Key Fob ZHKF-101. Technical manual

Transcription

1 Key Fob ZHKF-101 Technical manual Revised

2 Content 1 Cautionary notes Features Key Fob ZHKF Key features Endpoints ZigBee Device Object (ZDO) IAS Zone Develco Utility Supported Clusters IAS Zone Device EP 0x Basic Cluster id 0x Attribute Manufacture Specific Attribute...9 ZCL header setting Manufactor code for Develco Products is 0x Identify Cluster id 0x Attribute Commands Power Configuration - Cluster id 0x Attribute IAS Zone - Cluster id 0x Attribute Commands IAS ACE - Cluster id 0x Commands MMI user guide General Arm Home Arm All Arm Night

3 5.5 Disarm Panic Arming response Pairing a new device Pairing a used device (factory reset) General network behaviour Installation Normal Keep alive Network lost Low battery Specifications Contact Information About Develco Products A/S

4 Copyright Develco Products A/S All rights reserved. Develco Products assumes no responsibility for any errors, which may appear in this manual. Furthermore, Develco Products reserves the right to alter the hardware, software, and/or specifications detailed herein at any time without notice, and Develco Products does not make any commitment to update the information contained herein. All the trademarks listed herein are owned by their respective owners. RoHS 4

5 1 Cautionary notes Develco Products A/S reserves the right to make changes to any product to improve reliability without further notice. Develco Products A/S does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under patent rights or the rights of third parties. 5

6 2 Features 2.1 Key Fob ZHKF-101 The Key Fob is a ZigBee HA IAS ACE device. The devices can be used as a remote control for an Intruder Alarm System. The Key Fob has four buttons (Arming, Disarming, Night-arming, and Panic). It is battery powered with two standard AAA batteries. Any changes on the key-inputs will be reported. 2.2 Key features Key features are: IAS Ancillary Control Equipment (ACE). Certified ZigBee Home Automation application profile ZigBee PRO is supported RoHS compliant according to the EU Directive 2002/95/EC. Standard ZigBee Home Automation security and stack settings are used. 6

7 3 Endpoints The device implements the following standard HA devices on different end points. 3.1 ZigBee Device Object (ZDO) End point number 0x00 Application profile Id 0x0000 Application device Id 0x0000 Supports all mandatory clusters 3.2 IAS Zone End point number 0x23 Application profile Id 0x0104 (Home Automation) Application device Id 0x0402 The following clusters are supported on IAS Zone end point Server side IAS Zone Identify Basic Power Configuration Mandatory Optional Client side IAS ACE None 3.3 Develco Utility Application profile Id 0xC0C9 (Develco Products private profile) Application device Id 0x0001 Private profile for internal Develco Products use only. The DevUtil end point support a Develco products specified bootloader. New firmware can be downloaded to the device using the SmartAMM server + SmartAMM client tool. 7

8 Reference documents: r18ZB_CSG-ZigBee-Specification.pdf r03ZB_AFG-ZigBee_Cluster_Library_Specification.pdf r27ZB_HA_PTG-Home-Automation-Profile.pdf r15ZB_ZSE-ZSE-AMI_Profile_Specification.pdf They can all be downloaded from: 8

9 4 Supported Clusters The ZCL General Function Domain clusters in this section are implemented as server clusters. Refer to ZigBee Cluster Library Specification IAS Zone Device EP 0x23 The IAS Zone end point contains the following clusters Basic Cluster id 0x Attribute Id# Name Type Range Man/Opt Relevance and ref. 0x0 ZCLVersion Uint8 Type range M 0x4 ManufacturerName String 0-32 byte O x5 ModelIdentifier String 0-32 byte O x7 PowerSource 8 bit enum Type range M ManufacturerName Develco Products A/S ModelIdentifier ZHKF Manufacture Specific Attribute Id# Name Type Range Man/Opt Relevance and ref. 0x8000 PrimarySwVersion OctetString M SW version ZCL header setting Manufactor code for Develco Products is 0x Identify Cluster id 0x Attribute Id# Name Type Range Man/Opt Relevance and ref. 0x0000 IdentifyTime Uint16 Type range M Commands The identify cluster has 2 commands as server. 9

10 Id# Name Payload Man/Opt Relevance and ref. 0x00 Identify Uint16 - Identify Time (seconds) M 0x01 Identify Query none M The identify cluster has 1 command as client. Id# Name Payload Man/Opt Relevance and ref. 0x00 Identify Query Response Uint16 - Identify Time (seconds) M Power Configuration - Cluster id 0x0001 The power configuration cluster is described in ZigBee Cluster Library Specification Attribute Id# Name Type Range Man/Opt Relevance and ref. 0x0020 BatteryVoltage Uint8 0x00-0xFF O Note: The attribute BatteryVoltage is measuring the battery voltage, in units of 100mV IAS Zone - Cluster id 0x0500 The IAS Zone cluster is described in ZigBee Cluster Library Specification Attribute Id# Name Type Man/Opt Relevance and ref. 0x0000 Zone State 8-bit Enumeration M 16-bit 0x0001 Zone Type Enumeration M 0x0002 Zone Status Uint16 M Hard coded to Not Enrolled The following bits are supported: Bit3: Battery Bit4: Supervision reports Bit5: Restore reports Bit6: Trouble Commands The identify cluster has 2 commands as server. 10

11 Id# Name Payload Man/Opt Relevance and ref. 0x00 Zone Status Change Notification Uint16 bit mask M The following bits are supported: Bit3: Battery Bit4: Supervision reports Bit5: Restore reports Bit6: Trouble When the battery is below 2.2 VDC Bit3: Battery is set high and Zone Status is transmitted to the coordinator IAS ACE - Cluster id 0x0501 The IAS ACE cluster is described in ZigBee Cluster Library Specification. The Cluster is implemented as a client cluster Commands The IAS ACE cluster has 2 commands as client. Id# Name Payload Man/Opt Relevance and ref. 0x00 Arm Uint16 bit mask M 0x04 Panic M Triggered when pressing the Arm, Disarm and Night arm buttons. Triggered when pressing the Panic button The Arm mode client command can contain the following values Arm Mode - Field Value Meaning Relevance and ref. 0x00 Disarming 5.5 Disarm 0x01 Arm Day/Home Zones Only 5.2 Arm Home 0x02 Arm Night/Sleep Zones Only 5.4 Arm Night 0x03 Arm All Zones 5.3 Arm All 11

12 5 MMI user guide 5.1 General User sees green LED shortly blinking after pressing any button this gives a visual feedback of successful pressing. Visual feedback when long key press time has expired. The feedback for long key press is a new green led blink. 5.2 Arm Home User presses Home ARM button Green led blinks shortly User releases Home ARM button Device sends Arm Day/Home Zones Only command Use case 5.7 Arming response is activated 5.3 Arm All User presses Home ARM button Green led blinks shortly After 3s green led blinks shortly to indicate long press User releases Home ARM button Device sends Arm All Zones command to backend Use case 5.7 Arming response is activated 5.4 Arm Night User presses Night ARM button Green led blinks shortly User releases Night ARM button Device sends Arm Night/Sleep Zones Only command to backend Use case 5.7 Arming response is activated 5.5 Disarm User presses DISARM button Green led blinks shortly User releases DISARM button Device sends Disarm command to backend Use case 5.7 Arming response is activated 12

13 5.6 Panic User presses PANIC button Green led blinks shortly After 2s green led blinks shortly to indicate long press User releases PANIC button Device sends Panic command to backend If command is delivered to backend, green led turns on for 1 second If command is not delivered to backend within 5s, the red led blinks quickly 3 times 5.7 Arming response Arm response code All Zones Disarmed Only Day/Home Zones Armed Only Night/Sleep Zones Armed All Zones Armed Invalid Arm/Disarm Code No response within 5s Blink pattern green led turns on for 1 second red led turns on for 1 second red led turns on for 1 second red led turns on for 1 second red led blinks quickly 3 times red led blinks quickly 3 times 5.8 Pairing a new device User presses any button to activate the device to start searching for networks User sees red LED slow blinking for while network search If no network is found within 15min, the device stops blinking and goes to sleep this use case can then be reinitiated at any time pressing any key If network found, the device stops blinking Pairing process requires no additional user interactions 5.9 Pairing a used device (factory reset) User inserts batteries into a device Within the first 60s, the user presses and holds upper right (DISARM) button Green LED blinks shortly After 5 seconds, the red led blinks fast Menu factory reset is selected. The user SHALL releases the DISARM button The device is reset to factory default 13

14 6 General network behaviour 6.1 Installation When the device is virgin and powered for the first time it will start looking for a ZigBee PAN Coordinator or router to join. The device will scan each ZigBee channel starting from 11 to 24. The LED will flash once every second until it joins a device. #Scan mode - 1 #Sleep mode #Scan mode - 2 #Sleep mode #Scan mode - 2 Scan all 16 ZigBee channel until join network or 15 MCU is in sleep mode (Radio off) 15 minutes Scan all 16 ZigBee ch x 1 or until join network MCU is in sleep mode (Radio off) 15 minutes Scan all 16 ZigBee ch x 1 or until join network ~ 30 seconds minutes ~ 30 seconds The device will start up using scan mode 1. To increase battery lifetime when the device is joining a network for the first time a scan mode 2 will be used after scan mode 1 has expired. Scan mode 1 it will only be executed one time when the device is powered. If the user invokes EZ-mode it will start scanning the next 3 minutes In section 5 MMI it is explained how to put the device into a join or leave network mode. Network settings are stored in NV-memory are after a power cycle the device re-join the same network. If the device has to join a new PAN coordinator the MMI menu supports a Reset To Factory Fresh Settings mode. This will erase all current network information. 6.2 Normal Keep alive The device is sending a keep alive message to the PAN coordinator every 15 minute to verify that the device is still connected to the network Network lost If no keep alive responses are received 5 times in a row (Worst case 1h15m), the devices will start scanning as specified in the table below. When the device is in scan mode the LED will flash once every second until it re-joins the network. According to the ZigBee specification TX is NOT allowed to be enabled all the time and a TX silent period has to be defined. #Scan mode - 1 #Sleep mode #Scan mode - 2 #Sleep mode #Scan mode

15 Scan current ch 3 times Scan remaining 15 MCU is in sleep mode (Radio off) 15 minutes Scan current ch 3 times Scan remaining 15 MCU is in sleep mode (Radio off) 15 minutes Scan current ch 3 times Scan remaining 15 ch 1 ch 1 time ch 1 time time Scan all 16 ch 3 times 6.3 Low battery The current battery voltage can be read from the power configuration cluster described in section The attribute BatteryVoltage is measuring the battery voltage, in units of 100mV. 15

16 7 Specifications Dimensions Colour Battery Battery life 72 x 30 x 18 mm Black 2 x AAA, exchangeable Up to 2 years Operation temperature 0 to + 50 C Sensitivity Output power -92 dbm +3 dbm 16

17 8 Contact Information Technical support: Please contact Develco Products for support. Sales: Please contact Develco Products for information on prices, availability, and lead time. 17

18 9 About Develco Products A/S Energy efficiency, Savings & Comfort Develco Products provides communication systems for AMR, AMI and Smart Metering. Develco Products presents a complete solution facilitating the remote control of appliances via intelligent electricity meters or gateways also capable of communicating with other meters. SmartAMM SmartAMM is a modular concept securing a flexible and forward-looking Smart House solution. SmartAMM makes it possible to monitor and control your home s electrical appliances and energy consumption via smart meters. SmartAMM combines automated meter reading with home automation, and includes: AMR (Automated Meter Management) for existing metering solutions AMR for meter manufacturers Communication modules for integration in meters or appliances (ZigBee, Z-Wave, PLC, GPRS, GSM and others) Data concentrators with back-office communication (GPRS, SMS, Internet, Fiber, PLC) Home Automation Benefits Cheap and reliable metering Reduced energy consumption Optimized energy consumption (peak level out) Avoidance of blackouts Sale of extra services: o Readout of several meters by diverse manufacturers and types (water, heating, gas, electricity) o Surveillance o Alarms Selected cases DONG Energy Gas (AMR of gas meters via GPRS data concentrator) Dong Energy Power (control and alarm via SmartRead power meter) EnergiMidt (SmartAMM concept covering metering (water & heating) and energy display via power meters as well as home automation. Everything integrated into one module and installed in the Echelon PLC power meter). 18