Setting up a RIS (Remote Installation Service) server (Windows Server 2003 SP 1) Updated February 13 th, 2008.

Transcription

1 Setting up a RIS (Remote Installation Service) server (Windows Server 2003 SP 1) Updated February 13 th, The most up to date version of this document can be found at the following link anyweb@linux-noob.com Step 1. (This will take some time so be patient ) Install The os by booting from the Windows Server 2003 CD, make sure to have one partition for the os (windows 2003 server) and one partition to be used purely as the RIS share Once the os is fully installed and relavant drivers installed, Click on 'Add or remove a role' in the Manage your server dialog box. click 'next' to continue, ignore any DHCP errors for your network controller as we will be making this a DHCP server shortly... Choose 'custom configuration' and scroll down to the 'Domain Controller (Active directory) option

2 You ll then see the following screen

3 You wil now see an Active Directory Installation Wizard pop up

4 Click next to continue click next again to continue and select the following configuration

5 Next we have to give it a DNS name

6 Then the Netbios name And then it ll prompt for the database and log folders, go with the defaults as below

7 If you get a DNS diagnostic Failed error simply choose to Install and configure the DNS (second option)

8 Note: The error you have experienced while using the Active Directory Installation Wizard does not prevent you from successfully promoting this server to a domain controller. You may continue to promote this server and then correct its DNS configuration following promotion.

9 Set your permissions as above Then enter a password for restore mode!

10 Review the actions performed Click next and it will configure your server You may be prompted to insert the Windows 2003 Server CD

11 If you have a network cards installed and setup to receive its IP from another DHCP server (a router for example) then you may get an error like this I chose Local area connection, then properties, then TCP/IP properties and manually added the following: Manually configure the network cards tcpip properties for

12 I then clicked on OK *(three times) If you get a message about it using the localhost ip for DNS then click OK. At this point the wizard may appear to be hanging, but it isn t, just be patient and wait until it completes (can take 15 minutes or so) When it s finished you ll see this

13 After clicking finish you ll be asked to restart.

14 reboot when prompted. After the reboot you should see this Click Finish and then click 'Add or remove a role' in the Manage your server dialog box. Click next and then continue (ignore this error if you get it)

15 scroll down to DHCP server and click next.

16 The wizard will probably copy some files from the Windows 2003 server CD

17 Next we need to configure our scope (New Scope Wizard)

18 Don t bother to add any exclusions (just click next)

19 Leave the lease duration as default, and next select No, I will configure these options later for the DHCP scope options

20 You should now see this

21 Click Finish. Now we need to activate the scope, click on Start/All Programs/Administrative tools/dhcp

22 right click on the highlighted scope and choose activate then right click on the DHCP server with the red mark above the scope, and choose Authorize

23 Once done you should now have the DHCP server scope activated and the DHCP server authorized in active directory. If the DHCP server doesn t appear green hit the Refresh button a few times.

24 Ok, that was Step 1, took a bit of time didn t it??

25 Step 2. Click on 'add or remove programs' in Control panel chose 'Add/remove Windows Components' Scroll down to 'Remote Installation Services', place a check mark in the empty box and click next to continue. (Windows will prompt for the Server CD so make sure it's in the drive).

26

27 Once done, click Finish and reboot the computer when prompted to do so by clicking on Yes

28 Step 3. Starting the RIS server process. Click on the Start menu and 'run', type risetup and click ok point the RIS installation folder to a separate partition from the OS

29 Insert the Windows XP SP2 VLK cd, and Tell windows where the XP cd is goingto be (in this case drive F:)

30

31

32 Reboot the computer at this point the Server should now be ready to use a RIS server. windows-noob.com 13/2/2008