TOPEX VoiBridge. (VoIP-to-GSM Gateway) Basic Configuration

Transcription

1 TOPEX VoiBridge (VoIP-to-GSM Gateway) Basic Configuration 2009

2 CONTENT 1 VoiBridge configuration by means web interface Access the web interface Changing the IP Address Changing the default Password Configure the equipment 5 2 VoiBridge configuration with OAM application Configure the serial connection 7 3 O.A.M. Installation 11 4 Add your Voxiplus gateway system to the OAM configuration 13 5 Changing the IP address with the OAM application 16 6 Adding a card to the OAM configuration Adding a card Removing a card Port configuration 19

3 1 VoiBridge configuration by means web interface The VoiBridge configuration can be accomplished after all the connections were achieved and the power up was done. This operation can be performed using the web interface incorporated by TOPEX VoiBridge equipment. For basic configuration of the Topex gateway, perform the following steps: Access the web interface Change the default IP address Configure the equipment from the web interface 1.1 Access the web interface type: (the default IP address as the URL) After you access the web browser, the following window will appear and ask you about the user name and the password: type user name - admin the password - 99admin11 Press LogIn button

4 1.2 Changing the IP Address Initially the equipment is delivered with a default IP address This must be changed with an IP address from the IP address range in your LAN network. Access the System menu Access the Network option from System menu Insert your network parameters: IP Address, Netmask, Gateway Press Save button in order to activated the new parameters: IP Address, Netmask, Gateway and then Commit The equipment will reboot and you will be able to login with http on the address given in the LAN Network Settings menu.

5 1.3 Changing the default Password Initially the equipment is delivered with a default username: admin and password: 99admin11. For security reasons we advise you to change the password used for accessing the web interface. Access the System menu Access the Password option from System menu Insert the new password Press Save button in order to activated the new password and then Commit Use the commit button to make your changes permanent. By using only the Save button; changes will be available until first reboot. 1.4 Configure the equipment The VoiBridge configuration is available by using the web interface, the operation instructions are described in Web Interface Manual which founds out on the TOPEX CD.

6 2 VoiBridge configuration with OAM application The VoiBridge configuration can be accomplished after all the connections were achieved and the power up was done. Also, there are two methods to achieve the VoiBridge configuration: By means OAM application By means Web interface These operations can be performed either using the serial or the Ethernet connection, for these connections the default parameters must be known. The VoiBridge equipment default parameters are: a. For serial connection: Bits per second ; Data bits 8; Parity None; Stop bits - 1; Flow Control None. IP address on the LAN side, must be changed with a private IP address or a public IP address Permissions for ordinary user: user name - gsmgw password: 5tgb4rf or user name - tpxadm password: u53rp455 Permissions for advanced user: user name - root password: 91qwerty19 b. For Ethernet connection: IP address on the LAN side, must be changed with a private IP address or a public IP address SSH port Permissions for ordinary user: user name - gsmgw password: 5tgb4rf or user name - tpxadm password: u53rp455 Permissions for advanced user: user name - root password: 91qwerty19 To configure the Topex gateway, perform the following steps: Achieve a direct connection (by OAM or web) to the VoiBridge equipment Change the default IP address Set up the local time of the equipment Install the OAM application Configure the equipment from the OAM application When you move the gateway to another location or office, or if you send it back to Topex for upgrade or repairs, you should remember to restore the default IP address!

7 2.1 Configure the serial connection In order to change the IP address you must connect to the Topex gateway from a desktop or notebook computer using the serial (RS-232) connection. Verify that the special serial cable is properly connected Set the serial port (COM) properties of your computer to match the parameters of the VoiBridge serial connection (Bits per second ; Data bits 8; Parity None; Stop bits - 1; Flow Control None). See below an example for the Windows XP operating system: Set the serial port properties: Select Start>Control Panel> System From System select Properties>Hardware> Device Manager :

8 From Device Manager select Ports> COMx, where x is the first available serial port of your computer; in this example, COM1 was used: Configure the Properties for respective COM port as shown:

9 Create a new serial connection for VoiBridge equipment You must use a serial communication program (terminal emulator) to connect to the Linux console of the VoiBridge equipment. The programs may be HyperTerminal" under Microsoft Windows, TELIX for DOS/Windows, Minicom from Linux, TERM95 under MS-DOS etc Launch the program: Start>Accessories>Communications>HyperTerminal:

10 Create a new Connect to entry and name it, for instance TopexVoIPGateway. select the COM port where you have connected the serial cable, like COM1 in the example shown here Set the initial communication parameters for the serial link. Bits per second: bps or leave the default rate Data bits: 8 Parity: none Stop bits: 1 Flow control: none

11 3 O.A.M. Installation Now that the Topex gateway is configured, you can start using the OAM program to configure the parameters of the equipment and monitor its operation. Install the OAM (Operation, Administration and Maintenance) application on a PC or notebook. The OAM software is delivered on a CD included in the TOPEX package. The PC where you install the OAM application must fulfill these minimum requirements: Processor with 1 GHz frequency; 128 MB RAM memory; 20 GB hard disk capacity; Ethernet connector; CD-ROM; Windows XP or Windows Vista. Install the OAM application from the CD included on the package of the TOPEX VoiBridge equipment or download the updated installation kit from the TOPEX web site. For detailed information about the OAM installation procedures see the USER_Manual comprises on the CD delivered by TOPEX.

12 Insert the Topex CD-ROM into the drive. If the Autorun feature for the `CD-ROM enabled on your PC, the installation of OAM should begin by itself, since the program features auto-run: The first installation screen shows: the Topex logo, the name of the program being installed and the equipment range for which the program is intended:! If the displayed equipment range is different means that the OAM CD is wrong and must ask TOPEX about proper OAM CD. Then a Preparing Setup screen is displayed, mentioning the name of the OAM program to be installed, such as Topex VOXI OAM and showing a progress indicator for the Setup program. If you notice it is the wrong type of program, you can click the Cancel button at the bottom right corner to abort the installation.

13 4 Add your gateway system to the OAM configuration After the successful installing the OAM application you must add the The RGW equipments into the configuration, for this follow the next instructions. select "Actions" and the following window will appear, asking you to add another TOPEX system to the configuration.

14 select "Actions > Add System" and the following window will appear, asking you to add another TOPEX system to the configuration. Here you must set the parameters assigned to your gateway. Assign a Directory name for your VoxiPlus Gateway System into the field Directory The name types in Directory field means the folder in where the files downloaded from the TOPEX system will be stored. On HDD it will be made a directory in the following shape "cfg_xxxxxxx" where directory is the name typed in the "Directory" field. The folder will be created on HDD in the directory where the executable 'gwconfig.exe' is located. Assign the Name for the connection to your System into the field Name This names is concatenated at "cfg_" and this it will be the text used in tree structure (OAM configuration) for identifying the system. Specify the type of communication IP or serial You must check IP communication or serial communication option it is specified link type between OAM computer and radio equipment. These are the two exclusive options for the communication with a TOPEX gateway equipment.

15 For IP communication option: Define the IP parameters IP address - enter the IP address of the system enter the default IP address Note: In the previous window - you can notice one IP address, one port number and one serial port number for each processor card. IP Port num - enter the number of the port through which the communication with the system is achieved. The default value is This value is established also into the gateway system and should not be modified. For serial communication option: Define the serial parameters Serial Port num - enter the serial port used in case of serial communication with the gateway. The default value is COM1. This value must be in range COM1-COM12. Save the configuration for new added system Press the Save button (for the window shows in figure 1) to complete the adding of a new system via OAM application.

16 5 Changing the IP address with the OAM application In order to change the default IP address with an IP address belongs to your LAN, perform the steps described below: Select the Parameters option from the configuration structure In the Modifying system parameters on position X window enter the new IP address into IP address field Press Save button

17 6 Adding a card to the OAM configuration 6.1 Adding a card Click on the position where you want to add the card > the message Add card no X will be displayed > press OK > enter the password topex then OK.

18 Detailing of operations to add a new card to the configuration: Click on an uninstalled card position (an empty rectangle) an option for adding a card will appear Enter the password default is topex This is password protection for adding a card. Press OK to confirm for adding a card Select the type of card which you want to add. The available types of cards for VoiBridge are: GSM, VoIPI

19 6.2 Removing a card To remove (delete) a board from the system you must left click with the mouse on a position with installed board and then confirm the action of eliminating that board from the system. Note: In order to maintain coherency a change in the configuration of the boards must be accompanied by the updating of the configuration of the ports. This is achieved by pressing the button Apply from the window with the changes for the ports (the records for ports from the ports file - for that board will be deleted). 6.3 Port configuration The second configuration window refers to the configuration of the ports: Port Configuration. In this window will be displayed the same information as for the option Status information minus the zone Card status. To change categories and fields you left click with the mouse button on a position then operate in the setting window that shows up. For instance, in the subscriber port case, on the screen will appear the Changing Setting window which contains the parameters: