First: Obtain a Linksys "WUSB300N for V11A" adapter kit: it contains the USB wireless

Size: px
Start display at page:

Download "First: Obtain a Linksys "WUSB300N for V11A" adapter kit: it contains the USB wireless"

Transcription

1 First: Obtain a Linksys "WUSB300N for V11A" adapter kit: it contains the USB wireless network adapter (with USB extension cable and Windows XP installation CD.) Before plugging in the adapter, verify that you are connected to the Internet via the usual copper network. You may need Internet access to install the driver. Plug in the adapter into one of the front USB ports. Windows 7 will automatically try to install the driver. If the driver was not installed, click on the pop-up message in the lower right of the screen. You should see the following information: Click on Change setting to use Windows Update: When the driver is installed successfully, you can proceed. You can verify by going to Control Panel then System (or right-click Computer then Properties), then Device Manager. Page 1 of 8

2 Part A - Windows WiFi in Infrastructure Mode Unplug your computer from the LAN by disconnecting the Cat 5 cable from either the back of the computer or the desktop jack. (If you go to Network Connections, the status of the Intel adapter will read "Network cable unplugged.") Connect to the Linksys Wireless Access Point (WAP), whose Service Set Identifier (SSID) is "L17-wireless". The security is set to WPA2-Personal, and the Shared Secret is "HelloWorld" (one word, all lower case.) This connection uses "Infrastructure" mode where a WAP or a wireless router is used to connect devices to the LAN. Verify that you have an IP address by running ipconfig /all from Command Prompt. Keep the window open. Verify that you have an Internet connection by opening any web site from a web browser. Keep the browser open. Show both windows to your professor [Mark #1] Part B - WiFi in Ad-Hoc Mode For this part, you can work in pairs. PC #1 Plug the Cat 5 cable that you disconnected in Part A, back into the LAN. Open Control Panel (Large icons View is best), Windows Firewall, and verify that Windows firewall is OFF. Open Control Panel, Network and Internet, then Network and Sharing Center. Click on Set up a new connection or network. The other useful choices, Manage wireless networks and Connect to a network are also shown below, for future reference. Page 2 of 8

3 This connection will set the adapter to Ad-Hoc mode. This allows two wireless adapters to communicate directly with each other instead of going through a WAP or wireless router. Enter a network name. Use the default Wired Equivalent Privacy (WEP) security. Enter a 10-digit security key, or equivalent (Windows will give you choices.) Page 3 of 8

4 PC #2 The Cat 5 cable should be unplugged. Verify that Windows firewall is OFF. Connect to PC #1's Ad-Hoc network using the wireless card. Give it a few seconds to settle. You should be able to ping PC #1. Keep the Command window open. Write down both PC s WiFi IP addresses (or you can type them in to Notepad, WordPad, etc.) PC #1 PC #2 Show the addresses and ping window to your professor [Mark #2] Page 4 of 8

5 Part C - Windows Network Bridging For this part, you can work in pairs. In Network Connections, create a Network Bridge between the Intel (copper) network adapter, shown as Local Area Connection and the Linksys (wireless) adapter, shown as Wireless Network Connection. PC #1 (the bridge) In the Network Connections window, click on both adapters by selecting one, holding down the control key and selecting the other. While still holding down Ctrl, right click and select Bridge Connections. PC #2 (the isolated network) From a Command Prompt, run ipconfig /release, then ipconfig /renew. Keep the command window open. Try to connect to the Internet. Keep the web browser window open. Write down PC #2 s WiFi IP Address Show the IP address and both windows to your professor [Mark #3] Page 5 of 8

6 Part D Windows Internet Connection Sharing For this part, you can work in pairs. Enable Internet Connection Sharing on the Intel (copper; Local Area Connection) adapter. Procedure D0. Remove the Bridge. First, delete the network bridge from PC #1. You may also have to select both network adapters again and remove the bridging, then delete the bridge. Procedure D1. Set a Static IP Address. On PC #1, run ipconfig /all and write down the following settings for the Ethernet adapter Local Area Connection only: IPv4 Address Subnet Mask Default Gateway DNS Server #1 DNS Server #2 (Ignore any additional DNS Servers.) Page 6 of 8

7 Procedure D1. (continued) Obtain your new Host ID from your instructor and write it down here: Your static IP address will begin with and end with this number. On the copper NIC, right click to select Properties, select Internet Protocol Version 4, click on Properties. This pops up the TCPIPv4 Properties dialog box. Click on Use the following IP address and enter your new static IP address, the same Subnet mask as before, and the same Default gateway as before. Click on Use the following DNS server addresses and enter your two DNS server IP addresses. Click on OK, then OK again. Run run ipconfig /all to verify that your static IP address was set. Do the following tests to verify that all settings are correct: 1) Ping your static IP address. 2) Ping the default gateway. 3) Ping (the Technology web server by IP address.) 4) Ping an your favourite web site by name (e.g., ca.yahoo.com.) Procedure D2. Enable Internet Connection Sharing. On the copper NIC, right click to select Properties, and switch to the Sharing tab. Under Internet connection sharing, check off Allow other network users to connect through this computer s Internet connection. On PC #2, run the ipconfig /release and ipconfig /renew again and try to connect to the Internet again. NOTE: You may need to reconnect to PC #1 s Ad-Hoc wireless network again. Page 7 of 8

8 Write down all the following information: PC #1 Copper IP Address (your static IP) WiFi IP Address PC #2 WiFi IP Address Default Gateway Show this information to your professor [Mark #4] To finish up: Disable the Internet Connection Sharing on PC #1. Change the copper NIC to TCPIPv4 settings to Obtain automatically again. Demonstrate that you have done this to your professor and get checked off on Blackboard. Page 8 of 8

Lab - Configure a NIC to Use DHCP in Windows

Lab - Configure a NIC to Use DHCP in Windows Introduction In this lab, you will configure an Ethernet NIC to use DHCP to obtain an IP address and test connectivity between two computers. Recommended Equipment Wireless router Two computers running

More information

Lab - Configure Wireless Router in Windows

Lab - Configure Wireless Router in Windows Introduction In this lab, you will configure and test the wireless settings on a wireless router. Recommended Equipment A computer with Windows installed A Wireless NIC installed An Ethernet NIC installed

More information

Lab - Connect to a Router for the First Time

Lab - Connect to a Router for the First Time Introduction In this lab, you will configure basic settings on a wireless router. Recommended Equipment A computer with Windows installed An Ethernet NIC installed Wireless router Ethernet patch cable

More information

Wireless Router Lab Created by Joshua Newell, A+

Wireless Router Lab Created by Joshua Newell, A+ Create a team of two partners. Partner closer to the wall/partition will be the Wired Partner Partner closer to the walkway will be the Wireless Partner Wired Partner: Plug the router into the power socket.

More information

Lab: Configure Wireless Security

Lab: Configure Wireless Security 16.3.1 Lab: Configure Wireless Security Introduction Print and complete this lab. In this lab, you will configure and test the wireless settings on the Linksys WRT300N. Recommended Equipment Two computers

More information

DHCP in. Introduction. Step 1 router. In this lab, you. computer. Page 1 of 7

DHCP in. Introduction. Step 1 router. In this lab, you. computer. Page 1 of 7 Essentials 5.0 6.3.2.7 Lab - Configure a NIC to Use DHCP in Windows 7 Introduction Print and complete this lab. In this lab, you will configure an Ethernet NIC to use DHCP to obtain an IP address and testt

More information

Lab IP Addresses and Network Communication

Lab IP Addresses and Network Communication Lab 3.5.2 IP Addresses and Network Communication Objectives Build a simple peer-to-peer network and verify physical connectivity. Assign various IP addresses to hosts and observe the effects on network

More information

Notebook Adapter. Quick Installation Guide WPC300N (EU/LA) Package Contents

Notebook Adapter. Quick Installation Guide WPC300N (EU/LA) Package Contents Package Contents Wireless-N Notebook Adapter Setup Wizard CD-ROM User Guide (English only) on CD-ROM Quick Installation 24, GHz Wireless-N Notebook Adapter Wireless Model No. WPC300N (EU/LA) Quick Installation

More information

Activity Configuring and Securing a Wireless LAN in Packet Tracer

Activity Configuring and Securing a Wireless LAN in Packet Tracer Activity Configuring and Securing a Wireless LAN in Packet Tracer Objectives: 1. Configure a Wireless Access Point (WAP) local IP address. 2. Configure a WAP with an SSID. 3. Change the administrator s

More information

Lab Viewing Wireless and Wired NIC Information

Lab Viewing Wireless and Wired NIC Information Objectives Part 1: Identify and Work with PC NICs Part 2: Identify and Use the System Tray Network Icons Background / Scenario This lab requires you to determine the availability and status of the network

More information

Lab 1.3.2: Review of Concepts from Exploration 1 - Challenge

Lab 1.3.2: Review of Concepts from Exploration 1 - Challenge Lab 1.3.2: Review of Concepts from Exploration 1 - Challenge Topology Diagram Learning Objectives Upon completion of this lab, you will be able to: Create a logical topology given network requirements

More information

8.9.2 Lab: Configure an Ethernet NIC to use DHCP in Windows Vista

8.9.2 Lab: Configure an Ethernet NIC to use DHCP in Windows Vista 8.9.2 Lab: Configure an Ethernet NIC to use DHCP in Windows Vista Introduction If Vista is not available in your classroom, you may complete this lab by viewing the figures in this document. Print and

More information

A Connect the Broadband Router

A Connect the Broadband Router A CheckPoint FTS Broadband Linksys WRT54G Router Setup V2 A Connect the Broadband Router PRINT THIS DOCUMENT FOR REFERENCE IMPORTANT: Before you begin, disconnect any computers that are connected to your

More information

Windows 7 Peer-to-Peer Networking

Windows 7 Peer-to-Peer Networking CTEC1767... Lab #7 Windows 7 Peer-to-Peer Networking PART A: WINDOWS 7 PEER TO PEER SETUP Boot into Windows 7 and choose (Start Menu > Control Panel > Network and Sharing Center > Change adapter settings)

More information

NETWORK LAB 2 Configuring Switch Desktop

NETWORK LAB 2 Configuring Switch Desktop Configuring Switch 1. Select the switch tab and then add a switch from the list of switches we have to the workspace, we will choose (2950-24) switch. 2. Add a number of PCs next to the switch in order

More information

Optional Lab: Install a Wireless NIC in Windows Vista

Optional Lab: Install a Wireless NIC in Windows Vista 15.5.1 Optional Lab: Install a Wireless NIC in Windows Vista Introduction Print and complete this lab. In this lab, you will install and configure a wireless NIC. Recommended Equipment A computer with

More information

4 Enter an IP address and sub-net mask for the ftp server and. 5 Go to the [System and Maintenance] > [Administrative Tools]

4 Enter an IP address and sub-net mask for the ftp server and. 5 Go to the [System and Maintenance] > [Administrative Tools] $00_WT-4_En.book Page 115 Friday, August 10, 2007 2:02 PM 4 Enter an IP address and sub-net mask for the ftp server and click [OK]. 5 Go to the [System and Maintenance] > [Administrative Tools] control

More information

StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows Vista)

StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows Vista) StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows Vista) 1. Preface To establish the wireless connection between StarBoard FX/FX-DUO and the PC, the following devices are necessary: Wireless

More information

Lab 7.5.1: Basic Wireless Configuration

Lab 7.5.1: Basic Wireless Configuration Topology Diagram Learning Objectives Configure options in the Linksys Setup tab. Configure options in the Linksys Wireless tab. Configure options in the Linksys Administration tab. Configure options in

More information

Configuring the WT-4 for ftp (Infrastructure Mode)

Configuring the WT-4 for ftp (Infrastructure Mode) Configuring the WT-4 for ftp (Infrastructure Mode) Configuring the WT-4 for ftp (Infrastructure Mode) Windows 7 This document provides basic instructions on configuring the WT-4 wireless transmitter and

More information

Configuring the WT-4 for ftp (Infrastructure Mode)

Configuring the WT-4 for ftp (Infrastructure Mode) En Configuring the WT-4 for ftp (Infrastructure Mode) Mac OS X Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Mac OS X (10.5.2) ftp server for

More information

Packet Tracer Create a Simple Network Using Packet Tracer

Packet Tracer Create a Simple Network Using Packet Tracer Using Packet Tracer Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway PC Ethernet0 DHCP 192.168.0.1 Wireless Router Cisco.com Server LAN 192.168.0.1 255.255.255.0 Internet

More information

HP Deskjet 6800 series

HP Deskjet 6800 series HP Deskjet 6800 series Network Guide 網路指南 English English Edition 1 May 2004 Copyright 2004 Hewlett-Packard Development Company, L.P. Notice Reproduction, adaptation, or translation without prior written

More information

Lesson 10. Circuit Boards and Devices Ethernet and Wi-Wi Connectivity with the Internet

Lesson 10. Circuit Boards and Devices Ethernet and Wi-Wi Connectivity with the Internet Lesson 10 Circuit Boards and Devices Ethernet and Wi-Wi Connectivity with the Internet 1 Connecting Arduino USB to Internet Arduino board IDE supports USB. USB port connects to a mobile or computer or

More information

TEEAL. Installation & network configuration for new TEEAL machine. Written By: The TEEAL Team

TEEAL. Installation & network configuration for new TEEAL machine. Written By: The TEEAL Team TEEAL Installing TEEAL Installation & network configuration for new TEEAL machine Written By: The TEEAL Team INTRODUCTION This guide will walk you through the initial setup to configure TEEAL to run in

More information

11814 South Election Rd., Suite 200, Draper, UT (801) FAX (801)

11814 South Election Rd., Suite 200, Draper, UT (801) FAX (801) DX Assistant Quick Start Guide The DX Assistant is a stand-alone local server specifically designed to support a network of DX enabled radiation detectors inside your own protected firewall. Software on

More information

TEEAL. TEEAL Configuration and Setup. Configuration & network setup for new TEEAL machines. Written By: The TEEAL Team

TEEAL. TEEAL Configuration and Setup. Configuration & network setup for new TEEAL machines. Written By: The TEEAL Team TEEAL TEEAL Configuration and Setup Configuration & network setup for new TEEAL machines Written By: The TEEAL Team INTRODUCTION This guide will walk you through the steps to configure TEEAL. Before proceeding

More information

Dual-Band Wireless A + G Access Point. Network Layout

Dual-Band Wireless A + G Access Point. Network Layout Network Layout The Dual-Band Wireless A + G Access Point has been designed for use with 802.11g and 802.11b products. With 802.11g products communicating with the 802.11b standard, products using these

More information

A+ Certification Guide. Chapter 16 (Part B) Networking

A+ Certification Guide. Chapter 16 (Part B) Networking A+ Certification Guide Chapter 16 (Part B) Networking Chapter 16 (Part B) Objectives Installing and Configuring Network Interface Cards Networking Configuration for Small Network Switches and Routers Setting

More information

Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7, Windows 8 and Mac OSx)

Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7, Windows 8 and Mac OSx) Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7, Windows 8 and Mac OSx) Wireless Setup Guide The following steps will take you through the process of setting up and connecting to your wireless

More information

Configuring the WT-4 for ftp (Ad-hoc Mode)

Configuring the WT-4 for ftp (Ad-hoc Mode) En Configuring the WT-4 for ftp (Ad-hoc Mode) Windows XP Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 ftp server

More information

WR300N Portable Wireless-N Repeater

WR300N Portable Wireless-N Repeater WR300N Portable Wireless-N Repeater Quick Start Guide Minimum System Requirements To configure your WR300N repeater your computer must meet the following minimum requirements. Any operating system can

More information

Rapidlogger Systems. EnGenius ENS202EXT Access Point

Rapidlogger Systems. EnGenius ENS202EXT Access Point EnGenius ENS202EXT Access Point This tech note describes how to setup the EnGenius Wi-Fi access point and connect it with the Rapidlogger System. This will allow you to wirelessly communicate between your

More information

TCP/IP CONFIGURATION 3-6

TCP/IP CONFIGURATION 3-6 TCP/IP CONFIGURATION 3. Type IPCONFIG /RENEW and press the Enter key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These

More information

Lab - View Wireless and Wired NIC Information

Lab - View Wireless and Wired NIC Information Lab - View Wireless and Wired NIC Information Objectives Part 1: Identify and Work with PC NICs Part 2: Identify and Use the System Tray Network Icons Background / Scenario This lab requires you to determine

More information

Lab: Install a NIC in Windows XP

Lab: Install a NIC in Windows XP 11.4.1 Lab: Install a NIC in Windows XP Introduction Print and complete this lab. In this lab, you will install a NIC, verify NIC operation, and manually configure an IP address. Recommended Equipment

More information

StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows 7)

StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows 7) StarBoard FX/FX-DUO Wireless Connection Setup Manual (Windows 7) 1. Preface To establish the wireless connection between StarBoard FX/FX-DUO and the PC, the following devices are necessary: Wireless USB

More information

Wireless Setup Instructions for Windows

Wireless Setup Instructions for Windows Wireless Setup Instructions for Windows NOTE: For successful wireless setup, you will need to have a network cable for a temporary connection to your wireless router or access point, and you must know

More information

Troubleshooting Can not access the router on

Troubleshooting Can not access the router on Troubleshooting Can not access the router on 192.168.0.1 Please note that when accessing the router s Web interface via http://192.168.0.1 you are not accessing some web site on the Internet. The router

More information

Conceptronic C54BRS4A Firmware Recovery Instructions

Conceptronic C54BRS4A Firmware Recovery Instructions Conceptronic C54BRS4A Firmware Recovery Instructions When you have a Conceptronic C54BRS4A router and the firmware upgrade has gone wrong or you cannot access the router anymore, even after resetting it,

More information

Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode)

Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode) En Configuring the WT-4 for Upload to a Computer (Ad-hoc Mode) Mac OS X Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Mac OS X (10.5.2) computer

More information

I m InTouch Installation Guide for the DSL/Cable environment with a Linksys router Models: BEFSRU31, BEFSR41 V.2, BEFSR11

I m InTouch Installation Guide for the DSL/Cable environment with a Linksys router Models: BEFSRU31, BEFSR41 V.2, BEFSR11 I m InTouch router configuration p. 1 I m InTouch Installation Guide for the DSL/Cable environment with a Linksys router Models: BEFSRU31, BEFSR41 V.2, BEFSR11 Note: Different models may vary slightly

More information

Procedure to Upgrade Verizon FiOS Router and Configure Xbox 360 to connect with Microsoft USB WiFi Adapter

Procedure to Upgrade Verizon FiOS Router and Configure Xbox 360 to connect with Microsoft USB WiFi Adapter FiOS TV & Internet Verizon DSL FAQ s Wireless Verizon Bundles Verizon Support Procedure to Upgrade Verizon FiOS Router and Configure Xbox 360 to connect with Microsoft USB WiFi Adapter Overview The current

More information

Wireless 300N 3G quick install

Wireless 300N 3G quick install Wireless 300N 3G Router quick install guide Model 524681 INT-524681-QIG-0809-01 introduction Thank you for purchasing the INTELLINET NETWORK SOLUTIONS Wireless 300N 3G Router, Model 524681. This quick

More information

Wireless Setup Instructions

Wireless Setup Instructions Wireless Setup Instructions THESE INSTRUCTIONS ARE VERY IMPORTANT TO SECURE YOUR WIRELESS NETWORK The purpose of this procedure is to "lock" your router so other users can not access your network without

More information

Congratulations on purchasing Hawking s HWPS12UG 1-Port Parallel + 2 USB Ports Wireless G Print Server. The Hawking HWPS12UG is a powerful and

Congratulations on purchasing Hawking s HWPS12UG 1-Port Parallel + 2 USB Ports Wireless G Print Server. The Hawking HWPS12UG is a powerful and Congratulations on purchasing Hawking s HWPS12UG 1-Port Parallel + 2 USB Ports Wireless G Print Server. The Hawking HWPS12UG is a powerful and convenient network printing solution that will connect your

More information

Figure 5-25: Setup Wizard s Safe Surfing Screen

Figure 5-25: Setup Wizard s Safe Surfing Screen 4. After the settings have been saved, the Safe Surfing screen will appear. Click the Norton Internet Security Suite button to install the special edition of Norton Internet Security on your computer,

More information

How to manually set up EW-7228APn to extender wireless range

How to manually set up EW-7228APn to extender wireless range How to manually set up EW-7228APn to extender wireless range 1. Find out the IP address of your computer. Have your computer get on Internet as normally, without EW-7228APn turning on. If you use a Windows

More information

Connecting the DI-804V Broadband Router to your network

Connecting the DI-804V Broadband Router to your network Before you begin Make sure that any existing Firewall Software/Devices are disabled and/or shutdown before beginning installation of your new D-Link DI-804V Broadband Router. Contents of Package DI-804V

More information

Lab: Install a Wireless NIC in Windows XP

Lab: Install a Wireless NIC in Windows XP 15.5.1 Lab: Install a Wireless NIC in Windows XP Introduction Print and complete this lab. In this lab, you will install and configure a wireless NIC. Recommended Equipment A computer with Windows XP installed

More information

1. You have a Wireless router from Edimax. We used BR-6258n as example. Your screen may look somewhat different with BR-6258n.

1. You have a Wireless router from Edimax. We used BR-6258n as example. Your screen may look somewhat different with BR-6258n. EDIMAX COMPUTER INC. 2011 Edimax Computer 3350 Scott Blvd., Building #15 Santa Clara, California 95054, USA Phone 408-496-1105 Fax 408-980-1630 www.edimax.us 1 Congratulations on your purchase of the Edimax

More information

A specific IP with specific Ports and Protocols uses a dedicated WAN (Load Balance Policy).

A specific IP with specific Ports and Protocols uses a dedicated WAN (Load Balance Policy). 21. Multiple WAN Vigor 3300Bplus has three WAN interfaces, while Vigor 3300 and Vigor 3300V both have four WAN interfaces. With the Load Balance feature, you can use multiple WAN links simultaneously.

More information

Learn How to Configure EnGenius Wi-Fi Products for Popular Applications

Learn How to Configure EnGenius Wi-Fi Products for Popular Applications Learn How to Configure EnGenius Wi-Fi Products for Popular Applications Operation Modes Access Point (AP) / WDS AP Client Bridge (CB) Repeater WDS Bridge Client Router AP Router Access Point An access

More information

Wireless-G VPN Router with RangeBooster. Quick Install Guide

Wireless-G VPN Router with RangeBooster. Quick Install Guide Wireless-G VPN Router with RangeBooster Quick Install Guide Package Contents * * * * * Wireless-G VPN Router with 2 Fixed Antennae CD-ROM with User Guide and Setup Wizard Network Cable Power Adapter Quick

More information

AirCruiser G Wireless Router GN-BR01G

AirCruiser G Wireless Router GN-BR01G AirCruiser G Wireless Router GN-BR01G User s Guide i Contents Chapter 1 Introduction... 1 Overview...1 Features...1 Package Contents...2 AirCruiser G Wireless Router Rear Panel...2 AirCruiser G Wireless

More information

802.11g Wireless Access Point

802.11g Wireless Access Point 802.11g Wireless Access Point WAP-4036 Quick Installation Guide Table of Contents Package Content... 3 Hardware Installation... 4 Initial Configuration... 5 Further Configuration... 8 Package Content 1

More information

Windows 7. Connecting to the Wireless Network for Internet Access

Windows 7. Connecting to the Wireless Network for Internet Access Windows 7 Connecting to the Wireless Network for Internet Access Wireless Settings Network Name (SSID) CCCLIBRARY Wireless Mode (network type) Infrastructure IP settings Use DHCP WEP Disabled (DHCP must

More information

SETTING UP A NETWORK CONNECTION

SETTING UP A NETWORK CONNECTION 2 Page 2 SETTING UP A NETWORK CONNECTION In order to setup ICE TV or use the FTP service to transmit files to your computer you must first setup a network connection with your router. The connection can

More information

Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7 and Mac OSx) (3GM2Wn)

Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7 and Mac OSx) (3GM2Wn) Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7 and Mac OSx) (3GM2Wn) Wireless Setup Guide The following steps will take you through the process of setting up and connecting to your wireless

More information

Lab: Install a NIC

Lab: Install a NIC 11.4.1 Lab: Install a NIC Introduction Print and complete this lab. In this lab, you will install a NIC, verify NIC operation, and manually configure an IP address. Recommended Equipment Computer running

More information

Radiolabs Bridge in a Box Setup

Radiolabs Bridge in a Box Setup Radiolabs Bridge in a Box Setup This manual will guide you through creating a point-to-point bridge using your Radiolabs equipment. Step 1: Preparing for setup. To set the bridge up, start by unboxing

More information

Part # Quick-Start Guide. SpeedStream 6500 Residential Gateway

Part # Quick-Start Guide. SpeedStream 6500 Residential Gateway Part # 007-6510-001 Quick-Start Guide SpeedStream 6500 Residential Gateway Before you begin, Verify that the following items came with your DSL kit: Step 1 > Install Line Filters 1 2 4 5 6 1 SpeedStream

More information

3G Router 431R/421R/321R/311R/221R/211R. Quick Start Guide

3G Router 431R/421R/321R/311R/221R/211R. Quick Start Guide 3G Router 431R/421R/321R/311R/221R/211R ---------------------------------------------------------- Version: 2.0----------------------------------------------------------- Check Package Contents: 3G Router

More information

Click on Close button to close Network Connection Details. You are back to the Local Area Connection Status window.

Click on Close button to close Network Connection Details. You are back to the Local Area Connection Status window. How to configure EW-7228APn/EW-7416APn as a Repeater to extend wireless range This article can apply on EW-7228APn and EW-7416APn. We used screen shots of EW-7416APn in this instruction. We recommend you

More information

Before installing this product, ensure that the following prerequisites are completed.

Before installing this product, ensure that the following prerequisites are completed. 2 Preparation 2.1 Items to Check...2-2 2.2 Connecting PC with display unit...2-6 2.3 Setting PC Network...2-7 2.4 Set the network of display unit...2-19 2-1 Items to Check 2.1 Items to Check Before installing

More information

Wireless PC Network Settings

Wireless PC Network Settings APPENDIX C This appendix provides instructions for changing the TCP/IP and radio card settings in your wireless PC. Choose the instructions appropriate for your operating system. Here is what you will

More information

Windows XP ResNet Installation Guide

Windows XP ResNet Installation Guide Windows XP ResNet Installation Guide 1.) Connecting Your Computer to the Network: What you need: a) An Ethernet card - Also called a network interface card (NIC). This may be already installed, or built-in

More information

DCP585CW Windows Network Connection Repair Instructions

DCP585CW Windows Network Connection Repair Instructions Difficulty printing from your PC can occur for various reasons. The most common reason a networked Brother machine may stop printing, is because the connection between the computer and the Brother machine

More information

Before installing this product, ensure that the following prerequisites are completed.

Before installing this product, ensure that the following prerequisites are completed. 2 Preparation 2.1 Items to Check...2-2 2.2 Connecting PC with display unit...2-5 2.3 Setting PC Network...2-6 2.4 Set the network of display unit...2-19 2-1 Items to Check 2.1 Items to Check Before installing

More information

BASICS OF PORT FORWARDING ON A ROUTER

BASICS OF PORT FORWARDING ON A ROUTER BASICS OF PORT FORWARDING ON A ROUTER FOR SECURITY DVRS 192.168.1.100 Internet Public IP Address 72.248.26.116 Private IP Address 192.168.1.1 192.168.1.150 192.168.1.200 www.nightowlsp.com Basics of Port

More information

123 Manual, LP-1522 Broadband Wireless AP/Router, Point to point/ Point to Multipoint plus Access point installation mode.

123 Manual, LP-1522 Broadband Wireless AP/Router, Point to point/ Point to Multipoint plus Access point installation mode. Wireless - Equipment 123 Manual, LP-1522 Broadband Wireless AP/Router, Point to point/ Point to Multipoint plus Access point installation mode. LP1522_M123_ENC02W 123 Manual, LP-1522 Broadband Wireless

More information

Manually Enable Wireless Windows 7 Network Connections Not Showing Up

Manually Enable Wireless Windows 7 Network Connections Not Showing Up Manually Enable Wireless Windows 7 Network Connections Not Showing Up Wireless Network Connection Enabled but Not connected Fix Windows 7 repair. This article explains how to manually set up your Windows

More information

BIPAC Broadband Firewall Router. Quick Start Guide

BIPAC Broadband Firewall Router. Quick Start Guide BIPAC 6600 Broadband Firewall Router Quick Start Guide Billion BIPAC 6600 Broadband Firewall Router For more detailed instructions on configuring and using the Broadband Firewall Router, please refer

More information

BiPAC 8501/8521. SHDSL.bis (VPN) Firewall Bridge/Router. Quick Start Guide

BiPAC 8501/8521. SHDSL.bis (VPN) Firewall Bridge/Router. Quick Start Guide BiPAC 8501/8521 SHDSL.bis (VPN) Firewall Bridge/Router Quick Start Guide Quick Start Guide Chapter 1: Introduction 2 Billion BiPAC 8501/8521 SHDSL.bis (VPN) Firewall Bridge/ Router For more detailed instructions

More information

This guide explains how to manage the network settings from your computer or your printer s control panel. See the appropriate section below.

This guide explains how to manage the network settings from your computer or your printer s control panel. See the appropriate section below. INTR.FM (A4 size) Introduction Finding the Information This guide explains how to manage the network settings from your computer or your printer s control panel. See the appropriate section below. Connecting

More information

Installing driver over the network

Installing driver over the network Installing driver over the network Command- line Definition Description Command- line Definition Description /a or /A /n or /N /nd or /ND Specifies

More information

USB2.0 Super Link Virtual Network User Guide

USB2.0 Super Link Virtual Network User Guide USB2.0 Super Link Virtual Network User Guide Product Overview USB2.0 Super Link Cable provides user-friendly linking and networking solution for more than two USB host (PCs/Notebooks) via USB 2.0/1.1 interfaces.

More information

L Operating instructions Wireless LAN PCI-Card MiMo 300 Express

L Operating instructions Wireless LAN PCI-Card MiMo 300 Express L Operating instructions Wireless LAN PCI-Card MiMo 300 Express 1. Installing the wireless LAN PCI card... Page 02 2. Installing the driver and configuration program on Windows... Page 02 3. The configuration

More information

Home Networking. A home network generally conforms to one of the following configurations

Home Networking. A home network generally conforms to one of the following configurations Home Networking A home network generally conforms to one of the following configurations A stand-alone computer connected to the Internet. A peer-to-peer network containing two or more computers with no

More information

Lab DHCP Client Setup

Lab DHCP Client Setup Lab 9.3.5 DHCP Client Setup Objective The purpose of this lab is to introduce Dynamic Host Configuration Protocol (DHCP) and the process for setting up a network computer as a DHCP client to use DHCP services.

More information

ProjectorNetTM Adapter Quick Start Guide

ProjectorNetTM Adapter Quick Start Guide ProjectorNetTM Adapter Quick Start Guide Adapter networking 1. Quick Start The ProjectorNet Adapter kit contains the following items: ProjectorNet Serial to Ethernet Adapter Cable Adapter, ProjectorNet

More information

Add a Wireless Network to an Existing Wired Network using a Wireless Access Point (WAP)

Add a Wireless Network to an Existing Wired Network using a Wireless Access Point (WAP) Add a Wireless Network to an Existing Wired Network using a Wireless Access Point (WAP) Objective A Wireless Access Point (WAP) is a networking device that allows wireless-capable devices to connect to

More information

WLAN PCMCIA Card. Quick Setup Guide WLC3010

WLAN PCMCIA Card. Quick Setup Guide WLC3010 WLAN PCMCIA Card Quick Setup Guide WLC3010 This Quick Set-Up Guide only provides you with the basic instructions for setting up these wireless adaptors on your computer. A complete User Manual that includes

More information

Networking the printer

Networking the printer Networking the printer General networking Networking overview A network is a collection of devices such as computers, printers, Ethernet hubs, wireless access points, and routers connected together for

More information

Part # Quick-Start Guide. SpeedStream 4200 Modem PPPoE Modem Router

Part # Quick-Start Guide. SpeedStream 4200 Modem PPPoE Modem Router Part # 007-0-00 Quick-Start Guide SpeedStream 00 Modem PPPoE Modem Router Before you begin, Verify that the following items came with your DSL kit: Step > Install Line Filters 7 SpeedStream Device Documentation

More information

Windows XP Remote Control Explained

Windows XP Remote Control Explained Windows XP Remote Control Explained last modified 11/30/2001 Jason Simotas www.rethinkit.com Windows XP offers two built-in options for remote control operations allowing you to view (and control) another

More information

Computer to Network Connection

Computer to Network Connection Computer to Network Connection Network Installation Steps Having a clear understanding of all the steps required to physically building a network improves the success of a project. You may need to install

More information

BiPAC 8200M. BiPAC 8200N

BiPAC 8200M. BiPAC 8200N BiPAC 8200M VDSL2 Modem BiPAC 8200N Wireless-N VDSL2 Firewall Router Quick Start Guide Billion BiPAC 8200M VDSL2 Modem/ BiPAC 8200N Wireless-N VDSL2 Firewall Router PLEASE READ THE QUICK START GUIDE

More information

Next Generation Control - Wireless Network

Next Generation Control - Wireless Network Haas Technical Documentation Next Generation Control - Wireless Network Scan code to get the latest version of this document Translation Available Networking Terms and Responsibilities Networks and operating

More information

Prestige 660H Series. Prestige 660HW Series

Prestige 660H Series. Prestige 660HW Series Prestige 660H Series ADSL 2+ 4-Port Gateway Prestige 660HW Series ADSL 2+ 4-Port Gateway with 802.11g Wireless Quick Start Guide Version 3.40 5/2005 Overview The Prestige 660H (P660H) and Prestige 660HW

More information

How to setup the range extender by using the

How to setup the range extender by using the How to setup the range extender by using the Setup Wizard in CD Disc Thank you for purchasing Edimax Wireless Access Point. We hope this instruction can help you setup the extender to extend your existing

More information

Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7 and Mac OSx)

Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7 and Mac OSx) Wireless Setup Guide (for Windows XP, Windows Vista, Windows 7 and Mac OSx) Wireless Setup Guide The following steps will take you through the process of setting up and connecting to your wireless network.

More information

A Division of Cisco Systems, Inc. GHz 2, g. Wireless-G. User Guide. Access Point WIRELESS WAP54G (EU/LA/UK) Model No.

A Division of Cisco Systems, Inc. GHz 2, g. Wireless-G. User Guide. Access Point WIRELESS WAP54G (EU/LA/UK) Model No. A Division of Cisco Systems, Inc. GHz 2,4 802.11g WIRELESS Wireless-G Access Point User Guide Model No. WAP54G (EU/LA/UK) Copyright and Trademarks Specifications are subject to change without notice. Linksys

More information

A+ Guide to Hardware: Managing, Maintaining, and Troubleshooting, 5e. Chapter 10 Networking Essentials

A+ Guide to Hardware: Managing, Maintaining, and Troubleshooting, 5e. Chapter 10 Networking Essentials A+ Guide to Hardware: Managing, Maintaining, and Troubleshooting, 5e Chapter 10 Networking Essentials Objectives Learn about hardware devices used for networking Learn about the different types of networks

More information

DSL-G624T. Wireless ADSL Router. If any of the above items is missing, please contact your reseller. This product can be set up using any

DSL-G624T. Wireless ADSL Router. If any of the above items is missing, please contact your reseller. This product can be set up using any This product can be set up using any current web browser, i.e., Internet Explorer 6x or Netscape Navigator 7x. DSL-G624T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share your

More information

Thermal Printer Configuration (EPSON)

Thermal Printer Configuration (EPSON) Thermal Printer Configuration (EPSON) STEP A : IDENTIFY THE THERMAL PRINTER MODEL Check for your EPSON printer model by finding the label on the printer. Figure 1.1 For the example above (Figure 1.1),

More information

Installing SMS without a network

Installing SMS without a network Tech Note 6 January 15, 2009 Installing SMS without a network Why would I install SMS without using a pre-existing network? The building is not yet networked but will be. Desire to keep the security system

More information

Quick Installation Guide DAP N300 Wi-Fi Range Extender

Quick Installation Guide DAP N300 Wi-Fi Range Extender N300 Wi-Fi Range Extender BEFORE YOU BEGIN Delivery Package Extender (brochure). If any of the items are missing, please contact your reseller. The User Manual and documents are available on D-Link website

More information

Supporting Networked Computers

Supporting Networked Computers CHAPTER 7 Supporting Networked Computers After completing this chapter, you will be able to: Define the main concepts of networking, including the roles of TCP/IP, IP addresses, and subnet masks. Set up

More information

Windows System. Cannot connect the Internet or open the website

Windows System. Cannot connect the Internet or open the website Cannot connect the Internet or open the website 0 1 Check Proxy... 2 2 Check IP address... 6 3 Renew IP address... 10 4 Check Network Card Driver... 12 5 Setting DNS... 20 1 Check Proxy 1 Check Proxy 1.

More information