Barcode Scanner. Model no. NuScan User s Manual
|
|
- Nicholas Jenkins
- 6 years ago
- Views:
Transcription
1 Barcode Scanner Model no. NuScan 5000 User s Manual
2 FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Limited Warranty No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein or for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval.
3 Table of Contents 1. INTRODUCTION 2~3 2. INSTALLATION 4~6 3. SET UP FROM BAR CODE LABEL.7 Operating Settings.8 Sensor Mode 8~9 USB Country Keyboard Types..10~11 1D Symbologies On/Off 12~14 2D Symbologies On/Off 15~16 Symbologies Set Up..17~23 Termination String Setup Bar Codes.24 1
4 Introduction 2
5 NUSCAN 5000 barcode scanner, using 2D engine, combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install drivers to operate. All the operating parameters are programmed by bar code programming menu and stored in non-volatile RAM which can retain the settings after power is turned off. When a barcode is successful decoded, the blue LED light of the scanner will turn on and off. The scanner will beep once. 3
6 Installation Insert the plug on the free end of the Communications Cable into the appropriate connector on the PC as below described: USB cable Connection(USB HID): Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode below. This will reset the scanner to its factory defaults settings in USB interface. 1. Be sure that PC is turned OFF 2. Connect scanner cable to the USB port on the PC. 3. Ensure that all connections are secure. Turn on your PC. 4. And please operate the scanner under the right software application. 5. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 6. On successful decode, the blue LED light will turn on and off. The scanner will beep once. And will show the barcode data on the screen. 4
7 Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode. This will reset the scanner to its factory defaults settings. ** Code Programming ON Load Factory Default (Pro CMD : ) 5
8 Operation Tip Do not hold the scanner directly over a barcode at 90. Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult. Practice a few times to find what range of angles works best. Maintenance Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy. Wipe the scanner window gently with a lens tissue or other material suitable for cleaning optical material. Do not spray water or other cleaning liquids directly onto the window. 6
9 Setup from Bar Code Label 7
10 Operating settings Trigger Mode Auto-Sensing Pro CMD : Pro CMD : Sensor Mode Timeout Sensor Mode High Sensitivity (= 8) Pro CMD : Pro CMD : Normal Sensitivity (= 11) Low Sensitivity (= 14) Pro CMD : Pro CMD : Enhanced Sensitivity (= 5) Pro CMD :
11 Allow Reading All = enable to read all symbologies and programming codes Prohibit Reading All = allow reading programming codes only. Pro CMD : Pro CMD : Allow Reading All 1D Prohibit Reading All 1D Pro CMD : Pro CMD : Allow Reading All 2D Prohibit Reading All 2D Pro CMD : Pro CMD :
12 USB Country Keyboard Types The keyboard arrangements and country codes vary in different countries. Refer country codes to the table USB Country Keyboard Types. Follow the steps mentioned below to program. 1. Code Programming ON 2. Select Country Code 3. Read digit codes (according to country code) 4. Save 5. Code Programming OFF ** Code Programming ON Select Country Code ( Pro CMD : ) Save (Pro CMD: ) Country/Language Number Country/Language Number U.S. 0 Netherlands(Dutch) 14 Belgium 1 Norway 15 Brazil 2 Poland 16 Canada(French) 3 Portugal 17 Czech 4 Romania 18 Denmark 5 Russia 19 Finland(Swedish) 6 Slovakia 21 France 7 Spain 22 Germany/Austria 8 Sweden 23 Greece 9 Switzerland(German) 24 Hungary 10 Turkey F 25 Israel(Hebrew) 11 Turkey Q 26 Italy 12 U.K 27 Latin-American 13 Japan 28 10
13 Digit Code It is must to be read save after read digit code. 0 (Pro CMD : ) 5 (Pro CMD : ) 1 (Pro CMD : ) 6 (Pro CMD : ) 2 (Pro CMD : ) 7 (Pro CMD : ) 3 (Pro CMD : ) 8 (Pro CMD : ) 4 (Pro CMD : ) 9 (Pro CMD : ) 11
14 1D Symbologies On/Off 1 CODE 39 ENABLE CODE 39 CODE 39 DISABLE Pro CMD : Pro CMD : ENABLE * Sign DISABLE * Sign CODE 93 Pro CMD: Pro CMD: CODE 93 - ENABLE CODE 93 - DISABLE Pro CMD : Pro CMD : CODE ENABLE CODE 128 CODE DISABLE Pro CMD : Pro CMD : CODABAR - ENABLE CODABAR CODABAR - DISABLE Pro CMD : Pro CMD : INTERLEAVED 25 - INTERLEAVED INTERLEAVED 25 - ENABLE 25 DISABLE Pro CMD : Pro CMD :
15 1D Symbologies On/Off 2 UPC-A ENABLE UPC/EAN UPC-A DISABLE Pro CMD : Pro CMD : UPC-E ENABLE UPC-E DISABLE Pro CMD : Pro CMD : EAN-8 ENABLE EAN-8 DISABLE Pro CMD : Pro CMD : EAN-13 ENABLE EAN-13 DISABLE Pro CMD : Pro CMD : EAN-128 ENABLE UCC/EAN EAN-128 DISABLE Pro CMD : Pro CMD : ENABLE Industrial 25 DISABLE Pro CMD: Pro CMD: ENABLE Matrix 25 DISABLE Pro CMD: Pro CMD:
16 (Pro CMD: ) 1D Symbologies On/Off 3 MSI Plessy ENABLE MSI Plessy MSI Plessy DISABLE Pro CMD : Pro CMD : Code 11 ENABLE Code 11 Code 11 DISABLE Pro CMD : Pro CMD : ISBN ENABLE ISBN ISBN DISABLE Pro CMD : Pro CMD : ENABLE UCC/EAN Composite DISABLE Pro CMD : Pro CMD :
17 2D Symbologies On/Off - 1 Data Matrix -ENABLE Data Matrix Data Matrix -DISABLE Pro CMD : Pro CMD : **Forward Direction Barcode Only Both Pro CMD: Pro CMD: Backward Direction Barcode Only Pro CMD : QR Code -ENABLE QR Code QR Code -DISABLE Aztec -ENABLE Aztec Aztec -DISABLE Pro CMD : Pro CMD :
18 PDF 417ENABLE PDF 417 PDF 417 DISABLE Pro CMD : Pro CMD : **Forward Direction Barcode Only Both Pro CMD: Pro CMD: Backward Direction Barcode Only Pro CMD:
19 ** Code Programming OFF Symbologies Set Up - 1 TRANSMIT UCC/EAN-8 UPC/EAN -8 CHECK ENABLE CHECK Digit TRANSMIT UCC/EAN-8 CHECK DISABLE Pro CMD : Pro CMD : UPC/EAN -13 CHECK Digit TRANSMIT UCC/EAN-13 CHECK ENABLE TRANSMIT UCC/EAN-13 CHECK DISABLE Pro CMD : Pro CMD : ISBN Transmit 13 digits Transmit Transmit 10 digits Pro CMD : Pro CMD : UPC-E CHECK Digit TRANSMIT UPC-E CHECK ENABLE TRANSMIT UPC-E CHECK DISABLE Pro CMD : Pro CMD : UPC-A CHECK Digit TRANSMIT UPC-A CHECK ENABLE TRANSMIT UPC-A CHECK DISABLE Pro CMD : Pro CMD :
20 NO Check, Transmit All Symbologies Set Up - 2 Interleaved 25 CHECK Digit Check, Transmit No Check Pro CMD : Pro CMD : Check, Transmit All Pro CMD : NO Check, Transmit All Matrix 25 CHECK Digit Check, Transmit No Check Pro CMD : Pro CMD : Check, Transmit All Pro CMD : Code 39 FULL ASCII -ENABLE CODE 39 FULL ASCII Code 39 FULL ASCII -DISABLE Pro CMD : Pro CMD : CODE 39 Check, Transmit No NO Check, Transmit All CHECK Digit Check Pro CMD : Pro CMD : Check, Transmit All Pro CMD :
21 Symbologies Set Up 3 NO Check, Transmit All CODEBAR CHECK Digit Check, Transmit No Check Pro CMD : Pro CMD : Check, Transmit All Pro CMD : Transmit Both Start & Stop Character Transmit Neither Start & Stop Character Pro CMD: NO Check, Transmit All CODE 93 CHECK Digit Pro CMD: Check, Transmit No Check Pro CMD : Pro CMD : Check, Transmit All Pro CMD :
22 Symbologies Set Up - 4 NO Check, Transmit All MSI Plessy CHECK Digit Double Check Digits, MOD10/MOD11 Pro CMD : Pro CMD : Single Check Digit,MOD10 NO Transmit Check Digits Pro CMD : Pro CMD : Double Check Digits, MOD10/MOD10 Transmit Check Digits Pro CMD : Pro CMD :
23 Symbologies Set Up - 5 NO Check, Transmit All Code 11 CHECK Digit Single Check Digit MOD11(Len <= 10) Double Check Digits MOD11/MOD11 (Len > 10) Pro CMD : Pro CMD : Single Check Digit,MOD11 Single Check Digit MOD11(Len <= 10) Double Check Digits MOD11/MOD9 (Len > 10) Pro CMD : Pro CMD : Double Check Digits, MOD10/MOD10 Do not Transmit Check Digits Pro CMD : Pro CMD : Transmit Check Check Digits Pro CMD :
24 Symbologies Set Up 6 EXPAND EAN-8 TO EAN-13 ENABLE UPC/EAN FORMATIN G EXPAND EAN-8 TO EAN-13 DISABLE Pro CMD : Pro CMD : Digits Addenda ENABLE UPC/EAN-8 Addenda Code 2 Digits Addenda DISABLE Pro CMD : Pro CMD : Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD : Pro CMD : Digits Addenda ENABLE UPC/EAN-13 Addenda Code 2 Digits Addenda DISABLE Pro CMD : Pro CMD : Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD : Pro CMD :
25 Symbologies Set Up 7 2 Digits Addenda ENABLE UPC-E Addenda Code 2 Digits Addenda DISABLE Pro CMD : Pro CMD : Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD : Pro CMD : UPC-E Default 0 Do Not Transmit Transmit Pro CMD: Digits Addenda ENABLE UPC-A Addenda Code Pro CMD: Digits Addenda DISABLE Pro CMD : Pro CMD : Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD : Pro CMD :
26 TERMINATION STRING SETUP BAR CODES Step 1 STRING# 1 TERMINATION CHAR - CR Step 2 Pro CMD : Pro CMD : Step3 Pro CMD :
Laser Barcode Scanner Model no. LS6007 FS5027
Laser Barcode Scanner Model no. LS6007 FS5027 User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
More informationWireless Laser Barcode Scanner ils 6300BU. User s Manual
Wireless Laser Barcode Scanner ils 6300BU User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
More informationLaser Barcode Scanner ARP Nr User s Manual
Laser Barcode Scanner ARP Nr. 853782 User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
More informationNuscan 3200 Optical Laser Barcode Scanner
Nuscan 3200 Optical Laser Barcode Scanner Programming Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
More information2D Imaging Barcode Scanner GLLS. Programming Guide. Advanced Handheld High-Speed Laser Scanner
2D Imaging Barcode Scanner GLLS Programming Guide 1 Advanced Handheld High-Speed Laser Scanner Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0
More informationMS810 Laser Scanner. Product Reference Guide. Rev. A
MS810 Laser Scanner Product Reference Guide Rev. A 1 Preface About This Manual This manual explains how to install, operate and maintain the Unitech MS810 Laser Scanner. No part of this publication may
More informationMS810 Laser Scanner. Product Reference Guide. Rev. A
MS810 Laser Scanner Product Reference Guide Rev. A 1 Preface About This Manual This manual explains how to install, operate and maintain the Unitech MS810 Laser Scanner. No part of this publication may
More information2D Imaging Barcode Scanner GLLS. Programming Guide. Advanced Handheld High-Speed Laser Scanner
2D Imaging Barcode Scanner GLLS Programming Guide 1 Advanced Handheld High-Speed Laser Scanner Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0
More informationNLS-FM208 Industrial Scanner User Guide
NLS-FM208 Industrial Scanner User Guide Pre-release Version 20090826 目录 About This Reference 1 Introducation 1 Graphic Emphasis 1 Chapter Description 1 Getting Start 2 Introducation 2 Familiar with FM200
More informationnlscan.com Tools Exposure Imaging Mode ** Normal Exposure Mode Pro CMD Reflections Eliminating Mode Pro CMD Page 36
Programming the Engine Exposure Imaging Mode ** Normal Exposure Mode Pro CMD 0321000 Reflections Eliminating Mode Pro CMD 0321010 Page 36 Programming the Engine Default Factory Default Read Load All Factory
More informationFM420 Fixed Mount Barcode Scanner Quick Start V1.0
FM420 Fixed Mount Barcode Scanner Quick Start V1.0 Revisions Version Description Date V 1.0 Support as from FM420 firmware V 3.06.021 and higher. 19-10-2010 Content Getting to Start Unpacking... E-01 Main
More informationSetting code User Manual
Powered By Setting code User Manual Version 2.02.007 Tel: 510 490 3888 Fax: 510 490 3887 http://www.newlandna.com Contents CHAPTER 1 SETTING CODE TURN-ON/OFF..... 1 CHAPTER 2 SETTING CODE STEP-BY-STEP
More informationDisclaimer. Please read through the manual carefully before using the product and operate it
ONEBRAND,ONESOLUTI ON 2D Handhel dbar codescanner UserManual Disclaimer Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you
More informationNLS-FM210 Embedded 2D Barcode Scanner Integration Guide
NLS-FM210 Embedded 2D Barcode Scanner Integration Guide Pre-release version 09/08/26 Content About This Reference 1 Introduction 1 Graphic Emphasis 1 Getting Started 2 Introduction 2 Familiar with FM210
More informationMK D Imager Barcode Scanner Configuration Guide
MK-5500 2D Imager Barcode Scanner Configuration Guide V1.4 Table of Contents 1 Getting Started... 3 1.1 About This Guide... 3 1.2 Barcode Scanning... 3 1.3 Factory Defaults... 3 2 Communication Interfaces...
More informationSerial Programming Command Manual
Serial Programming Command Manual Disclaimer The information in this publication does not represent a commitment on the part of Newland. Newland shall not be liable for technical or editorial errors or
More informationXL D Barcode Scanner User's Manual V1.0
XL-3100 2D Barcode Scanner User's Manual V1.0 Table of Contents Revision History...-3- Chapter 1 Getting Started... 1 Introduction... 1 About This Guide... 2 Barcode Scanning... 2 Configuring the XL-3100...
More information2D Imaging Barcode Scanner. Programming. Advanced Handheld High Speed Laser Scanner
2D Imaging Barcode Scanner Programming 1 Advanced Handheld High Speed Laser Scanner This Programming Guide is intended for: 2D Image Handheld Scanner: Z 3272 Plus Revision History Changes to the original
More informationFactory Default Configuration. Factory Default Configuration
Factory Default Configuration Trigger Mode Terminator Factory Default Configuration Setup Code *open Parameter code close Parameter code Product information 1. Serial Port Using Serial Portread moudle
More information2D Imaging Barcode Scanner. Programming. Advanced Handheld High Speed Laser Scanner
2D Imaging Barcode Scanner Programming 1 Advanced Handheld High Speed Laser Scanner This Programming Guide is intended for: 2D Image Handheld Scanner: Z 3172 Plus 2D Image Hands Free Scanner: Z 8072,
More information2D Imaging Barcode Scanner GLLS. Programming Guide. Advanced Handheld High-Speed Laser Scanner
2D Imaging Barcode Scanner GLLS Programming Guide 1 Advanced Handheld High-Speed Laser Scanner This Programming Guide is intended for: 2D Image Handheld Scanner: Z-3172 Plus, Z-3272 Series 2D Image Hands-Free
More information2D Imaging Barcode Scanner. Programming. Advanced Handheld High-Speed Laser Scanner
2D Imaging Barcode Scanner Programming 1 Advanced Handheld High-Speed Laser Scanner This Programming Guide is intended for: 2D Image Engine: Z-5212 Revision History Changes to the original manual are
More information2D Barcode Reader User Guide V 1.2.1
2D Barcode Reader User Guide V 1.2.1 Table of Contents 1 Getting Started... 3 1.1 About This Guide... 3 1.2 Barcode Scanning... 3 1.3 Factory Defaults... 3 1.4 Firmware Version Number... 3 2 Communication
More informationIf you want to do other configurations please refer to below programming barcodes.
NT-1202 Quick Setup Guide This is 1D&2D plug and play model if you use a US keyboard. If you use other type of keyboard, plug the USB cable on your device, setup keyboard language before you use it. (refer
More informationAdvanced Handheld High-Speed Laser Scanner
GLLS 1 Advanced Handheld High-Speed Laser Scanner Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 2015/03/03 Initial release 1.1 2015/04/15 Added
More informationBarcode BC-29. Decoder & Platform. Programming Manual
Barcode BC-29 Decoder & Platform Programming Manual CONTENTS Getting Started...2 Setting Procedures...3 Setting Flow Chart......4 Group 1 : Multi Validation....5 Group 2 : Hold Time...6 Group 3: Scan Mode
More informationNLS-EM3095 Embedded 2D Barcode Scan Engine. User Guide
NLS-EM3095 Embedded 2D Barcode Scan Engine User Guide Disclaimer 2013 Fujian Newland Auto-ID Tech. Co., Ltd. All rights reserved. Please read through the manual carefully before using the product and operate
More informationBD-6500BT Bluetooth 2D Barcode Scanner Configuration Guide
BD-6500BT Bluetooth 2D Barcode Scanner Configuration Guide V 2.1 Table of Contents 1 Getting Started. 3 1.1 About This Guide.. 3 1.2 Barcode Scanning.. 3 1.3 Factory Defaults.. 3 1.4 Pairing Cradle 4 1.5
More informationSGBS-310-2D 2D Barcode Scanner Integration Guide
SGBS-310-2D 2D Barcode Scanner Integration Guide Table of Contents 请更换节标题 Content About this guide Introduction... 1 Chapter Description... 1 Graphic Notations... 1 Introduction... 2 Highlights of the
More information2DScan TM Barcode Scanner
2DScan TM Barcode Scanner Quick Start Manual Default Check Version FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
More informationWireless 2D Pocket barcode scanner
* Wireless 2D Pocket barcode scanner Quick Guide Model no.: idc9507l Introduction Designed primarily for P.O.S. retail environments, the idc9507l is a wireless pocket barcode scanner that allows you to
More informationGS500 2D Area-Imaging Scanner. User Manual
GS500 2D Area-Imaging Scanner User Manual Table of Contents Table Of Contents... 1 Chapter 1 Getting Started... 6 About This Guide... 6 Barcode Scanning... 6 Barcode Programming... 6 Factory Defaults...
More informationPOSSAFE LQ300 BARKOD OKUYUCU. Configuration Manual
POSSAFE LQ300 BARKOD OKUYUCU Configuration Manual System function setting Factory Default setting All scanners have a factory default settings, scan "Factory Default "bar code, will make the scanner all
More information2DScan FX100 Barcode Scanner Scanner User's Manual rev.b
2DScan FX100 Barcode Scanner Scanner User's Manual 80108506-001 rev.b Table of Contents 请更换节标题 Content About this guide Idtech Auto-ID Support Center... 2 Getting to Start Introduction... 3 Unpacking...
More informationRIOSCAN CCD barcode scanner
RIOSCAN CCD barcode scanner Quick Guide M o de l no: i CR6307AS Introduction Designed primarily for smartphone, the icr6307as is a CCD barcode scanner that allows you to scan various barcoded items and
More informationwireless barcode scanner X-620 User Manual
wireless barcode scanner X-620 User Manual V:1.0 Performance Strong decoding capability Rugged housing design Proprietary intellectual property Comfortable and convenient to use long life time button--3
More informationInstallation Guide Solar Power Bluetooth Hands-free Car Kit GBHFK231
Installation Guide Solar Power Bluetooth Hands-free Car Kit 1 GBHFK231 Table of Contents Package Content 4 Requirements 5 Device Overview 6 Charging Your Car Kit 7 Recommended Way of Using Your Car Kit
More informationFM420 Embedded 1D/2D Barcode Scanner Integration Guide
FM420 Embedded 1D/2D Barcode Scanner Integration Guide Revisions Version Description Date Version 1.0 Support as from FM420 firmware Version 3.06.021 and higher. 25-08-2010 Version 1.1.1 Modifiy the introduction
More informationThis confirguration including four steps,please scan below codes one by one.
Wireless 2D Barcode Scanner Overview Netum wireless 2D model integrates a high-performance processer with an effective decoding board, combining a fast decoding speed. High precision and a high anti-interference
More informationEM2037 2D Barcode Scan Engine. Programming Manual
EM2037 2D Barcode Scan Engine Programming Manual Revisions Version Description Date V 1.0 Initial Version. 2011-11-23 Disclaimer 1999-2011 by Fujian Newland Auto-ID Tech. Co., Ltd, All rights reserved.
More information2D Wired Barcode Scanner Overview
2D Wired Barcode Scanner Overview Netum wired 2D Plug and Play barcode scanner integrates a high performance processer with an effective decoding board, combining a fast decoding speed. IP67 waterproof
More informationKeyboard Language In order to let scanner upload the codes in a correct way, you have to set the keyboard language before you use it.
2.4G Wireless Barcode Scanner Overview Netum 2.4G wireless model integrates a high-performance processer with an effective decoding board, combining a fast decoding speed. High precision and a high anti-interference
More information2DScan TM Barcode Scanner User s Manual
2DScan TM Barcode Scanner User s Manual 80108502-001 rev.a FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
More informationLS-1000 Series Laser Barcode Scanner User s Manual Rev. A0
LS-1000 Series Laser Barcode Scanner User s Manual Rev. A0 FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions
More informationBS8050-3V Piranha (1D) Barcode Scanner. User Guide
BS8050-3V Piranha (1D) Barcode Scanner User Guide Disclaimer 2015 Fujian Newland Auto-ID Tech. Co., Ltd. All rights reserved. Please read through the manual carefully before using the product and operate
More informationNT-1228BL. Quick Setup Guide V Connection Mode. Working via Bluetooth. Barcode Programming
NT-1228BL V18.7.12 Quick Setup Guide This model can work both via USB cable or via bluetooth. Connection Mode Working via USB cable Get Started: Connect scanner with your device via USB cable. If you use
More informationRT206 User Guide. RT206 OEM 2d Scan Engine User Guide
RT206 OEM 2d Scan Engine User Guide Table Of Contents Chapter 1 Getting Started... 1 About This Guide... 1 Connecting EVK to PC... 1 Barcode Programming... 2 Factory Defaults... 2 Custom Defaults... 3
More information2D Wired Barcode Scanner Overview. Keyboard Language In order to let scanner upload the codes in a correct way, you have to set the keyboard language.
2D Wired Barcode Scanner Overview Netum wired 2D Plug and Play barcode scanner integrates a high-performance processer with an effective decoding board, combining a fast decoding speed.the device can easily
More informationRT209 OEM 2d Scan Engine User Guide
RT209 OEM 2d Scan Engine User Guide Table Of Contents Chapter 1 Getting Started... 1 About This Guide... 1 Connecting EVK to PC... 1 Barcode Scanning... 1 Barcode Programming... 1 Custom Defaults... 3
More informationLIMITATION OF LIABILITY
FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
More informationAPPENDIX E COMMAND BARCODES
APPENDIX E COMMAND BARCODES Scan command barcode(s) to quickly configure the CHS 7X or 7XRx. By default, the CHS is in HID mode as a Keyboard device. IMPORTANT! Make sure the CHS is not connected to a
More informationIf you want to do other configurations please refer to below programming barcodes.
NT-M3 Quick Setup Guide This is a plug and play model if you use a US keyboard. If you use other type of keyboard, plug the USB cable on your device, setup keyboard language before you use it. (refer to
More informationGetting Familiar with Your FuzzyScan
Getting Familiar with Your FuzzyScan Thank you for choosing Cino FuzzyScan Imager. All FuzzyScan imagers deliver world-class performance for a broad range of applications to unleash your productivity.
More information1D IMAGER MODELS - 7Ci, 7Di, D700
COMMAND BARCODES 1D IMAGER MODELS - 7Ci, 7Di, D700 This document pertains to the following 7Ci, 7Di, D700: The part number (P/N) is labeled inside the battery compartment for the CHS 7 Series. Ci Di Model
More informationModel NT-1203 With SPP Mode
Model NT-1203 With SPP Mode Get Started: This is 1D and 2D bluetooth scanner. Follow below "bluetooth connection" instruction to pair with your device and then setup the keyboard language (if you US keyboard,
More information4620, Quick Start
4620, 5620 Quick Start Getting Started Turn off power before connecting the base, then power up the computer once the base is fully connected. When the base is connected and powered up, put the imager
More informationNCR Realscan 7837 High-Performance Scanners. User s Guide Issue A
NCR Realscan 7837 High-Performance Scanners User s Guide 497-0427357 Issue A Table of Contents Chapter 1 - Getting Started About This Manual... 1-1 Unpacking the Scanner... 1-2 RealScan 7837 High-Performance
More informationThis configuration including four steps. Please scan below codes one by one.
Bluetooth Wireless Barcode Scanner Overview Netum bluetooth wireless model integrates a high-performance processer with an effective decoding board, combining a fast decoding speed. High precision and
More information2D Scan Engine Confguration Guide. 2D Barcode Scanner Configration Guide
2D Barcode Scanner Configration Guide 1 Table of Contents USB Settings USB Keyboard Mode...6 (A1) USB Downloader Mode...6 (A2) USB Virtual COM One Way Mode...6 (A3) USB Native Two Way Mode...6 (A4) USB
More informationIf you want to have other configurations please refer to below programming barcodes. Check Scanner Version
NT-1228BL V18.7.12 Quick Setup Guide This model can work both via USB cable or via bluetooth. Connection Mode Working via USB cable Get Started: Connect scanner with your device via USB cable. If you use
More information2D Image Handheld Scanner
1 Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 9/6/2018 Initial release i Important Notice No warranty of any kind is made in regard to this
More informationINFINEA OMNI For ipad
INFINEA OMNI For ipad Air INFINEA OMNI USER MANUAL CONTACT INFORMATION Web: General enquiries: Support: www.stimare.net info@stimare.net support@stimare.net United States: 2001 Massachusetts Ave NW, Washington,
More informationCode Reader 1000/1400/8000 Configuration Guide
Code Reader 1000/1400/8000 Configuration Guide Code Reader 1000 Code Reader 1400 Code Reader 8000 1 Table of Contents USB Settings USB Keyboard Mode...6 (A1) USB Downloader Mode...6 (A2) USB Virtual COM
More informationIf you want to do other configurations please refer to below programming barcodes.
NT-W8 V18.9.1 Quick Setup Guide This model can work both via USB cable or 2.4G receiver. Connection Mode Working via USB cable Get Started: Connect scanner with your device via USB cable. If you use US
More information2D Image Hands-Free Scanner
8072 1 Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 03/24/2016 Initial release i Important Notice No warranty of any kind is made in regard
More information1. Camera View. 2. First Time Use
1. Camera View 1. USB Terminal 2. Micro SD Slot 3. Speaker 4. Lens 5. Microphone 6. Status Screen 7. Shutter Button 8. Power Button 9. Mode Button 10. Microphone 11. LED Indicator 12. Tripod Screw Hole
More informationUser s Guide. Linear Imager
User s Guide 3200 Linear Imager Disclaimer Hand Held Products, Inc. ( Hand Held Products ) reserves the right to make changes in specifications and other information contained in this document without
More informationFS02 user manual. HID mode for IOS 1. Turn on the barcode reader, and read below barcodes sequence, the blue LED will flash rapidly.
FS02 user manual HID Mode for IOS HID mode for IOS 1. Turn on the barcode reader, and read below barcodes sequence, the blue LED will flash rapidly. 2. Enable the bluetooth of IOS to pair with the barcode
More informationRT-AX95U Wireless-AX11000 Tri Band Gigabit Router
RT-AX95U Wireless-AX11000 Tri Band Gigabit Router Quick Start Guide E13976 / First Edition / February 2018 Package contents RT-AX95U Wireless Router 8 * wireless antennas AC adapter Network cable (RJ-45)
More informationIPDA014-2D. Embedded 2D Barcode Scan Engine. User Guide
IPDA014-2D Embedded 2D Barcode Scan Engine User Guide 1 Table Of Contents Chapter 1 Getting Started...8 Introduction...8 About This Guide...8 Barcode Scanning...9 Barcode Programming...9 Factory Defaults...9
More informationNT-1200 CCD Wired Barcode Scanner Overview
NT-1200 CCD Wired Barcode Scanner Overview Netum wired CCD Plug and Play barcode scanner integrates a high-performance processer with an effective decoding board, combining a fast decoding speed. IP67
More informationFM420 Embedded 1D/2D Barcode Scanner Integration Guide
FM420 Embedded 1D/2D Barcode Scanner Integration Guide Revisions Version Description Date V 1.0 Support as from FM420 firmware Version 3.06.021 and higher. 20100825 V 1.1.1 V 1.1.2 Modifiy the introduction
More informationOwner s Manual. DVI USB KVM Switch with Audio. Models: B004-DUA2-K-R, B004-DUA4-K-R
Owner s Manual DVI USB KVM Switch with Audio Models: B004-DUA2-K-R, B004-DUA4-K-R Package Contents 2 System Requirements 2 Optional Accessories 3 Features 3 Installation 4 Operation 5 Warranty and Product
More informationDIGIT III Manual. Manual Version 1.3
DIGIT III Manual The AirTurn DIGIT III is an 8-button rechargeable Bluetooth multi-function remote control. The DIGIT III works with most Bluetooth 4.0 tablets and computers, including PC, Mac, Android
More informationDIGIT II Manual. The AirTurn DIGIT II is a 5-button Bluetooth rechargeable multifunction
DIGIT II Manual The AirTurn DIGIT II is a 5-button Bluetooth rechargeable multifunction remote controller using the HID profile. The remote works with all known Bluetooth hosts that support HID including
More information000A1 Display inward character string(custom) USB-HID Single not triggered Not:CCD inapplicability Continuous Scan Mode
000A0 Version(custom) 000A1 Display inward character string(custom) 000A2 Display series number (custom) 000B0 Factory 000600 PS2 000601 RS-232 000602 USB-HID 013300 Scan Mode 013301 Single not triggered
More informationDecoding dept & Min Barcode width. Operating Temperature. Humidity. Safety. Drop Test Fast Scan Water Proof. Decoding dept & Min Barcode width
KP1101 ADVANCE PLUS 1D LASER Laser 82 x 67 x 168mm 168 gr RJ45 8Pin connector Bepper HID Keyboard Optional: RS232, USB Virtual COM 645-660 nm Laser Diode 200 Read /sec Skew ±65 - Pitch ±65 - Roll ±42 25%
More informationPortable Hard Drive USB 2.0 User Guide
Portable Hard Drive USB 2.0 User Guide English Contents Introduction 3 Connecting Portable Hard Drive 3 Storing and Transferring Data 4 Disconnecting Portable Hard Drive 5 Technical Support 6 Limited Warranty
More informationChapter 1 : FCC Radiation Norm...3. Chapter 2 : Package Contents...4. Chapter 3 : System Requirements...5. Chapter 4 : Hardware Description...
Table of Contents Chapter 1 : FCC Radiation Norm...3 Chapter 2 : Package Contents...4 Chapter 3 : System Requirements...5 Chapter 4 : Hardware Description...6 Chapter 5 : Charging Your Keychain...7 Chapter
More informationBTScan. Quick Start Manual. ID TECH Walker Street (714) P/N: Rev.B
BTScan TM Quick Start Manual ID TECH 10721 Walker Street (714) 761-6368 www.idtechproducts.com P/N: 80126501-001 Rev.B FCC WARNING STATEMENT This equipment has been tested and found to comply with the
More informationInstallation Guide 2/4-Port HDMI Multimedia KVMP Switch with Audio GCS1792 / GCS1794 PART NO. M1085 / M1086
Installation Guide 2/4-Port HDMI Multimedia KVMP Switch with Audio 1 GCS1792 / GCS1794 PART NO. M1085 / M1086 2 2009 IOGEAR. All Rights Reserved. PKG-M1085 / M1086 IOGEAR, the IOGEAR logo, MiniView, VSE
More informationFM420 Embedded 1D/2D Barcode Scanner Integration Guide
FM420 Embedded 1D/2D Barcode Scanner Integration Guide Revisions Version Description Date Version 1.0 Support as from FM420 firmware Version 3.06.021 and higher. 25-08-2010 Version 1.1.1 Version 1.1.2
More informationOPERATING INSTRUCTIONS POWERSMART 10 10,000 MAH PORTABLE POWER PLEASE READ BEFORE OPERATING THIS EQUIPMENT
POWERSMART 10 10,000 MAH PORTABLE POWER OPERATING INSTRUCTIONS PLEASE READ BEFORE OPERATING THIS EQUIPMENT HALO POWERSMART 10 Thank you for choosing HALO. Innovative and easy to use, the HALO POWERSMART
More information530-2D-USB 2D Scanner High Speed Imaging USB Bar Code Scanner
530-2D-USB 2D Scanner High Speed Imaging USB Bar Code Scanner Worth Data USB 2D Bar Code Scanner - Scan 1D & 2D Matrix Bar codes www.worthdata.com Owner s Manual Warning: This equipment generates, uses
More informationDISCLAIMER. advanced PANMOBIL Systems GmbH & Co. KG. All rights reserved. International support contact:
DISCLAIMER advanced PANMOBIL Systems GmbH & Co. KG (here after called PANMOBIL) reserves the right to make changes in specification and other information contained in this document without prior notice
More informationCode Reader 1000/1400/8000 Configuration Guide
Code Reader 1000/1400/8000 Configuration Guide Code Reader 1000 Code Reader 1400 Code Reader 8000 1 Table of Contents USB Settings USB Keyboard Mode...6 (A1) USB Downloader Mode...6 (A2) USB Virtual COM
More informationMini Wireless Barcode Reader Quick Guide
Mini Wireless Barcode Reader Quick Guide Full user s manual is available on the enclosed CD. Mini Wireless Barcode Reader Quick Guide P/N: 8002-0028*00 FCC WARNING STATEMENT This equipment has been tested
More informationPEDpro HANDS-FREE BLUETOOTH CONTROLLER. for Bluetooth 4 Tablets AND Computers Operating Manual
PEDpro HANDS-FREE BLUETOOTH CONTROLLER for Bluetooth 4 Tablets AND Computers Operating Manual 2 CONTENTS Before Turning on Your PEDpro... 4 Power... 5 Modes... 6 Changing the MODE... 7 Connecting and Pairing...
More informationZ3S. Quick Setup Guide V Connection Mode. Working via Bluetooth. Barcode Programming. Working via USB cable
Z3S V18.9.7 Quick Setup Guide Connection Mode Working via USB cable Get Started: Connect scanner with your device via USB cable. If you use US keyboard, it's a plug and play model. If you use other type
More informationGUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas). NOTICE
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas). NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device,
More informationData Capture for Workforce in Motion. D-Fly User Guide. Baracoda TM February 2010
D-Fly User Guide Baracoda TM February 2010 SUMMARY SUMMARY 2 REVISION HISTORY 3 INTRODUCTION 4 1. STYLUS 5 2. BATTERY 5 3. SWITCHING ON THE READER 5 4. QUICK START UP GUIDE 6 4.1. HOW TO READ BARCODES
More informationConfiguration Guide. Code Reader C005435_02_CR1000_CR8000_ConfigurationGuide 1
Code Reader 1000/8000 Configuration Guide Code Reader 1000 Code Reader 8000 C005435_02_CR1000_CR8000_ConfigurationGuide 1 Table of Contents USB Settings USB Keyboard Mode...6 (A1) USB Downloader Mode...6
More informationH-UC232S USB Serial Converter
H-UC232S USB Serial Converter FCC Warning This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
More informationWireless barcode scanner Manual Guide
2.4G_433M_Bluetooth 2.4G/433M/Bluetooth Wireless barcode scanner Manual Guide 32-bit high-speed CPU Super-long working time Simple setup Multi-language V1.00 1 Depth of Field Specification 2.4G_433M_Bluetooth
More informationSCANNING MADE SIMPLE. SERIAL PROGRAMMING COMMANDS manual
SCANNING MADE SIMPLE SERIAL PROGRAMMING COMMANDS manual Revision History Version Description Date V1.0.0 Initial release. September 27, 2016 V1.0.1 V1.0.2 Added the serial command for setting the Inter-Character
More informationWLP 4170 CCD Programming Guide
WLP 4170 CCD Programming Guide PROGRAMMING GUIDE Wasp WLP 4170 CCD Programming Guide Please Read Note: The Wasp WLP 4170 CCD Scanner is ready to scan the most popular bar codes out of the box. This manual
More information2.4GHz Wireless Optical Mouse
2.4GHz Wireless Optical Mouse Model #: MP1950BLK User Manual PID #: 111587-109342 Rev. 140402 All brand name and trademarks are the property of their respective companies Mac and Mac OS X are registered
More informationDM8000 Series Configuration Codes
DM8000 Series Configuration Codes 6/4/2010 Version 3.6 Legal Notices The software described in this document is furnished under license, and may be used or copied only in accordance with the terms of such
More informationUSB-A to Serial Cable
26-949 User s Guide 6-Foot (1.82m) USB-A to Serial Cable Please read this user s guide before using your new cable. 2/2 Package contents USB-A to Serial Cable User s Guide Driver CD Quick Start Features
More informationUSER S GUIDE. Screen Scroller Mouse. Making Your Mobile Life Easier. Making Your Mobile Life Easier.
Screen Scroller Mouse Making Your Mobile Life Easier. Visit our Web site at: www.targus.com Features and specifications are subject to change without notice. 2002 Targus Corp. 400-0088-001A USER S GUIDE
More information