Firmware Update Instructions. Xbox360/Xbox One Xbox One Super Converters

Transcription

1 Firmware Update Instructions Xbox360/Xbox One Xbox One Super Converters

2 This document describes how to update the firmware of the PS3/PS4 to Xbox One Brook Super Converters. NOTE The update must be done on a PC; it cannot be done on a console. NOTE These instructions are based on Windows 7. NOTE NOTE If you run Win 8 you will not need to install the patch files. It is recommended to connect the Super Converter to a USB port on the backside of desktop computers. NOTE NOTE Follow this step-by-step procedure diligently. These instructions are valid for three different Super Converter model updates, but each model uses different update files. When you download the update files for your model, you will get exactly the files you need. Double-check using the table below to ensure that you have the right files: Super Converter Model Update files PS3 -> Xbox One ZPPK002-A_(date) + ZPPK002-B_(date) PS3/4 -> Xbox One ZPP004P-A_(date) + ZPP004P-B_(date) Xbox 360 -> Xbox One ZPPK001-A_(date) + ZPPK001-B_(date)

3 STEP 1 Check your Windows version; see Appendix A to see how to do it. STEP 2 Download the zip file with the Zeroplus driver and the update files from the Brook website: Unzip the files. STEP 3 Download the official Xbox One driver from the Microsoft website: -one-controller-to-pc STEP 4 Open the Device Manager (Control Panel / Hardware and Sound / Devices and Printers / Device Manager). Plug in the Super Converter. It will show as shown in the figure below.

4 STEP 5 Double-click the Xbox driver file and follow the steps to install the driver. This might take a few minutes. STEP 6 When the Xbox driver installation has completed the Super Converter will show as Microsoft Xbox One Controller in the Device Manager: NOTE Note that the lower part of the icon will show a game controller (this is very small) if the driver installation was successful. If a yellow warning sign is shown instead of the controller please download and install two patch files; see Appendix B for how to do this. STEP 7 Proceed to update the firmware. Plug in the Super Converter and connect a controller that the Super Converter supports to the Super Converter (preferably an original controller; that is to say no 3 rd party).

5 STEP 8 Go to the downloaded files. Right-click on the A ending update file and click Run as administrator rather than double-clicking the file. The following window will show. This procedure is used to enter the Settings mode. STEP 9 Follow the steps indicated in green on the image above: First press the PS and START buttons at the same time. This will make the light of the Super Converter flash quickly. Then press and hold the LEFT STICK. With this button down, press the PS button again. When this is done you enter the Settings Mode. The Super Converter light will now be off. STEP 10 The screen will automatically change to show the following: STEP 11 The firmware update will start. Do not disconnect the Super Converter nor the controller at this point. This screen will show during the update.

6 STEP 12 When the update has finished, the light will start flashing again (about once per second). The following screen will show when finished. STEP 13 Take care to properly exit the Settings mode following the same procedure as when entering it (Press START+PS, then press and hold the LEFT STICK and press the PS button again). The Super Converter will light permanently again. STEP 14 Close the Firmware update window; the A update has finished. STEP 15 Disconnect and reconnect the Super Converter with the game controller. STEP 16 Proceed to the second update: Right-click on the -B update file you already downloaded in STEP 2 and select Run as administrator rather than double-clicking the file. The following window will show.

7 STEP 17 Follow the steps indicated on the screen: First press the PS and START buttons at the same time. This will make the light of the Super Converter flash quickly. Then press and hold the RIGHT Stick. With this button down, press the PS button again. These steps are used to enter the Settings mode of the Super Converter. NOTE For the -B update, the light will not turn off when entering the Settings mode. If the Update button in the lower left corner does not activate following the steps above, then the Zeroplus driver may not be installed yet. You can check if this is the problem by checking the status in the Device Manager as done in STEP 6. If this is the problem the Super Converter will no longer be recognized; see the photo below showing the yellow warning sign. See how to do update the Zeroplus driver in Appendix C.

8 STEP 18 Once the Zeroplus driver has been installed the following window will show when following the above procedure to enter the Settings mode: STEP 19 Disconnect the game controller (but not the Super Converter). STEP 20 Press the Update button to have the update start.

9 STEP 21 Update successful will show but only for a few seconds. The Super Converter will now be flashing slowly. STEP 22 When Update successful is no longer shown, reconnect the controller. STEP 23 Take care to properly redo the steps to exit the Settings mode (Press START+PS, then press and hold RIGHT STICK and press the PS button again).

10 STEP 24 The window will close automatically. The Super Converter will light permanently again. STEP 25 Update B is complete. Unplug the controller and Super Converter. The firmware update has been completed!

11 A. Check Windows version To determine the Windows version; right-click on Computer on the Start Menu.

12 B. Patch file installation These files are files from Microsoft. You might already have done this update, so this procedure does not apply to all users. Download two patch files from: In this example we install the 64-bit files. Double-click one of the files to start the installation. It is not important which file is installed first. Follow the steps to install the patch file. Proceed to install the second file, once again making sure the right bit-version is chosen. When the installations are complete; restart the computer to have the changes come into effect. When the computer has restarted, confirm that the Super Converter appears as Microsoft Xbox One Controller in the Device Manager as described in STEP 4. After the installation has been completed, the Super Converter s LED should turn on.

13 C. Installation of the Zeroplus driver To install the Zeroplus driver, right-click on the USB device and click Update Driver Software (there might be several USB devices so ensure that the correct one is chosen by disconnecting the other USB devices). Select Browse my computer for driver software. In the next window don t browse for the driver but select Let me pick from a list of device drivers on my computer. Click Have disk and browse and select the Zeroplus driver that was unpacked in downloaded in STEP 2. Click next to start the installation. This might take a few minutes don t panic. This screen will show when the Zeroplus driver installation has finished.

14 In Device Manager the Super Converter will show as follows: