s SINUMERIK 840D sl

Transcription

1 s SINUMERIK 840D sl ShpTurn 1.5 SP2 SINUMERIK 840D sl, CNC SOFTWARE 6-3 ) 6FC5842-1XG11-0YA0 with ShpTurn HMI, in 6 languages (EN,DE,FR,IT,SP,V-CH), n CF card; with license ) Exprt 6FC5842-1YG11-0YA0 SINUMERIK 840D sl, CNC SOFTWARE 31-5 ) 6FC5842-3XG11-0YA0 with ShpTurn HMI, in 6 languages (EN,DE,FR,IT,SP,V-CH), n CF card; with license ) Exprt 6FC5842-3YG11-0YA0 SINUMERIK 840D sl, CNC SOFTWARE 6-3/31-5 ) 6FC5842-3XC11-0YA8 with ShpTurn, in 6 languages (EN,DE,FR,IT,SP,V-CH), n DVD; withut license ) Exprt 6FC5842-3YC11-0YA8 Infrmatin abut installing and perating the sftware n SINUMERIK NCU 710.1, NCU 710.2, NCU 720.1, NCU 720.2, NCU 730.1, NCU The NCU sftware 1.5 SP2 (internal versin ) cnsists f the fllwing cmpnents: LinuxBase (NCU) V NCK Sftware V PLC OpSys V (PLC 317) PLC-FB15 V CP V MCP Client V SINAMICS Sftware V ShpTurn HMI-Embedded V Technlgy Cycles V Measuring Cycles V Cycles ISO Cmpatibility V Adapting Cycles V Installing the NCU sftware: Fr installing the NCU sftware yu will need the NCU service system V r higher n USB stick. New installatin can nly be perfrmed either using the NCU Service System and TCU with keybard r WinSCP. New installatins withut full keybard r WinSCP can nly be perfrmed using an USB stick which has been prepared fr autmatic upgrade (cf. General infrmatin). The sftware may nly be installed n a SanDisk CmpactFlash GB. MLFB / rder n. fr the empty card: 6FC5313-5AG00-0AA Installing the NCU service systems n USB stick: The NCU service system is lcated as a USB stick image in the emergency_btsys_ncu directry n the supplied DVD. The installdisk.exe cpy rutine is lcated in the same lcatin. Cnnect a 512MB r 1GB USB stick, recmmended type Siemens 6ES7648-0DCx0-0AA0, t yur prgrammer ("PG") r PC (with Windws XP) and nte dwn the letter f the drive t which the stick is cnnected. Run the installdisk rutine t cpy the NCU service system t the USB stick: installdisk --verbse --blcksize 1m <image file> <drive letter:> Example: ( -- means 2x minus sign) installdisk --verbse --blcksize 1m D:\ emergency_btsys_ncu\linuxbase-512m.img X: r Siemens AG 2008 I DT R&D 51 Page 1 f 33

2 ShpTurn 1.5 SP2 installdisk --verbse --blcksize 1m D:\ emergency_btsys_ncu\linuxbase-resize.img X: (When using the...resize.img, bt the NCU nce frm USB stick in rder t unpack the image n the stick). It is best t cpy the image in a DOS shell. T this end, yu will need administratr rights n yur PG/PC. After cmpletin f installdisk, remve the USB stick frm yur PG / PC and insert it again. Under Windws, yu will nw see an empty USB stick. Nw cpy the desired NCU sftware (file with ".tgz extensin) frm the supplied DVD, ncu_sw directry t yur USB stick. Yu may insert the USB stick int ne f the tw USB prts n the NCU 7x0. When the NCU is turned n, it will bt frm this USB stick. The peratin is always perfrmed via a TCU cnnected t the NCU, r via PG / PC using WinSCP with "Open Terminal". Fr a descriptin f the peratin f the NCU service system, please refer t the /IM7/ Dcumentatin n the supplied DVD. 1.2 Upgrading an NCU 7x0 with NCU sftware, versin 1.5 and higher With an upgrade, all user data n the CF card in the directries /user, /addn, /em, and the license key are maintained. Fr the upgrade f systems equipped with several NCUs / PCU50, please refer t Sectin 7 "Netwrking". Bt the NCU frm yur USB stick (see 1.1). Select the Service Shell using F2 / F3. Lg in with user name "manufact". This may require an external keybard, since user names must be written in lwer case letters. Enter the fllwing cmmand after the peratr prmpt $ in the service shell: sc restre -update /data/<ncu-sw>.tgz The sftware update is cmpleted when prmpt $ is displayed again. Remve the USB stick. Bt the NCU (Pwer ON / OFF). Nw yu can start up the PLC, drives and NC Upgrade using WinSCP Systems withut TCU at the NCU can be upgraded with WinSCP, fr example n a PCU 50. Fr this purpse, lg n at the NCU with WinSCP as "manufact" and cpy the required NCU sftware (file with extensin.tgz) frm the ncu_sw directry n the supplied DVD t /card/user/system/hme/manufact n the NCU. Then enter the fllwing cmmand under "Cmmands / Open Terminal": sc restre -update -frce <ncu-sw>.tgz The sftware is installed when the "Syncing disks... dne" message is displayed. Afterwards, the NCU must be rebted. The <ncu-sw>.tgz file n the NCU shuld be deleted. Nte: During the installatin, messages may be displayed claiming that the cmmunicatin partner has nt reacted fr sme time. Yu can ignre these messages, but please d nt cut the cnnectin in this case. 1.3 New installatin n CmpactFlash card r upgrade frm SW 1.3, SW 1.4 nt Sftware Versin 1.5 IMPORTANT: This prcedure cmpletely deletes anything existing n the CmpactFlash Card; this applies t an empty CmpactFlash Card as well. Bt the NCU frm yur USB stick (see 1.1). Select the Service Shell using F2 / F3. Lg in with user name "manufact"; when the CmpactFlash Card is empty; use "admin", passwrd "SUNRISE" instead. This may require an external keybard, since user names must be written in lwer case letters. Enter the fllwing cmmand after the peratr prmpt $ in the service shell: sc restre -full /data/<ncu-sw>.tgz The sftware update is cmpleted when prmpt $ is displayed again. Remve the USB stick. Bt the NCU (Pwer ON / OFF). When the system is started with TCU(s) fr the first time, the TCU(s) must be lgged n t the system. Siemens AG 2008 I DT R&D 51 Page 2 f 33

3 ShpTurn 1.5 SP2 Enter the TCU name (default TCUx) and the address f an assigned MCP. Nw yu can start up the PLC, drives and NC. 1.4 Systems withut TCU If, fr the sftware installatin crrespnding t 1.2 r 1.3 there is n OP with TCU available t perate the NCU- Service System, then peratr cntrl is als pssible frm the PCU50 r PC/PG using the WinSCP (Cmmands / Open Terminal) r VNC viewer. Under certain circumstances, it is nt pssible t install the sftware withut NCU Service System n the USB stick as there is nt enugh free memry space n the CF card. 1.5 Autmatic upgrade using a bt-capable USB stick: Using an apprpriately prepared USB stick >= 1GB, it is pssible t perfrm an autmatic restre update r restre full. T d this, a script (autexec.sh) and the NCU sftware must be cpied nt the stick. The name f the script must nt be changed. The NCU sftware cpied t the stick must be renamed as either update.tgz r full.tgz. The SIM/NCK rtary switch n the NCU must then be set t psitin 7 and the NCU bted frm the stick. The script nw nly runs when the rtary switch is in the 7 psitin. Otherwise, the system is bted frm the stick and a branch is made int the service menu. Frm the NCU sftware designatin, the script decides whether a restre update r a restre full is perfrmed. In additin, befre the restre peratin, the script backs up the data n the CF card. The prgress f the individual script steps can be tracked n the 7-segment display r als n the internal HMI. The precise significance f the displays and the individual steps are described in a separate dcument. The script is included n the DVD supplied. 2. New functins in NCK (r later) The machine manufacturer can set in machine data $MN_ASUP_EDITABLE whether the Siemens System ASUP frm _N_CST_DIR r a user ASUP frm _N_CUS_DIR (_N_CMA_DIR) shall be executed with RET r REPOS events. ET200S-F I/Os are supprted fr Safety Integrated. GETFREELOC can be called up several times during empty lcatin search in the tl management. The machine data $MA_JOG_AND_POS_MAX_JERK[axis] is nw active with NEWCONF. The cuplings TRAIL, LEAD and ELG are implemented fr (BCS) and (MCS). Fixed-pint apprach in JOG: Max. fur fixed pints can be defined via the machine data $MA_FIX_POINT_POS[]. The number f valid fixed pints is determined via the machine data $MA_NUM_FIX_POINT_POS. Apprach prcedure: - Select JOG mde - Activate via PLC interface (see 4.3) - Traverse axis using axis key (cntinuus resp. incremental) r handwheel until it stps autmatically. The axis stps at the defined fixed pint withut emitting an alarm message. The number f pssible parameterizable transfrmatins has been extended frm 10 t 20. Generic transfrmatin has been extended t include a 7th axis. The nesting depth f subprgrams and cntrl structures has been increased frm 8 t 16. The current axial setpint and actual braking path can be read using system variables. Basic crdinate system: $AA_DTBREB[AX] Ttal braking path $AA_DTBREB_CMD[AX] Path single interplatr $AA_DTBREB_CORR[AX] Overlaid mvements $AA_DTBREB_DEP[AX] Cupled axis Machine crdinate system: $AA_DTBREM[AX] $AA_DTBREM_CMD[AX] $AA_DTBREM_CORR[AX] $AA_DTBREM_DEP[AX] The number f safe cams (SN) has been increased t 30 with slutin line. Siemens AG 2008 I DT R&D 51 Page 3 f 33

4 ShpTurn 1.5 SP2 Empty lcatin search within turret magazines can be perfrmed using the same setting ptins as fr chain magazines. The prgram attribute ACTBLOCNO is used t utput the blck number frm the current blck cntaining the alarm upn alarm utput with active DISPLOF. Machine data $mc_ign_prg_state_asup defines whether the display f the ASUP name shall be suppressed. The ASUP is perfrmed silently. The functin Any Asup Active sets the new channel-specific VDI signal anyasupactive in DB.[channel].DBX The new channel-specific VDI signal silentasupactive is set in DB.[channel].DBX378 if an ASUP is perfrmed silently. Interruptability f ASUPs: Certain Prg-Events shall nt be prevented r stpped by VDI signal NC Stp DB[channel].DBX 7.3). This ensures that the Prg-Event is executed cmpletely independently f the VDI signal. The VDI signals NC Stp at the blck end DB[channel].DBX 7.2, NC Stp Axes plus spindle DB[channel].DBX 7.4 are discarded accrdingly. The functin is activated by the bit-cded machine data $MC_PROG_EVENT_IGN_STOP fr any Prg-Events. The subprgram return RET(...) allws yu t return t a blck number r label f the calling prgram. This functin has been extended such that yu can als specify any string as return target. Time mnitring n synchrnus spindles: When reaching setpint-side synchrnizatin, tw time windws are initialized which are used t mnitr the time span until actual value-side carse resp. fine synchrnizatin is reached. The size f the time windws is taken frm MD $MA_COUP_SYNC_DELAY_TIME[0/1]. Index 0 fr fine synchrnizatin and Index 1 fr carse synchrnizatin. The value f zer deactivates the respective mnitring mde. If actual value-side carse/fine synchrnizatin is nt reached befre the relevant time windw has expired, Alarm is utput. 3. General infrmatin: After the new installatin f NCU sftware 1.5 n a CmpactFlash card, a general reset f the NCU and PLC must be perfrmed: Turn the SIM / NCK switch t psitin 1, the PLC switch t psitin 3 and perfrm a POWER ON. NCU710 / NCU720: The PLC prgram must initiate an immediate (apprx. 20 secs) reactin t alarm "2120 NCK fan alarm" by stpping the axes in a cntrlled manner. NCU730: The PLC prgram must initiate an immediate (apprx. 20 secs) reactin t alarm "2120 NCK fan alarm" by stpping the axes in a cntrlled manner if n duble-fan mdule is used. NCU710 / NCU720: The NCU will nt pwer up if a fan mdule is nt installed r if the fan is defective. This applies fr NCU 730 with duble fan mdule nly in the case f failure f bth fans. Alarm "%1 data have been restred, f which %2 machine data, %3 errr" If %3 indicates that mre than zer errrs have ccurred, it is nt advisable t cntinue wrking with the data. T avid further prblems, yu shuld read in an up-t-date backup cpy f the data. It is nt always pssible t prt an NCK series startup file frm 840D pwerline withut prcessing t 840D sl. Prir t verwriting a licensed CF card, a backup f the license key is abslutely necessary The key is available in file keys.txt and is stred under the path card/keys/sinumerik The backup f the key can be carried ut, fr example, with WinSCP, by the PG / PC. Each license is assigned t a specific CmpactFlash card (card ID) and is nly valid n the assigned card. Mini handheld unit An additinal hardware is nw required t perate a mini handheld with handwheel. As previusly, the inputs are cnnected directly t the PLC I/Os r can alternatively be integrated int the input image f the MCP IE (X51 ) using a relevant cnnectin kit. Fr transmitting the handwheel signals, a machine cntrl panel (Ethernet r Prfibus) r a handwheel Prfibus cnnectin mdule is nw required as fr the type MPI handheld unit. Data backups shuld be read in in the rder NC, PL, drive. It will therefre make sense t create the NC, PLC and drive archives separately. Cntur handwheel and speed verride using a handwheel are nly release with Prfibus MCP. Siemens AG 2008 I DT R&D 51 Page 4 f 33

5 ShpTurn 1.5 SP2 The RESET buttn n the NCU can be used t restart the NCU mdule. It is nt ensured that this will als ensure a restart f the whle system in all cnfiguratins. This als applies fr the PI service f PLC with FB4. The catalg /siemens/system/etc. cntains a template fr the current standard basesys.ini. With intercnnected systems, we recmmend t assign names t the individual statins in the basesys.ini (e.g. hst name=ncu-2). If yu wish t intercnnect systems, the entry SyncMdeDHCPD_SysNet=ON_MASTER in the basesys.ini must be declared a cmment befre netwrking the DHCP master. Pwer-up sequence when starting up the system fr the first time after being intercnnected: DHCP master (s far DHCP server), then all ther statins. By default, Prt 102 n X130 is blcked. If yu wish t access the cntrller via X130 using STEP 7 r HMI, yu have t activate Prt 102. This can be achieved using the fllwing entry in the file /user/system/etc/basesys.ini: [LinuxBase] FirewallOpenPrts=TCP/102 If required, yu can als activate the Prt 5900 fr the VNC Viewer. The HT2 Ethernet handwheel is cnfigured at the fifth handwheel interface. Example fr three Ethernet handwheels. The third handwheel is lcated in HT2: MD11350[0]= [0]= [0]=1 MD11350[1]= [1]= [1]=2 MD11350[2]= [2]= [2]=5 HT2: The PLC applicatin example fr the HHU included with the Pwerline tlbx cannt be transferred t the HT2 withut several changes. The NCVAR variable descriptins must be adapted accrdingly. A revised example is prvided thrugh e_supprt r Tlbx. FC13 nw supprts the visualizatin f fur lines. As a result, the meaning f the ROW parameter has changed as fllws: 0 = N display utput 1 = 1st line 2 = 2nd line 3 = Line 1 and line 2 alternately 4 = 3rd line 5 = Line 1 and line 3 alternately 8 = 4th line F = Autmatic change f all lines The display cntents must be stred in the field ChrArray type string[64]. The upper fur keys are transferred t the PLC input image (the LEDs under these keys cannt yet be addressed). Sample parameter setting fr the HT2 at FB1 (OB100): BHG :=5 BHGIn :=DB100.BhgIn_170 BHGOut :=DB100.BhgOut_150 BHGStatSend :=DB100.DBD80 BHGStatRec :=DB100.DBD84 BHGInLen := BHGOutLen := BHGTimeut := BHGCycl := BHGRecGDN :=2 // crrespnds t the setting f the rtary switches * f the terminal bx resp. MPP. BHGRecGBZN :=2 // crrespnds t the setting f the rtary switches * f the terminal bx resp. MPP. BHGRecObjN :=1 BHGSendGDN :=2 BHGSendGBZN :=1 BHGSendObjN :=1 BHGMPI BHGStp BHGNtSend Siemens AG 2008 I DT R&D 51 Page 5 f 33

6 ShpTurn 1.5 SP2 * The rtary switches S1 and S2 at the terminal bx resp. MPP determine the DIP number used t register the nde in the system (here, S1=0, S2=2). Address 0 is nt permissible, as, with this setting, the DHCP Server cannt assign any addresses. HT2: The update rate f the display and the transfer f the handwheel signals (this imprves the velcity cntrl f the handwheel) can be imprved as fllws: Cpy the mcp_client file in the directry card\siemens\sinumerik\mcp_client\mcp_client.ini int the card\users\sinumerik\mcp_client directry and in the HT2 sectin, change the entry cyclemcpsend = 50. The cntrl must then be pwered dwn/pwered up. Alarm 46xx: The machine data fr the Ethernet handwheel must be checked. Example fr the first handwheel: MD11350[0]=7, 11351[0]=1, 11352[0]=1 Cmbinatins f NCUs with Sinamics Sxxx CUs have nt been released. Exceptins are nly permissible after prir cnsultatin. Spindle traversing with limited trque (Fcn) r spindle traversing t fixed stp: The perfrmance display at the HMI is calculated as 100% f the limited trque and utput. With NCK V r later and ADI4 bard V , the ADI4 bard can be perated n 840D sl with internal PLC 317. As befre, Dbsi 1 is nt released fr SINUMERIK with integrated drive cntrl. NCU Bis V1.4 (r later) is required t perate 1GB CmpactFlashCards in a NCU730. Upgrades are nly required infrequently s that the BIOS is nly available thrugh e_supprt. Just as befre, in cnjunctin with 840 D sl, the Starter is nly released fr diagnstic purpses. 4. Infrmatin abut the NCK: If the number f part prgrams set via machine data nearly crrespnds t the number f actually existing part prgrams, the value in the machine data must be increased (due t additinal cycles). The interplatry traversing f psitining axes is canceled with alarm Axis has nt IPO functinality. SPI and PW have (already always) been keywrds and cannt be used as axis identifiers. The G643 functin (blck-internal smthing) has been released fr applicatins in the tl change area (e.g. ptimizatins fr appraching the tl change psitin). The functin has nt been released fr applicatins in the machining prcess. The G644 functin (blck-internal smthing) has been released fr applicatins in the tl change area (e.g. ptimizatins fr appraching the tl change psitin). The functin has nt been released fr applicatins in the machining prcess. Sftware variant fr a max. f six axes: The default setting fr the number f axes is 3. The "Extended measurement" functin with distributed measuring input n the SINAMICS mdules is nt available (MEAC, MEASA, MEAWA). Gaps in the channel sequence are nt permitted in systems with a maximum f tw channels. Access t drive data via $nn_nn system variables is nt enabled. The nly available system variables are thse transferred in telegram 116. Extended stp and retract (ESR) has nt been enabled. ASUBs can nw be started alng the line f the 840Di functinality via the Prfibus PLC I/Os. Machine data settings must be selected by the same methd used n the 840Di system. There are n high-speed NCK I/Os mapped in DB10 f the PLC. Hwever, the ASUB start ptins used in earlier versins (i.e. frm DB10 r FC9 via PLC prgram) are still available. High-speed ET200 Simatic mdules can be used as a replacement fr the DMP mdules used n Pwerline. Fr this, yu can perate ne f the tw Prfibus lines in synchrnism with the clck with PLC317 in cmbinatin with NCK V r later (mre details are prvided in a separate descriptin). With a 31-axis sftware n an NCU 710.1, yu can use six ut f 31 axes and fur ut f ten channels. Machine data $MN_MAXNUM_PLC_CTRL_AXES is n lnger included in the data recrd. It has been replaced by MD MD $mn_psctrl_cycle_delay must be zer. Check the available data backup. Machine data $ma_rated_utval[ ] must have value zer. IMD (integrated mnitring & diagnstic) : Siemens AG 2008 I DT R&D 51 Page 6 f 33

7 ShpTurn 1.5 SP2 Feedback in GUD variable _PM_MISSING_TOOL_REFRESH after writing the variables t "1" is updated nly after image change. Safety: There is a new ptin handling referring t synchrnized actins r synchrnized actin elements. Up t versin 1.3 (NCK 62), synchrnized actin level 2 was set autmatically at the same time with ptin SI. Thus, channel MD 28250, NUM_SYNC_ELEMENTS culd be set t a value > 159. This has been changed with NCK versin 67. Synchrnized actin level 2 is n lnger included in Safety. Instead there is a new machine data, in which the synchrnized actin elements fr SAFE.SPF are defined, i.e. MD 28251, NUM_SAFE_SYNC_ELEMENTS. This machine data can be written with max. value 500 fr ptin SLP_I_O=1, and with a max. value f 5000 fr ptin SPL_I_O=2. Hwever, the number f synchrnized actin elements required shuld be determined in rder t prevent the perfrmance frm being laded unnecessarily. With system variable $AC_SAFE_SYNAC_MEM, the relevant number f free SI synchrnized actin elements can be read. If this variable is called prir t starting and after running SAFE.SPF, the difference is the number f elements ccupied by SAFE.SPF. This difference adding a certain reserve shuld be entered in MD Index 1-5 must be indicated when writing MD via synchrnized actins. Safety: Changed check sums f Safety integrated int the drive. The check sum fr these functins must be cnfirmed again due t new drive-integrated safety functins. T this end, enter 95 (safety start-up) in parameter p10. Subsequently, cpy the parameters f the current check sum t the parameters f the target check sum. p9798 t p9799 p9898 t p9899 Subsequently, p10 must be set t zer again. This will autmatically save the values (p971=1 is set). Wait fr the prcess f saving t be cmpleted. The prcesses mentined abve can als be triggered in HMI Advanced under IBN/NC/Safety Integrated using the sftkeys "Activate start-up mde" and "Deactivate start-up mde". With Sftware Versin 1.5 HF2 / 2.4 SP1 r later, the HT2 can be used as handheld unit. The auxiliary functin M6 is n lnger utput as standard after blck search. Remedy: Change the auxiliary functin grup in MD $mc_auxfu_predef_grup[5] int an unassigned grup. If the value f MD18210 deviates frm the default, MD18210 must be increased by min. 21 MB DRAM t upgrade the system frm SW1.4 / 2.4 t SW1.5 HF4 / 2.5 HF 1. Tl Manager: There is a new handling ptin. If several real magazines are used, these must be enabled using the ptin. One real magazine is included in the basic scpe. Fr cmpatibility reasns, the previus ptin bit $ON_TECHNO_FUNCTION_MASK Bit4=1 must still remain set. This is, hwever, nt included in the license handling. With SMI encder, the functin parking axis cannt be activated withut vltage Off/On. The functin fixed-pint apprach G75 is nt permissible with active radius crrectin G41 / G42 (Alarm Index 9). With fixed-pint apprach with G75, the fixed pint is nw apprached with nn-linear interplatin (RTLIOF). As a cnsequence, the axes are traversed with the jerk set fr psitining axes ($MA_JOG_AND_POS_MAX_JERK). The machine data 11295[0..9] is nw memry-cnfiguring. An alarm is nt utput in case f change. In existing archives, all values deviating frm the standard must be remved befre perfrming the upgrade. If yu wish t use the service interface X127 with PG/PC n a NCU7x0.2 with SW 2.6, yu have t ensure that the PG/PC netwrk interface is perated in "DHCP Client" mde, that means "Autmatically btain IP address ". After setting the PG/PC netwrk interface f a fixed IP ( xx), a ping is sent t X127, but yu cannt g nline neither with STEP 7 nr using a SINUMERIK Operate. The firewall is activated by default. The maximum CU r NX drive system lad may nt exceed 80% (lad displayed in parameter 9976[xx]). In the Reset state, the NCU lad exerted by psitin cntrller and interplatr may nt exceed 50%. The current lad can be checked under Diagnsis / System resurces. Siemens AG 2008 I DT R&D 51 Page 7 f 33

8 ShpTurn 1.5 SP2 Enhanced functins and further develpments: RQ ID AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP AP Infrmatin abut the PLC: Tlbx, V r higher, and Step 7, versin 5.4 SP2 r higher, are required. The current cycle time is n lnger available in DB5, but in DB8 instead. The cycle time can als be called via the start infrmatin f OB1. The PLC mdule IM153-2 MLFB 6ES AA02-0XB0 cannt be used. Remedy: 6ES AA03-0XB0 The PLC series startup file must be generated when the PLC is stpped. It cannt therwise be guaranteed that the PLC will switch t cyclic peratin when the data backup has been laded. Sinamics parameters are required fr star / delta switchver with FC17. Prerequisites: The relevant DDS/MDS must be set up in the drive. P827[0] P827[1] P827[n] must be set t different values. The cntactr is switched ver by the applicatin => P833, Bit0=1 The pulses are disabled by the drive => P833, Bit1=0 Initial PLC psitin: Star mde, therefre set bit 21.5 in the axis DB t 1 during pwer-up. The X127 service interface n the NCU is t be used exclusively fr start-up and service. The machine cntrl panel (MCP) is perated n Prfibus r Ethernet. N mixed peratin! Prfibus 1 must be cnfigured s that the CU, supply and drive sftkeys are displayed at the HMI. The blcks FC1007 AG_LOCK, FC1008 AG_UNLOCK, FC1010 AG_CNTRL have nt been released. The PLC FORCEN [FORCING] functin in cnjunctin with 840D sl has nly been released with sme restrictins. It is pssible with the PLC317 frm the PLC perating system >= V (2.4 SP1 HF11) / PLC319 and higher, PLC perating system >= V (2.4 SP1 HF11) and higher. With 840D sl, it is nt permissible t cnnect the VDI interface signal DB10.DBX Infrmatin abut the SINAMICS drive: The Starter may nt be used in cmbinatin with Sinumerik V1.5 / V2.5. N parallel use f measuring functins fr i and n measurements via starter and HMI Advanced. Starter measurements require a Pwer OFF => ON and immediate measurement with the starter. Starter measurements must nt be perfrmed after HMI Advanced measurements. If a SINAMICS cmpnent is replaced and the sftware upgraded, the firmware release must be checked and, where necessary, the riginal firmware release restred. (Key wrd: macr ) Firmware releases can be checked in the fllwing parameters: Cntrl unit R18 Firmware release f CU Supply R128 Firmware release f infeed Siemens AG 2008 I DT R&D 51 Page 8 f 33

9 ShpTurn 1.5 SP2 Drive MD R128 Firmware release f pwer unit R148 Firmware release f sensr mdule V1.4 / V2.4: Fr the time being, the starter is still required fr determining the mtr cdes. Mains vltages: Fr smth peratin in the target cuntry the fllwing parameters must be set in the specified rder: P010 = 1 P210 = rated mains vltage in the target cuntry P211 = rated mains frequency in the target cuntry P340 = 1 P3410 = 4 P3900 = 3 Save RAM t ROM Pwer OFF the system; pwer it ON again n the target netwrk nly. With the next ON cmmand at ALM a netwrk identificatin is run and the determined values are saved prtected against pwer failure. The APC functin increases the NCU lad. Prir t using this functin a perfrmance estimate must be carried ut. p1240, p1244, p1248, p1250: If Vdc cntrl and DDS switchver have been activated in V2.4, check if crrect values have been entered in the cntents f indexes >0 f p1240 after upgrading the system. DMC20/HUB has nt been released. With 840D sl and SW 1.5 SP1, 62.5 µs drive cycles have been released. The fllwing cnditins apply accrdingly: - with this setting, tw axes can be perated n ne CU r NX. - nly the same clck cycles can be set n a duble-axis mdule. Temperature prewarning messages (DB[axis].DBX94.0, DBX94.1) spradically ccur. Remedy: Only evaluate the signal in the PLC if this is pending in the VDI interface fr mre than 1.5 s. Fr SINUMERIK sftware releases 1.3 and 1.4/2.4, different firmware versins f the cmpnents (NCU, NX, Mtr Mdules, DRIVE-CLiQ mtrs) invlved in the safety functins can be cmbined (mixed) withut having t adapt the firmware versins. The fllwing applies frm SINUMERIK sftware release 1.5/2.5 and higher: The firmware versins f the Mtr Mdules, Sensr Mdules and DRIVE-CLiQ mtrs (include integrated Sensr Mdules) invlved in the safety functins must be adapted t the SINAMICS firmware versin f the NCU. This ccurs autmatically when bting, if parameter p9826 (firmware, autmatic) is set t 1 (standard setting). When using Safety Integrated, parameter p9826 (firmware, autmatic) must be set t 1 and must nt be re-parameterized. Fr the acceptance test f Safety Integrated, the safety firmware versins f all f the Mtr Mdules, Sensr Mdules and DRIVE-CLiQ mtrs - invlved in the safety functins - must be read-ut, lgged and checked against the fllwing list: Each line in the tables represents a pssible cmbinatin f safety firmware versins. When bting, chassis units must be perated in the pen-lp cntrl mde (refer t MD35020). Machine data change as a result f a changed Drive ES SlaveOM The Drive ES SlaveOM is respnsible fr allcating addresses f drive units cnnected t Prfibus f the PLC. The addresses are allcated in the PLC HW Cnfig. The addresses allcated here must be entered int the NC machine data MD13050[nn] crrespnding t the required axis cnfiguratin. When a Starter V4.1.n (r later) is installed (later, including the the installatin f tlbx V2.6), the new Drive ES SlaveOM is linked in. Cntrary t the previus situatin, nw, an address space fr 6 axes is reserved fr each CU r NX. This is realized when creating a PLC hardware cnfiguratin fr the first time. As a result, addresses may be shifted r gaps ccur. This mdified address allcatin must then be cmmunicated t the NC in machine data 13050[nn], as therwise the allcatins will n lnger be crrect. This is especially true if existing NC data back-ups (archives) are being used as therwise these will n lnger match the PLC hardware cnfiguratin. Siemens AG 2008 I DT R&D 51 Page 9 f 33

10 ShpTurn 1.5 SP2 Further, in HW Cnfig, the address f telegram 390 (PZD-2/2) f the first NX changes frm 6516 t When using additinal NX mdules, the address is incremented with an ffset f 10. Machine data MD13120[1+n] must be crrespndingly adapted. If existing PLC prjects are imprted int an S7 envirnment with new Drive ES SlaveOM, then the ld (previus) address cnfiguratins are kept. Hwever, the drive bjects that have been newly inserted int this prject receive the new address allcatin. A Standard (new) address allcatin is achieved using Rerganize addresses. If, fr NX bjects, the Standard telegram 1 (PZD-2/2) is entered frm an existing cnfiguratin, then this must be replaced by telegram 390 in rder t achieve a standard, new address allcatin. Example: One NCU with a Sinamics Integrated and tw NX10 each with 3 axes are cnfigured. Address allcatin with the Drive ES SlaveOM versin ld : On NX10_1, the 3 rd axis has the address 4420 On NX10_2, the 1 st axis has the address 4460 Address allcatin with the Drive ES SlaveOM new On NX10_1, the 3 rd axis has the address 4420 On NX10_2, the 1 st axis has the address 4580 Versin f Drive ES SlaveOM ld Siemens AG 2008 I DT R&D 51 Page 10 f 33

11 ShpTurn 1.5 SP2 PLC HW cnfiguratin Siemens AG 2008 I DT R&D 51 Page 11 f 33

12 ShpTurn 1.5 SP2 NX10_1 Siemens AG 2008 I DT R&D 51 Page 12 f 33

13 ShpTurn 1.5 SP2 NX10_2 Siemens AG 2008 I DT R&D 51 Page 13 f 33

14 ShpTurn 1.5 SP2 Versin f Drive ES SlaveOM new Siemens AG 2008 I DT R&D 51 Page 14 f 33

15 ShpTurn 1.5 SP2 NX10_1 Siemens AG 2008 I DT R&D 51 Page 15 f 33

16 ShpTurn 1.5 SP2 NX10_2 Siemens AG 2008 I DT R&D 51 Page 16 f 33

17 ShpTurn 1.5 SP2 Machine data13050[nn] Siemens AG 2008 I DT R&D 51 Page 17 f 33

18 ShpTurn 1.5 SP2 Re-rganizing addresses 7. Infrmatin abut HMI Embedded: The HMI Embedded sftware V07.50.xx is started autmatically as a cmpnent f the NCU sftware 1.5 in the pwer-up f the NCU7x0. HMI Embedded is als referred t as an "internal HMI". HMI Embedded can nly be perated via a cntrl panel with TCU cnnected via Ethernet t X120 n the NCU7x0. The cnfiguring data, such as PLC message and alarm texts and HMI ptin package ("Wizard"), must be stred n the CmpactFlash card in the NCU in the apprpriate directries under /card/user/sinumerik/hmi/... r /card/em/sinumerik/hmi/... (see dcumentatin IM2, BE1). The file system n the CmpactFlash card can be accessed in "nline" mde nly, i.e. when the NCU is running. The data can be transferred either by means f a USB stick r netwrk link via the HMI peratr interface (startup / HMI area) r by means f a netwrk link and the WinSCP tl. IMPORTANT: File names f cnfiguring files must nrmally be written in lwer case letters. Display MD 9990 SW_OPTIONS has n significance. All HMI ptins must be activated thrugh license management. The ptin "Additinal 256MB HMI user memry n the CmpactFlash card" is required t be able t stre part prgrams and archives n the CmpactFlash card ("lcal drive"). NOTICE: An NCK general reset deletes the ptin and renders the "lcal drive" inaccessible until the ptin is set again. Existing data stred n the card are nt affected. If yu are perating an NCU withut TCU (i.e. with HMI Advanced n PCU 50), it is advisable t deactivate HMI Embedded. Yu can d this by executing cmmand "sc disable hmi" in the service shell. Siemens AG 2008 I DT R&D 51 Page 18 f 33

19 ShpTurn 1.5 SP2 OP keybards can be switched between upper case and lwer case letters by simultaneusly pressing Shift+Ctrl. T be able t use the characters represented when pressing Shift (e.g. Shift A => [ ), capitalizatin must be active Limitatins in HMI Embedded: Muse peratin is nt supprted, peratin via tuch panel (als nt with HT8) is nt permissible. Cpying a file t CF card by verwriting an existing file with the same name will cause an "internal errr" message. The file with the same name must be deleted befre. Display MD 9210 USER_CLASS_WRITE_ZOA is nt active fr "active wrk ffset" in the Parameter area. Display MD 9900 MD_TEXT_SWITCH des nt have any effect. All cnfigured netwrk drives (access t server via Ethernet) must be permanently accessible during the runtime f HMI Embedded. Fr the cmmissining f the SINAMICS drives, an external HMI Advanced, sftware versin 7.5 r higher, r cmmissining tl 7.5 is required (the CD SINUCOM includes the cmmissining tl). Prcessing frm external surces / EXTCALL is nly permissible with single-channel machines. Ladable cmpile cycles cannt be backed up r read in using NC series startup archive. Ladable cmpile cycles are stred n the CF card f the NCU and retained in case f NC memry reset. They can be handled like HMI cnfiguring data. In a part prgram with EXTCALL calls, there must be at least ne ther NC blck between tw sequential EXTCALL calls with a prcessing duratin f at least ne secnd. When very big files are saved n CF card, the message "Please wait File being flashed" is displayed. This message must be acknwledged by pressing the Recall buttn. If yu want t switch ff the cntrl after having saved the file, yu will have t wait fr ne secnd fr each MB file size. After reading in a NC series startup archive, an explicit restart f the HMI is required, e.g. thrugh NCK reset r peratin with CTRL + Q, Enter. It is nt pssible t integrate a user bt screen. 7.2 Imprved functinality with respect t SW 1.5 SP1 HF2 AP AP The ShpMill interface may freeze in the editr The HMI might crash under certain circumstances in the G cde editr 8. Infrmatin abut the NCU Base sftware: The Linux perating system f the NCU7x0 is als referred t as the NCU Base sftware, similar t the PCU Base sftware fr the PCU 50. Yu will find the relevant dcumentatin in IM7 n the DVD-ROM. The NCU base sftware ensures the start amng ther things f the NC, PLC, and HMI sftware during pwer-up, as well as the bting f the TCU if it is present. The NCU Base sftware is user-riented, i.e. yu must lg in and enter a passwrd in rder t acquire specific access authrizatin. This current lgin and passwrd prtectin is nly relevant fr accessing a Linux service shell r the CmpactFlash card using WinSCP. Fr startup and servicing activities, the lgin ID is "manufact" and the passwrd "SUNRISE" (case-sensitive!). T pen the Linux service shell n the TCU, press keys "Area switchver" and "Recall" (F10 and F9) simultaneusly, then "Scan fr Servers", "2" r bt frm the USB service system. Fr access via the netwrk using WinSCP, enter the abvementined lgin and passwrd n the "Sessin" screen. This lgin prcedure als applies after the NCU7x0 has bted frm a USB stick with the NCU service system prvided that executable NCU sftware is installed n the CmpactFlash card. If this is nt the case (e.g. if the CmpactFlash card is empty), enter the lgin ID "admin" and passwrd "SUNRISE". Yu can display a list f the syntax f all available service cmmands in the service shell by running cmmand "sc help". Siemens AG 2008 I DT R&D 51 Page 19 f 33

20 ShpTurn 1.5 SP Netwrking: Please bserve the current dcumentatin "Operatr Cmpnents and Netwrking (IM5) Versin 04/2008"! Imprtant system and netwrk settings fr the NCU base sftware have been preset in the file basesys.ini in the directry /card/user/system/etc and may be mdified there. The riginal basesys.ini file is lcated at /card/siemens/system/etc, it is entitled "template-basesys.ini". Each NCU within the plant / system netwrk shuld be assigned a unique ("talking") cmputer name, tgether with the entry "Hst name=..." in basesys.ini. Permissible characters are uppercases / lwercases, numbers and minus signs. The NCU DHCP server shuld always be switched n. When upgrading the system frm SW 1.3 / 1.4 please ensure that n ld mcp_client.ini file remains in /card/user/sinumerik/mcp_client Cnfiguring 1 NCU with TCUs and MCPs In this cnfiguratin, n special settings must be made in the basesys.ini. The DHCP server and internal HMI-Embedded remain activated Cnfiguring 1 NCU with 1 PCU 50, MCPs and TCUs, if required In this cnfiguratin, make the fllwing settings in the basesys.ini f the NCU: Hst name =... SyncMdeDHCPD_SysNet = ON_MASTER In general, the internal HMI-Embedded must be deactivated because tw HMIs (HMI-Advanced and HMI-Embedded/JbShp) may nly be perated n ne NCU in particular cases. On PCU 50, we recmmend that yu use PCU base sftware V8.1 SP3 r later. In the System Netwrk Center, tab TCU Supprt, select the default cnfiguratin "N bt supprt". If the system is equipped with a TCU (HT8) that shall be switched t PCU 50 by default, the fllwing entries must be made in the file /card/user/cmmn/tcu/<tcu Name>/cmmn/tcu/cnfig.ini n the NCU MaxHstIndex = 1 [hst_1] Address = <IP address f the PCU> Cnfiguring several NCUs and, if necessary, 1 r several PCUs, TCUs, MCPs In this cnfiguratin, make the fllwing settings in the basesys.ini f the NCU: Unique hst name =... fr each NCU Unique InternalIP=... Unique InternalNetMask=... Exactly ne NCU with SyncMdeDHCPD_SysNet = ON_MASTER On PCU 50, yu have t use PCU base sftware V8.1 SP3 r later. In the System Netwrk Center, tab TCU Supprt, leave the default cnfiguratin "Cmplete TCUsupprt" unchanged. Under the tab DHCP Settings, we recmmend t set "Sync mde lw pririty". All peratr statins within the plant / system netwrk (TCUs, HT8, PCU 50) are managed n the NCU with "ON_MASTER", that means the cnfig.ini files as well as the.leases file cmprising all IP addresses assigned within the system which are relevant during the runtime are stred there. The cnfig.ini files are distributed t all ther NCUs / PCUs by the master NCU using the service cmmand "sc distribute tcudata". Via the Service cmmand "sc clear dhcp" and subsequent pwer ON / OFF f the cmplete system, the NCUs / PCUs are assigned preset IP addresses. New addresses are assigned t TCUs and MCPs and the.leases file is then distributed t all ther NCUs / PCUs. Imprtant: The System Netwrk Center, tab OPs allws t directly edit n each PCU 50 the cnfig.ini files f all peratr statins n the master NCU. The data are autmatically distributed t all NCUs / PCUs each time they are changed. 9. Infrmatin abut technlgy cycles: NCU sftware 1.5 SP1 includes the technlgy cycles (standard cycles) in an installable frm. Siemens AG 2008 I DT R&D 51 Page 20 f 33

21 ShpTurn 1.5 SP2 Installing the technlgy cycles: Step 1 - Reading in the archives Read in the necessary archive files: cyccust_gr.arc cyccust_uk.arc cycles.arc cycmill.arc cycturn.arc defines.arc ;*Archive fr user cycles German ;*Archive fr user cycles English ;*Archive with all standard cycles (milling and turning cycles) ;*Archive with all milling cycles ;*Archive with all milling cycles ;*Archive with definitin files In the "Services" area, select the "Prgram data" sftkey and navigate t "Cycle archive" using the cursr keys; t pen, use the Input key. In the "Cycle archive" area, navigate t "Standard cycles" using the cursr keys; t pen, use the Input key. Read in the necessary archive files by selecting the vertical sftkey "Read in archive". Nte: The archive files must be selected and read in separately. Once all the relevant archive files have been read in, yu must perfrm an NCK reset by selecting sftkey "NCK Reset" in the "Startup" area. Step 2 - Activating the definitin files In the "Prgram" area, select the ETC key ">" t g t the 3rd level. On this level, select the "Definitin files" sftkey, select the definitins separately and activate them using the "Activate" sftkey. Step 3 - Activating the "Swivel cycle" sftkey in the "Start-up" area In the "Prgram" area / "Standard cycles", edit the "cmmn.cm" file and delete the semicln in the beginning f the line ;SC616 = STARTUP.COM Then select the "NCK Reset" sftkey in the ">>Startup" area. Step 4 Activating the "Thread recutting" sftkey in the "Machine" area "Jg" In the "Prgram" area / "Standard cycles", edit the "cmmn.cm" file and delete the semicln in the beginning f the line ;SC108 = MA_JOG.COM Then select the "NCK Reset" sftkey in the ">>Startup" area. 10. Infrmatin abut measuring cycles: NCU sftware 1.5 SP1 includes the measuring cycles in an installable frm. Installing the measuring cycles: Step 1 - Machine data settings The machine data listed belw apply fr the use f Siemens standard and measuring cycles: (1) Machine data (memry-cnfiguring) fr Glbal User Data (GUDs): MD 18130: MM_NUM_GUD_NAMES_CHAN=130 (2) Machine data (memry-cnfiguring) fr number f cycles and number f transfer parameters MD 18180: MM_NUM_MAX_FUNC_PARAM=800 (3) Further machine data fr measuring cycles MD 11420: LEN_PROTOCOL_FILE=5 (maximum file size fr prtcl file, set in KB) MD 28082: MM_SYSTEM_FRAME_MASK Bit0 und Bit5 =1 (system frames fr scratching and cycles) Step 2 - Reading in the archives Read in the necessary archive files: Siemens AG 2008 I DT R&D 51 Page 21 f 33

22 ShpTurn 1.5 SP2 cyccust_gr.arc ;*Archive fr user cycles German cyccust_uk.arc ;*Archive fr user cycles English mcycles.arc ;*Archive with all measuring cycles (milling and turning) mcycmill.arc ;*Archive with all measuring cycles fr milling mcycturn.arc ;*Archive with all measuring cycles fr turning defines.arc ;*Archive with definitin files (GUD5.DEF, GUD6.DEF, GUD7_MC.DEF) jgmcyc.arc ;*Archive with all measuring cycles fr measuring in JOG In the "Services" area, select the "Prgram data" sftkey and navigate t "Cycle archive" using the cursr keys; t pen, use the Input key. In the "Cycle archive" area, navigate t "Measuring cycles" using the cursr keys; t pen, use the Input key. Read in the necessary archive files by selecting the 1st vertical sftkey "Read in archive". Nte: The archive files must be selected and read in separately. Once all the relevant archive files have been read in, yu must perfrm an NCK reset by selecting sftkey "NCK Reset" in the "Startup" area. Step 3 - Activating the definitin files In the "Prgram" area, select the ETC key ">" t g t the 3rd level. On this level, select the "Definitin files" sftkey, select the definitins GUD5.DEF, GUD6.DEF and GUD7.DEF separately and activate them using the "Activate" sftkey. Step 4 - Activating the access sftkeys "Measurement turning" and "Measurement milling" fr supprt In the "Prgram" area / "Standard cycles", edit the "cmmn.cm" file and delete the semicln in the beginning f the line ;SC326 = AEDITOR.COM ;* "Measurement turning" sftkey ;SC327 = AEDITOR.COM ;* "Measurement milling" sftkey Then select the "NCK Reset" sftkey in the ">>Startup" area. Step 5 - Activating the "Measuring cycles" sftkey in the "Start-up" area In the "Prgram" area / "Standard cycles", edit the "cmmn.cm" file and delete the semicln in the beginning f the line ;SC617 = STARTUP.COM Then select the "NCK Reset" sftkey in the ">>Startup" area. 11. Ntes n the cycles (ISO cycles) fr the "Online ISO Dialect Interpreter": NCU sftware 1.5 includes the ISO cycles V in an installable frm. Installing the ISO cycles: Installatin f the ISO cycles requires previus cmmissining f the standard cycles. Befre yu begin the startup prcess, yu shuld ensure that the existing status is saved t an archive; read ut a series startup archive if necessary. Dcumentatin: ISO dialects fr SINUMERIK 6FC5297-6AE10-0APx Prgramming Manual ISO Milling 6FC5298-6AC20-0BPx Prgramming Manual ISO Turning 6FC5298-6CA00-0BGx Step 1 - Machine data settings: Yu can activate the Online ISO Dialect Interpreter using the machine data $MN_EXTERN_LANGUAGE. The language types ISO dialect M (Milling) r T (Turning) can be selected via machine data $MN_EXTERN_CNC_SYSTEM. Step 2 - Reading in the archives ismill.arc ;*Archive with all ISO cycles fr milling isturn.arc ;*Archive with all ISO cycles fr turning defines.arc ;*Archive with definitin file (GUD7_ISO.DEF) Fr the prcedure fr reading in the archive files, please refer t: "Infrmatin abut the technlgy cycles" Siemens AG 2008 I DT R&D 51 Page 22 f 33

23 ShpTurn 1.5 SP2 An verview f the path structure n the CmpactFlash card in which the files fr the ISO cycles are stred can be fund belw. siemens/ sinumerik/ cycles/ archives isc/ hlps/ lngs/ prg/ defines.arc ismill.arc isturn.arc versins.xml prg.cfs prj/ startstp.sh versins.xml prj.cfs versins.xml ;Help files ;Language files ;Includes archives fr the ISO cycles ;Includes GUD7_ISO.DEF ;Includes the ISO cycles fr milling ;Includes the ISO cycles fr turning ;The XML file cntains the versin number f the ISO cycle archives ;Zipped prg/ flder ;Cnfiguratin ;Script file fr linking the subflders ;The XML file cntains the versin number ;Zipped prj/ flder ;Includes the versin numbers f the ISO cycles and Step 3 - Activating the definitin files Activate the GUD7.DEF definitin file. Fr the prcedure fr activating the definitins, please refer t: "Infrmatin abut the technlgy cycles" Siemens AG 2008 I DT R&D 51 Page 23 f 33

24 ShpTurn 1.5 SP2 List f G cdes with the crrespnding envelpe cycles and technlgy cycles: Milling: G Cde Envelpe Cycle Siemens Technlgy Cycles G05 CYCLE305 G08 CYCLE308 G10.6 CYCLE3106 G22 CYCLE322 G23 CYCLE323 G27 CYCLE328 G28 CYCLE328 G30 CYCLE330 CYCLE396 G71.1 / 72.2 CYCLE3721 G81 CYCLE381M CYCLE82 G82 CYCLE381M CYCLE82 G85 CYCLE381M CYCLE85 G86 CYCLE381M CYCLE88 G89 CYCLE381M CYCLE85 G83 CYCLE383M CYCLE83 G73 CYCLE383M CYCLE83 G84 CYCLE384M CYCLE3841 G74 CYCLE384M CYCLE3841 G76 CYCLE387M CYCLE86 G87 CYCLE387M CYCLE861 Turning: G Cdes A/B/C Envelpe Cycle Siemens Technlgy Cycles G05 CYCLE305 G10.6 CYCLE3106 G22 CYCLE322 G23 CYCLE323 G27 CYCLE328 G28 CYCLE328 G30 CYCLE330 CYCLE396 G50.2 / 51.2 CYCLE3512 G70 / 70 / 72 CYCLE370T G71 / 71 / 73 CYCLE371T CYCLE395 G90 / 77 / 20 CYCLE371T G72 / 72 / 74 CYCLE372T CYCLE395 G94 / 79 / 24 CYCLE372T G73 / 73 / 75 CYCLE373T G74 / 74 / 76 CYCLE374T CYCLE375T G75 / 75 / 77 CYCLE374T CYCLE375T G76 / 76 / 78 CYCLE376T CYCLE398 G92 / 78 / 21 CYCLE376T CYCLE398 G83 CYCLE383T CYCLE375T G87 CYCLE383T CYCLE375T G84 CYCLE384T CYCLE84 G88 CYCLE384T CYCLE84 G85 CYCLE385T CYCLE375T G89 CYCLE385T CYCLE375T Siemens AG 2008 I DT R&D 51 Page 24 f 33

25 ShpTurn 1.5 SP2 12. Infrmatin abut ShpTurn: General infrmatin: Upgrade in the metric unit system nly! The Wrk step prgramming ptin is required t create ShpTurn prgrams. The tl type "Limit stp" has been assigned number 730. Number 750 was used fr the "Limit stp" tl in ShpTurn befre. The change represents an adaptatin t HMI Advanced. Machine data fr ShpTurn: An verview is prvided under the Tls zer perating area => Extended sftkey bar => Machine data sftkey. N10134 $MN_MM_NUM_MMC_UNITS=6 ;minimum N10260 $MN_CONVERT_SCALING_SYSTEM=1 N10602 $MN_FRAME_GEOAX_CHANGE_MODE=1 N10610 $MN_MIRROR_REF_AX=0 N10700 $MN_PREPROCESSING_LEVEL='H25' : bit0=1, bit2=1, bit5=1 N10702 $MN_IGNORE_SINGLEBLOCK_MASK='H10' : bit4=1 N10714 $MN_M_NO_FCT_EOP=32 ;variable N10722 $MN_AXCHANGE_MASK='H4' : bit2=1 N10735 $MN_JOG_MODE_MASK='H1' : bit0=1 N11270 $MN_DEFAULT_VALUES_MEM_MASK='H1' : bit0=1 N11346 $MN_HANDWH_TRUE_DISTANCE=2 ;variable N11410 $MN_SUPPRESS_ALARM_MASK='H1007' : bit0=1, bit1=1, bit2=1, bit12=1 N11415 $MN_SUPPRESS_ALARM_MASK_2='H20' : bit5=1 N11450 $MN_SEARCH_RUN_MODE='H7' : bit0=1, bit1=1, bit2=1 N11470 $MN_REPOS_MODE_MASK='H8' : bit3=1 N11604 $MN_ASUP_START_PRIO_LEVEL=1 ;minimum N17530 $MN_TOOL_DATA_CHANGE_COUNTER='HF' : bit0=1, bit1=1, bit2=1, bit3=1 N18080 $MN_MM_TOOL_MANAGEMENT_MASK='HB' : bit0=1, bit1=1, bit3=1 N18118 $MN_MM_NUM_GUD_MODULES=7 ;minimum N18120 $MN_MM_NUM_GUD_NAMES_NCK=20 ;minimum N18130 $MN_MM_NUM_GUD_NAMES_CHAN=300 ;minimum N18150 $MN_MM_GUD_VALUES_MEM=120 ;minimum N18160 $MN_MM_NUM_USER_MACROS=30 ;minimum N18170 $MN_MM_NUM_MAX_FUNC_NAMES=200 ;minimum N18180 $MN_MM_NUM_MAX_FUNC_PARAM=3000 ;minimum N18280 $MN_MM_NUM_FILES_PER_DIR=400 ;minimum N18320 $MN_MM_NUM_FILES_IN_FILESYSTEM=400 ;minimum N20090 $MC_SPIND_DEF_MASTER_SPIND=??= Main spindle number frm MD35000 N20110 $MC_RESET_MODE_MASK='H04041' : bit0=1, bit6=1, bit14=1, bit16=0 N20112 $MC_START_MODE_MASK='H400' : bit10=1 N20128 $MC_COLLECT_TOOL_CHANGE=0 N20130 $MC_CUTTING_EDGE_RESET_VALUE=1 N20150 $MC_GCODE_RESET_VALUES[5]=2 N20150 $MC_GCODE_RESET_VALUES[15]=3 ;variable N20150 $MC_GCODE_RESET_VALUES[48]=3 ;variable N20152 $MC_GCODE_RESET_MODE[5]=0 N20152 $MC_GCODE_RESET_MODE[7]=1 N20152 $MC_GCODE_RESET_MODE[12]=0 N20152 $MC_GCODE_RESET_MODE[14]=1 N20152 $MC_GCODE_RESET_MODE[15]=0 N20202 $MC_WAB_MAXNUM_DUMMY_BLOCKS=10 ;minimum N20240 $MC_CUTCOM_MAXNUM_CHECK_BLOCKS=4 N20250 $MC_CUTCOM_MAXNUM_DUMMY_BLOCKS=5 N20310 $MC_TOOL_MANAGEMENT_MASK='H80400B' : bit0, 1, 3, 14, 16, 23=1 Siemens AG 2008 I DT R&D 51 Page 25 f 33