Laser Barcode Scanner Model no. LS6007 FS5027

Size: px

Start display at page:

Download "Laser Barcode Scanner Model no. LS6007 FS5027"

Dulcie Peters
6 years ago
Views:

1 Laser Barcode Scanner Model no. LS6007 FS5027 User s Manual

2 FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. Limited Warranty No warranty of any kind is made in regard to this material, including, but not limited to, implied warranties of merchantability or fitness for any particular purpose. We are not liable for any errors contained herein or for incidental or consequential damages in connection with furnishing, performance or use of this material. We shall be under no liability in respect of any defect arising from fair wear and tear, willful damage, negligence, abnormal working conditions, failure to follow the instructions and warnings, or misuse or alteration or repair of the products without written approval.

3 Table of Contents 1. INTRODUCTION.. 2~3 2. INSTALLATION.....4~7 3. SET UP FROM BAR CODE LABEL...8 Multi-interface Functions. 9~11 Interface-Serial.. 12~13 1D Symbologies On/Off.14~15 2D Symbologies On/Off.16 Symbologies Set Up.17~21 Termination String Setup Bar Codes..22 1

4 Introduction 2

RIOTEC LS6007 FS5027 2D laser barcode scanner can compatible several interfaces (RS232-USB, RS-232,) and numerous configurations, is a powerful and reliable handheld scanner without compromise.

5 RIOTEC LS6007 FS5027 2D Laser barcode scanner, using Intermec engine, combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and data storage for computerized information systems. It is easy to install drivers to operate. RIOTEC LS6007 FS5027 2D laser barcode scanner can compatible several interfaces (RS232-USB, RS-232,) and numerous configurations, is a powerful and reliable handheld scanner without compromise. All the operating parameters are programmed by bar code programming menu and stored in non-volatile RAM which can retain the settings after power is turned off. LED (blue/red) Exit Window Buzzer Buzzer Trigger Handle Exit Window LED When a barcode is successful decoded, the blue LED light of the scanner will turn on and off. The scanner will beep once. 3

6 Installation Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: 1. USB cable Connection: Connect with host Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode below. This will reset the scanner to its factory defaults settings in USB interface. 2. RS232 cable Connection: connect with host Require 5V adapter for power supply 4

7 NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power adapter to RS232 cable. 1. Be sure that Host computer is turned OFF 2. Connect scanner cable to the USB port(com port) on the host system. 3..Ensure that all connections are secure. Turn on your host. 4. And please operate the scanner under the right software application. 5. Install the software PL-2303 Driver Installer.exe to the host system.. 6. Go to My Computer One click right button of mouse Administrate Device Administrator Connect Port (COM and LPT). 7. Choose Prolific USB-to-Serial Com Port, and see identify COM number, ex. COM Go to START Programs Accessories Communications Hyper Terminal. 9. Run Hyper Terminal and make the right setting: 9600, 8-data bits, NONE-parity, 1-stop bit, NONE-flow control. 10. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 11. On successful decode, the blue LED light will turn on and off. The scanner will beep once. And will show the bar code data on the screen. Detail set up on the Hyper Terminal, please see at the Figure 1 to Figure 3. 5

This will reset the scanner to its factory defaults settings.

8 Reset Configuration to Defaults If you are unsure of the scanner configuration or have scanned the incorrect codes, please scan the Reset Configuration to Defaults barcode. This will reset the scanner to its factory defaults settings. Please read following 2 barcode to reset to defaults. Load All Factory Default Pro CMD: Save as User Default Pro CMD: Load User Default Pro CMD:

If USB(HID) VERSION,PLEASE SET THE OUT PUT MODE AS USB(HID) Operation 12. Be sure that Host computer is turned OFF. 13. Ensure that all connections are secure. 14. Turn on your host.

Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 16. On successful decode, the blue LED light will turn on and off.

Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult.

9 If USB(HID) VERSION,PLEASE SET THE OUT PUT MODE AS USB(HID) Operation 12. Be sure that Host computer is turned OFF. 13. Ensure that all connections are secure. 14. Turn on your host. And please operate the scanner under the right software application, such as Notepad or Word(RS232 interface should be under Hyper Terminal and make the right setting). 15. Aim the scanner at a barcode, ensure that the scanner is in trigger mode (default), and press the trigger. 16. On successful decode, the blue LED light will turn on and off. The scanner will beep once. Tip Do not hold the scanner directly over a barcode at 90. Scanning light bounces directly back into the scanner from the barcode label is known as specular reflection which will create a "dead zone" where decoding is difficult. Practice a few times to find what range of angles works best. Maintenance Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy. Wipe the scanner window gently with a lens tissue or other material suitable for cleaning optical material. Do not spray water or other cleaning liquids directly onto the window. 7

10 Setup from Bar Code Label 8

11 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Multi-Interface Functions Please read following 2 barcode to reset to defaults. RESET CONFIGURATION TO DEFAULTS Save as User Default Pro CMD: Load User Default Pro CMD: Operating settings ** Hand-held Mode Sensor Mode Pro CMD: Pro CMD: Continuous Mode Pro CMD:

12 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Sensor Mode Timeout Sensor Mode ** High Sensitivity (= 4) Pro CMD: Pro CMD: Normal Sensitivity (= 7) Low Sensitivity (= 10) Pro CMD: Enhanced Sensitivity (= 1) Pro CMD: Program Sensitivity Pro CMD: Pro CMD:

13 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Allow Reading All = enable to read all symbologies and programming codes Prohibit Reading All = allow reading programming codes only. Pro CMD: Allow Reading All 1D Pro CMD: Prohibit Reading All 1D Pro CMD: Allow Reading All 2D Pro CMD: Prohibit Reading All 2D Pro CMD: Pro CMD:

14 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Interface Serial - 1 SERIAL BAUD RATE BAUD RATE SERIAL BAUD RATE Pro CMD: Pro CMD: SERIAL BAUD RATE SERIAL BAUD RATE Pro CMD: Pro CMD: SERIAL BAUD RATE SERIAL BAUD RATE Pro CMD: Pro CMD: SERIAL BAUD RATE SERIAL BAUD RATE Pro CMD: Pro CMD:

15 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Interface Serial - 2 SERIAL DATA BITS - 8 PARA- METERS SERIAL DATA BITS - 6 Pro CMD: Pro CMD: SERIAL DATA BITS - 7 SERIAL DATA BITS - 5 Pro CMD: Pro CMD: SERIAL STOP BITS - 1 SERIAL STOP BITS - 2 Pro CMD: SERIAL PARITY - NONE Pro CMD: SERIAL PARITY - ODD Pro CMD: Pro CMD: SERIAL PARITY - EVEN Pro CMD:

16 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: CODE 39 ENABLE 1D Symbologies On/Off - 1 CODE 39 CODE 39 DISABLE Pro CMD: CODE 93 - ENABLE CODE 93 Pro CMD: CODE 93 - DISABLE Pro CMD: CODE ENABLE CODE 128 Pro CMD: CODE DISABLE Pro CMD: CODABAR - ENABLE CODABAR Pro CMD: CODABAR - DISABLE Pro CMD: I 2OF5 - ENABLE INTERLEAVED 2 OF 5 Pro CMD: I 2OF5 - DISABLE 14

17 Pro CMD: CHINA POST 25 - ENABLE China post 2 5 Pro CMD: CHINA POST 25 - DISABLE Pro CMD: Pro CMD:

18 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: UPC-A ENABLE 1D Symbologies On/Off 2 UPC/EAN UPC-A DISABLE Pro CMD: UPC-E ENABLE Pro CMD: UPC-E DISABLE Pro CMD: EAN-8 ENABLE Pro CMD: EAN-8 DISABLE Pro CMD: EAN-13 ENABLE Pro CMD: EAN-13 DISABLE Pro CMD: Pro CMD: EAN-128 ENABLE UUC/EAN EAN-128 DISABLE Pro CMD: Pro CMD:

19 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Data Matrix -ENABLE 2D Symbologies On/Off - 1 Data Matrix Data Matrix -DISABLE Pro CMD: **Forward Direction Barcode Only Pro CMD: Both Pro CMD: Pro CMD: Backward Direction Barcode Only Pro CMD: QR Code -ENABLE QR Code QR Code -DISABLE Pro CMD: Enable Chinese-Sensible Code Chinese-Sensible Code Pro CMD: Disable Chinese-Sensible Code Pro CMD: Aztec -ENABLE Aztec Pro CMD: Aztec -DISABLE 17

20 Pro CMD: Pro CMD: PDF 417ENABLE PDF 417 PDF 417 DISABLE Pro CMD: **Forward Direction Barcode Only Pro CMD: Both Pro CMD: Backward Direction Barcode Only Pro CMD: Pro CMD: Symbologies Set Up - 1 CODE 128 CHECK DIGIT ENABLE CODE 128 CHECK DIGIT CODE 128 CHECK DIGIT -DISABLE Pro CMD: TRANSMIT UCC/EAN-8 CHECK ENABLE UCC/EAN -8 CHECK BYTE Pro CMD: TRANSMIT UCC/EAN-8 CHECK DISABLE Pro CMD: Pro CMD:

21 TRANSMIT UCC/EAN-13 CHECK ENABLE UCC/EAN -13 CHECK BYTE TRANSMIT UCC/EAN-13 CHECK DISABLE Pro CMD: TRANSMIT UPC-E CHECK ENABLE UPC-E CHECK BYTE Pro CMD: TRANSMIT UPC-E CHECK DISABLE Pro CMD: TRANSMIT UPC-A CHECK ENABLE UPC-A CHECK BYTE Pro CMD: TRANSMIT UPC-A CHECK DISABLE Pro CMD: Pro CMD: ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: NO Check, Transmit All Interleaved 2 of 5 CHECK BYTE Check, Transmit No Check Pro CMD: Pro CMD: Check, Transmit All Pro CMD: NO Check, Transmit All CHINA POST 25 CHECK BYTE 19 Check, Transmit No Check

22 Pro CMD: Pro CMD: Check, Transmit All Pro CMD: NO Check, Transmit All CODE 39 CHECK BYTE Check, Transmit No Check Pro CMD: Check, Transmit All Pro CMD: Pro CMD: ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: NO Check, Transmit All CODEBAR CHECK BYTE Check, Transmit No Check Pro CMD: Check, Transmit All Pro CMD: Pro CMD:

23 NO Check, Transmit All CODE 93 CHECK BYTE Check, Transmit No Check Pro CMD: Check, Transmit All Pro CMD: Pro CMD:

24 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Symbologies Set Up 2 EXPAND UPC-E TO UPC-A ENABLE UPC/EAN FORMATING EXPAND UPC-E TO UPC-A DISABLE Pro CMD: Expand to UPC-A ENABLE Pro CMD: Expand to UPC-A DISABLE Pro CMD: Digits Addenda ENABLE UCC/EAN-8 Addenda Code Pro CMD: Digits Addenda DISABLE Pro CMD: Pro CMD: Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD: Digits Addenda ENABLE UCC/EAN-13 Addenda Code Pro CMD: Digits Addenda DISABLE Pro CMD: Pro CMD: Digits Addenda ENABLE 5 Digits Addenda DISABLE 22

25 Pro CMD: Pro CMD:

26 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: Symbologies Set Up 3 2 Digits Addenda ENABLE UPC-E Addenda Code 2 Digits Addenda DISABLE Pro CMD: Pro CMD: Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD: Digits Addenda ENABLE UPC-A Addenda Code Pro CMD: Digits Addenda DISABLE Pro CMD: Pro CMD: Digits Addenda ENABLE 5 Digits Addenda DISABLE Pro CMD: Pro CMD:

27 ** Code Programming ON Pro CMD: ** Code Programming OFF Pro CMD: TERMINATION STRING SETUP BAR CODES Step 1 STRING# 1 TERMINATION CHAR - CR Step 2 Pro CMD: Step3 Pro CMD: Pro CMD: STRING# 1 TERMINATION CHAR - LF Step 1 Step 2 Pro CMD: Pro CMD: Step 3 25

28 Pro CMD:

29 27 Version: 1.0 Date: MAY 27, 2009 P/N:

Barcode Scanner. Model no. NuScan User s Manual

Barcode Scanner. Model no. NuScan User s Manual Barcode Scanner Model no. NuScan 5000 User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.