RoadRunner 24AP(i+) Recovering Tool Instructions
|
|
- Patricia Robinson
- 5 years ago
- Views:
Transcription
1 RoadRunner 24AP(i+) Recovering Tool Instructions Ver. 1.0
2 Follow these instructions if your modem do not boot. If you have questions or problems using this modem build in recovering tool, please contact A-Link technical support; by phone: (2.67 / min + local network fee) or techsupport@a-link.com 1. Download firmware update package from A-link website and unzip it to your computer. It is same firmware package used with update via web management. 2. To get modem recovery state, you should have IP addresses configured manually to your computer. Below instructions for different operating systems: Windows 2000/XP 1. Go to Start -> Settings -> Network and Dial-Up Connections 2. Move mouse over Local Area Connection icon and press right hand 3. Choose Internet Protocol (TCP/IP) -> Press Properties 4. Choose Use the following IP address 5. Add IP-address , subnet mask and gateway Leave Preferred DNS server and Alternate DNS server blank 7. When all necessary TCP/IP settings are done, press OK. In Network settings, press OK also (If windows needs to be restarted, press Yes) Windows Vista 1. Go to Start -> Network. 2. Press Network and Sharing Center button and then press Manage network connections link. 3. Move mouse over Local Area Connection icon and press right hand 4. Choose Internet protocol version 4 (TCP/IPv4) -> Press Properties. 5. Choose Use the following IP address 6. Add IP-address , subnet mask and gateway Leave Preferred DNS server and Alternate DNS server blank 8. In properties of Internet Protocol (TCP/IP), press OK. 9. Press OK in Network settings. Mac OS 1. Open AppleTalk -controller, choose Ethernet connection 2. Open TCP/IP -controller and modify these settings: Connection = Ethernet : Definition = Manual IP-address = Subnet mask = Gateway = Save settings. Linux RedHat Open Start Here from desktop, go to System Settings and Network. 2. In Devices, double click mouse s left hand button on top of your Network adapter and modify these settings: Choose Statically set IP addresses: Address = Subnet Mask = Default Gatevay Address = Press Ok.
3 3. Make sure that you modem have power off and you have Ethernet cable connected between modem and computer.. 4. Press reset button back side of the modem with pen or needle. Keep pressing it. 5. Turn power on to modem and press reset button until modem PPP and WL/ACT led s has been flashed 5 times. 6. After you have released the reset button (PPP and WL/ACT led s keep flashing), modem is in recovery state and you can access to recovery website with your web browser. 7. Press Browse button on recovery website and find firmware image file (rr24api+_vxxx.bin) saved on your computer and press Open.
4 8. Press APPLY button to start recover progress. 9. Press OK for all above questions. 10. Wait few minutes while modem recovers the firmware. Do NOT turn off modem during recovery process.
5 11. After recovering process finished, press Reboot button on left side of web page. 12. Press RESET button to reboot modem on normal operation state. 13. Press OK for all above questions.
6 14. Please wait few minutes when modem reboots. 15. When login screen appears, modem has been recovered successfully and you can change your computer network settings to get IP addresses automatically. Next page are instructions for different operating systems.
7 Windows 2000/XP 1. Go to Start -> Settings -> Network and Dial-Up Connections 2. Move mouse over Local Area Connection icon and press right hand 3. Choose Internet Protocol (TCP/IP) -> Press Properties 4. Choose Obtain an IP address automatically 5. When all necessary settings have been made, press OK. 6. In properties of Internet Protocol (TCP/IP), press OK. 7. Press OK in Network settings. (If windows need to be restarted, press Yes) 8. Make sure that, no Proxy settings is enabled in Internet Explorer settings 9. Now your workstation is ready for Internet Windows Vista 1. Go to Start -> Network. 2. Press Network and Sharing Center button and then press Manage network connections link. 3. Move mouse over Local Area Connection icon and press right hand 4. Choose Internet protocol version 4 (TCP/IPv4) -> Press Properties. 5. Choose Obtain an IP address automatically. 6. In properties of Internet Protocol (TCP/IP), press OK. 7. Press OK in Network settings. 8. Make sure that, no Proxy settings is enabled in Internet Explorer settings 9. Now your workstation is ready for Internet Mac OS 1. Open AppleTalk -controller, choose Ethernet connection 2. Open TCP/IP -controller and modify these settings: Connection = Ethernet Definition = DHCP-server 3. Save settings. Now your workstation is ready for Internet Linux RedHat Open Start Here from desktop, go to System Settings and Network. 2. In Devices, double click mouse s left hand button on top of your Network adapter and modify these settings: Choose Automatically obtain IP address settings with: DHCP Choose Automatically obtain DNS information from provider 3. Press Ok. Now your workstation is ready for Internet Copyright 2007 A-Link Europe Ltd All rights reserved 7f28T RR24APi+ Recovery
How to upgrade the firmware
How to upgrade the firmware This document will detail how to update the firmware on DAP-1150. Ensuring the firmware remains up to date can assist with functionality / improved performances as well as adding
More informationLab - Connect to a Router for the First Time
Introduction In this lab, you will configure basic settings on a wireless router. Recommended Equipment A computer with Windows installed An Ethernet NIC installed Wireless router Ethernet patch cable
More informationNetwork Camera Firmware Upgrade Quick Guide
Network Camera Firmware Upgrade Quick Guide 09-2018 / v1.0 1 CONTENTS I Introduction... 3 II How to Upgrade Firmware for Network Camera... 4 III Download App... 11 2 I Introduction To strengthen the security
More informationNF3ADV VoIP Setup Guide (for Dodo)
NF3ADV VoIP Setup Guide (for Dodo) Configuring your NF3ADV for Dodo VoIP The following steps will take you through the process of setting up your VoIP connection. This guide assumes that the NF3ADV already
More information3G Router 431R/421R/321R/311R/221R/211R. Quick Start Guide
3G Router 431R/421R/321R/311R/221R/211R ---------------------------------------------------------- Version: 2.0----------------------------------------------------------- Check Package Contents: 3G Router
More informationNB16WV-02 VOIP Setup Guide (for Generic)
NB16WV-02 VOIP Setup Guide (for Generic) Configuring your NB16WV-02 for VOIP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer
More information1. Language setting. Frequently Ask Questions.
Frequently Ask Questions. 1. Language setting Step 1: Power on NB and you would see the following screen. Please click the language and select one you need as primary language. Step 2: Key in root user
More informationWNAP 3G MOBILE ROUTER. Quick Installation Guide
WNAP 3G MOBILE ROUTER Quick Installation Guide To avoid users without access right through your WNAP 3G Mobile Router, it is suggested to change WLAN SSID and password and admin password for web configuration
More informationTroubleshooting Can not access the router on
Troubleshooting Can not access the router on 192.168.0.1 Please note that when accessing the router s Web interface via http://192.168.0.1 you are not accessing some web site on the Internet. The router
More informationConfiguring the network clients
3 Configuring the network clients Accessing the wireless router Setting an IP address for wired or wireless clients To access the ASUS Wireless Router, you must have the correct TCP/IP settings on your
More informationConceptronic C54BRS4A Firmware Recovery Instructions
Conceptronic C54BRS4A Firmware Recovery Instructions When you have a Conceptronic C54BRS4A router and the firmware upgrade has gone wrong or you cannot access the router anymore, even after resetting it,
More informationInstallation Procedure Red Hat 7 with Netscape 6
Installation Procedure Red Hat 7 with Netscape 6 Pre-installation Requirements Before proceeding with the installation of a WatchGuard SOHO unit, you must have the following: A computer with a 10BaseT
More informationTROUBLESHOOTING : 1. Set up your wireless router via wired connection. 2. Please make sure your adapter is set to obtain IP automatically
1. Set up your wireless router via wired connection 2. Please make sure your adapter is set to obtain IP automatically 3. Please confirm web browser did not set up Proxy 3-1. In Internet Explorer, on the
More informationNB16WV VOIP Setup Guide (for GoTalk)
NB16WV VOIP Setup Guide (for GoTalk) Configuring you r NB16WV for VO IP Service The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network
More informationBefore installing this product, ensure that the following prerequisites are completed.
2 Preparation 2.1 Items to Check...2-2 2.2 Connecting PC with display unit...2-5 2.3 Setting PC Network...2-6 2.4 Set the network of display unit...2-19 2-1 Items to Check 2.1 Items to Check Before installing
More informationModel:BL-WR Mbps Wireless N Router
Quick Installation Guide Model:BL-WR3000 300Mbps Wireless N Router 1.Connecting the device Note: Please use wired network connections only to configure the Router. 1 Connect the WAN port on your Router
More informationFiery Installation Instructions for the WorkCentre 7300 Series
Fiery Installation Instructions for the WorkCentre 7300 Series This document describes how to install and set up the Fiery Network Controller for WorkCentre 7300 Series. IMPORTANT: The complete installation
More informationSNMP Manager User s Manual
SNMP Manager User s Manual Table of Contents 1. Introduction...1 2. SNMP Manager Install, Quick Start and Uninstall...2 2.1. Software Installation...2 2.2. Software Quick Start...2 2.3. Software Uninstall...3
More informationAPPLICATION NOTE AN0004 CHANGING THE IP ADDRESS ON AN EWSi PORTAL PLUS CONTROLLER WITH WINDOWS 7
INTRODUCTION Before installing an EWSi Portal Plus Controller on a network it is necessary to change the default IP address of the unit to one supplied by the network administrator. The following screen
More informationOUTDOOR IR NETWORK CAMERA Series
OUTDOOR IR NETWORK CAMERA Series INSTALLATION GUIDE Please read instructions thoroughly before operation and retain it for future reference. 1. OVERVIEW 1.1 Package Content Network camera Installation
More informationClick on Close button to close Network Connection Details. You are back to the Local Area Connection Status window.
How to configure EW-7228APn/EW-7416APn as a Repeater to extend wireless range This article can apply on EW-7228APn and EW-7416APn. We used screen shots of EW-7416APn in this instruction. We recommend you
More informationBefore installing this product, ensure that the following prerequisites are completed.
2 Preparation 2.1 Items to Check...2-2 2.2 Connecting PC with display unit...2-6 2.3 Setting PC Network...2-7 2.4 Set the network of display unit...2-19 2-1 Items to Check 2.1 Items to Check Before installing
More informationHow to upgrade firmware in DSL-xxx series router
How to upgrade firmware in DSL-xxx series router WARNING: DO NOT upgrade the firmware through a wireless connection. You may damage the router. Note that you will have to reconfigure the router after upgrading.
More informationThe Administration Tab - Diagnostics
The Administration Tab - Diagnostics The diagnostic tests (Ping and Traceroute) allow you to check the connections of your network components. Ping Test. The Ping test will check the status of a connection.
More informationWindows 2000/XP Network
This section provides installation and troubleshooting steps for Windows 2000/XP: Preliminary steps see page 23. Quick CD-ROM install steps see page 23. Other methods of installation see page 24. Quick
More informationPlease use only wired network connections to configure the Router.
Note Please use only wired network connections to configure the Router. Power down all of your network devices, including your computer(s) and the Modem Router. If you currently use a modem, disconnect
More informationBridge Cable User s Guide
Bridge Cable User s Guide Table of Contents Overview -------------------------------------------------------------------- 2 Driver Installation --------------------------------------------------------
More informationThis guideline works with Microsoft Windows only!
This guideline works with Microsoft Windows only! Please be aware that these steps will recover your LS400, but we cannot guarantee the data will still be stored on the device after the recovery. If you
More informationPHONE. user guide Version 1.1 FPP
Version 1.1 FPP 011004 INDEX FLIP KIT FLIP PHONE SPECIFICATION SETTING UP THE TERMINAL TERMINAL FUNCTIONS ADDENDUM I ADDENDUM II ADDENDUM III 5 5 6 9 12 16 17 3 FLIP KIT FLIP Terminal AC/DC Power Supply
More informationHow to Set-up the Ethernet Adapter
How to Set-up the Ethernet Adapter How to setup the Ethernet Adapter Step 1 The computer's Ethernet port needs to be configured with a static IP address. Usually Ethernet ports are set up for DHCP, which
More informationLevelOne. User's Guide. Broadband Router FBR-1402TX FBR-1403TX
LevelOne Broadband Router FBR-1402TX FBR-1403TX User's Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 LevelOne Broadband Router Features... 1 Package Contents... 3 Physical Details...4 CHAPTER 2 INSTALLATION...
More informationThermal Printer Configuration (EPSON)
Thermal Printer Configuration (EPSON) STEP A : IDENTIFY THE THERMAL PRINTER MODEL Check for your EPSON printer model by finding the label on the printer. Figure 1.1 For the example above (Figure 1.1),
More information2 Preparation. 2.1 Items to Check Connecting PC with GP Setting PC Network Setting GP Network...
2 Preparation 2.1 Items to Check...2-2 2.2 Connecting PC with GP...2-6 2.3 Setting PC Network...2-9 2.4 Setting GP Network...2-27 2-1 Items to Check 2.1 Items to Check Before installing this product, ensure
More informationSL620/DS-Tmini Snaplab+ Internet Configuration Setting procedure
SL620/DS-Tmini Snaplab+ Internet Configuration Setting procedure DNP PIE Nov 2015 V1.1 CONTENTS Introduction... 3 Router Update and Settings for SL-620:... 3 What is new?... 3 1. Updating the existing
More informationChapter 1 Getting Started with Switch Management
Chapter 1 Getting Started with Switch Management This section provides an overview of switch management, including the methods you can choose to start managing your NETGEAR GS700TS Gigabit Stackable Smart
More informationTCP/IP CONFIGURATION 3-6
TCP/IP CONFIGURATION 3. Type IPCONFIG /RENEW and press the Enter key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These
More informationP964 APR 964 Cable Router with 11g AP Quick Installation Guide VER. 1.0
P964 APR 964 Cable Router with 11g AP Quick Installation Guide VER. 1.0 CABLE POWER PORT LAN1~LAN4 Rear Panel Connections CONNECTION Connect the F-type connector to the CATV outlet using a coaxial cable.
More informationSMC Barricade Routers
SMC Barricade Routers User Guide SMC7004BR V1.0 Congratulations on your purchase of the SMC Barricade. The SMC Barricade is a Broadband Router designed to share Internet Access, provide security, and to
More informationLevelOne Broadband Routers
LevelOne Broadband Routers FBR-1100TX FBR-1400TX FBR-1401TX FBR-1700TX User's Guide TABLE OF CONTENTS CHAPTER 1 INTRODUCTION... 1 Features of your LevelOne Broadband Router... 1 Package Contents... 4
More informationLab - Configure a NIC to Use DHCP in Windows
Introduction In this lab, you will configure an Ethernet NIC to use DHCP to obtain an IP address and test connectivity between two computers. Recommended Equipment Wireless router Two computers running
More informationDominion KX II-101. Quick Setup Guide. Step 1: Configure the Target Server
Dominion KX II-101 Quick Setup Guide Thank you for your purchase of the KX II-101, the industry's most full-featured, enterprise-class, secure, digital KVM (Keyboard, Video, Mouse) switch. This Quick Setup
More informationPlease note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system.
Please note, instructions in this guide are based on a PC running Windows 7. Please adapt the actions to suit your operating system. Please follow these steps to ensure that any changes made by your previous
More informationQuick Installation Guide DSL-2650U. 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch
DSL-2650U 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2650U Power adapter DC 12V/1A RJ-11 telephone cable Ethernet cable (CAT 5E) Splitter (brochure).
More informationBroadband Router DC-202. User's Guide
Broadband Router DC-202 User's Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 Broadband Router Features... 1 Package Contents... 3 Physical Details...3 CHAPTER 2 INSTALLATION... 5 Requirements...
More informationF.A.Q for TW100-S4W1CA
F.A.Q for TW100-S4W1CA Q: How do I configure the TW100-S4W1CA for a DSL, PPPoE connection? A: Step 1 Open your web browser and type the IP address of the TW100-S4W1CA in the address bar. The default IP
More informationCorinex Communications Corp. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.
Copyright This Quick Start Guide, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of the license. The content of this manual
More informationDownloaded from manuals search engine
Table of Contents CHAPTER 1 INTRODUCTION... 1 Broadband Router Features... 1 Package Contents... 3 Physical Details... 4 CHAPTER 2 INSTALLATION... 6 Requirements... 6 Procedure... 6 CHAPTER 3 SETUP...
More informationHow to Restore a Windows System to Bare Metal
This article refers to the Barracuda Backup Legacy Release firmware or newer, except where noted. Bare metal recovery allows you to restore a complete Microsoft Windows system, including data, settings,
More informationQuick Installation Guide DSL-2540U. ADSL Annex B/Ethernet Router with Built-in Switch
ADSL Annex B/Ethernet Router with Built-in Switch BEFORE YOU BEGIN Delivery Package Router Power adapter DC 12V/0.5A RJ-11 telephone cable Ethernet cable (CAT 5E) Splitter CD-ROM with User Manual and (brochure).
More informationPHONE. user guide. Version 1.0 FPP
Version 1.0 FPP 010004 index KIT FLIP FLIP PHONE SPECIFICATION SETTING UP THE TERMINAL TERMINAL FUNCTIONS ADDENDUM I ADDENDUM II ADDENDUM III 5 5 6 9 12 16 17 KIT FLIP FLIP Terminal AC/DC Power Supply
More information28-Port 10/100/1000Mbps with. 4 Shared SFP Managed Gigabit Switch WGSW / WGSW-28040P. Quick Installation Guide
28-Port 10/100/1000Mbps with 4 Shared SFP Managed Gigabit Switch WGSW-28040 / WGSW-28040P Quick Installation Guide Table of Contents 1. Package Content... 3 2. Requirements... 4 3. Terminal Setup... 5
More informationInstallation Procedure Windows 2000 with Internet Explorer 5.x & 6.0
Installation Procedure Windows 2000 with Internet Explorer 5.x & 6.0 Printer Friendly Version [ PDF 266K ] Before You Begin Before proceeding with the installation of a SOHO 6 appliance, you must have
More informationWindows 95/98 Infoway Connection Instructions 1/4/2002; rev. 1/9/2002
Windows 95/98 Infoway Connection Instructions 1/4/2002; rev. 1/9/2002 The following are the basic steps for setting up your computer for a PPP connection to the library s Infoway Internet service. A PPP
More informationHow to manually set up EW-7228APn to extender wireless range
How to manually set up EW-7228APn to extender wireless range 1. Find out the IP address of your computer. Have your computer get on Internet as normally, without EW-7228APn turning on. If you use a Windows
More informationNCOM SERIAL DEVICE SERVER 1XX SERIES USER S MANUAL
NCOM SERIAL DEVICE SERVER 1XX SERIES USER S MANUAL 2017-07-07 Edition Titan Electronics Inc. Web: www.titan.tw Contents 1. INTRODUCTION... 4 1.1 Key Features... 5 1.2 Specifications... 6 2. PANEL LAYOUT
More informationSoHo 401 VPN. Shared Broadband Internet Access VPN Gateway 3-Port Switching Hub, DMZ Port. Quick Install Guide
SoHo 401 VPN Shared Broadband Internet Access VPN Gateway 3-Port Switching Hub, DMZ Port Quick Install Guide i This guide covers only the most common situations. Please refer to the full User Manual on
More informationDeploymentManager Ver6.6
DeploymentManager Ver6.6 Operation Guide -First Edition- Rev.001 Contents Introduction... 4 Target Audience and Purpose... 4 Document Structure... 4 Documentation Guidelines for DeploymentManager Manuals...
More informationwificam User's Guide Report Version: Date: November
User's Guide Report Version: 2.0.3 Date: November 9 2004 3JTech Co., Ltd. 342 Fu-Hsing N. Rd., 2F Taipei, Taiwan Tel: +886-2-2500 6919 e-mail: info@3jtech.com.tw 1 Revision History Version Date Changes
More informationDVG-2001S VoIP Terminal Adapter
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVG-2001S VoIP Terminal Adapter Before You Begin 1. If you purchased this VoIP Terminal
More informationWF-2402 Quick Installation Guide
WF-2402 Quick Installation Guide Netis 150Mbps Wireless-N Broadband Router 1. Check Your Package Contents The following items should be found in your package: 150Mbps Wireless-N Broadband Router Power
More informationBIPAC-6500 / 6500W (Wireless) Broadband VPN Firewall Router with 4-port 10/100M Switch Quick Start Guide
BIPAC-6500 / 6500W (Wireless) Broadband VPN Firewall Router with 4-port 10/100M Switch Quick Start Guide Billion BIPAC-6500 / 6500W (Wireless) Broadband VPN Firewall Router For more detailed instructions
More informationZyWALL 10W. Internet Security Gateway. Quick Start Guide Version 3.62 December 2003
Internet Security Gateway Quick Start Guide Version 3.62 December 2003 Introducing the ZyWALL The is the ideal secure gateway for all data passing between the Internet and the LAN. By integrating NAT,
More informationI-Storm USB ADSL modem A01-AU1
I-Storm USB ADSL modem A01-AU1 Manual for Linux and Mac OS 9/X A01-AU1_ME01 SOMMARIO Chapter 1...1 1.1 I-Storm USB ADSL Modem Features...1 1.2 Package Contents...1 1.3 The Front LEDs...2 1.4 Information
More informationApplication Notes for Ardence Desktop Edition with Avaya Interaction Center Issue 1.0
. Avaya Solution & Interoperability Test Lab Application Notes for Ardence Desktop Edition with Avaya Interaction Center Issue 1.0 Abstract These Application Notes describe the configuration steps required
More informationWindows 7. Connecting to the Wireless Network for Internet Access
Windows 7 Connecting to the Wireless Network for Internet Access Wireless Settings Network Name (SSID) CCCLIBRARY Wireless Mode (network type) Infrastructure IP settings Use DHCP WEP Disabled (DHCP must
More informationAT&T Digital Subscriber Line Service
AT&T Digital Subscriber Line Service Windows 2000 Professional PC Configuration Guide Overview Welcome to AT&T DSL Internet Service! This guide is designed to help you configure your PC to access the Internet
More informationMulti-Function Wireless A/P Router User s Guide
Multi-Function Wireless A/P Router User s Guide Model CNWR-811P Wireless Access Point Router W / Printer Sharing TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...1 CNWR-811P Features...1 Package Contents...3
More informationManagement Security Switch SGSD-1022 / SGSD-1022P SGSW-2840 / SGSW-2840P. Quick Installation Guide
Management Security Switch SGSD-1022 / SGSD-1022P SGSW-2840 / SGSW-2840P Quick Installation Guide Table of Contents 1. Package Content... 3 2. Requirements... 4 3. Terminal Setup... 5 4. Logon to the Console...
More informationStep 1: Checking Computer Network Settings:
Configuring your 3G18WV for VOIP The following steps will take you through the process of setting up your VOIP connection. Step 1: Checking Computer Network Settings: You will need to connect your computer
More information10/100Mbps 2Port USB2.0 MFP Server
10/100Mbps 2Port USB2.0 MFP Server Mini-MFP Quick Installation Guide English Ver.1.0 Quick Installation Guide CONTENTS STEP 1 / Mbps Port USB MFP Server Introduction Package Contents OS Requirements Physical
More informationRX3041. User's Manual
RX3041 User's Manual Table of Contents 1 Introduction... 2 1.1 Features and Benefits... 3 1.2 Package Contents... 3 1.3 Finding Your Way Around... 4 1.4 System Requirements... 6 1.5 Installation Instruction...
More informationHow to assign an IP address and access your device
User Manual Table of Contents Get started................................................ 3 Browser support................................................ 3 About default IP addresses........................................
More informationDecoder Firmware B1D-220-V AC User s Manual Decoder Firmware B1D-220-V AC User s Manual
Decoder Firmware B1D-220-V3.03.07-AC User s Manual i Table of Contents INTRODUCTION 1 1.1 Minimum system requirements 1 1.2 Preparation before setup 2 1.2.1 Setup your PC network 2 1.3 Configuring the
More informationMulti-Function Wireless Router. User's Guide. Wireless Access Point Broadband Internet Access. 4-Port Switching Hub
Multi-Function Wireless Router Wireless Access Point Broadband Internet Access 4-Port Switching Hub User's Guide Table of Contents CHAPTER 1 INTRODUCTION... 1 Wireless Router Features... 1 Package Contents...
More informationNCOM SERIAL DEVICE SERVER 4XX SERIES USER S MANUAL
NCOM SERIAL DEVICE SERVER 4XX SERIES USER S MANUAL 2017-07-07 Edition Titan Electronics Inc. Web: www.titan.tw Contents 1. INTRODUCTION... 4 1.1 Key Features... 5 1.2 Specifications... 6 2. PANEL LAYOUT
More information16/24/48-Port 10/100/1000T + 2/4-Port 100/1000X SFP Managed Switch GS T2S/GS T2S/GS T4S. Quick Installation Guide
16/24/48-Port 10/100/1000T + 2/4-Port 100/1000X SFP Managed Switch GS-4210-16T2S/GS-4210-24T2S/GS-4210-48T4S Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Requirements... 4 3.
More informationDSL-G624T. Wireless ADSL Router. If any of the above items is missing, please contact your reseller. This product can be set up using any
This product can be set up using any current web browser, i.e., Internet Explorer 6x or Netscape Navigator 7x. DSL-G624T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share your
More informationBEFCMU10 EtherFast Cable Modem with USB and Ethernet Connection. 12V-DC (0.6A min) power is connected. OFF
LED Table LED Color Mode Function Power Green ON 12V-DC (0.6A min) power is connected. OFF Power is not connected, power supply is incorrect or bad, or BEFCMU10 is bad. Activity Green ON Connection to
More informationMetasys System Direct Connection and Dial-Up Connection Application Note
Metasys System Direct Connection and Dial-Up Connection Application Note Code No. LIT-1201639 Software Release 5.1 Issued February 2016 Refer to the QuickLIT website for the most up-to-date version of
More informationNetwork I Lab 02. What are the major external components of the PC including the peripherals? / Characteristics
Part 01 : PC Hardware Network I Lab 02 Objective Become familiar with the basic peripheral components of a PC computer system. Identify PC connections including network attachment. Examine the internal
More information16/24-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Managed Switch GS P2S GS P2S. Quick Installation Guide
16/24-Port 10/100/1000T 802.3at PoE + 2-Port 100/1000X SFP Managed Switch GS-4210-16P2S GS-4210-24P2S Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Requirements... 4 3. Terminal
More informationQuick Installation Guide of Acer WLAN 11b Broadband Router
Preparation 1 At lease one PC with IEEE802.11b WLAN client installed. 2 One straight-through Category 5 Ethernet cable, used to link WAN interface to xdsl or CM for Internet connection. 3 Acer WLAN 11b
More informationUser Manual. Rev:
Default Login Details Login Address: www.mykasda.com Login Password: Set up by users Default Wi-Fi SSID: Kasda xxxx KW6516 (Printed on product label) Default Wi-Fi Password: 12345678 www.kasdanet.com Rev:
More informationProgramming through Web browser:
Connection Details Digital Inputs: There are 8 isolated digital inputs. Digital inputs will work from 5V to 24V DC. Every input has LED indications on top. LED will be ON when proper input is provided.
More informationX-Modem Ethernet ADSL Modem USER GUIDE
www.adslnation.com X-Modem Ethernet ADSL Modem USER GUIDE Technical Support TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN PROOF OF PURCHASE AND THE WARRANTY INFORMATION. To get product support or obtain product
More informationAirLive RS Security Bandwidth Management. Quick Setup Guide
AirLive RS-2000 Security Bandwidth Management Quick Setup Guide Important Information The AP mode s default IP address is The default Subnet Mask is The default login name is The default password is!!!!
More informationConnection to the OS32C
Connection to the This section describes how to connect a PC with the configuration software and the. The configuration software is connected to the via Ethernet. An Ethernet cable with an M12, 4-pin connector
More informationWireless a CPE User Manual
NOTICE Changes or modifications to the equipment, which are not approved by the party responsible for compliance, could affect the user's authority to operate the equipment. Company has an on-going policy
More informationUse this guide if you are no longer able to scan to Sharpdesk. Begin with section 1 (easiest) and complete all sections only if necessary.
Use this guide if you are no longer able to scan to Sharpdesk Instructions: Begin with section 1 (easiest) and complete all sections only if necessary. Section 1 Complete pages 3-5. Scan to the desired
More informationComputer/Laptop Registration
Computer/Laptop Registration Before you begin: You will need a valid KSU username and password. A computer or laptop with operating system of Windows (XP or higher) or Mac OSX. Confirm that your PC/laptop
More informationGV-I/O Box 4E. Contents
GV-I/O Box 4E Contents 1.1 Key Features... 2 1.2 System Requirements... 2 1.3 Packing List... 2 1.4 Overview... 3 1.5 Connecting to PC... 4 1.5.1 RS-485 Wiring... 4 1.6 Assigning Device ID to GV-I/O Box
More informationLevelOne FBR User s Manual. 1W, 4L 10/100 Mbps ADSL Router. Ver
LevelOne FBR-1416 1W, 4L 10/100 Mbps ADSL Router User s Manual Ver 1.00-0510 Table of Contents CHAPTER 1 INTRODUCTION... 1 FBR-1416 Features... 1 Package Contents... 3 Physical Details... 3 CHAPTER 2
More informationSonicWALL SSL VPN 2.5 Early Field Trial
Secure Remote Access Contents Platform Compatibility New Features Known Issues Resolved Issues Upgrading SonicWALL SSL VPN Software Procedures Related Technical Documentation Platform Compatibility The
More informationInstallation Procedure Red Hat 7 with Netscape 6
Installation Procedure Red Hat 7 with Netscape 6 Printer Friendly Version [ PDF 285K ] Before You Begin Before proceeding with the installation of a SOHO 6 appliance, you must have the following: A computer
More informationE7495A/B Remote Operation
E7495A/B Remote Operation E7495A/B Firmware Version: A.03.00 and later Java J2SE or VM Version: 1.4.2 NOTE: You must have J2SE 1.4.2 or later installed on your PC for the Remote GUI program to function
More informationSound Manager 2 User Guide
Sound Manager 2 User Guide Version 1.8.4 September 27 th, 2016 OVERVIEW 2 USER OPERATION 3-6 LOGIN SCREEN 7 OPTIONAL STEP 8-10 MAIN MENU 11 DEVICES TAB 11 ZONE TAB 12 EQ TAB 13 SOURCES TAB 14 SYSTEM TAB
More informationBEFORE INSTALLATION: INSTALLATION:
QUICK USER GUIDE INFORMATION TECHNOLOGY SERVICES SWINWIFI INSTALLATION GUIDE FOR WINDOWS XP BEFORE INSTALLATION: 1. Download Swinwifi installer to your desktop. You may download it from http://www.swinburne.edu.my/current_students.php.
More informationI m InTouch Installation Guide for the DSL/Cable environment with a Linksys router Models: BEFSRU31, BEFSR41 V.2, BEFSR11
I m InTouch router configuration p. 1 I m InTouch Installation Guide for the DSL/Cable environment with a Linksys router Models: BEFSRU31, BEFSR41 V.2, BEFSR11 Note: Different models may vary slightly
More information802.11g Super-G 108Mb Wireless Access Point Quick Installation Guide
802.11g Super-G 108Mb Wireless Access Point Quick Installation Guide The enclosed Hardware Installation Guide gives you a step-by-step explanation of how to install your 108Mb Super-G PCI Adapter. Further
More information24-Port 10/100/1000Mbps with. 4 Shared SFP Managed Gigabit Switch
24-Port 10/100/1000Mbps with 4 Shared SFP Managed Gigabit Switch WGSW-24040 / WGSW-24040R SGSW-24040 / SGSW-24040R SGSW-24040P / SGSW-24040P4 SGSW-24240 / SGSW-24240R SGSW-24040HP Quick Installation Guide
More information