Physical Specification Vending Machine Card Reader Module Model: CRM-170-xx

Transcription

1 Vending Machine Card Reader Module Model: CRM-170-xx Version C (26/08/05)

2 Contents Section Title Page 1 Component Layout 3 2 Cables Executive Power Executive Data - External Executive Data Internal MDB Power&Data Gender Changer MDB Power&Data Extender Card Reader Interface 7 3 Headers CONN CONN CONN CONN CONN5 8 4 Electrical 9 5 Case Assembly / Removal 10 6 Change Control 12 Page 2 of 12

3 2. Component Layout CONN4 Transaction Cancel & VMC Selection Emulation XPort Ethernet Network Socket Slot B: VMC Firmware Slot Slot A: AVI Firmware Slot CONN1 MDB Data&Power / Exec power Figure 2.1 Top View Without Case Page 3 of 12

4 CONN2 Executive Data Header SW Reset to factory defaults CONN3 Card Reader Header MSR 170 Card Reader Header Figure 2.2: Rear View Without Case Page 4 of 12

5 Cable Exit for Transaction Cancel Button CONN1 MDB Data&Power / Exec power XPort Network socket Access hole to SW Reset to factory defaults CONN5 Executive Data Figure 2.3: Rear View With Case Page 5 of 12

6 2 Cables 2.1 Executive Power Connects CONN1 (Con.1) to VMC Executive Power Interface (Con.2) Neuroscot Part No. CRM-CAB-A109 Length 1000mm Wires 2 Con.1 Pin Con.2 Pin Wire Colour Function 1 1 Black AC Black Supply (24v AC) AC 1 3 n/c 4 n/c 5 n/c 6 n/c 2.2 Executive Data External Connects Executive Data Case Connector CONN5 (Con.2) to VMC Executive Data Interface (Con.1). Neuroscot Part No. CRM-CAB-A107 Length 1000mm Wires 4 Con.1 Pin Con.2 Pin Wire Colour Function 1 1 Blue Tx +ve 2 2 Green Rx ve 3 3 Yellow Rx +ve 4 4 Orange Tx -ve 2.3 Executive Data Internal Connects Case (Con.2) and CONN2 (Con.1). Provides CONN5 see Figure 3 above. Neuroscot Part No. CRM-CAB-A108 Length 150mm Wires 4 Con.1 Pin Con.2 Pin Wire Colour Function 2 1 Blue Tx +ve 3 2 Green Rx -ve 1 3 Yellow Rx +ve 4 4 Orange Tx -ve 5 n/c Page 6 of 12

7 2.4 MDB Power&Data Gender Changer Connects VMC MDB Interface Cable (Con.2) to CONN1 (Con.1). Neuroscot Part No. CRM-CAB-A106 Length 1000 Wires 5 Con.1 Pin Con.2 Pin Wire Colour Function 1 1 Red + D.C. supply 2 2 Black D.C. Return 3 3 N.C. 4 4 Blue Master Rx 5 5 Green Master Tx 6 6 Brown Communications ground 2.5 MDB Power&Data Extender Connects VMC MDB Interface Cable (Con.2) to CONN1 (Con.1). Neuroscot Part No. CRM-CAB-A105 Length 1000 Wires 5 Con.1 Pin Con.2 Pin Wire Colour Function 1 1 Red + D.C. supply 2 2 Black D.C. Return 3 3 N.C. 4 4 Blue Master Rx 5 5 Green Master Tx 6 6 Brown Communications ground 2.6 Card Reader Interface Connects MSR-170 Card Reader Header (Con.2) to CONN3 (Con.1) Neuroscot Part No. CRM-CAB-A110 Length 120mm Wires 7 Con.1 Pin Con.2 Pin Wire Colour / NJ Pin Function 1 A10 Black Gnd 2 B10 Black +5v 3 B4 Yellow S2 Sensor 4 A4 Yellow S1 Sensor 5 A3 Orange CLS 6 B2 Red RCP 7 A2 Red RDP Page 7 of 12

8 3. Headers 3.1 CONN1 - MDB Data&Power / Exec power Molex: CONN1 Pin Function 1 + D.C. supply 2 D.C. Return 3 N.C. 4 Master Rx 5 Master Tx 6 Communications ground 3.2 CONN2- Executive Data Interface Molex: CONN2 Pin Function 1 Tx +ve 2 Rx ve 3 Rx +ve 4 Tx -ve 3.3 CONN3 - Card Reader Interface Molex: Con.1 Pin Function 1 Gnd 2 +5v 3 S2 Sensor 4 S1 Sensor 5 CLS 6 RCP 7 RDP 3.4 CONN4 Module Reset / Selection Emulation Molex: CONN5 Executive Data Interface Molex: CONN5 Pin Function 1 Tx +ve 2 Rx -ve 3 Rx +ve 4 Tx -ve Page 8 of 12

9 4. Electrical Input power is provided by the VMC and the power requirements of this module is consistent with the power provided by both MDB and Executive protocol machines. Power is provide for both protocols via CONN1. In the event that an external power supply is required (e.g. for servicing) an v / 1.2 Amps, AC or DC. PSU can be used. Page 9 of 12

10 5. Case 5.1 Removal Retaining Screw (m3x8) Figure Remove case retaining screw (see Figure 5.1) Lift front of case upwards and slide off backwards. N.B The internal executive data cable that links CONN2 & CONN5(ref. Figs. 2.2/2.3) must be disconnected from CONN2 before the case can be fully removed. Page 10 of 12

11 5.2 Assembly 1. Locate in slot Case Slot 2. Rotate Case into position Figure 5.2 Figure Locate the tip front edge of the case into the case slot of the front plate (see Figure 5.2 above). The case must be inserted at an angle (see Figure 5.3) such that the rear of the case is raised above the top of the front plate, such that the XPort network and the MDB sockets (see Figure 2.3) are below the relevant cutouts in the rear of the case, with approx. 20% of sockets visible Rotate the case into position (see Figure 5.3), it may be necessary at the same time to lift up the network & MDB sockets so that they snap into the case cutouts Screw in the case retaining screw see Figure 5.1 Page 11 of 12

12 6. Change Control Version Date Comment A 10/07/05 Started B 29/07/2005 Amend cable 108 definition. C 26/08/2005 Add Section 5. Page 12 of 12