Instructions. (For 6180 Industrial Computers) Applications. Overview & Safety

Transcription

1 Instructions (For 6180 Industrial Computers) Applications This instruction sheet describes how to replace the following displays and backlights for 6180 Industrial Computers. All display kits contain a hinge pin and 3 chassis latching screws. Item See Page 10.4 Inch Bezel / Display Inch Touchscreen / Display Inch Bezel / Display Inch Touchscreen Bezel / Display 4 Plastic Bezel No Display 4 Replacement Backlight (Catalog No NL2) 10.4 Inch Display Only 2 Overview & Safety The backlight uses Cold Cathode Fluorescent (CCF) tubes to illuminate the display. The 11.3 inch displays have an integral backlight that cannot be replaced separately, the entire bezel / display must be replaced. The 10.4 inch backlight is replaceable.! ATTENTION: Disconnect all power from the 6180 Computer before replacing the backlight. Failure to disconnect power may result in electrical shock and/or damage to the terminal.! ATTENTION: Do not touch any of the exposed electronic components to prevent damage from electrostatic discharge (ESD).

2 2 Display and Backlight Replacing the 10.4 Inch Display Backlight To replace the backlight (10.4 inch displays only): 1. Disconnect the power from the 6180 Computer. 2. Remove the three latching screws that secure the chassis to the front bezel Front Bezel Latching Screws (3) 3. Note the following precautions before swinging the chassis away from the bezel.!! ATTENTION: Remove all external cables from the side panel connectors. Failure to remove cables may cause damage to the cables and connectors. ATTENTION: If the 6180 Computer is installed with mounting clips, the mounting clips on the hinge side will interfere with the opening of the hinge. Remove the mounting clips on the hinge side before swinging chassis away from the bezel. Failure to remove clips may damage clips and the chassis. 4. Swing the chassis open about 90.

3 Display and Backlight 3 Backlight Power Supply Cable (4) M4 Phillips Screws 5. Remove four screws that secure backlight and remove the backlight to allow access to the power connector 6. Unplug the backlight power supply cable and remove the backlight. 7. Plug the backlight power supply cable into the new backlight. 8. Place the backlight on the four backlight standoffs. 9. Replace the four backlight mounting screws and tighten to a torque of 6 to 8 inch-pounds (.7 to.9 N m). 10. Swing the chassis back into position and tighten the three latching screws to a torque of 18 to 22 inch-pounds (2 to 2.5 N m). 11. Reconnect and install any external cables or mounting clips. 12. Apply power and verify operation of the backlight.

4 4 Display and Backlight Replacing the 10.4, 11.3 Inch Displays or Bezel with No Display The procedures for replacing 11.3 and 10.4 inch bezel/displays are the same. For purposes of illustration we show the 11.3 inch display. If you are installing a bezel with no display, the procedures are the same except for the number of electrical connectors to the bezel. To remove a 10.4 or 11.3 inch bezel/display: 1. Disconnect the power from the 6180 Computer. 2. Disconnect all communication and power cables. 3. Remove the clips or mounting stud nuts that secure the computer to the panel. Important: There is metal tab that temporarily locks the bottom of the chassis in the panel during mounting. This tab must be bent in before bezel / chassis can be removed. Ï Bezel Locking Tab Gasket Panel 4. Remove the computer from the panel or enclosure.

5 Display and Backlight 5 5. Remove the three latching screws that secure the chassis to the front bezel. Front Bezel Latching Screws (3) 6. Swinging the chassis open about Disconnect the electrical connectors from the front panel. Note the location and orientation of the connectors. Disconnect Electrical Connectors

6 6 Display and Backlight 8. Drive the hinge pin up using a slotted screwdriver (under the head of the hinge pin) and a small hammer. Hinge Pin 9. Remove the bezel/display from the chassis.

7 Display and Backlight 7 To install a 10.4 or 11.3 inch display: 1. Secure the bezel/display to the chassis by aligning the hinges and installing the hinge pin. 2. Connect the electrical connectors between the bezel/display and the chassis. The connectors are different sizes and each is keyed so that they cannot be installed incorrectly. Do not force a connector. 3. Swing the chassis closed. Make sure the bezel/display cables and connectors move freely and do not crimp when the chassis is closed. 4. Secure the chassis with the three latching screws. Use the new screws provided. 5. Mount the 6180 Computer in the the enclosure or panel, refer to the 6180 Industrial Computer user manual. 6. Apply power and verify operation of the display.

8 Allen-Bradley, a Rockwell Automation Business, has been helping its customers improve productivity and quality for more than 90 years. We design, manufacture and support a broad range of automation products worldwide. They include logic processors, power and motion control devices, operator interfaces, sensors and a variety of software. Rockwell is one of the world s leading technology companies. Worldwide representation. Argentina Australia Austria Bahrain Belgium Brazil Bulgaria Canada Chile China, PRC Colombia Costa Rica Croatia Cyprus Czech Republic Denmark Ecuador Egypt El Salvador Finland France Germany Greece Guatemala Honduras Hong Kong Hungary Iceland India Indonesia Ireland Israel Italy Jamaica Japan Jordan Korea Kuwait Lebanon Malaysia Mexico Netherlands New Zealand Norway Pakistan Peru Philippines Poland Portugal Puerto Rico Qatar Romania Russia CIS Saudi Arabia Singapore Slovakia Slovenia South Africa, Republic Spain Sweden Switzerland Taiwan Thailand Turkey United Arab Emirates United Kingdom United States Uruguay Venezuela Yugoslavia Allen-Bradley Headquarters, 1201 South Second Street, Milwaukee, WI USA, Tel: (1) Fax: (1) (B) Copyright 1997 Allen-Bradley Company, Inc. Printed in USA