Language Installation Program Installation Instructions Code No. LIT Software Release 3.0 Issued August 2017

Transcription

1 Code No. LIT Software Release 3.0 Issued August 2017 Refer to the QuickLIT website for the most up-to-date version of this document. LIP Document Introduction...2 Summary of Changes...2 LIP Documentation...2 LIP Concepts...2 LIP Overview...2 LIP System Requirements...3 Detailed Procedures...4 Installing the Language Installation Program...4 Obtaining Translated Language Packs...6 Troubleshooting...6 1

2 LIP Document Introduction This document describes how to install the Johnson Controls Language Installation Program (LIP), which is used to install and remove languages for Metasys servers, software applications, and supervisory engines. You can only obtain the LIP installation file from the Language Installation Program webpage on the Johnson Controls internal portal website: From this webpage, you can also download the required product configuration file and translated language packs for all Metasys system products supported by the LIP tool. Summary of Changes No technical changes were made to the document for this release. LIP Documentation For information on how to use the LIP tool, refer to the Language Installation Program Help (LIT ). LIP Concepts LIP Overview The LIP is a software tool that installs and removes a set of language resources on a Metasys platform to support multiple different languages. The tool changes the site default language for supervisory engines, Metasys servers, and Metasys software applications. For applications that support multiple languages, the LIP sets the language choices in addition to the default language. In this way, users with a different language preference can log in to the system and see the product s UI in their preferred language. The LIP tool is compatible with Release 5.2 or later. The LIP supports the following products (Table 1). Table 1: Metasys Servers, Software Applications, and Supervisory Engines Supported by LIP Type of Supervisory Supported Product Engine or Application Metasys Server Software Application and Data Server (ADS and ADS-Lite) Extended Application and Data Server (ADX) Open Data Server (ODS) Metasys Advanced Reporting System Metasys Energy Essentials NxE85/LCS85 Site Management Portal NIE89 Site Management Portal Metasys Software Applications Advanced Graphics Application (AGA) Graphic Generation Tool (GGT) Metasys Export Utility Metasys UI System Configuration Tool (SCT) with simulation Metasys Supervisory Engines NAE35 NAE45 NAE85/LCS85 NCE25 NIE29 NIE39 NAE-Lite NIE55 NIE49 NAE55 NIE85 NIE59 2

3 LIP System Requirements The LIP tool requires the following: A computer with 2 MB free hard disk space for the LIP program files and 30 MB free hard disk space for each language Windows 8.1 Professional or Enterprise with Update 1 (64-bit) or Windows 10 Professional or Enterprise with Anniversary Update (version 1607) (64-bit), Windows 7 Professional, Enterprise, and Ultimate Editions with SP1 (32-bit or 64-bit), Windows Server 2016 (64-bit) or Windows Server 2012 (64-bit), or Windows Server 2012 R2 (64-bit). Regional and language options in the operating system must be selected for your location. Note: Before using the LIP (and installing the ADS/ADX/ODS or SCT software), set the computer s regional settings and the default language used by the Microsoft SQL Server database to the same locale as the site default language. For details, consult the Microsoft documentation. Administrative rights for the user who is currently logged in A local area network connection to the supervisory controller, if you are updating a supervisory controller. The dictionary updates that the LIP performs are not supported over a dial-up connection. The presence of the Metasys server or software application that you want to update. Specifically, you must install the LIP on the same computer where the server or software application exists. For example, if you want to change the language files for AGA, you must install LIP on the computer where AGA is installed. The Microsoft.NET Framework 2.0 or higher A PDF reader for opening the online help file, such as Adobe Reader The LIP installation program verifies that the software prerequisites are present on your computer before allowing the installation. 3

4 Detailed Procedures Installing the Language Installation Program Note: If you have a previous release of LIP on the computer, the new release does not replace the older release; both releases and their respective LIP programs may exist on the same computer. To install the Language Installation Program: 1. Uninstall previous versions of the Language Installation Program tool. 2. Using a web browser on your computer, go to the following Johnson Controls internal portal website: The Language Installation Program home page appears. 3. Download the language installation program by clicking the LIP.zip link on the Language Installation Program home page. Save the file to a location on your computer. 4. Using Windows Explorer, browse to the location where you copied the LIP.zip file. Right-click on the LIP.zip file and select Extract Here. Double-click LIP.exe. The Welcome screen for the Johnson Controls - LIP Setup wizard appears (Figure 1). Figure 1: Installation Wizard for Johnson Controls LIP Setup 5. Click Install. This starts the installation and saves the tool in the location the LIP.exe file is located. To choose a location, click Custom. 6. If you clicked Custom, the Destination Folder screen appears (Figure 2). To choose an install path other than the default, click Browse... Navigate to your desired save location. Click Save. Click Install to begin the LIP tool installation. 4

5 Figure 2: Destination Folder Screen 7. While the software is installing, a progress indicator bar appears. The files copy to the folder selected in the previous step. After the LIP installs successfully, the Installation Complete screen appears (Figure 3). Figure 3: LIP Installation Complete 8. Click Finish. You do not need to restart your computer. 9. Go to Obtaining Translated Language Packs. 5

6 Obtaining Translated Language Packs To obtain translated language packs: 1. Using a web browser on your computer, go to the following Johnson Controls internal portal website: The Language Installation Program home page appears. 2. Go to the language pack files download page for the desired product by clicking its link. For example, the link for the translated language packs for Metasys system products is Metasys Language Packs. The Metasys Language Packs webpage appears. 3. Click the link for your language, then save the downloaded language pack file to your computer in the same folder as the LIP tool. Depending on your operating system, the location is either of these: C:\Program Files\Johnson Controls\LIP\ C:\Program Files (x86)\johnson Controls\LIP\ 4. Unzip the downloaded language pack file by selecting the Extract Here option. A new folder for the language files is created in the same folder as the zipped file. This language pack file contains all the languages for all Metasys servers, applications, and engines. Note: Remember this language file location because you need to specify the location when you start the LIP tool. 5. If you also need the language files for GGT, repeat Step 1 to Step 4 to obtain and unzip the GGT language files for the appropriate release. The link for the translated language packs for GGT is GGT Language Packs. This can be found in Step 5 on the Language Installation Program home page. 6. The LIP is now ready for use. To begin, double-click the LIP icon on your Desktop. For more details, refer to Language Installation Program Help (LIT ). Troubleshooting Use Table 2 to troubleshoot problems encountered when installing the LIP. Table 2: Troubleshooting the LIP User Message or Problem Explanation/Solution This program may not have been installed correctly. When exiting the LIP on a Windows 7 computer, a Program Compatibility Assistant dialog box may display this message. This issue is caused by enhanced security in Windows 7. Click This program installed correctly to dismiss the dialog box and continue. Building Technologies & Solutions 507 E. Michigan Street, Milwaukee, WI Metasys and Johnson Controls are registered trademarks of Johnson Controls. All other marks herein are the marks of their respective owners Johnson Controls Published in U.S.A. 6