PROGRAMMING HELP GUIDE

Transcription

1 DIGIPLEX EVO PROGRAMMING HELP GUIDE Entering Programming Mode 1) Press and hold the [0] key 2) Enter your [Installer Code] (default ) 3) Enter 4-digit [section] you wish to program 4) Enter required data While in a one can press CLEAR and you will move one step back in programming. You can now Enter any other or by pressing CLEAR again you will exit Programming Mode. Zone Programming Pg.9 [0400] is accessible only when using EVO641 and EVO641R keypads. Without section [0400], you can only program the first 96 zones of the system using sections [0001] to [0096] for the zone s serial number and input, sections [0101] to [0196] for zone parameters, sections [0201] to [0296] for report codes and sections [0301] to [0396] for zone labels. In addition, with a EVO48 panel, you can only program the first 48 zones with or without section [0400]. Enter [0400], then enter the number of the zone you want to program Zone 1 = 001 Enter the zone s 8-digit serial and 3-digit input number (The input number is not needed for module with only one input) Press [0] followed by [Enter] to clear a zone s serial number. Enter the zone s parameters (01) (*2*4***) default Enter the zone s report codes (00) (00) (00) (00) default Enter the zone s label Press [ENTER] to save and go to the next zone Pressing [CLEAR] twice will exit the zone programming menus. Press [ENTER] before pressing clear to save your modifications. Zone Definition Partition Zone Option Select one Select one (default) 1 - Entry Delay 1 Switch options 1 to 8 or 2 - Entry Delay Follow 1 - Assigned to Partition 1 [1] Auto Zone Shutdown 4 - Instant (default) [2] Bypass (default on) 5-24Hr Buzzer 2 - Assigned to Partition 2 [3] Stay Zone 6-24Hr Burglary 3 - Assigned to Partition 3 [4] Force Zone (default on) 7-24Hr Hold-up 4 - Assigned to Partition 4 [5] [6] Zone Alarm Type 8-24Hr Gas 5 - Assigned to Partition 5 off off Steady Alarm 9-24Hr Heat 6 - Assigned to Partition 6 off on Pulsed Alarm A - 24Hr Water 7 - Assigned to Partition 7 on off Silent Alarm B - 24Hr Freeze 8 - Assigned to Partition 8 on on Report Only C - Delayed 24Hr Fire [7] Intellizone D - Standard 24Hr Fire [8] Delay before Transmission E - Stay Delay 1 F -StayDelay2. In any Zone Programming option, pressing [ACC] will save the data and go to the next zone on the same option screen. Pressing [TRBL] will save the data and go to the previous zone on the same option screen. Alarm Report Code Device A Control Panel SN#:020000A2 Input Terminals Input 2 Device B Detector A: Device A: Device B: Device C: Alarm Restore Report Code Keypad Zone APR3-ZX8 Module SN#: Input 5 Input Terminals Zone# 1= 2= 3= 4= Keypad SN#: 1A Tamper Report Code Detector A SN#: COMMUNICATI CombusNETWORK # [0001] [0002] [0003] [0004] Serial# A A Tamper Restore Report Code / / / / Device C Input# N/A N/A Ademco slow, Silent Knight fast, SESCOA, Ademco express or Pager formats: Key-in desired 2-digit hex value FF for Contact ID (MEM-Key on LCD). Automatic Report Code Programming Pg. 50 Remember that the EVO panel does not have zones, but inputs. These inputs must be assigned to zones first. Example: The main panel has eight inputs. If you want zones 1 to 8 to be on the main panel you need to fill in the serial number of the main panel and input next to the zone assignment. Zones 1 to 8 does not have to be on the main panel though. Wireless Zones Wireless detectors all have a six digit serial number. These serial numbers need to be assigned to a MG-RTX3(tranceiver) as inputs. Each MG-RTX3 have 32 inputs, thus with each MG-RTX3 fitted to an EVO one can install 32 wireless zones (6 x MG-RTX3 = 192 zones). To assign wireless inputs to a MG-RTX one must enter Module Programming. ( the MG-RTX is a module) 1) Press and hold the [0]key 2) Enter your installer code (Default = ) 3) Enter section ) Enter the 8-digit MG-RTX serial number. (now you are in the module s programming) 5) Enter module section 101 for input 001 (to for input 032) 6) Fill in the 6-digit detector serial -or press the tamper switch on the wireless detector After the inputs have been created they can be assigned to zones the same as any other input. Now refer back to zone programming. Pg.1

2 Keyswitch Programming Pg.19 Keyswitch numbering [0501] to [0532] represent keyswitches 1 to 32 respectively. This feature allows you to assign a keyswitch to an addressable or hardwired detection device. Enter 3- digit [INPUT NUMBER] of Module to which keyswitch is connected. Enter 8- digit [SERIAL NUMBER] of Module to which keyswitch is connected. Keyswitch parameters [0601] to [0632] represent keyswitches 1 to 32 respectively. This feature defines the keyswitch s partition assigment and arming method. Keyswitch Partition Assignment 0 - Not assigned to a partition (default) 1 - Keyswitch Assignment to Partition Keyswitch Assignment to Partition Keyswitch Assignment to Partition Keyswitch Assignment to Partition Keyswitch Assignment to Partition Keyswitch Assignment to Partition Keyswitch Assignment to Partition Keyswitch Assignment to Partition 8 Keyswitch Definitions 0 - (default) 1 - Momentary Keyswitch (pulsed) 2 - Maintained Keyswitch (latched) 3 - Generates a Utility Event Event on Open 4 - Generates a Utility Event Event on Open and Close Keyswitch Options (default: all Off) [ 3] - Disarm Only [ 4] - Off = Disarm On = Disarm only if Stay/ Instant armed [ 5] - Arm Only [ 6] - * Stay Arming [ 7] - * Force Arming [ 8] - * Instant Arming * Select only one. If all Off Keyswitch will regular arm 8-digit Serial Number Input# Define Assign Keyswitch Options [0501] / / / / / / / / / [0601] [0502] / / / / / / / / / [0602] [0503] / / / / / / / / / [0603] (3035) will automatically fill in the report codes for Keyswitch Arm/Disarm or they could be filled in individually at sections (0701) to (0832).Pg.20 Panic Input The above mentioned KEYSWITCH inputs may be programmed as a Panic, Medical or Fire input. These inputs will follow the Auxiliary Panic inputs enabled as shown below. After assigning a input in any position at section (0501) to (0532) the Panics are defined at sections (0601) to (0632) as follow: Example: (0601) First Digit (5) Second Digit (1) Then enable Options 1 to 8 5-Always 1-Panic 2-Medical 3-Fire Select Partition Assignment [0601] [0602] Partition Panic Alarm Options NB! the below mentioned options must be enabled for the above mentioned input to work on the required partition. Partition 1 [3123] Partition 2 [3223] Partition 3 [3323] Partition 4 [3423] Partition 5 [3523] Partition 6 [3623] Partition 7 [3723] Partition 8 [3823] Option ( = Default Setting) [1] Panic 1 (Keys 1 & 3)Panic [2] Panic 2 (Keys 4 & 6)Medical [3] Panic 3 (Keys 7 & 9)Fire [4] Panic 1 Alarm Type ( = Report Only; = Audible Alarm) [5] Panic 2 Alarm Type ( = Report Only; = Audible Alarm) [6] Panic 3 Alarm Type ( = Report Only; = Fire Alarm) [7] Always Report Disarming ( = Always; = Only After Alarm) [8] Auto-Force on Regular Arming Remember to fill in the Special Reporting codes for reporting in sections (3930) to (3932). PGM Activation for Radio could be achieved with PGM Event group 030 (pg.24). Common Partition Timers Pg.43 Partition 1 Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8 1) Press and hold the [0] key. Decimal Values from 000 to 255 Data 2) Enter your INSTALLER CODE Exit Delay Timer 3) Enter the Timer SECTI NUMBER. (Data x 1 second; Default = 060 seconds) [3108] / / [3208] [3308] [3408] [3508] [3608] [3708] [3808] 4) Fill in desired 3 digit timer. Example Entry Delay for 30 seconds. When you fill in (Data x 1 second; Default = 030 seconds) [3111] / / [3211] [3311] [3411] [3511] [3611] [3711] [3811] the last digit the time will be saved Entry Delay 2 and the programming will move onto (Data x 1 second; Default = 060 seconds) [3112] / / [3212] [3312] [3412] [3512] [3612] [3712] [3812] the next section or ask you to fill in a Bell Cut-off Timer [3113] / / [3213] [3313] (Data x 1 minute; Default = 4 minutes) [3413] [3513] [3613] [3713] [3813] new section. One does not have to press ENTER after a time has been Special Arming Exit Delay [3130] / / [3230] [3330] [3430] [3530] [3630] [3730] [3830] (Keyswitch,auto arming,winload etc.) filled in. Dialer Timers Pg.39 Auto-Arm Times Pg. 42 No Movement Auto Arming Schedule Pg. 47 Timings Pg.2

3 Options 1) Press and hold the [0] key. 2) Enter your INSTALLER CODE (Default: ) 3) Enter the Option SECTI NUMBER. 4) Turn desired Options 1to8 or by pressing on that digit. The corresponding number will lite up on the Keypad. To Disable an Option press on a lit digit. 5) Press the ENTER key. You will automatically be in the next. Change the data or press CLEAR and enter another. Example: System Options Pg.36, 37 Dialer Options Pg.38 Other Options Pg Partition Options Pg = Default setting SECTI [3031] : Partition Options 1 SECTI [3032] : Partition Options 2 [1] Partition 1 [1] Bell/siren output in partition 1 [2] Partition 2 [2] Bell/siren output in partition 2 [3] Partition 3 [3] Bell/siren output in partition 3 [4] Partition 4 [4] Bell/siren output in partition 4 [5] Partition 5 (EVO192 only) [5] Bell/siren output in partition 5 [6] Partition 6 (EVO192 only) [6] Bell/siren output in partition 6 [7] Partition 7 (EVO192 only) [7] Bell/siren output in partition 7 [8] Partition 8 (EVO192 only) [8] Bell/siren output in partition 8 Programmable Outputs Pg.21 Event Group Feature Group Start # End # The PGMs are not Pre-Programmed PGM Programming Suggested PGM programming: PGM Activation PGM1 [0910] / / [0911] / / [0912] / / [0913] / / PGM1 Arm/Disarm LED( - trigger only) PGM2 [0920] / / [0921] / / [0922] / / [0923] / / PGM2 Radio Panic( - or + trigger ) PGM3 [0930] / / [0931] / / [0932] / / [0933] 0 / / 0 0 PGM3 Radio Burglary( - or + trigger ) PGM4 [0940] / / [0941] / / [0942] / / [0943] 0 / / 0 0 PGM4 Radio Open/Close( - or + trigger ) PGM5 [0950] / / [0951] / / [0952] / / [0953] / / PGM5 Onboard Relay PGM Deactivation PGM1 [0914] / / [0915] / / [0916] / / [0917] / / NB! Change Jumper (JP1) position for + or - trip for PGMs 2, 3 and4 PGM2 [0924] / / [0925] / / [0926] / / [0927] / / PGM3 [0934] / / [0935] / / [0936] / / [0937] / / PGM4 [0944] / / [0945] / / [0946] / / [0947] / / PGM5 [0954] / / [0955] / / [0956] / / [0957] / / Event Group Event Feature Group Feature Start # End # 023 Zone Bypassed 024 Zone in Alarm 000 Zone Numbers 025 Fire Alarm 255=anyZone# Check the PGM Programming list from page 22 to 27 Note! For Panic and Burglary Radio triggers you need PGMs to pulse, thus PGM 2 and 3 need to follow the PGM Timer and not the Deactivation Event. Go to sections [0929] and [0939] and turn Option 1 for each. PGM Options Option ( = Default Setting) Other Programming PGM1 [0919] PGM2 [0929] Data PGM1 Delay [0918] / / (001to255x1sec./mins.) PGM2 Delay [0928] / / (001to255x1sec./mins.) PGM3 Delay [0938] 0 / / (001to255x1sec./mins.) 0 2 PGM4 Delay [0948] / / (001to255x1sec./mins.) PGM5 Delay [0958] / / (001to255x1sec./mins.) PGM3 [0939] (1*******) PGM4 [0949] PGM5 [0959] [1] PGM Deactivation After ( = Deactivation Event; = PGM Timer) [2] PGM Base Time ( = Seconds; = Minutes) Setting the Time and Date: 1) Enter the [Master Code] (default-1234) 2) TBL] key 3) 8] key 4) Enter the Time and Date. Changing the Installer Code 1) Press and hold the [0] key 2) Enter your [Installer Code] (default ) 3) Enter section [1000] 4) Enter the new Installer Code Usefull s [4000] - Displays the serial numbers of Panel and all Modules connected to the panel, use [ ] and [ ] to scroll. [4001] - Reset a module s programming by entering its serial number. [4002] - Locate/Unlocate a module by entering the serial number the module s Locate LED will flash. [4003] - Module Programming Mode, by entering the serial number of a module one can program the module. [4004] - Module data broadcasting can be done from here. First enter the source module s serial number then the other same type and version modules serial number/s. Press [ACC] to start transfer. [4005] - Quick module scanning will erase any module removed from panel from its memory. [4006] - Module Scanning that is the same as above, but you can add modules newly connected to the bus. Installer Function Keys To access the installer functions, press and hold the [0] key, enter the [INSTALLER CODE], and then press the KEY below: [STAY ] Test Report: Sends the Test Report report code programmed in section [3902] to the monitoring station. [FORCE] Call WinLoad Software: Will dial the PC telephone number programmed in section [3010] in order to initiate communication with a computer using the WinLoad software. [ARM] Answer WinLoad Software: Will force the control panel to answer a call made by the Monitoring Station that is using the WinLoad software. [DISARM] Cancel Communication: Cancels all communication with the WinLoad software or with the Monitoring Station until the next reportable event. [MEM] Installer Test Mode: The installer test mode will allow you to perform walk tests where the bell or siren will squawk to indicate opened zones. MEM] button again to exit. Partitions cannot be armed if the Installer Test Mode is enabled. [TRBL] Start Module Scan: The keypad will display the serial number of each module on the combus. [ACC] Combus Voltmeter: To verify if the combus is supply ing sufficient power, press and hold the [0] key, enter the [INSTALLER CODE] and press the [ACC] button. A reading of 12.3V or lower at the panel s service ke ypad connector indicates that the voltage is too low. The voltage may drop during the control panel battery test. Pg.3

4 Dialer Settings To the Panel for telephone reporting you need to do the following: 1) While in Programming Option 3 in [3036]. 2) Then enter the client s Account number in [3061]. Note to enter the same account number in s [3062] to [3068] if more than 1 Partition is used. 3) Enter 5555 in section [3070] to make sure you are using the Contact ID format. Make sure the control room set the client up with the same format. 4) Enter the base telephone number in section [ 3071]. Press ENTER when you get to the last digit. 5) Go to section [4032] and then [4037]. This will fill in all the Zone and Trouble reporting codes. If it is a business, go to section [4033] and [ 4035] as well. Account Numbers MSTN = Monitoring Station Telephone Number Data - Hex Value ( FFFF) Default [3061] / / / (if less than 4 digits, press [ENTER]) ACCOUNT NUMBER 0000 [3062] Partition 2 [3063] Partition 3 [3064] Partition 4 [3065] Partition 5 [3066] Partition 6 [3067] Partition 7 [3068] Partition 8 Reporting Formats [3070] REPORTING FORMATS FOR TELEPHE NUMBERS 1 TO 4 0-Ademco slow/1-silent Knight fast/2-sescoa/3-ademco Express/5-Contact ID/6-SIA FSK/7-Pager Use the same format for each number. Only the pager format can be used with other reporting formats. Data (Press [ENTER] if less than 32 digits) [3071] / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / MITORING STATI /PAGER TELEPHE #1 [3072] Second Base Number [3073] Third Base Number [3074] Fourth Base Number Special Telephone Number Keys Function LCD Grafica Function LCD Grafica [STAY ] Clear [CLEAR] Left action key (Clear) * # [FORCE] [#] Delete [TRBL] Switch to Tone Dialing (T) [ARM] (press key until desired Delete from cursor to the end [ACC] Wait for second dial tone (W) [DISARM] letter/symbol appears) Insert space [ MEM] 4-second pause (P) [BYP] Dial 9 for outside line 9+[STAY ] Only the SIA format supports the [0} digit in its account numbers. Enter the [STAY]=A digit in its place. When using the SIA Format, and the Account Number Transmission (see option [6] in section [3045] on page 37 correspond tothe partition, the control panel only uses the Partition 1 Account Number programmed in section [3061], but the report code includes the account number Automatic Report Code Programming When using Contact ID or SIA Reporting formats (section [3070] on page 36), default report codes can be programmed automatically. After automatic defaults are set, they can be changed and the remaining report codes can be set manually. [4030] ALL REPORT CODES RESET TO 00 Resets all the report codes from sections [0201] to [0296], [0701] to [0832], [2001] to [2199] and [3900] to [3999] to 00. [4031] ALL REPORT CODES RESET TO FF [0201] to [0296], [0701] to [0832], [2001] to [2199] & [3900] to [3999] [4032] ZE ALARM/ALARM RESTORE AND ZE TAMPER/TAMPER [0201] to [0296] RESTORE REPORT CODES [4033] USER/KEYSWITCH ARMING &DISARMING REPORT CODES [0701] to [0832], and [2001] to [2199] [4034] SPECIAL CODES [3900] to [3909] [4035] SPECIAL ARMING/DISARMING REPORT CODES [3910] to [3929] [4036] SPECIAL ALARM REPORT CODES [3930] to [3939] [4037] TROUBLE &TROUBLE RESTORE REPORT CODES [3940] to [3999] 1 Functions 2 Telephone Numbers VDMP3 Voice dialer module Select the following options to enable voice reporting and arm/disarm function. [1] Arm/disarm (default 1 and 2 ) [3090] [2] Voice reporting Program up to 8 telephone numbers which will be called in sequence in the event of an alarm. Telephone numbers should be programmed in priority sequence as the VDMP3 will start with telephone number 1. For extra key functions, see Special Telephone Number Keys on page 40. [3091] [3091] Telephone number 1 [3095] Telephone number 5 to [3092] Telephone number 2 [3096] Telephone number 6 [3098] [3093] Telephone number 3 [3097] Telephone number 7 [3094] Telephone number 4 [3098] Telephone number 8 3 Numbers 5 Features (PGM) Choose which telephone numbers will be enabled for each partition in your system. Options [1] to [8] represent telephone numbers 1 through 8. (Default: Telephone number 1 is enabled for all partitions.) [3133] [3133] Partition 1 [1] to [8] [3533] Partition 5 [1] to [8] to [3233] Partition 2 [1] to [8] [3633] Partition 6 [1] to [8] [3833] [3333] Partition 3 [1] to [8] [3733] Partition 7 [1] to [8] [3433] Partition 4 [1] to [8] [3833] Partition 8 [1] to [8] Features in this section correspond to utility key PGMs in the EVO control panel. For more information, see Feature Activation (PGMs). [3087] Options [1] to [8] represent features 1 to 8 (default: ) Remote Control Programming 1) First assign the remote to a user in User Code Programming. 2) Go to section[2900] and choose your remote button functions: (18) (20) MG-REM1 MG-REM2 Default (1 B) (C 0) Button 1 Button 2 Button 3 Buttons 2+3 Disarm Regular Arm Utility Key 1 3) At [2940] enter (00). Utility Key Disarm: cannot be modified Choose 1 function for each button Entry Function Entry Function [0] Button [8] Panic 1 [1] Regular Arm [9] Panic 2 [2] Stay Arm A = [stay] Panic 3 [3] Instant Arm* B = [force] Utility Key 1 [4] Force Arm* C = [arm] Utility Key 2 [5] N/A D = [disarm] Utility Key 3 [6] N/A E = [byp] Utility Key 4 [7] N/A F = [mem] N/A Pg.4

5 User Code Programming Note: Each option is considered when the number appears within the brackets Enter the Master Code (Default:1234) Enter Programming Mode By Pressing [0) then [ACC] Select User (002 =user 2) Enter Desired User Code (Pin) User Options [1] [2] Master Feature Master - user can program user access codes only Full Master - user can program user access codes, options, and assignments [3] Duress [6]Stay & Instant Switch Options [4] Bypass [7]Force 1to8or On default all [5] Arm Only[8] = Access keypad s partitions users can = Access user s partitions Regular Arm * Note: all users can regular arm User Options User Area Assignment Access Level and Schedule Assignment Enter Digits Press [ENTER] here if you do not need to program Access Control. You will move to Step10 Switch Options 1to8or Make sure that the user has a Partition enabled or else the code will not work. Partition Assignment [1] User Code has Access to Partition 1 [2] User Code has Access to Partition 2 [3] User Code has Access to Partition 3 [4] User Code has Access to Partition 4 [5] User Code has Access to Partition 5 [6] User Code has Access to Partition 6 [7] User Code has Access to Partition 7 [8] User Code has Access to Partition 8 Access Level & Schedule Assignment First Brackets: Access Level Enter Level from 00 to 15 (00 = all doors) Second Brackets: Schedule Enter number from 00 to 15 (00 = all times) Access Control User Options Access Card Assignment Remote Control Assignment User Label Press [ ENTER] to advanced to save and advanced to next user If no Remote press [ENTER] for Label or [CLEAR] for next user If no Label press [ENTER] You must ENABLE option 1 for ACCESS Access Control Options CTROL [1] Access Control [2] Can Disarm with Access Card [3] Card with Door Unlocked Period Extension [4] [5]Feature off offcannot Arm with Card (armingdisabled) on offcan Regular Arm with Card off oncan Stay Arm with Card on oncan Force Arm with Card [6] Add Tolerance Window to Schedules [7] off = Code can arm, disarm & access anytime on = Code follows Schedule [8] off = Valid Card can be granted access and disarm partition on = Valid Card can be granted access, Access Card Assignment Enter Access Card's serial number manually or present Card to the reader. Remote Control Assignment* Enter remote control s serial number manually or press a remote button twice. Access Control (For ACCESS modules and READERS) Programming Overview: Steps 1, 2 and 6 are the MINIMUM requirement to program Access Control: 1. Access Control in section [3038] option [1]. 2. Assign the Doors in sections [2201] to [2232] by entering the DGP-ACM12 or access keypad s serial number for each door. 3. Optional: Create up to 15 Access Levels in sections [2601] to [2615]. Assign certain combinations of doors to a level or levels 01 to 15. These Access Levels could then be assigned to Users in User Code Programming( Step 7: Default = 00 = User have access to all doors). 4. Optional: Create up to 32 Access Schedules in sections [2401] to [2432]. Assign different time periods for access next to each schedule. These schedules could then be assigned to Users in the User Code Programming( Step 7: Default = 00 = User have access at all times). 5. Optional: Enter Holidays in sections [2710] to [2712], which will disallow access o those days unless (H) is selected next to the user s Level. 6. Program the User Codes( Pg.12 User manual or above in this guide steps 7 to 9). NB! The Access module is set to Partition 1 on default. To change this enter Module Programming (section [4003] Pg.3 in this guide) and change this in section [001]. Pg.5