VIDEOJET connect 7000

Transcription

1 VIDEOJET connect 7000 VJC en Operation Manual

2

3 VIDEOJET connect 7000 Table of Contents en 3 Table of contents 1 Browser connection System requirements Establishing the connection Password protection in camera Protected network 7 2 System overview Live page Playback Settings 8 3 Control of Connected Devices System Requirements Configuration Overview 10 4 General settings Identification Naming ID iscsi Initiator extension Password Enter Password Confirm password Date/Time Date format Device date / Device time Device time zone Daylight saving time Time server IP address Time server type 13 5 Web Interface Appearance Website language Company logo Device logo Show VCA metadata Show VCA trajectories Show overlay icons Select video player JPEG size, interval and quality LIVE Functions Transmit audio Show alarm inputs Show alarm outputs Show event log Show system log Logging Save event log Save system log 15 Bosch Security Systems Operation Manual Operation Manual

4 4 en Table of Contents VIDEOJET connect Transcoder Transcoder Setup Device [number] Name Password Http port, Https port Configure Router Transcoder Profile Profile name Maximum bit rate Transcoding interval Video resolution I-frame distance Min. P-frame QP I/P-frame delta QP Audio 18 7 Recording Storage Management Device manager Recording media Activating and configuring storage media Formatting storage media Deactivating storage media Remote Video Device Status Last error Recording target Bit rate Initialize Recording Start Recording Stop Recording 21 8 Alarm Alarm Task Editor 22 9 Network Network Access Automatic IP assignment IP V4 address IP V6 address DNS server address Video transmission HTTP browser port HTTPS browser port RCP+ port Telnet support Interface mode PoE Interface mode ETH Interface mode ETH Network MSS [Byte] iscsi MSS [Byte] Operation Manual Operation Manual Bosch Security Systems

5 VIDEOJET connect 7000 Table of Contents en Network MTU [Byte] DynDNS Enable DynDNS Provider Host name User name Password Force registration now Status Advanced Cloud-based Services RTSP port Authentication (802.1x) Network Management SNMP UPnP Quality of Service Accounts IPv4 Filter Encryption Service Installer Menu Reboot device Factory defaults Maintenance Update server Firmware Upload History Configuration Maintenance log Licenses System Overview Operation via the browser Live page LIVE page overview Digital I/O System Log / Event Log Recording status Storage, CPU and network status Status icons IP Address of Connected Devices Playback Selecting recordings for playback Exporting tracks Searching for tracks Controlling playback Operation Configure VIDEOJET connect 7000 to Operate with a MIC7000 Camera Configure Alarm Inputs and Outputs 36 Bosch Security Systems Operation Manual Operation Manual

6 6 en Table of Contents VIDEOJET connect Configure Audio Configure Video Playback Operation Manual Operation Manual Bosch Security Systems

7 VIDEOJET connect 7000 Browser connection en 7 1 Browser connection A computer with Microsoft Internet Explorer is used to receive live images, control the unit, and replay stored sequences. The unit is configured over the network using the browser. 1.1 System requirements Network access (Intranet or Internet) Microsoft Internet Explorer version 9 (32-bit) Screen resolution at least pixels 16- or 32-bit color depth JVM installed The Web browser must be configured to enable Cookies from the IP address of the unit. In Windows Vista, deactivate protected mode on the Security tab under Internet Options. To play back live video images, an appropriate ActiveX must be installed on the computer. If necessary, install Bosch Video Client. This can be downloaded from the following address: Establishing the connection The unit must have a valid IP address to operate on your network and a compatible subnet mask. By default, DHCP is pre-set at the factory to On and so your DHCP server assigns an IP address. With no DHCP server the default address is Start the Web browser. 2. Enter the IP address of the unit as the URL. 3. During initial installation, confirm any security questions that appear. Note: If you cannot connect, the unit may have reached its maximum number of connections. Depending on the device and network configuration, each unit can have up to 50 web browser connections, or up to 100 connections via Bosch Video Client or Bosch Video Management System Password protection in camera A unit offers the option of limiting access across various authorization levels. If the unit is password-protected, a message to enter the password appears. 1. Enter the user name and the associated password in the appropriate fields. 2. Click OK. If the password is correct, the desired page is displayed. Protected network If a RADIUS server is used for network access control (802.1x authentication), the unit must be configured first. To configure the unit, connect it directly to a computer using a network cable and configure the two parameters, Identity and Password. Only after these have been configured can communication with the unit via the network occur. Bosch Security Systems Operation Manual Operation Manual

8 8 en System overview VIDEOJET connect System overview When a connection is established, the LIVE page is initially displayed. The application title bar displays three items: LIVE, PLAYBACK, SETTINGS. Note: The PLAYBACK link is only visible if a storage medium has been configured for recording. (With VRM recording this option is not active.) 2.1 Live page The LIVE page is used to display the live video stream and control the unit. 2.2 Playback The PLAYBACK page is used for playing back recorded sequences. 2.3 Settings The SETTINGS page is used to configure the unit and the application interface Operation Manual Operation Manual Bosch Security Systems

9 VIDEOJET connect 7000 Control of Connected Devices en Control of Connected Devices System Requirements The camera requires specific software and hardware to allow a user to view live images and to configure camera settings over a TCP/IP network. These requirements are: A computer with the Microsoft Windows XP, Vista, or Windows 7 operating system, network access, and the Microsoft Internet Explorer Web browser version 8.0 or later, or A computer with Microsoft Windows XP, Vista, or Windows 7 operating system, network access, and reception software such as the Bosch Video Management System or the Video Client, or other third party head-end video management software, or A compatible hardware decoder from Bosch Security Systems connected to a video monitor. Notice! The Web browser must be configured to enable Cookies to be set from the IP address of the unit. In Windows 7, deactivate protected mode on the Security tab under Internet Options. You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer. In Windows Vista, deactivate protected mode on the Security tab under Internet Options. You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer. If you choose to use a computer running Microsoft Internet Explorer or any of the Bosch software, the computer must conform to the following minimum requirements: Operating System: Windows XP (Service Pack 3) or Windows 7 (32 or 64 bits) Processor: Intel Pentium Quad Core, 3.0 GHz or comparable RAM: 2048 MB Free Hard Disk Space: 10 GB Video system: NVIDIA GeForce 8600 or higher display with a minimum of 16-bit color Network interface: 100/1000-BaseT Software: Microsoft Internet Explorer, version 8.0 or higher Video Client DirectX 9.0c Oracle Java Virtual Machine 1.6.0_26 or newer The camera includes the means to decode the video via a web browser; however, for more advanced features such as local recording to PC, snapshot, and full screen display, you must obtain MPEG-ActiveX. For the latest versions of the Video Client, DirectX, Oracle Java Virtual Machine, and MPEG- ActiveX software, go to navigate to the product page for your camera, and then download the software from the Software tab. Notice! Ensure that the graphics card is set to 16-bit or 32-bit color. If you need further assistance, contact your PC system administrator. Bosch Security Systems Operation Manual Operation Manual

10 10 en Control of Connected Devices VIDEOJET connect Configuration Overview When a connection is established, the LIVE page is initially displayed. The application title bar displays three items: LIVE, PLAYBACK, SETTINGS. Note: The PLAYBACK link is only visible if a storage medium has been configured for recording. (With VRM recording this option is not active.) The LIVE page is used to display the live video stream and control the unit. The PLAYBACK page is used for playing back recorded sequences. The SETTINGS page is used to configure the unit and the application interface Operation Manual Operation Manual Bosch Security Systems

11 VIDEOJET connect 7000 General settings en General settings Identification Naming Assign a unique name to assist in identification. This name simplifies the management of multiple devices in more extensive systems. The name is used for remote identification, for example, in the event of an alarm. Choose a name that makes it as easy as possible to identify the location unambiguously. You can use additional lines to enter kanji characters. 1. Click the + sign to add a new line 2. Click the icon next to the new line. A window with a character map opens. 3. Click the required character. The character is inserted into the Result field. 4. In the character map, click the << and >> icons to move between the different pages of the table, or select a page from the list field. 5. Click the < icon to the right of the Result field to delete the last character, or click the X icon to delete all characters. 6. Click the OK button to apply the selected characters to the new line of the name. The window closes. ID Each device should be assigned a unique identifier that can be entered here as an additional means of identification. iscsi Initiator extension Add text to an initiator name to make identification easier in large iscsi systems. This text is added to the initiator name, separated from it by a full stop. (You can see the initiator name in the System Overview page.) Password A password prevents unauthorized access to the device. You can use different authorization levels to limit access. Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. Therefore, you always have to start from the highest authorization level when assigning passwords. You can define and change a password for each authorization level if you are logged in as service or if the unit is not password protected. Enter the password for the appropriate authorization level here. The maximum password text length is 19 characters and no special characters are allowed. The device has three authorization levels: service, user, and live. service is the highest authorization level. Entering the correct password gives access to all the functions and allows all configuration settings to be changed. user is the middle authorization level. At this level you can operate the device, play back recordings, and also control camera, for example, but you cannot change the configuration. live is the lowest authorization level. At this level you can only view the live video image and switch between the different live image displays. Bosch Security Systems Operation Manual Operation Manual

12 12 en General settings VIDEOJET connect Enter Password Define and change a separate password for each level. Enter the password (19 characters maximum; no special characters) for the selected level. Confirm password Re-enter the new password to ensure that there are no typing mistakes. Date/Time Date format Select the required date format. Device date / Device time If there are multiple devices operating in your system or network, it is important to synchronize their internal clocks. For example, it is only possible to identify and correctly evaluate simultaneous recordings when all devices are operating on the same time. 1. Enter the current date. Since the device time is controlled by the internal clock, it is not necessary to enter the day of the week it is added automatically. 2. Enter the current time or click Sync to PC to apply the system time from your computer to the device. Note: It is important that the date/time is correct for recording. An incorrect date/time setting could prevent correct recording Device time zone Select the time zone in which the system is located. Daylight saving time The internal clock can switch automatically between normal and daylight saving time (DST). The unit already contains the data for DST switch-overs for many years in advance. If the date, time and zone have been set up correctly, a DST table is automatically created. If you decide to create alternative daylight saving time dates by editing the table, note that values occur in linked pairs (DST start and end dates). First, check the time zone setting. If it is not correct, select the appropriate time zone and click Set. 1. Click Details to edit the DST table. 2. Select the region or the city which is closest to the system's location from the list box below the table. 3. Click Generate to fill the table with the preset values from the unit. 4. Click one of the entries in the table to make changes. The entry is highlighted. 5. Click Delete to remove the entry from the table. 6. Choose other values from the list boxes under the table, to change the selected entry. Changes are immediate. 7. If there are empty lines at the bottom of the table, for example after deletions, add new data by marking the row and selecting values from the list boxes. 8. When finished, click OK to save and activate the table Operation Manual Operation Manual Bosch Security Systems

13 VIDEOJET connect 7000 General settings en Time server IP address The unit can receive the time signal from a time server using various time server protocols and then use it to set the internal clock. The device polls the time signal automatically once every minute. Enter the IP address of a time server. Time server type Select the protocol that is supported by the selected time server. It is recommended to select the SNTP server protocol. This protocol provides high accuracy and is required for special applications and future function extensions. Select Time server if the server uses the RFC 868 protocol. Bosch Security Systems Operation Manual Operation Manual

14 14 en Web Interface VIDEOJET connect Web Interface Appearance You can adapt the appearance of the web interface and change the website language to meet your requirements. GIF or JPEG images can be used to replace the company and device logos. The image can be stored on a web server (for example, Ensure that a connection to the web server is always available to display the image. The image files are not stored on the unit. To restore the original graphics, delete the entries in the Company logo and Device logo fields Website language Select the language for the user interface. Company logo To replace the company's logo in the top-right part of the window, enter the path to a suitable image in this field. The image file must be stored on a web server. Device logo To replace the device name in the top-left part of the window, enter the path to a suitable image in this field. The image file must be stored on a web server. Show VCA metadata When video analysis is activated, additional information from the video content analysis (VCA) function is displayed in the live video image. With the MOTION+ analysis type, for example, the sensor fields in which motion is recorded are marked with rectangles. Show VCA trajectories The trajectories (motion lines of objects) from the video content analysis are displayed in the live video image if a corresponding analysis type is activated. Show overlay icons When selected, various status icons are displayed as an overlay on the video images. Select video player Select the type of player to be used for live mode viewing. JPEG size, interval and quality Select the size, update interval and quality of the M JPEG image displayed on the livepage. The highest quality is 1. When Best possible is selected for size, the unit determines the quality based on the network capacity. LIVE Functions You can adapt the LIVE page functions to meet your requirements. Choose from a variety of different options for displaying information and controls. 1. Select the check boxes for the functions to be displayed on the LIVE. The selected elements are checked. 2. Check to see if the desired items are shown Operation Manual Operation Manual Bosch Security Systems

15 VIDEOJET connect 7000 Web Interface en Transmit audio When selected, the audio from the camera (if set to On on the Audio page) is sent to the computer. This setting applies only to the computer on which the selection is made. Transmitting audio data requires additional network bandwidth. Show alarm inputs The alarm inputs are displayed next to the video image as icons along with their assigned names. If an alarm is active, the corresponding icon changes color. Show alarm outputs Alarm outputs are shown next to the video image as icons along with their assigned names. If an output is switched, the icon changes color. Show event log The event messages are displayed with the date and time in a field next to the video image. Show system log The system messages are displayed with the date and time in a field next to the video image and provide information about the establishment and termination of connections, and other system-level messages. Logging Save event log Select this option to save event messages in a text file on the local computer. This file can be viewed, edited, and printed with any text editor or standard office software. File for event log Enter the path for saving the event log. If necessary, click Browse... to find a suitable folder. Save system log Select this option to save system messages in a text file on the local computer. This file can be viewed, edited, and printed with any text editor or standard office software. File for system log Enter the path for saving the system log. If necessary, click Browse... to find a suitable folder. Bosch Security Systems Operation Manual Operation Manual

16 16 en Transcoder VIDEOJET connect Transcoder Transcoder Setup Define up to four cameras for which you want to offer transcoded video. Transcoding is only available for recorded video. Therefore, make sure that these cameras will have recordings, either by configuring the cameras accordingly or by having the transcoder managing it. For information, the HTTP and HTTPS port of the transcoder are displayed Device [number] Notice! If a MIC7000 camera is assigned to Camera 1, it becomes bound to the alarm I/O functions and the washer functions provided by the VIDEOJET connect 7000 device. 4 Click a drop-down box. The system scans for available cameras which are listed for selection. This includes analog cameras which are integrated into your system through a single-channel encoder. In this case, the corresponding encoder is listed for selection. 4 Select the desired camera from the list. The parameters Type, MAC, and Name are displayed, if available Name 4 Change the name if desired. Do not use any special characters, for example &, in the name. Special characters are not supported by the system's internal management. Note that the name here is only used for the transcoder operation. Changes here will not overwrite the name assigned to the camera or to the encoder on the corresponding SETTINGS page of the respective unit. The name that you enter here will be displayed in the title bar of the transcoder Web pages and in the list of available cameras on the PLAYBACK page. If you leave the field empty, the IP address of the unit is displayed. Password 4 In the field Password, enter the service password of the selected camera. Http port, Https port By default, the numbers HTTP port and HTTPS port for the camera are set automatically for each camera as an offset to the transcoder ports. The corresponding fields are marked by the white outline and the highlighted connection line. You may change the numbers, if necessary, on the page Network Access. 4 Repeat the procedure for each camera that you want to add. 4 Click Set to save the settings. For each connected camera a link is added in the title bar next to the SETTINGS link stating the camera number 1 to 4 and its name or IP address. Configure Router 4 If your router has UPnP enabled, click Configure Router to save the settings to the router. Otherwise, configure your router manually. The cameras are now available for selection on the PLAYBACK page. Transcoding will only be possible once recordings for the cameras are available Operation Manual Operation Manual Bosch Security Systems

17 VIDEOJET connect 7000 Transcoder en Transcoder Profile Profile name Select the desired resolution for the standard definition video image. Note: These resolutions are not used by a HD stream. IP Profiles (Configuration Parameters) Profile Target bit rate Maximum bit rate Encoding interval High resolution kbps 4000 kbps ips High resolution kbps 3000 kbps ips Low bandwidth 700 kbps 1500 kbps ips DSL 400 kbps 500 kbps ips ISDN (1B) 40 kbps 50 kbps ips Modem 20 kbps 22 kbps ips GSM 7 kbps 8 kbps ips If required, enter a new name for the profile Maximum bit rate This maximum data rate is not exceeded under any circumstances. Depending on the video quality settings for the I-frames and P-frames, this can result in individual images being skipped. The value entered here must be at least 10% higher than the value entered in the Target bit rate field. If the value entered here is too low, it is automatically adjusted. Transcoding interval This parameter determines the interval at which images are encoded and transmitted. For example, entering or selecting 4 means that only every fourth image is encoded, while the following there are skipped, which can be particularly advantageous for networks with low bandwidths. The image rate in (images per second (ips) appears next to the text field or slider. Video resolution Video resolution Select the desired resolution for the video image. I-frame distance I-frame distance This parameter allows you to set the intervals in which the I-frames will be coded. Auto means auto mode, whereby the video server inserts I-frames as necessary. Values range from 3 to 60. An entry of 3 indicates that I-frames are continuously generated. An entry of 4 indicates that only every fourth image is an I-frame, and so on; the frames in between are coded as P-frames. Note that the values supported depend on the GOP structure setting. For example, only even values are supported with IBP; if you have selected IBBP, only 3 or multiples of 3 are supported. Bosch Security Systems Operation Manual Operation Manual

18 18 en Transcoder VIDEOJET connect Min. P-frame QP Min. P-frame QP This parameter allows you to adjust the image quality of the P-frame and to define the lower limit for the quantization of the P-frames, and thus the maximum achievable quality of the P- frames. In the H.264-protocol, the Quantization Parameter (QP) specifies the degree of compression and thus the image quality for every frame. The lower the quantization of the P- frame (QP value), the higher the encoding quality (and thus the best image quality) and the lower the frame refresh rate depending on the settings for the maximum data rate under network settings. A higher quantization value results in low image quality and lower network load. Typical QP values are between 18 and 30. The basic setting Auto automatically adjusts the quality to the settings for the P-frame video quality. I/P-frame delta QP I/P-frame delta QP This parameter sets the ratio of the I-frame quantization (QP) to the P-frame quantization (QP). For example, you can set a lower value for I-frames by moving the slide control to a negative value. Thus, the quality of the I-frames relative to the P-frames is improved. The total data load will increase, but only by the portion of I-frames. The basic setting Auto automatically adjusts to the optimum combination of movement and image definition (focus). To obtain the highest quality at the lowest bandwidth, even in the case of increased movement in the picture, configure the quality settings as follows: 1. Observe the coverage area during normal movement in the preview images. 2. Set the value for Min. P-frame QP to the highest value at which the image quality still meets your needs. 3. Set the value for I/P-frame delta QP to the lowest possible value. This is how to save Audio bandwidth and memory in normal scenes. The image quality is retained even in the case of increased movement since the bandwidth is then filled up to the value that is entered under Maximum bit rate. Input volume You can set the input volume with the slider (from 0 to 31, with 0 as the default) Operation Manual Operation Manual Bosch Security Systems

19 VIDEOJET connect 7000 Recording en 19 7 Recording Images can be recorded to an appropriately configured iscsi system or, for devices with an SD slot, locally to an SD card. SD cards are the ideal solution for shorter storage times and temporary recordings. They can be used for local alarm recording or to improve the overall reliability of video recording. For long-term authoritative images use an appropriately sized iscsi system. Two recording tracks are available (Recording 1 and Recording 2). The encoder streams and profiles can be selected for each of these tracks for both standard and alarm recordings. Ten recording profiles are available where these recording tracks can be defined differently. These profiles are then used for building schedules. A Video Recording Manager (VRM) can control all recording when accessing an iscsi system. The VRM is an external program for configuring recording tasks for video servers. For further information, contact your local customer service at Bosch Security Systems Storage Management Device manager An external Video Recording Manager (VRM) system for the unit is configured via the Configuration Manager. The Managed by VRM box is only an indicator; it cannot be changed here. If the Managed by VRM box is checked, you are not able to configure any further recording settings on this page. Recording media Select a media tab to connect to the available storage media. iscsi Media To use an iscsi system as the storage medium, a connection to the desired iscsi system is required to set the configuration parameters. The storage system selected must be available on the network and completely set up. It must have an IP address and be divided into logical drives (LUNs). 1. Enter the IP address of the required iscsi destination in the iscsi IP address field. 2. If the iscsi destination is password protected, enter the password into the Password field. 3. Click Read. The connection to the IP address is established. The Storage overview field displays the logical drives. Local Media An SD card inserted in the camera can be used for local recording (not available on some cameras). 4 If the SD card is password protected, enter the password into the Password field. The Storage overview field displays the local media. Note: SD card recording performance is highly dependent on the speed (class) and performance of the SD card. An SD card of Class 6 or higher is recommended. Bosch Security Systems Operation Manual Operation Manual

20 20 en Recording VIDEOJET connect Activating and configuring storage media Available media or iscsi drives must be transferred to the Managed storage media list, activated, and configured for storage. Note: A iscsi target storage device can only be associated with one user. If a target is being used by another user, ensure that the current user no longer needs the target before decoupling that user. 1. In the Storage overview section, double-click a storage medium, an iscsi LUN or one of the other available drives. The medium is added as a target in the Managed storage media list. Newly added media is shown as Not active in the Status column. 2. Click Set to activate all media in the Managed storage media list. The Status column shows all media as Online. 3. Check the box in the Rec. 1 or Rec. 2 column to specify the recording tracks to be recorded on the target selected Formatting storage media All recordings on a storage medium can be deleted at any time. Check the recordings before deleting and back-up important sequences on the computer's hard drive. 1. Click a storage medium in the Managed storage media list to select it. 2. Click Edit below the list. 3. Click Format in the new window to delete all recordings in the storage medium. 4. Click OK to close the window. Deactivating storage media A storage medium in the Managed storage media list can be deactivated. It is then no longer used for recordings. 1. Click a storage medium in the Managed storage media list to select it. 2. Click Remove below the list. The storage medium is deactivated and removed from the list. Remote Video Device This page provides information on the current recording status of the cameras connected to VIDEOJET connect For easy identification, the IP address of the connected camera is the heading for each corresponding information block. The data in the fields in this window may be followed by an icon. Move the cursor over the icon to show more details about each field Status This field provides the status of the remote video device. Status descriptions include Offline, Recording, and Running. Last error This field identifies when the last error occurred on the remote video device. Recording target This field identifies the recording target for the respective camera. This target is also the source for the recordings available on the PLAYBACK page Operation Manual Operation Manual Bosch Security Systems

21 VIDEOJET connect 7000 Recording en Bit rate This field identifies the bit rate of the recording for the remote video device. Initialize Recording To configure VIDEOJET connect 7000 to manage recordings, you must initialize the recordings. 4 Click Initialize Recording for the respective device. The Configuration window appears. (To initialize recording for all connected devices at once, click Initialize All.) 4 Mark the Save Settings of the remote video device that you want to configure with the recording defaults of VIDEOJET connect Generally, this means that a simple basic configuration is set which grants you most effective recording that also supports forensic search: Select the desired Recording Profiles. Recording mode as it affects the defaults to be set. Note that only the Day tab on the Recording Profiles page is overwritten, that is the tab marked green. - Pre-alarm The best stream profile and the maximum pre-alarm time for RAM recording together with a minimum post-alarm time are selected, all available alarm triggers are activated, and metadata is included in recording. - Continuous The best stream profile is selected for recording, pre- and post-alarm times are deleted, all available alarm triggers are deactivated, and metadata is included in recording. Recording Scheduler The scheduler is set to 24/7 recording with the Day recording profile. VCA If the camera supports IVA software, this is set as analysis type and activated to detect any object in the scene. Otherwise, the motion detector is activated configured to monitor the entire area for even small objects with high sensitivity. Click Set to save the settings. The recording target is the one defined in the transcoder. Only recordings to this target will now be available on the PLAYBACK page. Start Recording Click this button to start the recording for a camera. Stop Recording Click this button to stop the recording for a camera. Bosch Security Systems Operation Manual Operation Manual

22 22 en Alarm VIDEOJET connect Alarm Alarm Task Editor Editing scripts on this page overwrites all settings and entries on the other alarm pages. This procedure cannot be reversed. To edit this page, you should have programming knowledge and be familiar with the information in the Alarm Task Script Language document and the English language. As an alternative to the alarm settings on the various alarm pages, enter the desired alarm functions in script form here. This will overwrite all settings and entries on the other alarm pages. 1. Click Examples under the Alarm Task Editor field to see some script examples. A new window opens. 2. Enter new scripts in the Alarm Task Editor field or change existing scripts in line with your requirements. 3. When finished, click Set to transmit the scripts to the device. If the transfer was successful, the message Script successfully parsed. is displayed over the text field. If it was not successful, an error message is displayed with further information Operation Manual Operation Manual Bosch Security Systems

23 VIDEOJET connect 7000 Network en 23 9 Network The settings on these pages are used to integrate the device into a network. Some changes only take effect after a reboot. In this case Set changes to Set and Reboot. 1. Make the desired changes. 2. Click Set and Reboot. The device is rebooted and the changed settings are activated. 9.1 Network Access If the IP address, subnet mask, or gateway address is changed, then the device is only available under the new addresses after the reboot Automatic IP assignment If the network has a DHCP server for the dynamic assignment of IP addresses, select On to automatically accept the DHCP-assigned IP address. For certain applications, the DHCP server must support the fixed assignment between IP address and MAC address, and must be appropriately set up so that, once an IP address is assigned, it is retained each time the system is rebooted. IP V4 address IP address Enter the desired IP address for the camera. The IP address must be valid for the network. Subnet mask Enter the appropriate subnet mask for the set IP address. Gateway address For the device to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise, this field can remain empty ( ). IP V6 address IP address Enter the desired IP address for the camera. The IP address must be valid for the network. Prefix length Enter the appropriate prefix length for the set IP address. Gateway address For the device to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise, this field can remain empty ( ). DNS server address The device is easier to access if it is listed on a DNS server. For example, to establish an Internet connection to the camera, it is sufficient to enter the name given to the device on the DNS server as a URL in the browser. Enter the DNS server's IP address. Servers are supported for secure and dynamic DNS. Video transmission If the device is used behind a firewall, TCP (Port 80) should be selected as the transmission protocol. For use in a local network, choose UDP. Multicast operation is only possible with the UDP protocol. The TCP protocol does not support multicast connections. Bosch Security Systems Operation Manual Operation Manual

24 24 en Network VIDEOJET connect HTTP browser port Select a different HTTP browser port from the list if required. The default HTTP port is 80. To limit connection to HTTPS, deactivate the HTTP port. To do this, activate the Off option. HTTPS browser port To limit browser access to encrypted connections, choose an HTTPS port from the list. The standard HTTPS port is 443. Select the Off option to deactivate HTTPS ports and limit connections to unencrypted ports. The camera uses the TLS 1.0 protocol. Ensure that the browser has been configured to support this protocol. Also ensure that Java application support is activated (in the Java Plugin Control Panel of the Windows Control Panel). To limit connections to SSL encryption, set the Off option in the HTTP browser port, the RCP+ port, and Telnet support. This deactivates all unencrypted connections allowing connections on the HTTPS port only. Configure and activate encryption for media data (video, audio, metadata) on the Encryption page. RCP+ port 1756 Activating RCP+ port 1756 allows unencrypted connections on this port. To allow only encrypted connections, set the Off option to deactivate the port. Telnet support Activating Telenet support allows unencrypted connections on this port. To allow only encrypted connections, set the Off option to deactivate telnet support, making telnet connections impossible. Interface mode PoE Select the type of Ethernet link for the interface for the camera bound to VIDEOJET connect 7000 (connected to the port labeled PoE on the PCBA of VIDEOJET connect 7000). Depending on the device connected, it may be necessary to select a special operation type. Options are: Auto 10 Mbps HD (half duplex) 10 Mbps FD (full duplex) 100 Mbps HD (half duplex) 100 Mbps FD (full duplex) Interface mode ETH 1 If necessary, select the type of Ethernet link for the interface for the device connected to the port labeled ETH 1 on the PCBA of VIDEOJET connect Depending on the device connected, it may be necessary to select a special operation type. Options are: Auto 10 Mbps HD (half duplex) 10 Mbps FD (full duplex) 100 Mbps HD (half duplex) 100 Mbps FD (full duplex) Note: Do not select a baud rate for this port unless a device is connected to this port on VIDEOJET connect Operation Manual Operation Manual Bosch Security Systems

25 VIDEOJET connect 7000 Network en Interface mode ETH 2 If necessary, select the type of Ethernet link for the interface for the device connected to the port labeled ETH 2 on the PCBA of VIDEOJET connect Depending on the device connected, it may be necessary to select a special operation type. Options are: Auto 10 Mbps HD (half duplex) 10 Mbps FD (full duplex) 100 Mbps HD (half duplex) 100 Mbps FD (full duplex) Note: Do not select a baud rate for this port unless a device is connected to this port on VIDEOJET connect Network MSS [Byte] Set the maximum segment size for the IP packet's user data here. This gives the option to adjust the size of the data packets to the network environment and to optimize data transmission. In UDP mode, comply with the MTU value set below. iscsi MSS [Byte] Specify a higher MSS value for a connection to the iscsi system than for the other data traffic via the network. The potential value depends on the network structure. A higher value is only useful if the iscsi system is located in the same subnet as the camera. Network MTU [Byte] Specify a maximum value in bytes for the package size (including IP header) to optimize data transmission. DynDNS Enable DynDNS A dynamic Domain Name Service (DNS) allows you to select the unit via the Internet using a host name, without having to know the current IP address of the unit. You can enable this service here. To do this, you must have an account with one of the dynamic DNS providers and you must register the required host name for the unit on that site. Note: For information about the service, registration process and available host names refer to the provider Provider Select your dynamic DNS Provider from the drop-down list. Host name Enter the host name registered for the unit. User name Enter the user name you registered. Password Enter the password you registered. Bosch Security Systems Operation Manual Operation Manual

26 26 en Network VIDEOJET connect Force registration now Force the registration by transferring the IP address to the DynDNS server. Entries that change frequently are not provided in the Domain Name System. It is a good idea to force the registration when setting up the device for the first time. Only use this function when necessary and no more than once a day, to avoid the possibility of being blocked by the service provider. To transfer the IP address of the device, click the Register button. Status The status of the DynDNS function is displayed here for information purposes; these settings cannot be changed. Advanced Cloud-based Services The Scene Mode determines how the camera communicates with Bosch Cloud-based Security and Services. For more information about these services and their availability, visit: Select Auto to allow the camera to poll the server a few times; if no contact is made, it stops polling. Select On to constantly poll the server. Select Off to block polling. RTSP port If necessary, select a different port for the exchange of the RTSP data from the list. The standard RTSP port is 554. Select Off to deactivate the RTSP function. Authentication (802.1x) To configure Radius server authentication, connect the unit directly to a computer using a network cable. If a Radius server controls access rights over the network, select On to activate authentication to communicate with the unit. 1. Enter the user name that the Radius server uses for the unit in the Identity field. 2. Enter the Password that the Radius server expects from the unit. Network Management SNMP The camera supports the SNMP V1 (Simple Network Management Protocol) for managing and monitoring network components, and can send SNMP messages (traps) to IP addresses. It supports SNMP MIB II in the unified code. If On is selected for the SNMP parameter and a SNMP host address is not entered, the device does not send the traps automatically and will only reply to SNMP requests. If one or two SNMP host addresses are entered, SNMP traps are sent automatically. Select Off to deactivate the SNMP function. SNMP host addresses To send SNMP traps automatically, enter the IP address of one or two target devices here. SNMP traps To choose which traps are sent: 1. Click Select. A dialog box appears. 2. Click the check boxes of the appropriate traps. 3. Click Set to close the window and send all of the checked traps Operation Manual Operation Manual Bosch Security Systems

27 VIDEOJET connect 7000 Network en UPnP Select On to activate UPnP communication. Select Off to deactivate it. When the Universal Plug-and-Play (UPnP) function is activated, the unit responds to requests from the network and is automatically registered on the requesting computers as a new network device. This function should not be used in large installations due to the large number of registration notifications. Note: To use the UPnP function on a Windows computer, both the Universal Plug-and-Play Device Host and the SSDP Discovery Service must be activated Quality of Service The priority of the different data channels can be set by defining the DiffServ Code Point (DSCP). Enter a number between 0 and 252 as a multiple of four. For alarm video you can set a higher priority than for regular video and you can define a Post Alarm Time over which this priority is maintained. Accounts Four separate accounts can be defined for posting and recording export. Type Select either FTP or Dropbox for the account type. Before using a Dropbox account ensure that the time settings of the device have been correctly synchronized. Account name Enter an account name to be shown as the target name. FTP server IP address For an FTP server, enter the IP address. FTP server login Enter your login name for the account server. FTP server password Enter the password that gives access to the account server. Click Check to confirm that it is correct. Path on FTP server Enter an exact path to post the images on the account server. Click Browse... to browse to the required path. Maximum bit rate Enter the maximum bit rate in kbps that will be allowed when communicating with the account. 9.6 IPv4 Filter To restrict the range of IP addresses within which you can actively connect to the device, fill-in an IP address and mask. Two ranges can be defined. 4 Click Set and confirm to restrict access. If either of these ranges are set, no IP V6 addresses are allowed to actively connect to the device. The device itself may initiate a connection (for example, to send an alarm) outside the defined ranges if it is configured to do so. Bosch Security Systems Operation Manual Operation Manual

28 28 en Network VIDEOJET connect Encryption If an encryption license is installed, this submenu gives access to the encryption parameters Operation Manual Operation Manual Bosch Security Systems

29 VIDEOJET connect 7000 Service en Service Installer Menu Reboot device Click Reboot to restart the camera. Factory defaults Click Defaults to restore the factory defaults for the camera. A confirmation screen appears. Allow several seconds for the camera to optimize the picture after a reset. Maintenance Notice! Before starting a firmware update, make sure to select the correct upload file. Do not interrupt the firmware installation. Even changing to another page or closing the browser window leads to interruption. Uploading the wrong files or interrupting the upload can result in the device no longer being addressable, requiring it to be replaced. The camera functions and parameters can be updated by uploading new firmware. To do this, the latest firmware package is transferred to the device via the network. The firmware is installed there automatically. Thus, a camera can be serviced and updated remotely without requiring a technician to make changes to the device on site. The latest firmware can be obtained from your customer service center or from the Bosch Security Systems download area Update server The address of the Bosch update server appears in the address box. 1. Click Check to make a connection to this server. 2. Select the appropriate version for your camera to download the firmware from the server. Firmware To update the firmware: 1. First, store the firmware file on your hard disk. 2. Enter the full path for the firmware file in the field or click Browse... to locate and select the file. 3. Click Upload to begin transferring the file to the device. The progress bar allows monitoring of the transfer. The new firmware is unpacked and the Flash memory is reprogrammed. The time remaining is shown by the message going to reset Reconnecting in... seconds. When the upload is completed successfully, the device reboots automatically. If the operating status LED lights up red, the upload has failed and must be repeated. To perform the upload, switch to a special page: 1. In the address bar of your browser, enter /main.htm after the device IP address, for example: /main.htm 2. Repeat the upload. Bosch Security Systems Operation Manual Operation Manual

30 30 en Service VIDEOJET connect Upload History Click Show to view the firmware upload history. Configuration Save configuration data for the device to a computer and load saved configuration data from a computer to the device. To load configuration data from the computer to the device: 1. Click Load From... ; a dialog box appears. Make certain that the file to be loaded comes from the same device type as the device to be reconfigured. 2. Locate and open the desired configuration file. The progress bar allows monitoring of the transfer. To save the camera settings: 1. Click Save As...; a dialog box appears. 2. Enter a file name if required and save Maintenance log Download an internal maintenance log from the device to send it to Customer Service for support purposes. Click Save As...and select a storage location for the file. Licenses This window is for the activation of additional functions by entering activation codes. An overview of installed licenses is shown. The installation code of the unit is also displayed here System Overview This window is for information only and cannot be modified. Keep this information at hand when seeking technical support. Select the text on this page with a mouse and copy it so that it can be pasted into an if required Operation Manual Operation Manual Bosch Security Systems