Toshiba Satellite E105-S1602 Cooling Fan

Transcription

1 Toshiba Satellite E105-S1602 Cooling Fan Replacement Use this guide to replace/remove the cooling fan in your device. Rédigé par: Ian Washburne ifixit CC BY-NC-SA fr.ifixit.com Page 1 de 14

2 INTRODUCTION The cooling fan keeps the device from overheating. If a device overheats, it can shut down. OUTILS: Phillips #00 Screwdriver (1) ifixit Opening Tools (1) ifixit CC BY-NC-SA fr.ifixit.com Page 2 de 14

3 Étape 1 Battery Slide both of the latches to the outside to release the battery. Étape 2 Pull the battery out by lifting the battery cover away from the laptop. ifixit CC BY-NC-SA fr.ifixit.com Page 3 de 14

4 Étape 3 Keyboard Flip the computer over and insert the plastic opening tool under the plastic strip at the top of the keyboard. Pry the top plastic strip from the top of the keyboard. Peel the strip completely away from the keyboard. Étape 4 Using your Phillips #00, unscrew the two 4.80mm screws at the top of the keyboard. ifixit CC BY-NC-SA fr.ifixit.com Page 4 de 14

5 Étape 5 When removing the keyboard, be careful not to rip the ribbon cable connecting the keyboard to the computer, to avoid damaging it. Flip the keyboard up from the bottom in order to see the two ribbons connecting it to the motherboard. Étape 6 Using the plastic opening tools, pop out the ribbon cable from the rest of the computer. ifixit CC BY-NC-SA fr.ifixit.com Page 5 de 14

6 Étape 7 Using the plastic opening tools, pop out the second ribbon cable from the rest of the computer. Étape 8 Completely remove the keyboard from the laptop by lifting up the part closest to the screen, and then gently pulling out the bottom half. Keep the keyboard safe by storing it on a flat, non-metallic surface until needed. ifixit CC BY-NC-SA fr.ifixit.com Page 6 de 14

7 Étape 9 Front Panel Locate the four silver screws on the front panel. Using the Phillips #0, unscrew to remove all four 2.95mm silver screws. Étape 10 Flip the laptop over and locate all seven screws on the bottom of the laptop. Unscrew all seven Philips# mm screws. ifixit CC BY-NC-SA fr.ifixit.com Page 7 de 14

8 Étape 11 Locate and unscrew the three silver Philips # mm screws inside the battery compartment. Locate and unscrew the five black Philips # mm screws inside the battery compartment. Étape 12 Rotate the laptop so the back faces you. Locate the two black Philips # screws, one by each hinge, and remove. ifixit CC BY-NC-SA fr.ifixit.com Page 8 de 14

9 Étape 13 Use the plastic opening tool to pry the top panel up from the base of the computer. Slowly work your way around the computer with the plastic removing tool to make it easier to lift the top panel away from the base. Carefully lift the top panel no more than six inches, as there are ribbon cables connecting the two pieces. Disconnect ribbons, and slowly lift the top panel up, away from the base. Étape 14 Locate the ribbon cable from the motherboard. Using plastic removing tools, pop the ribbon base from the motherboard. ifixit CC BY-NC-SA fr.ifixit.com Page 9 de 14

10 Étape 15 Locate the two plugs from the motherboard. Using plastic opening tools, remove each plug from the motherboard. Étape 16 Locate the ribbon cable partially hidden under the front panel. Using plastic opening tools, pop out the ribbon cable from the motherboard. ifixit CC BY-NC-SA fr.ifixit.com Page 10 de 14

11 Étape 17 Make sure that all wires have been disconnected before proceeding to avoid damaging components. Slowly lift the top panel away from the base of the computer. Place the top panel away from the computer and keep in a flat nonmetallic surface until needed. Étape 18 Cooling Fan Locate the fan in the back left corner of the motherboard. ifixit CC BY-NC-SA fr.ifixit.com Page 11 de 14

12 Étape 19 Rotate the laptop so the cooling fan is closest to you. Locate the piece of electrical tape holding the screen wired, on top of the fan. Tear away the piece of electrical tape. Étape 20 Find the screen wires that the tape was holding down and move them off to the side. Locate and pop out the plug connecting the fan to the motherboard. ifixit CC BY-NC-SA fr.ifixit.com Page 12 de 14

13 Étape 21 Locate and remove the three Philips # mm screws holding the fan in. Étape 22 Lift the fan straight up and out of the computer. Look for and remove any built up dust, lint, hair. To reassemble your device, follow these instructions in reverse order. ifixit CC BY-NC-SA fr.ifixit.com Page 13 de 14

14 Ce document a été généré pour la dernière fois le :07:23 AM. ifixit CC BY-NC-SA fr.ifixit.com Page 14 de 14