APCON100 series Operation Manual Index Chapter 1 Specifications 2 Chapter 2 Introduction 3 Chapter 3 Easy Installation 4 Chapter
3.1 I-7560 Pin Assignment and Specifications: Introduction
3.1 I-7560 Pin Assignment and Specifications: Introduction The I-7560 adds a Windows serial Com port via its USB connection and is compatible with new & legacy RS-232 devices. USB Plug and Play allows
TABLE OF CONTENTS. Communication Functions
TABLE OF CONTENTS Chapter 1: Chapter 2: Chapter 3: Chapter 4: General Features....................................................... 1-1 Functions......................................................
TRP-C08. USB to RS232/422/485 Isolated Converter. User s Manual. Printed Sep.2014 Rev 1.4
TRP-C08 USB to RS232/422/485 Isolated Converter User s Manual Printed Sep.2014 Rev 1.4 Trycom Technology Co.,Ltd No.35, Zhongxing Rd., Guishan Township, Taoyuan County 333, Taiwan. Tel : 886-3-350-3351
RS-232/422/485 to Copper or Fiber. Ethernet Converter. User s Manual
RS-232/422/485 to Copper or Fiber Ethernet Converter User s Manual Table Of Contents TABLE OF CONTENTS... 1 INTRODUCTION... 3 PRODUCT OVERVIEW... 3 PRODUCT FEATURES... 3 PACKING LIST... 4 LED INDICATORS...
PLC Connection Guide. Parameters Recommended Options Notes
SHIMADEN M13/FP93 Supported Series: M13, FP93 devices Website: http://www.shimaden.co.jp HMI Setting: Parameters ecommended Options Notes PLC type SHIMADEN M13/FP93 PLC I/F S485 Baud rate 9600 1200-19200
DT Desktop Series
5600-8-DT Desktop Series Compact 8-port Serial s Features 8 ports supporting RS-232, RS-422, or RS-485 operation Compact desktop size Auto-detecting 10/ 100 Mbps Ethernet 15 KV ESD surge protection for
Connection Cable Communication 232C Port Method GP 1762-L24BWA. the CPU Unit RS-232C
System Structure GP Model Product Remark GP GP70 Series GP77 / 77R Series GP2000 Series GLC GLC2000 Series * Information for connecting Handy Type is not on this instruction. PLC CPU Connection Cable Communication
VISY-X. Technical Documentation. Cinterion MC 55 i. Edition: Version: 1 Article no.:
Technical Documentation VISY-X Edition: 2016-10 Version: 1 Article no.: 350033 FAFNIR GmbH Schnackenburgallee 149 c 22525 Hamburg Tel.: +49 / 40 / 39 82 07 0 Fax: +49 / 40 / 39 06 339 Table of contents
Max. Shock Acc. :147 m/s{15g} Time: 11ms Pulse Wave: Half Since Wave Pulse (3 times in X,Y,Z) IEC IEC Fast Transient Power Module
FEATURES Multi Drop Configuration of up to 32 units Baud Rates Ranging from 300 to 38,400bps 1:1 /1:N / N:M (RS-422) Communication is Supported Supports Full-Duplex (RS-422) and Half-Duplex (RS-485) Built-in
XGK Series CPU Direct Driver
LS Industrial Systems Co., Ltd. XGK Series CPU Direct Driver 1 System Configuration... 3 2 Selection of External Device... 6 3 Example of Communication Setting... 7 4 Setup Items... 9 5 Cable Diagram...
Connecting UniOP to the ABB 07KT97 Controllers
Connecting to the ABB 07KT97 Controllers This Technical Note contains the information needed to connect to the ABB 07 KT 97 controllers. The ABB 07 KT 97 supports communication via standard Modbus RTU
Parameters Recommended Options Notes PLC type
SHIMADEN M13/FP93 Supported Series: M13, FP93 devices Website: http://www.shimaden.co.jp HMI Setting: Parameters ecommended Options Notes PLC type SHIMADEN M13/FP93 PLC I/F Baud rate 9600 1200-19200 Data
CONTROLLER INFORMATION SHEET
CONTROLLER INFORMATION SHEET Maple Model(s) Graphic HMIs PLC or Controller Modbus RTU P/N: 1036-0045 Rev. 06 Date: 09/17/2015 Summary Maple Systems Graphic HMIs communicate with any device that uses the
Tel: Fax:
NP302 Series 2-port RS-232 232/485/422 to Ethernet Serial Server User manual Shenzhen 3onedata Technology Co.,Ltd Tel: +86-755-26702688 Fax: +86-755-26703485 www.3onedata.com Contents 1. Introduction...
Controlling the projector using a personal computer
DLP Projector EX320U/EW330U/EX320U-ST Controlling the projector using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal. PC-controllable functions:
PCI Express 16-Port Serial I/O Cards
PCI Express 16-Port Serial I/O Cards The PCIe-1600 PCI Express 16-port serial I/O card is a plug & play high-speed serial I/O expansion card for PCI Express bus. Connecting to a PCI Express bus on your
WiFi to RS-232 adapter user manual
WiFi to RS-232 adapter user manual WiFi to RS-232 adapter Package Contents: WiFi RS-232 adapter x 1 A4 User manual x 1 Mini USB Cable x 1 White Box Dimension: 11 x 6 x 5 (cm) Total Package Weight: 126
GEM80 & ewon Setup Quick Guide
Introduction to the ewon The ewon is an intelligent, programmable Ethernet Gateway, which can be used to bridge GEM 80 PLCs onto an Ethernet network, via the PLC serial port (Port3). This provides network-based
VS-626M5 Parameter Upload/Download Software User s Manual (Preliminary) 5/18/99
VS-626M5 Parameter Upload/Download Software User s Manual (Preliminary) 5/18/99 Computer Requirements The following hardware and software are required to run the M5 Parameter Upload/Download software.
Citect for Windows Driver Specification Extract
Citect for Windows Driver Specification Extract Trio Driver Author: Philip Wong Date: 16/6/95 Modified: David Rossini Date: 17/02/98 Contents 1. TARGET DEVICE...4 1.1 INTRODUCTION...4 1.2 DEVICE MANUFACTURER...4
Appendix A Cable Pinouts
Appendix A Cable Pinouts This appendix lists the cables and connector pinout assignments for the cables used with the ERX-7xx models and ERX-14xx models. Topic Page SRP I/O Module 163 CT1 and CE1 I/O Modules
Serial to Ethernet Converter HL-SE02P-V1. User s Manual V3.606
Serial to Ethernet Converter HL-SE02P-V1 User s Manual V3.606 UContents Table Welcome... 2 Package Contents. 2 Feature. 2 Application 3 Specification. 4 Hardware Guide 5 Ping Assignments. 6 Factory Default
DNC Setups by Predator - Licensed Use Only
To: Predator DNC Administrator From: www.support.predator-software.com Sent: August 20, 2001 Subject: Predator DNC Setups are organized into seperate steps. Complete each step in order before proceding.
Basics of UART Communication
Basics of UART Communication From: Circuit Basics UART stands for Universal Asynchronous Receiver/Transmitter. It s not a communication protocol like SPI and I2C, but a physical circuit in a microcontroller,
Attaching Inputs and Outputs
Attaching Inputs and Outputs Inputs (sources) and outputs (destinations) attach to the input and output connectors on the rear of each enclosure. Inputs attach to the connectors on the left side of the
Bluetooth TO Serial CONVERTER E-P132-B
Bluetooth TO Serial CONVERTER E-P132-B 1 Table of Contents Introduction..3 Package checklist...4 Product Specification...5 Product Panel Views Description...6 Product Views. 6 DC-In Power Outlet 6 Antenna
Cable Pinouts. SRP I/O Module
Cable Pinouts A This appendix lists the cables and connector pinout assignments for the cables used with the ERX-7xx models and ERX-14xx models. Topic Page SRP I/O Module A-1 CT1 and CE1 I/O Modules A-4
RS-232 / RS-422 / RS-485 over Fast Ethernet Media Converter
RS-232 / RS-422 / RS-485 over Fast Ethernet Media Converter Serial Interface One RS-232/422/485 port to one 100Base-FX Media Converter Cost-effective solution for RS-232 to Ethernet application Supports
Controlling the projector using a personal computer
DLP Projector EX320U/EW330U/EX320U-ST/EX321U-ST/EW331U-ST/EX321U Controlling the projector using a personal computer This projector can be controlled by connecting a personal computer with RS-232C terminal.
Device/PLC Connection Manuals
Device/PLC Connection Manuals About the Device/PLC Connection Manuals Prior to reading these manuals and setting up your device, be sure to read the "Important: Prior to reading the Device/PLC Connection
Cabling Guide for Console and AUX
Page 1 of 13 Cabling Guide for and AUX Ports TAC Notice: What's Changing on TAC Web Help us help you. Contents Introduction Before You Begin Conventions Prerequisites Components Used Table of Routers with
PC CONNECTION Programmable Terminal OPERATION MANUAL
Cat No. V042-E1-1 PC CNECTI Programmable Terminal OPERATI MANUAL PLC CNECTI Programmable Terminal Operation Manual Produced April 1997 iii OMR Product References All OMR products are capitalized in this
USER S MANUAL. PH232Ex1. #1 RS-232 Serial Port to Ethernet, Terminal Server/Client. Doc No: PH232Ex1-UM-001 IPEX. (IP Electronix)
USER S MANUAL PH232Ex1 Doc No: PH232Ex1-UM-001 #1 RS-232 Serial Port to Ethernet, Terminal Server/Client IPEX (IP Electronix) Contents 1. INTRODUCTION... 3 2. SPECIFICATIONS... 3 3. PACKAGE CHECKLIST...
Bluetooth to RS-232 Converter. RT-132B Bluetooth Adaptor Operation Manual
Bluetooth to RS-232 Converter RT-132B Bluetooth Adaptor Operation Manual First Edition, Nov 2007 Table of Contents 1. Introduction.. 2 2. Package checklist.. 3 3. Product Specification... 4 4. Product
COMMUNICATION INSTRUCTION MANUAL Temperature Controller KT4R
COMMUNICATION INSTRUCTION MANUAL Temperature Controller KT4R No. KT4RCE1 2015.06 This manual contains instructions for communication functions of the KT4R. To prevent accidents arising from the misuse
INDUSTRIAL ETHERNET MODULE TBOX Manual
INDUSTRIAL ETHERNET MODULE TBOX Manual XINJE ELEC. CO., LTD CONTECTS 1 INTRODUCTION...1 2 COM PORT AND DISPLAY......3 3 PARAMETER SETTING...8 1 INTRODUCTION 1. Brief introduction Modbus protocol is industrial
IAI Corporation 1998, 1999, For Reference Only.
IAI Corporation 1998, 1999, 2000. For Reference Only. Table of Contents DRIVER BENEFITS 3 EXOR DESIGNER BENEFITS 3 PROBLEMS FOUND 4 WHAT IS NEEDED TO RUN EXOR 4 HOW TO CONNECT 4 TYPICAL SYSTEM DIAGRAM
MEDIA OVER IP SYSTEM B-900-MOIP-CTRL B-900-MOIP-4K-TX B-900-MOIP-4K-RX 4 IR &RS-232/SERIAL FUNCTIONALITY
MEDIA OVER IP SYSTEM B-900-MOIP-CTRL B-900-MOIP-4K-TX B-900-MOIP-4K-RX 4 IR &RS-232/SERIAL FUNCTIALITY 2 9 11 13 15 10 12 14 16 RS-232 SERIAL CTROL How Does MoIP RS-232 Serial Control Work? MoIP features
Modbus Gateway User's Manual ADM-5850G
Modbus Gateway User's Manual ADM-5850G Functional introduction The Modbus protocol is the most widely used protocol in the electronic industrial equipment, and now it has become a general industrial standard.
Ethernet to Serial Port Module RS-232/422/485 to Internet Gateway
Ethernet to Serial Port Module RS-232/422/485 to Internet Gateway (Model: IPM-S) Wireless Gateway: Active RFID Gateway Bluetooth to Internet Application: Energy Meter Networks Motor Control Industrial
ABLELink. Modbus Gateway MB5000 Series User s Manual
ABLELink MB5000 Series User s Manual Version 1.1 Updated in March, 2010 TEL: 886-3-5508137 FAX: 886-3-5508131 http://www.atop.com.tw Table of Contents Table of Contents... 2 Introduction... 4 Features...
USB-COM Plus ISO (USB-COMi SI-M)
VS Vision Systems GmbH / Part Number 603 Features 1 x RS232/422/485 port USB 2.0 Full Speed interface 2.5kV isolation per serial port USB and serial ports ESD protected Robust metal case Jumperless, DIP
MODBUS-IN. Modbus Card. User & Installation Manual Xtreme Power Conversion Corporation. All rights reserved.
MODBUS-IN User & Installation Manual www.xpcc.com 2014. All rights reserved. (Rev 12/17/14) Thank you for purchasing. This manual contains instructions and warnings that should be followed during the installation,
SIMATIC S5 CPU Direct Driver
Siemens AG SIMATIC S5 CPU Direct Driver 1 System Configuration... 3 2 Selection of External Device... 7 3 Example of Communication Setting... 8 4 Setup Items... 9 5 Cable Diagram... 14 6 Supported Device...
PCIe Card Selection Guide. PCIe-CAN Card. PCIe-COM Card. Taiwan Pulse Motion Co.,Ltd. Bus Interface PCI Express x 1 LPE-C122 PCE-C122D PCE-C122T
PCIe Card Selection Guide PCIe-CAN Card Bus Interface PCI Express x 1 LPE-C122 PCE-C122D PCE-C122T Channels I/O Isolation Voltage Baud Rate Terminator Resistor I/O PIN Type 2 Max. 1 Mbps Jumper for 120
IM3523 IM3533 IM IM3536 LCR METER IM3570 IM7580 IM3590 CHEMICAL IMPEDANCE ANALYZER IMPEDANCE ANALYZER. Communication Instruction Manual
Communication Instruction Manual IM3523 IM3533 IM3533-01 IM3536 LCR METER IM3570 IM7580 IMPEDANCE ANALYZER IM3590 CHEMICAL IMPEDANCE ANALYZER November 2014 Revised edition 6 IM3570A983-06 14-11H i Contents
EZL-200F Application Notes (003) Serial Interface (RS232/RS422/RS485)
Application Notes (003) Serial Interface (RS232/RS422/RS485) Version 2.0 Sollae Systems Co., Ltd. 1. Overview supports three serial interfaces: RS232, RS422, and RS485. You can select the interface you
Cable Specifications. Interface Specifications. Fiber-Optic Specifications APPENDIXB
APPENDIXB This appendix lists the cable specifications for supported modules on the Cisco 7600 series router. The following signal summaries are contained in this appendix: Interface Specifications, page
FEC-240G. Rev. Date
Model User s Manual Contents Contents. 1 Features... 2 Type Model and Serial Number... 2 Specifications... 3 Interface Connections...... 4 DIP Switch Setting... 6 Dimension... 7 Command Set Table... 8
SIMATIC S5 CPU Direct Driver
Siemens AG SIMATIC S5 CPU Direct Driver 1 System Configuration... 3 2 Selection of External Device... 6 3 Example of Communication Setting... 7 4 Setup Items... 8 5 Cable Diagram... 13 6 Supported Device...
5600 Series. 8 and 16-port Serial Device Servers. Features. Internet Readiness for up to 16 Serial Devices
5600 Series 8 and 16-port Features Up to 16 ports supporting RS-22, RS-422, or RS-485 operation Compact desktop model or standard 19-inch rackmount model Auto-detecting 10/100 Mbps Ethernet 15 KV ESD surge
VIGOR PROGRAMMABLE LOGICAL CONTROLLERS VIGOR ELECTRIC CORP.
VIGOR PROGRAMMABLE LOGICAL CONTROLLERS VIGOR ELECTRIC CORP. 232G RX TX VB-1COM VIGOR + 24V IN - SHORT FOR TR 485G D+ D- VB-1COM Serial Foreword This manual contains text, diagrams and explanations which
Delta Controller ASCII/RTU
DOP_W_EN_20110516 Delta ASCII/RTU HMI Factory Setting: Baud rate: 9600, 7, None, 2 (ASCII); 9600, 8, None, 2 (RTU) Station Number: 1 Control Area / Status Area: None/None Connection Delta Servo a. RS-232
This 4-port RS-422/485 Adapter is provided with an external switching power adapter in the package.
USB-4COMi-M USB to Quad RS-422/485 to Serial Adapter Manual The USB to Industrial Quad RS-422/485 Adapter is designed to make industrial communication port expansion quick and simple. Connecting to a USB
The modems are made in industrial 108mm wide aluminium housing for DIN rail mounting. UCM RS232 interface
DESCRIPTION The modems are a series of general-purpose industrial modems, which can be used for data communication through Public Switched Telephone Networks (PSTN). The modems can operate in 2-wire, full-duplex,
(V 1.1) 2006 WIZnet Inc. All Rights Reserved. For more information, visit our website at 0/23
EG-SR-7150MJ User s Manual (V 1.1) 2006 WIZnet Inc. All Rights Reserved. For more information, visit our website at http://www.wiznet.co.kr 0/23 If you have any question about WIZnet Products, write them
Connection Guide (RS-232C)
Programmable Controller CJ-series General-purpose Serial Connection Guide (RS-232C) MARS TOHKEN SOLUTION CO.LTD. Fixed Mount 2D Image Reader (MVF-300/500 Series) P679-E1-01 About Intellectual Property
Weintek Remote IO (CANopen)
Weintek Remote IO (CANopen) Supported series: ir-di16-k, ir-dm16-p, ir-dq16-p, ir-dm16-n, ir-dq16-n, ir-dm16-r, ir-dq16-r, ir-ai04-vi, IR-AQ04-VI, ir-am06-vi, ir-ai04-tr HMI Setting: Parameters Recommended
PCI Express 4-Port Industrial Serial I/O Cards
PCI Express 4-Port Industrial Serial I/O Cards The PCIe-400i and PCIe-400i-SI PCI Express 4-port industrial serial I/O cards are plug & play high-speed serial I/O expansion cards for the PCI Express bus.
Automationdirect.com. D i r e c t L o g i c M O D B U S S L A V E F 4 S L V - M B
Automationdirect.com D i r e c t L o g i c 4 0 5 M O D B U S S L A V E F 4 S L V - M B Order Number: F4-SLVMB-M Automationdirect.com is a Trademark of Automationdirect.com Modbus is a Trademark of Gould
OMRON Corporation PLC SYSMAC CJ1M Series Connection
OMRON Corporation PLC SYSMAC CJ1M Series Connection Let s Connect to PLC! System Structure GP Product Model Remark GP GLC GP70 Series GP77/77R Series GP2000 Series GLC2000 Series Excepting for handy types.
ASYNC Sharing Unit TABLE OF CONTENTS SECTION 1 - DESCRIPTION...2 SECTION 2 - SPECIFICATIONS...5 SECTION 3 - INSTALLATION...7
ASYNC Sharing Unit TABLE OF CONTENTS SECTION 1 - DESCRIPTION... SECTION - SPECIFICATIONS... SECTION - INSTALLATION... SECTION - FRONT PANEL CONTROLS AND INDICATORS...9 SECTION - NETWORK MANAGEMENT PORT...10
Embedded Modbus TCP Module GS11-MT. User Manual REV 1.1. SST Automation.
Embedded Modbus TCP Module GS11-MT User Manual REV 1.1 SST Automation E-mail: SUPPORT@SSTCOMM.COM WWW.SSTCOMM.COM Catalog 1 About the Embedded Module... 4 1.1 General...4 1.2 Features... 4 1.3 Specifications...4
HMI and micro printer Connection manual
HMI and micro printer Connection manual WUXI XINJE ELECTRIC CO., LTD. Data No. HC 11 20130226 2D 1 Catalog 1. TOUCHWIN V2.C.6 SOFTWARE... 3 1.1 Type choice... 3 1.1.1 Printer type... 3 1.1.2 HMI type...
PCL Port RS-232 Interface Card
PCL-858 8-Port RS-232 Interface Card Copyright Notice This documentation and the software included with this product are copyrighted 2001 by Advantech Co., Ltd. All rights are reserved. Advantech Co.,