TouchKit TouchScreen Controller User Guide for Windows NT4 Version: 3.2.1

Size: px

Start display at page:

Download "TouchKit TouchScreen Controller User Guide for Windows NT4 Version: 3.2.1"

Nora Caldwell
6 years ago
Views:

1 TouchKit TouchScreen Controller User Guide for Windows NT4 Version: TouchKit Guide for WinNT4 v

2 CONTENT CHAPTER 1. TOUCH PANEL CONTROLLER CONTROLLER SPECIFICATIONS AND FEATURES... 3 CHAPTER 2. INSTALLING AND USING TOUCHKIT... 5 CHAPTER 3. CONFIGURATION UTILITY AND RIGHT BUTTON EMULATOR... 8 CHAPTER 4. UNINSTALLING TOUCHKIT TouchKit Guide for WinNT4 v

3 Chapter 1. Touch Panel Controller This touch panel controller provides the optimistic performance of analog resistive touch panels for 4 wire, 5 wire and 8 wire models. It communicates with PC system directly through RS232, PS/2 or USB connector. Users can see how superior the design is in sensitivity, accuracy and friendly operation. The touch panel driver emulates mouse left and right button function and supports operation systems including Microsoft Windows 95/98/ME/NT4/2000/XP/XP Tablet PC Edition, Windows CE 2.12/3.0/.NET, Linux, imac and DOS. 1.1 Controller Interface RS232 USB PS/2 4-wire Ready Ready Ready 5-wire Ready Ready Ready 8-wire Ready Ready Ready Capacitive Ready Ready X TouchKit Guide for WinNT4 v

4 1.2 Specifications and Features Specifications for Touchkit controller. Specifications Power requirements Operating temperature 0 to 50 Storage Temperature -40 to 80 +5VDC ( Maximum 100mA, typical 70mA, 50mV peak to peak maximum ripple ) Relative Humidity 95% at 60 Protocol RS232 Model: 9600 bauds, None parity, 8 data bits and 1 stop bit USB Model: USB 1.1 Low speed PS/2 Model: PS/2 mouse Resolution 2048 X 2048 Report rate RS232 Model: Max. 160 points/sec USB Model: Max. 160 points/sec Response time PS/2 Model: Max. 140 points/sec Resistive: Max. 35 ms Capacitive: Max. 20 ms Pin out definition 4 wire model: X+, Y+, X-, Y- 5 wire model: UL, UR, COM, LR, LL 8 wire model: X+, X+ref, Y+, Y+ref, X-, X-ref, Y-, Y-ref Panel resistance Regulatory Approvals 4, 8 wire resistive model: 200 ~ 900 ohm ( pin to pin on the same layer ) 5 wire resistive model: 50 ~ 200 ohm ( pin to pin on drive layer ) FCC-B, CE TouchKit Guide for WinNT4 v

5 Features for Touchkit software Features Calibration Fast full oriental 4 points position Compensation Accuracy 25 points linearity compensation. Draw Test Position and linearity verification Extend Features 1. Support monitor / display rotation 2. Support multiple monitor / display 3. Support QVGA and Half-VGA function 4. Support edge compensation Controller Setting 1. Support multiple controllers 2. Dynamical add / remove controllers 3. Change Controller interface without reboot. Language Support 10 languages for Windows Mouse Emulator 1. Right / Left button emulation 2. Normal / Click on touch / Click on release mode 3. Auto right button Sound Notification 1. Sound option ( No Sound / Touch Down / Lift Up ) 2. Frequency adjustment Double Click 3. Duration adjustment 1. Configurable double click speed 2. Configurable double click area OS support 1. Windows 95 / 98 / ME / NT4 / 2000 / XP / Windows XP Tablet PC Edition 2. Windows CE 2.12, 3.0,.NET 3. Linux ( X Window Version: 3, 4 Red Hat 6.0 ~ 9.0 Mandrake 5.0 ~ 9.1 ) 4. imac. OSX 5. MS-DOS: Support display resolution: 320x200, 640x200, 640x350, 640x480, 800x600, 1024x768 and 1280x1024 COM port support 1. Support COM 1 ~ COM 256 for Windows and Linux 2. Support COM 1 ~ COM 8 for DOS TouchKit Guide for WinNT4 v

6 Chapter 2. Installing and using TouchKit TouchKit is software, which contains drivers of the touch panel controllers for the specified communication connectors, RS232, PS/2 and USB, and the other two utilities: Touch Tray support This is utility for emulating the right and left button of mouse through controlling touch panel. Users can toggle between right or left mouse buttons by this utility. Configuration support The calibration and draw test of touch panel are done by this utility. Besides, users can add or remove for new RS-232, PS/2 or USB touch panel devices. Follow these steps to install TouchKit. 1. Put the TouchKit CD to CD-ROM. 2. Change directory to WinNT4 3. Double click the Setup.exe, then windows starts to run the installation program. 4. Just click [Next >] button to continue installation. TouchKit Guide for WinNT4 v

5. Then check the check box if PS/2 touch controller is to

7 5. Then check the check box if PS/2 touch controller is to be installed. The default is unchecked. Then Press [Next >] to continue installation. System will give you a warning, if users check the PS2AUX check box, 6. Select the appropriate folder where set-up files will be installed. Then Press [Next >] to continue installation. TouchKit Guide for WinNT4 v

Once the controller was scanned, the setup program will display a dialog as Click Yes to add the controller on the specified COM port automatically. 8.

8 7. Then type in the name of program folder for TouchKit or press [Next >] to continue. There will be a default name for it. During driver installation, the setup program will scan COM port for RS232 Touchkit controller. Once the controller was scanned, the setup program will display a dialog as Click Yes to add the controller on the specified COM port automatically. 8. Windows is copying files to disk and the setup is complete. It will request re-boot computer. Press [Yes >] to re-boot immediately or [No >] to re-boot later. The installation will not be finished until system re-boot. TouchKit Guide for WinNT4 v

9 Chapter 3. Configuration Utility and Right Button Emulator There are five property pages in TouchKit utility, and they are General, Setting, Edge coefficient, Monitors and About. Each property page contains different functions for users to do the adjustments. Therefore, users can easily manage all the TouchKit controllers through TouchKit Utility. Functional Group Tab General General property page contains the functions of language selection, devices add/ remove, 4 points calibration, Draw test and advanced. General Function TouchKit Guide for WinNT4 v

10 <Language> TouchKit supports multi-language user interface. Users could select native language that is compatible to operation system support. For example, if the operation system is a traditional Chinese version, users could see the normal display words under the traditional Chinese and English mode. There are ten different languages, English, Traditional Chinese, Simplified Chinese, French, Spanish, German, Japanese, Italian, Korean amd Dutch supported in this feature of TouchKit. Note to select the compatible language first. Select the compatible language first or users may not see the normal display of each button. <Add> / <Remove> Please check the touch panel devices (including its controller) are equipped well, then click [Add] button to add all of those RS-232 and PS/2 devices to the Panel List dialogue box. There is one devices found. Press [Yes] to continue. TouchKit Guide for WinNT4 v

Device is found in COM1 The controller is displayed on the Panel List box. Users can get the information of interface, type, firmware version and baud rate for each controller.

11 Device is found in COM1 The controller is displayed on the Panel List box. Users can get the information of interface, type, firmware version and baud rate for each controller. Select one device after added more than one device at the panel list window. The one selected will activate the panel, and remember to do the calibration before starting to use touch panel. TouchKit Guide for WinNT4 v

There are three buttons, [4pts Cal] [Draw Test] [Advanced], at the lower section of the General property page. <4pts Cal> Correct 4 point locations on screen with the panel.

12 There are three buttons, [4pts Cal] [Draw Test] [Advanced], at the lower section of the General property page. <4pts Cal> Correct 4 point locations on screen with the panel. Press [4 pts Cal], screen displays as follows. Touch the blinking symbol on panel until beep or stop blinking. <Draw Test> Test the drawing position related to the display screen on panel. Click on the [Draw Test] button. There will be a squared blue display showing. In drawing test window, users can click [Clear] button to clear the window. Also, users can click [Quit] or press mouse right button to quit from the drawing test. In drawing test window, users can verify the panel linearity, calibration capability, and drawing line quality. TouchKit Guide for WinNT4 v

If the capacitive controller is selected, a capacitive setting property page appears on the advanced sheet.

13 <Advanced> Touchkit provide more accuracy 25 points calibration for touch sensor. In addition, Touchkit provide controller setting for capacitive touch sensor. If the capacitive controller is selected, a capacitive setting property page appears on the advanced sheet. In general case, it does not need to do 25 points calibration other then bad linearity sensor. Press [Clear] to clear the previous calibration records. Press [Yes] to clear previous records.the record will become default record. Press [25ptCal] to do 25 points calibration. Correct 25 point locations on screen with the panel. TouchKit Guide for WinNT4 v

property size of capacitive screen first, and press [Restart] The capacitive controller will restart, and do not touch the screen

14 Touch the blinking symbol on panel until beep or stop blinking. After the calibration, the new record will overwrite the old one. If the selected controller is capacitive type, an extra property page for capacitive setting adjustment shown as below: Please select property size of capacitive screen first, and press [Restart] The capacitive controller will restart, and do not touch the screen before the warning message disappears Warming: Do not adjust the sensitive and sampling time without RD help TouchKit Guide for WinNT4 v

15 Setting There are three functional groups in Setting property page, and at the upper section of the property page is sound option; at the middle section is Mouse Mode; and at the lower section is Double Click Adjustment. The Sound options provide users the click feedback while touching the panel. Select preferred option first. Sound options <No Sound> Users could choose to make no sound while using the touch panel. <Touch Down> The system will make a sound while touching the panel. <Lift Up> The system will not make any sound until finger leaves the touch panel. <Frequency> Sound frequency, drag the cursor from left to right is low to high. <Duration> Sound duration, drag the cursor from left to right is short to long. TouchKit Guide for WinNT4 v

The Mouse Mode provides users different operating options. They are as follows: Mouse Mode <Mouse Button> Click it to show / hide Touch Tray on the right bottom corner of the desktop.

16 The Mouse Mode provides users different operating options. They are as follows: Mouse Mode <Mouse Button> Click it to show / hide Touch Tray on the right bottom corner of the desktop. The touch panel system starts with the computer booting, and a mouse icon shows in the taskbar. Users can choose show or hide Touch Tray from the mouse icon in the taskbar. Just click the mouse icon to choose show or hide. Touch Tray Change right / left button by clicking the upper small rectangular box of Touch Tray. Blue area expresses what button has been selected. TouchKit Guide for WinNT4 v

<Mouse Mode> There are three kinds of mouse mode users could choose, [Normal Mode] It provides all the mouse functions, including the dragging function.

17 <Mouse Mode> There are three kinds of mouse mode users could choose, [Normal Mode] It provides all the mouse functions, including the dragging function. [Click on Touch] Click action is executed as soon as users touch the panel. [Click on Release] Click action will not be executed until finger leaves the panel. <Option> Touchkit provides an option for advanced Mouse Emulation setting. When the Option button is pressed, a setting property sheet will be popped up. Support Constant Touch and Support Auto Right Button check boxes are shown in the property sheet to enable / disable Constant touch and Auto right button support. [Constant Touch] Enable Constant Touch to force driver to stop reporting touch point when the movement is small. Therefore, the user can see a stabilized cursor instead of a chattering cursor when users touch the same point with unwanted noise. [Auto Right Button] Enable Auto Right Button to force driver to report a right click mouse event to OS when users lift up from a constant touch. It no longer needs to touch the right button in the touchtray to activate a right click. This feature makes users to do right click more easily with touchscreen. TouchKit Guide for WinNT4 v

<Cursor Visibility> Cursor visibility function provides users to hide the cursor in the display. Please go to Start / Control Panel / Mouse / Pointers / Scheme, and choose TouchKit Hide Cursor.

18 <Cursor Visibility> Cursor visibility function provides users to hide the cursor in the display. Please go to Start / Control Panel / Mouse / Pointers / Scheme, and choose TouchKit Hide Cursor. Press [Apply] to make setting change, and press [OK] to escape the property page. If users want to cancel the function of TouchKit Hide Cursor, do the steps again and choose the other scheme. TouchKit Guide for WinNT4 v

19 The Double Click adjustment provides users to set up the tolerance while double clicking. They are as follows: Double Click Adjustment <Double Click Speed> Double Click Speed is the double click response time for Windows system. Users can adjust the proper double click for easy double click by touch panel. <Double Click Area> Each one touch has its own touch tolerance once someone may not fix in one point. So if users set the Double Click Area to <Smaller>, the panel will be very sensitive about micro-move while users want to fix on a point. If users set it to <Larger>, it tolerates the larger touch point movement while users want to point at a fixed position. TouchKit Guide for WinNT4 v

20 Edge Coefficient Edge Coefficient property page contains the functions of Edge Compensation for Top, Bottom, Left, Right, X Axis and Y Axis. In some case, if it is difficult to touch items at the edges of the touch panel, users can set adjustment to reach the edges of the screen image. <Top> If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position of the top edge. If users set the Edge to <Larger>, TouchKit will extend the horizontal position of the top edge. <Bottom> If users set the Edge to <Smaller>, TouchKit will reduce the horizontal position of the bottom edge. If users set the Edge to <Larger>, TouchKit will extend the horizontal position of the bottom edge. <Left> If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of the left edge. If users set the Edge to <Larger>, TouchKit will extend the vertical position of the left edge. <Right> If users set the Edge to <Smaller>, TouchKit will reduce the vertical position of the right edge. If users set the Edge to <Larger>, TouchKit will extend the vertical position of the right edge. TouchKit Guide for WinNT4 v

In some case, cursor will be behind the finger when users touch the panel. If users can not see the cursor when they touch down on the panel, users can set X Axis or Y Axis to move the cursor.

21 In some case, cursor will be behind the finger when users touch the panel. If users can not see the cursor when they touch down on the panel, users can set X Axis or Y Axis to move the cursor. <Offset X Axis> If users set the Offset X Axis to <Smaller>, cursor will be moved a pixel of X Axis to left. If users set the Offset X Axis to <Larger>, cursor will be moved a pixel of X Axis to right. <Offset Y Axis> If users set the Offset Y Axis to <Smaller>, cursor will be moved a pixel of Y Axis to top. If users set the Offset Y Axis to <Larger>, cursor will be moved a pixel of Y Axis to bottom. Edge Compensation Switch <Edge Compensation Switch> Users can choose Edge compensation Enable / Disable from left bottom corner of Touchkit Utility. Using +10% and -10% button to adjust the smaller or larger of edge. If users press +10% button, the top, bottom, left and right edges will extend 10% of orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to right and top. If users press -10% button, the top, bottom, left and right edges will contract 10% of orientation to touch screen, and cursor will be moved 10 pixel of X and Y Axis to left and bottom. If users want the value back to the default value, choose Default button. TouchKit Guide for WinNT4 v

<Split Monitors> To use the Split Monitor function, users need to select which controller you want to launch this function, then check the Multiple Monitors box and Split Monitor at the same time as

22 Monitors There are three functions in this property page, and they are Multiple Monitors, Split Monitor and One Point Calibration. Such a trendy and yet innovated design provides viewing pleasures, viewing flexibility and convenience to users. <Multiple Monitors> This function is not supported for WindowsNT4. <Split Monitors> To use the Split Monitor function, users need to select which controller you want to launch this function, then check the Multiple Monitors box and Split Monitor at the same time as showing as the follow picture. Press the [Split Setting] button to set up the activate area. It shows the current resolution of display and users can set up the activate area by inputting the value by yourself or use the default button [Upper Half], [Left Half] or [Quarter]. The default value of panel resolution should be full screen as Left: 0, Right: 0, Top: 0 and Bottom: 0. TouchKit Guide for WinNT4 v

<One Point Calibration> Touchkit utility provides a fast tool to identify the touchscreen orientation when the monitor display was rotated by 90 degrees.

23 <One Point Calibration> Touchkit utility provides a fast tool to identify the touchscreen orientation when the monitor display was rotated by 90 degrees. Enable this One Point Calibration feature, Touchtray will pops up this One Point Calibration tool for users to identify and correct the touchscreen / monitor orientation whenever the monitors was rotated by 90 degrees. Disable this feature, Touchtray does not pop up this One Point Calibration tool. Then, the user has to do four points calibration to correct the orientation whenever the monitor was rotated. About Information about TouchKit. TouchKit Guide for WinNT4 v

24 Chapter 4. Uninstalling TouchKit Follow these steps to uninstall TouchKit. 1. Go to Start / Programs / TouchKit / Uninstall, and execute it. 2. TouchKit setup dialog appears, and prepares to uninstall. 3. Confirm dialog, press [OK] to start un-installation; [Cancel] to cancel uninstallation. TouchKit Guide for WinNT4 v

25 4. Start to uninstall TouchKit. If users do not want to uninstall TouchKit at this moment, press [Cancel] to terminate the uninstall process. 5. TouchKit will not be removed until system re-boot. Press [Yes] to re-boot immediately or [No] to re-boot later. TouchKit Guide for WinNT4 v

TouchKit TouchScreen Controller User Manual for Windows NT4 Version: 3.4.0

TouchKit TouchScreen Controller User Manual for Windows NT4 Version: 3.4.0 1 CONTENT CHAPTER 1. TOUCH PANEL CONTROLLER 2 1.1 Controller 2 1.2 Specifications and Features 3 CHAPTER 2. INSTALLING TOUCHKIT