The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter.

Size: px

Start display at page:

Download "The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter."

Blaze Shaw
5 years ago
Views:

The printer kit 556-00239 contains a TT230SM printer without cutter.

The cutter is required if printing and cutting HellermannTyton Solid Colored

2 The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter. The cutter is required if printing and cutting HellermannTyton Solid Colored Continuous Rolls. The printer with cutter should not be used for printing HellermannTyton ShrinkTrak or Foam Nameplate labels.

3 Each kit will contain a printer, hard shell case, TagPrint Pro 3.0 software and a ribbon. The kit will also contain a white ribbon.

Ensure that you have received all items associated with your order. This will include the following for both kits: TT230SM or TT230SMC thermal transfer printer.

4 Ensure that you have received all items associated with your order. This will include the following for both kits: TT230SM or TT230SMC thermal transfer printer. Caddy Cardboard ribbon core USB Stick USB cable Two pieces of Velcro Power supply Power cord Basic setup guide Tagprint Pro 3.0 label software A black ribbon **NOTE: The kit also contains a white ribbon.

The printer shown in this guide is the TT230SMC

5 The printer shown in this guide is the TT230SMC with cutter. Print Head After unpacking your printer, pull on the green release tabs on both sides of the printer lid. This will release the lid and allow it to open. Carefully remove the paper print head protector and discard. Do not touch the print head.

6 Pull open ribbon cover as shown in step 1. Insert the ribbon core by aligning the slot on the right side first and then pressing on the spring loaded spindle lock to engage the left side of the core as shown in these photos.

7 Do not touch Print head when loading ribbon. 4 5 Turn gear counter clockwise to tighten ribbon on core. Be sure to wind the ribbon until you only see BLACK and none of the blue leader.

8 1 Close ribbon cover. 2 Move guides apart. They are not needed. 3 Check that the sensor is centered in the printer. If not, move the sensor to the center.

9 Apply Velcro strips as shown

10 Once Velcro is applied to both the caddy and the printer bottom, attach the caddy to the printer by mating the Velcro strips as shown below.

11 Plug in the power supply and USB cable.

12 1 Insert caddy spindle through the core of the label roll. 2 3 Adjust the label guides using the small gear to the right side. The label stock should fit between the too guides, but not too tightly. Stock should move easily between the guides.

The label stock should fit between the too guides, but not too tightly.

13 Load the continuous roll of label stock as shown. Adjust the label guides using the small gear to the right side. The label stock should fit between the too guides, but not too tightly. Stock should move easily between the guides. Make sure to feed label through the printer opening

14 Press the green tab to release the cover so that it can be closed as shown below.

15 Turn on power to the printer. The light on the top of the printer, located by the Feed button should turn green.

16 Plug your USB stick into a separate port on your computer. This stick contains your printer driver. Plug your USB cable into a port on your computer.

17 SELECT OPEN FOLDER TO VIEW FILES

18 ACCESS THE FILES ON THE USB STICK DOUBLE CLICK ON HT719M3 TO OPEN THE DRIVER INSTALLER

19 CLICK ON NEXT

20 CLICK ON FINISH

21 Ensure that Install printer drivers is selected and click on NEXT.

22 Select the TT230SM driver (Select this even if you are installing a TT230SMC printer. Click on NEXT.

23 Select or highlight USB001 and click NEXT

24 The default printer name istt230sm. If you are installing a TT230SMC printer and wish to change this to TT230SMC, make the change and click NEXT.

25 Click FINISH and your printer driver should be ready to use.

26 Installing - System Requirements TagPrint Pro Standalone / TagPrint Pro Server TagPrint Pro Standalone Microsoft Windows XP SP3, Vista SP1 or later, Windows 7 and Windows 8 32 and 64 bit.net Framework MB RAM (XP SP3) 1.0 GB RAM (Vista/Windows 7) 500 MB available hard disk space TagPrint Pro Server PC running Microsoft Windows 7 or 8, Windows Server 2008.NET Framework 4 Microsoft SQL Server Express Edition GB RAM 500 MB available hard disk space NOTE: Microsoft Framework 4.0 is required before software installation. This is a free install from Microsoft, and is normally included on any Windows Updates. The user can run the Windows Updater, or visit Microsoft s Download Center to install this program.

27 Remove the TagPrintPro 3.0 installation disk from your package. Insert the CD into your CD ROM drive.

28 The following prompt will appear after the disk has been inserted into the CD ROM Drive. Click on Open Folder to View Files

29 A list of files will appear. Double click on the file named TagPrint.

30 TO INSTALL A SINGLE-USER VERSION, INSERT THE CDROM INTO THE COMPUTER. THE FIRST SCREEN THAT WILL APPEAR IS THE LICENSE AGREEMENT. CLICK ON THE CHECK BOX TO ACCEPT AND THEN CLICK ON INSTALL TO CONTINUE TO DEFAULT DIRECTORY AND SETTINGS. TO CHANGE THE INSTALL SETTINGS, CLICK ON ADVANCED.

31 THE FIRST SCREEN IN THE ADVANCED SECTION WILL ALLOW THE USER TO CUSTOMIZE THE INSTALL DIRECTORY. THE USER CAN CHOOSE TO INSTALL THE PROGRAM ANYWHERE ON THE COMPUTER CLICK NEXT.

32 THE NEXT STEP IS TO SELECT WHAT OPTIONS ARE TO BE INSTALLED. IF NO OPTIONS ARE INCLUDED, THE DEFAULT WILL BE A FULL INSTALL. CLICK ON INSTALL TO PROCEED.

33 A STATUS BAR WILL SHOW THAT THE SOFTWARE IS INSTALLING. THIS CAN TAKE A COUPLE OF MINUTES. CLICK NEXT.

34 THE SOFTWARE HAS BEEN INSTALLED. CLICK FINISH.

35 Launch the program via the Start menu and/ or the HellermannTyton folder TagPrint Pro 3.0 also can be launched from a Desktop icon or shortcut.

36 AT THE START OF THE PROGRAM, THE USER WILL SEE SOME INFORMATION ABOUT REGISTERING THE PROGRAM. THE SOFTWARE MUST BE REGISTERED TO QUALIFY FOR FREE TECHNICAL SUPPORT. IF THE SOFTWARE IS NOT REGISTERED, A MESSAGE WILL APPEAR ON THE MAIN SCREEN THAT STATES THAT THE PROGRAM WILL LOSE FUNCTIONALITY IF LEFT UNREGISTERED. ENTER

37 Note that your SERIAL key is located on the back of the CD ROM package. This will be needed after the software is installed.

38 ENTER THE SERIAL NUMBER, AND CLICK ON TEST.

39 CLICK TEST TO VERIFY THE SERIAL KEY. ONCE THE GREEN ARROW APPEARS, CLICK OK TO COMPLETE. TAGPRINTPRO 3.0 SOFTWARE IS READY TO USE

40 TAGPRINT3.0 Guide to printing continuous media THESE INSTRUCTIONS ARE FOR CREATING A STANDARD SIGN USING THE CONTINUOUS MEDIA.

41 OPEN TAGPRINT PRO 3.0 AND CLICK ON FILE.

42 CLICK ON NEW

43 CLICK ON CREATES A NEW FILE FOR EDITING A LABEL DESIGN IN THE APPLICATION

44 CLICK ON SELECT LABEL

45 UNDER FAMILY CLICK THE DOWN ARROW TO DISPLAY THE SUB MENU AND SELECT CONTINUOUS MATERIALS

46 NEAR THE BOTTOM OF THE LIST ARE LABELS IDENTIFIED AS CONTINUOUS VINYL. PICK THE WIDTH OF THE MARKER YOU WILL BE PRINTING IN YOUR TTM430 or TT230SM PRINTERS. IN THIS EXAMPLE, A 2 WIDTH IS SELECTED. NEXT CLICK ON EDIT

47 IF YOUR INTENT IS TO HAVE A 2 WIDE MARKER BY 2.5 LONG, THEN CHANGE THE HEIGHT FROM THE CURRENT 4.00 TO 2.50 IN THE LABEL MANAGER ABOVE.

48 IF YOUR INTENT IS TO HAVE A 2 WIDE MARKER BY 2.5 LONG, (AS EXAMPLE) THEN CHANGE THE HEIGHT FROM THE CURRENT 4.00 TO 2.50 IN THE LABEL MANAGER ABOVE. CLICK NEXT

49 YOU MUST ALSO CHANGE THE LENGTH TO 2.5 TO MATCH THE HEIGHT OF THE PREVIOUS SCREEN.

50 YOU MUST ALSO CHANGE THE LENGTH TO 2.5 TO MATCH THE HEIGHT OF THE PREVIOUS SCREEN. CLICK NEXT TO CONTINUE.

51 THERE IS NO NEED TO CHANGE ANYTHING ON THIS SCREEN. CLICK NEXT

52 THERE IS NOTHING TO CHANGE ON THIS SCREEN. CLICK FINISH

53 SELECT OK TO OVERWRITE THIS LABEL.

54 NOTE THAT THE LABEL DIMENSIONS IN THE MENU NOW SHOW THE WIDTH AS 2.0 AND HEIGHT AS 2.50 HIGHLIGHT THE LABEL BY CLICKING ON IT AND CLICK OK TO SELECT FOR EDITING.

55 ON THE LABEL DESIGN GUIDE, THE NEW SIZED LABEL NOW APPEARS. CLICK NEXT

56 IN THIS EXAMPE, TWO CONSTANT FIELDS WERE ADDED TO THE DESIGN. BASICALLY DESIGN YOUR LABEL AS NORMAL FROM THIS POINT FORWARD. ADD WHATEVER YOU DESIRE TO YOUR DESIGN. CLICK FINISH

57 DOUBLE CLICK ON THE CONSTANT FIELDS AND TYPE IN SOME TEXT FOR PRINTING. AGAIN, THE USER CAN DESIGN ANYTHING THEY DESIRE ON THIS TEMPLATE INCLUDING BARCODES, IMAGES, ETC.

58 WHEN THE LABEL DEIGN IS FINISHED, CLICK ON THE PRINT TAB AT THE TOP OF THE SCREEN.

59 SELECT YOUR PRINTER. IN THIS CASE, WE ARE ONLY WORKING WITH EITHER THE TT230SM or TTM430/TTM460 PRINTER MODELS.

60 CLICK ON PRINT SETUP

61 CLICK ON THE STOCK TAB. YOU WILL NEED TO CHANGE THE TYPE SETTINGS FROM LABELS WITH GAPS TO CONTINUOUS.

62 CLICK ON THE STOCK TAB. YOU WILL NEED TO CHANGE THE TYPE SETTINGS FROM LABELS WITH GAPS TO CONTINUOUS. IF YOUR PRINTER DOES NOT HAVE A CUTTER, THEN YOU ARE DONE AND CLICK OK. IF YOU DO HAVED A CUTTER, FOLLOW INSTRUCTIONS ON THE NEXT SLIDE.

63 IF YOU DO NOT HAVE A CUTTER ON YOUR PRINTER, THEN YOU ARE FINISHED. JUST CLICK OK. IF YOU HAVE A CUTTER ON YOUR PRINTER, CLICK ON POST-PRINT ACTION AND CHANGE TO CUT

64 WHEN FINISHED, CLICK OK YOU CAN NOW PRINT AS NORMAL. MAKE SURE YOUR PRINTER IS LOADED WITH THE 2 CONTINOUS MEDIA (IF THAT IS WHAT YOU USED) AND THAT THE PRINTER IS IN GREEN LIGHT MODE.

The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter.

The printer kit contains a TT230SM printer without cutter. The printer kit contains the TT230SMC printer with cutter. The printer kit 556-00239 contains a TT230SM printer without cutter. The printer kit 556-00256 contains the TT230SMC printer with cutter. The cutter is required if printing and cutting HellermannTyton