MobileCam/Light Pro Quick Installation Guide

Transcription

1 MobileCam/Light Pro Quick Installation Guide System Requirements Pentium-class notebook or desktop computer with an available USB port Windows 98SE/ME/2000/XP/Server 2003 Package Contents MobileCam/Light Pro USB extension cable (3ft.) Driver/Utility CD This quick installation guide Serial # Sticker For future product return or exchange, this serial # is required. Please keep it for your reference B 1

2 Layout Lens (turn to focus) Snapshot Button On/Off Light Button (on the back) Light To USB Port Figure 1. MobileCam/Light Pro Layout MobileCam/Light Pro Buttons On/Off Light Button: Press the button on the back of the MobileCam/Light Pro to activate/ deactivate the light. Snapshot Button: Press the button on the side of the MobileCam/Light Pro to take a snapshot. 2

3 Software Installation Important: Make sure the driver is installed before connecting the MobileCam/Light Pro to the USB port. Driver Installation 1. Boot up to Windows and insert the driver CD. 2. Click Start, Run. Type D:\Setup.exe, click OK. (Change D: to match your CD-ROM drive letter) For Windows 98SE/ME/2000: At the USB PC Camera window, click Next, select Complete, click Next, then click Finish. For Windows XP/Server 2003: At the USB PC Camera window, click Next, click Next again, select Complete, then click Next. Click Continue Anyway, then click Finish. Our driver has been thoroughly tested in Windows for stability. 3. Restart Windows to complete the driver installation. Connecting the MobileCam/Light Pro Important: Make sure the driver is installed before connecting the MobileCam/Light Pro to your system. Note: After the MobileCam/Light Pro has been connected, turn the lens to improve focus if needed. 3

4 Windows 98SE 1. Plug the MobileCam/Light Pro into an available USB port. 2. If prompted, click Yes to keep the newer files. 3. Restart Windows to complete the installation. Windows ME 1. Plug the MobileCam/Light Pro into an available USB port. 2. Click OK to reboot Windows. 3. When ME resumes, at the Add New Hardware Wizard, select Automatic search for a better driver (Recommended), click Next, then click Finish. 4. Restart Windows to complete the installation. Windows 2000 Windows 2000 will automatically detect and install the correct driver for the MobileCam/Light Pro. Restart Windows if prompted. 4

5 Windows XP/Server Plug the MobileCam/Light Pro into an available USB port. 2. At the Found New Hardware Wizard. For XP: Select Install the software automatically (Recommended), then click Next. For XP wsp1 or later/server 2003: Select No,not this time, then click Next. Select Install the software automatically (Recommended), then click Next. 3. If prompted, at the Hardware Installation window, click Continue Anyway, then click Finish. Our driver has been thoroughly tested in Windows for stability. 4. Click Yes to restart Windows. To verify successful installation 1. Check Device Manager to verify successful installation. Windows 98SE/ME: From the main desktop, right click My Computer, then click Properties. Click Device Manager tab. 5

6 Windows 2000/XP/Server 2003: Right click My Computer, then click Manage. Click Device Manager. 2. Double click Imaging Device(s) option and USB PC Camera with Mic... should be displayed. Sound The MobileCam/Light Pro comes with a built-in microphone. If you need this function, use the directions in this section to configure the microphone's recording level. Windows 98SE 1. In Control Panel, double click Multimedia, then click Audio tab. 2. In Recording, select USB Audio (Microphone) as the preferred device. 3. Click the microphone icon, move the slider bar up to increase the recording level. 4. Close the open windows when finished. Windows ME/ In Control Panel, double click Sounds and Multimedia, then click Audio tab. 6

7 2. In Sound Recording, select USB Audio Device as the preferred device. 3. Click Volume, move the slider bar up to increase the recording level. 4. Close the open windows when finished. Windows XP/Server In Control Panel, double click Sounds and Audio Devices, then click Audio tab. 2. In Sound recording, select PC Camera as the preferred device. 3. Click Volume, move the slider bar up to increase the recording level. 4. Close the open windows when finished. AMCAP Use this utility to easily capture video and snapshots. Video capture Windows 98SE/ME/ Click Start, Programs, USB PC Camera Plus, then AMCAP. 7

8 Important: On your very first time capturing video, click File, select Set capture file..., type in a file name with.avi extension, click Open, then click OK. An example for this file name is test.avi. You only have to do this once. 2. Click Devices. For 98SE: Check USB Audio (Microphone). For ME/2000: Check USB Audio Device. 3. Wait for an image to appear, click Capture, then Start Capture. In the drop down box, make sure Capture Audio is checked. 4. Click OK. 5. To end capture, click Capture, then Stop Capture or simply press the ESC key. 6. To save the captured video, click File, Save Captured Video As..., type in a name, then click Open. 8

9 Windows XP/Server Click the Snapshot button to start AMCAP. Important: On your very first time capturing video, click File, select Set capture file..., type in a file name with.avi extension, click Open, then click OK. An example for this file name is test.avi. You only have to do this once. 2. Click Devices, check USB Camera. 3. Wait for an image to appear, click Capture, then Start Capture. In the drop down box, make sure Capture Audio is checked. 4. Click OK. 5. To end capture, click Capture, then Stop Capture or simply press the ESC key. 6. To save the captured video, click File, Save Captured Video As..., type in a name, then click Open. 9

10 Snapshot capture Windows 98SE/ME/ Click Start, Programs, USB PC Camera Plus, then AMCAP. 2. Wait for an image to appear then click the Snapshot button. 3. In the USB PC Camera with Mic window, click File, Save As, type in a name, then click Save. Windows XP/Server Click the Snapshot button to start AMCAP. 2. Wait for an image to appear, then click the Snapshot button. 3. In the USB PC Camera window, click File, Save As, type in a name, then click Save. 1280x960 snapshot capture (AMCAP) 1. From the main AMCAP window, click Options, then click Video Capture Filter. 2. In the VGA box, move the slider to SXGA, then click OK. 3. Click Options, then click Video Capture Pin. 10

11 4. Click the down arrow next to the Output Size box, and select 640 X 480, click OK. Ulead Photo Explorer 7.0 SE Platinum Ulead Photo Explorer combines easy to use tools for acquiring, viewing, organizing, adjusting, and sharing digital images. For more detail about Ulead Photo Explorer, please refer to the PDF manual located in CD-ROM:\Ulead Photo Explorer7.0SE Platinum \Document\Manual folder of the software CD. Please note that this utility is optional and not needed for the MobileCam/Light Pro to operate. 1. Boot up to Windows and insert the driver CD. 2. Click Start, Run. Type in D:\Ulead\setup.exe, then click OK. (Change D: to match your CD-ROM drive letter) 3. Follow the on-screen instructions to install the software. 4. When prompted, enter the Ulead serial number found on the driver CD sleeve to complete the installation. 11

12 Technical Support QUESTIONS? SIIG s Online Support has the answers! Simply visit our web site at and click on Support. Our online support database is updated daily with new drivers and solutions. The answers to your problems could be just a few clicks away. PRODUCT NAME MobileCam/Light Pro FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIIG, Inc Stewart Ave. Fremont, CA MobileCam/Light Pro is a trademark of SIIG, Inc. All other names used in this publication are for identification only and may be trademarks of their respective companies. June, 2006 Copyright 2006 by SIIG, Inc.