Hidex Modem Installation Guide

Transcription

1 GE Security Hidex Modem Installation Guide P/N A ISS 17DEC07

2 Copyright Copyright 2007 GE Security, Inc. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from GE Security, Inc., except where specifically permitted under U.S. and international copyright law. Document number: A Disclaimer The information in this document is subject to change without notice. GE Security, Inc. ( GE Security ) assumes no responsibility for inaccuracies or omissions and specifically disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence, directly or indirectly, of the use or application of any of the contents of this document. For the latest documentation, contact your local supplier or visit us online at Approvals - modem module Safety Certifications UL60950 cul60950 EN60950 IEC60950 ACA TS001/AS 3260 CCC This publication may contain examples of screen captures and reports used in daily operations. Examples may include fictitious names of individuals and companies. Any similarity to names and addresses of actual businesses or persons is entirely coincidental. EMC Approvals FCC Part 15 Canadian EMC EN55022 EN55024 GB4943, GB9254 Compliance to Global Telephone Standards Hidex II modems have passed the following homologation: FCC Part 68 FCC Part 15 IC-CSO3 ETSI TS , 2, 3 v (originally CTR21) ESD

3 Content Content i Before you begin 1 Picture Perfect 2 Host, modem configuration, and programming 2 Controller parameter block, modem configuration, and programming 3 Secure Perfect 6.1.1/FCWnx 4 Host Modem Configuration 4 Controller Modem Configuration 6 RS-232 Communication Cable Overview 7 Hidex Modem Setup Instructions i

4

5 Before you begin Before you proceed, make sure that your peripheral system hardware (such as controllers, readers, and network lines) are installed and running. Use a standard, straight-through PC-to-modem cable that includes TxD, RxD, RTS, CTS, DSR, DCD, DTR, RI, and ground. The setup of the Hidex modem depends on the product you are using with this modem. This document includes the following sections: Picture Perfect - refer to "Picture Perfect" on page 2. Secure Perfect - Refer to "Secure Perfect 6.1.1/FCWnx" on page 4. RS-232 Communication Cable Overview - Refer to "RS-232 Communication Cable Overview" on page 7. Hidex Modem Setup Instructions 1

6 Picture Perfect Picture Perfect In Picture Perfect, controllers are allowed only one modem type. Controllers call only those host modems that are of the same modem type. The Hidex host port modem can communicate with the following internal modems for Picture Perfect: PXNplus internal modem DirecDoor internal modem The following are not compatible with the Hidex modems for Picture Perfect: PX controller PXN controller Host, modem configuration, and programming To configure the host port modem: 1. If this is the first time you are adding a Hidex modem to the host, you will need to create a Hidex modem record; otherwise, go to step Within Picture Perfect, select Devices, then Modems (if the Hidex selection is not an available option). Find the Hayes 9600 record. Click New, then Copy. Change the description to Hidex. 3. Change the Initialization and Deinitialization fields to read: ATE0X3V1&C1&D2S0=1S7=60&Q5&W 4. Click Save. 5. Select Devices, then Ports. Create the port to which this modem will be attached. 6. Set the Baud to 9600, Data bits to 8, Parity to None and Stop bits to 1. Assign Modem Type (Hidex) to this port. To configure the controller internal modem: 1. Select Devices, then Micros. Find the controllers that will communicate with this new modem. 2. Select Dial-Up, then Modem Type and choose the Hidex modem record that matches the Hidex. 3. Click Save, then Quit. 2 Hidex Modem Setup Instructions

7 Picture Perfect Table 1: Host modem configuration Baud Rate Initialization/Deinitialization Strings Minimum controller firmware version R112 or higher Hidex Baud Rate 9600 Init: ATE0X3V1&C1&D2S0=1S7=60&Q5&W Deinit: ATE0X3V1&C1&D2S0=1S7=60&Q5&W Controller parameter block, modem configuration, and programming To configure the controller internal modem when using a Hidex modem at the host: The host phone number(s), the controller address, and the modem initialization/deinitialization strings may be programmed into the parameter block of the controller using the Integrated Configuration Tool (ICT). Install the internal plug in modem on the controller, and then reset the controller. Table 2: PXNplus/DirecDoor Modem Configuration for Picture Perfect Baud Rate Initialization/Deinitialization Strings Minimum controller firmware version R112 or higher Hidex Baud Rate 9600 Init: ATE0X3V1&C1&D2S0=1S7=60&Q5 Deinit: ATE0X3V1&C1&D2S0=1S7=60&Q5 To set dial-up parameters and power on: 1. The PXNplus and DirecDoor controllers do not require dip switch settings for dial-up communications. Utilize the Integrated Configuration Tool (ICT) to set the required dial-up parameters. 2. The controller makes a dial-up connection to the host. Hidex Modem Setup Instructions 3

8 Secure Perfect 6.1.1/FCWnx Secure Perfect 6.1.1/FCWnx The following modems are compatible with the Hidex Modems for Secure Perfect: PXNplus internal modem DirecDoor internal modem Host Modem Configuration To begin the installation: 1. Click Start, Settings, then Control Panel. 2. Double-click the Modems icon (Phone and Modem Options). 3. Select the Modems tab. 4. Click Add. The Install New Modem dialog displays. 5. Select Don t detect my modem; I will select it from a list. 6. Click Next. 7. Select Standard Modem Types from the Manufacturers list. 8. Select Standard 9600bps Modem from the Models list. 9. Click Next. 10. Select communications port. 11. Click Next. 12. Click Finish. 4 Hidex Modem Setup Instructions

9 Secure Perfect 6.1.1/FCWnx To set the properties: 1. In the Modems tab, select Standard 9600 bps modem. 2. Select Properties. 3. For Windows XP, on the Modem tab, select the following: Maximum Port Speed 9600 To configure at 4800, select Maximum Port Speed 4800 To configure at 2400, select Maximum Port Speed For Windows 2000, on the General tab, select the following: Maximum Port Speed 9600 To configure at 4800, select Maximum Port Speed 4800 To configure at 2400, select Maximum Port Speed Select the Advanced tab. 6. In the Advanced window, under Extra Initialization Commands, enter ATE0X3V1&C1&D2S7=60&Q5&W. 7. Click Change Default Parameters, then select the Advanced tab. Select the following: Data bits 8 Parity None Stop bits 1 8. Click Ok twice, then Close. Hidex Modem Setup Instructions 5

10 Secure Perfect 6.1.1/FCWnx Controller Modem Configuration To configure the PXNplus/DirecDoor controllers internal modem when using a Hidex modem at the host: The host phone number(s), the controller address, and modem initialization/deinitialization strings must be programmed into the parameter block of the controller using the Integrated Configuration Tool (ICT). Attach the controller to the modem, and then reset the controller. Table 3: PXNplus/DirecDoor Modem Configuration for Secure Perfect/FCWnx Baud Rate Initialization/Deinitialization Strings Minimum controller firmware version R112 or higher Hidex Baud Rate 2400, 4800, 9600 Init: ATE0X3V1&C1&D2S0=1S7=60&Q5 Deinit: ATE0X3V1&C1&D2S0=1S7=60&Q5 6 Hidex Modem Setup Instructions

11 RS-232 Communication Cable Overview RS-232 Communication Cable Overview Figures 4 and 5 show the connections for the various types of host connectors. Figure 4: Host-to-Modem Connection Overview Figure 5: Host-to-Modem Cable Pinouts DB25M DB9F DB25M DB25F TxD 2 RxD 3 RTS 4 CTS 5 DSR 6 GND 7 DCD 8 DTR 20 RI 22 3 TxD 2 RxD 7 RTS 8 CTS 6 DSR 5 GND 1 DCD 4 DTR 9 RI TxD 2 RxD 3 RTS 4 CTS 5 DSR 6 GND 7 DCD 8 DTR 20 RI 22 2 TxD 3 RxD 4 RTS 5 CTS 6 DSR 7 GND 8 DCD 20 DTR 22 RI Dial-up Modem PC/Pentium Dial-up Modem RISC, XT, PS/2, Digi Board Hidex Modem Setup Instructions 7

12 RS-232 Communication Cable Overview 8 Hidex Modem Setup Instructions