Network Update Method Page 2 (Recommended method if your Blu-ray Player is connected to the Internet.)

Transcription

1 IMPORTANT NOTICE Do not attempt to update your Yamaha Blu-ray Disc Player using any other data file except those provided directly from the Yamaha website. Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by Yamaha. Improperly updated products may cause improper operation, and any parts or service required to restore proper operation will not be covered under the Yamaha Limited Warranty. Choose your update method: There are 3 methods you can choose from. Network Update Method Page 2 (Recommended method if your Blu-ray Player is connected to the Internet.) USB Thumb Drive Method Page 3 (A USB thumb drive is required.) Update Disc Method Page 5 (Burning update file onto CD-R disc is required.) If an error occurs, see Troubleshooting section on the last page. Page.1 of 7

2 Network Update Method Requirement: -Internet connection This can be checked by selecting the Connection Test in the setup menu. See Troubleshooting section on the last page. STEP 1 STEP 2 Power on and enter Upgrade Enter SETUP menu and select System > Upgrade > Network. Wait till the Blu-ray Player finds the update file Follow the instructions on TV. When completed, Blu-ray player will reboot automatically. Please allow up to 1 minute for the reboot process to finish. note: In case Please select OK to upgrade to support 3D appears on TV, follow the instructions on TV to update. If No valid upgrade file is found! appears on TV, retry from STEP1. STEP 3 Confirm updated version. Enter SETUP menu and display System Information by pressing the [LEFT] button on the remote control. Confirm that the software version has been updated to the latest. Congratulations! You have completed the software update. Your Blu-ray Disc Player is now ready for normal use. Page.2 of 7

3 USB Thumb Drive Method Requirements: - USB thumb drive, with enough free space to store over 36MB. (File system with FAT16 or FAT32 format) - Software file provided by YAMAHA, BDS1067_Vxxxxx.zip. STEP 1 STEP 2 Copy the update file to a USB thumb drive Unzip the downloaded file BDS1067_Vxxxxx.zip. UPG folder will appear. Copy this folder to the root directory of a USB thumb drive that supports USB Mass Storage Class. (It is recommended to delete all other files or folders.) Insert the USB thumb drive USB port is located at the lower left corner, below the [power] button. USB Port STEP 3 Power on and enter Upgrade Enter SETUP menu and select System > Upgrade > USB Storage. The Blu-ray player will search for the software update file. Wait till the upgrade file is found. If the software in the USB thumb drive is the same as the software version currently in the Blu-ray Disc Player, the message No valid upgrade file is found! will appear. STEP 4 Follow the instructions on TV and start update When completed, Blu-ray player will reboot. Please allow up to 1 minute for the reboot process to finish. Page.3 of 7

4 note: In case Please select OK to upgrade to support 3D appears on TV, follow the instructions on TV to update. If No valid upgrade file is found! appears on TV, retry from STEP1. STEP 5 Remove the USB thumb drive and confirm updated version Enter SETUP menu and display System Information by pressing the [LEFT] button on the remote control. Confirm that the software version has been updated to the latest. Congratulations! You have completed the software update. Your Blu-ray Disc Player is now ready for normal use. Page.4 of 7

5 Update Disc Method STEP 1 STEP 2 Preparation of update disc Unzip the downloaded file BDS1067_Vxxx.zip. UPG folder will appear. Burn this UPG folder onto a CD-R or CD-RW as data disc with ISO9660 format. Make sure the disc is finalized. This will be your update disc. Load update disc The Blu-ray player will automatically search for the software file once the disc has been inserted. Wait till the upgrade file is found. If the above message doesn t appear automatically, enter SETUP menu and select System > Upgrade > Disc. If the software in the update disc is the same as the software version currently in the Blu-ray Disc Player, the message No valid upgrade file is found! will appear. STEP 3 Follow instruction on TV and start update Press [ENTER] on the remote control to start update. When completed, Blu-ray player will reboot automatically. Please allow up to 1 minute for the reboot process to finish. note: In case Please select OK to upgrade to support 3D appears on TV, follow the instructions on TV to update. If No valid upgrade file is found! appears on TV, retry from STEP1. Page.5 of 7

6 STEP 4 Cancel the update and remove the update disc After rebooting, the system will search for additional upgrade file from the disc again. When No valid upgrade file is found! appears on TV, cancel the upgrade and remove the update disc. STEP 5 Confirm updated version Enter SETUP menu and display System Information by pressing the [LEFT] button on the remote control. Confirm that the software version has been updated to the latest. Congratulations! You have completed the software update. Your Blu-ray Disc Player is now ready for normal use. Page.6 of 7

7 Troubleshooting <Network Update Method> Case 1: Determine if the Blu-ray Disc Player is connected to the Internet. Solution: Perform Connection Test. Enter Setup menu and select Network > Connection Test OK or FAILED will appear. In case of FAILED, check your Internet Connection settings. < USB Thumb Drive Method > Case 1: Blu-ray Disc Player cannot verify the u pdate file in the USB thumb drive. Check that the UPG folder is located in the root directory of the USB thumb drive. Check that no other folders are created in the USB thumb drive. Make sure that the USB thumb drive is not password protected. (Cannot read files from a security protected USB thumb drive) Make sure the folder and file name of the update data has not been renamed. Try using another USB thumb drive. Or, try the update disc method. Case 2: Unintended error occurred during the update. Solution: Power off and retry the update procedure from STEP 1 again. (The Blu-ray Disc Player will restore original software version) < Update Disc Method > Case 1: After loading the up date disc, the Blu-ray Disc Player doesn t automatically start the update. Make sure the update disc was finalized during the burn process. Check that the UPG folder is located at the root directory of the disc and is the only folder recorded in the disc. Make sure the folder and file name of the update data has not been renamed. Burn the downloaded update file again using another disc. (CD-R is recommended.) Or, try the USB thumb drive method. Case 2: Unintended error occurred during the update Solution: Power off and retry the update procedure from STEP 1 again. (The Blu-ray Disc Player will restore original software version) Page.7 of 7