RoastLogger Arduino/TC4 driver installation for Windows 9/10/13 By John Hannon (JackH) at Homeroasters.org
|
|
- Britton Greene
- 5 years ago
- Views:
Transcription
1 This procedure was written for the Arduino Uno board with the TC4 shield. Please check the Arduino site for software if you are using a different model. I have not tested it, but this procedure should also work with the TC4C board which is an all in one board combining a TC4 and Arduino. **Note: The TC4 board defaults to sending temperature values in Celsius. To use Fahrenheit, a jumper is added to the TC4 board at location ANLG2 from center pin (AN1) to right pin (Ground). Using a two pin jumper (as used on computer boards) is convenient. Loading the Arduino application: (All Screens shown Windows 7) it will look different for other versions. Do not plug the Arduino into the USB port at this time. You might want to unplug all USB devices until the procedure is complete (just in case). Download the latest Arduino installer file from: Version is used at this writing. Choose the Windows Installer. It is much easier to do than downloading the zip file. Running the Installer should show the following screen after the license agreement: Page 1 of 14
2 Leave everything as is and click next. On the next screen, leave the Destination Folder as is and click Install. If it asks to load the Arduino USB driver select install. Click close to complete. Once the Arduino software loads and is complete, plug the Arduino into the USB port on your computer. XP Users: XP users will get a screen "New Hardware Wizard" Select ---> "Install from a specific location. (Advanced)" Next screen: Select ---> "Don't search. I will choose the driver to install" Next Screen: "Arduino Uno" should appear in the device list. Select: Next. Click finish to complete. Windows 7 Users: Windows 7 should see it and connect using the loaded driver. If it tries to use Windows update to find it, click on the blue highlighted text "Skip obtaining driver software from Windows update" and let it use the loaded (local) driver. You should get the following screen (Windows 7): Note the COM port it used. This number may be different. Click close Check the Device Manager to see if the Arduino driver is present: XP Users: Start--> Control Panel--> System--> Hardware--> Device Manager Tab. Select Ports (Com & LPT) in the list. Arduino Uno(COMX) should be there (X= com number assigned) Windows 7 Users: Start--> Control Panel ---> Device Manager ---> Ports and it should display "Arduino Uno (COMX)" - X = whatever number was assigned. Page 2 of 14
3 Load the RoastLogger TC4 Sketch file and libraries Now that the Arduino software and USB driver is installed, the TC4 "Sketch" file and Arduino library files specific to the TC4 need to be loaded. This is the software that runs in the Arduino and passes data from the TC4 board to the RoastLogger application. Download the latest RoastLogger TC4 sketch from: Choose the file "RoastLoggerTC4_2.0a.zip" - this is the latest version. At the next screen, click on the link --- RoastLoggerTC4_2.0a.zip and it will download. The file is a.zip and should be downloaded and then extracted to a folder on your desktop for now. You will need to copy all the folders in the "RoastLoggerTC4_2.0a/Libraries" folder (7 total) to the Arduino software Libraries folder location "C:/Program Files/Arduino/Libraries" as shown: Page 3 of 14
4 The result of the copy: Your C:/program Files/Arduino/Libraries folder should look like this: The highlighted folders you copied are for the TC4. Now that the libraries are in place we can now load the TC4 RoastLogger Sketch. Run the Arduino application and make sure the Arduino is selected to what model you have (Arduino Uno in the example) Page 4 of 14
5 Also make sure the COM port is correct and selected. A check mark should be next to COM: Next, load the TC4 Sketch located in the RoastLoggerTC4 directory we unzipped earlier: File -->Open-->RoastLoggerTC4 Page 5 of 14
6 This is what you will see when it loads: Now we need to compile at first to see if the libraries are in place. Select Sketch --> Verify/Compile: Page 6 of 14
7 You should get "done compiling at the bottom of the screen if not re-check your TC4 library file locations: Now select File --> upload to send the program to the Arduino: "Done uploading" should be displayed on the bottom. Page 7 of 14
8 If you have the optional LCD Adapter for the TC4, It should initialize and display "Roastlogger TC4 Version 2.0" for a few seconds. Then you should see roughly the following: If you do not have the LCD option, another check that the TC4 is outputting data correctly is to run the Serial Monitor in the Arduino program. Page 8 of 14
9 At first there will be odd characters displayed. Make sure the right Com port is selected and select a baud rate of 115,200 from the drop down menu. You should see the following data scrolling on the display if all is OK. Next up is to load the Roastlogger application. Page 9 of 14
10 Loading the RoastLogger application Download the latest RoastLogger application for Windows (RoastLogger.zip) from: Extracting the zip on your desktop creates two directories: "_MACOSX" and "RoastLogger" We will use the RoastLogger directory. Make sure you have the latest version of JAVA installed. Click on the directory and double click the RoastLogger.jar file. Page 10 of 14
11 The RoastLogger program should start: And the main menu --- Select the Inputs tab and then the Arduino Tab: The COM port should be the same as earlier and leave the baud rate as is. Click on Start. Page 11 of 14
12 After a few seconds you should see some temperature values in the Arduino Controller window under Temps - T1 / T2 *The readings are usually approximate ambient temperature. Fahrenheit is shown here. Page 12 of 14
13 From here it is just setting the options to what you want. Under Actions there are some default settings you may want to clear so it does not set the heater or fan do something you do not want. The Action temperature settings are in Celsius by default: Here it is set to change the Heater to a level of 65 at a T1 Temperature of 178C. You can set it to zero or whatever you want by double clicking on the value. To change the temperature selection, ranges and time ranges select from the top menu of the Roast Logger with Arduino Controller screen Options Set Chart Axes. You can also set many features including the display of RoR (Rate of Rise) values. Page 13 of 14
14 This was just some basic instructions to get started and mainly for loading the RoastLogger Arduino TC4 sketch. An excellent RoastLogger manual is available for download that covers all of the RoastLogger options and settings in detail is at: Page 14 of 14
TA0297 WEMOS D1 R2 WIFI ARDUINO DEVELOPMENT BOARD ESP8266
TA0297 WEMOS D1 R2 WIFI ARDUINO DEVELOPMENT BOARD ESP8266 Contents 1. Overview TA0297... 3 2. Getting started:... 3 2.1. What is WeMos D1 R2 Wifi Arduino Development Board?... 3 2.2. What is IDUINO UNO?...
More informationSeeMeCNC Guides. Step 5: Installing the Firmware. This guide will show you how to install the firmware on your Rostock MAX v3 3D printer.
SeeMeCNC Guides Step 5: Installing the Firmware This guide will show you how to install the firmware on your Rostock MAX v3 3D printer. Written By: geneb 2016 seemecnc.dozuki.com Page 1 of 7 Step 1 Download
More informationDot Matrix Indicator Programming
Dot Matrix Indicator Programming Preparation: USB Dongle and USB cable. Part No. 100-159 (see page 3 Dongle Installation Instruction ). Display Programmer V2.0 (see page 10 Display Programmer V2 Installation
More informationUSB SERIAL ADAPTOR COM PORT INSTRUCTIONS
USB SERIAL ADAPTOR COM PORT INSTRUCTIONS No part of this work covered by the copyright hereon may be reproduced, copied, transferred or distributed in any form or by any means -- graphic, electronic, or
More information1) Installing Bluetooth software for Windows (A) Place installation CD into PC and setup should launch automatically.
1) Installing Bluetooth software for Windows (A) Place installation CD into PC and setup should launch automatically. If setup does not launch, use Windows Explorer to navigate to the appropriate CD- ROM
More informationCipherLab Workstation Setup (Windows 7/8/10)
CipherLab Workstation Setup (Windows 7/8/10) These installation instructions will step you through setting up the CipherLab docking cradle and device, as well as installing the drivers and software used
More information'phred dist acd.tar.z'
Phred is free for academic use but does require registration and for you to obtain a licence. Please visit http://www.phrap.org/consed/consed.html#howtoget and follow the instructions. A copy of the Phred
More informationArduino 01: Installing the Arduino Application and Firmware. Jeffrey A. Meunier University of Connecticut
Arduino 01: Installing the Arduino Application and Firmware Jeffrey A. Meunier jeffm@engr.uconn.edu University of Connecticut About: How to use this document I designed these tutorial slides to be tall
More informationUSB SERIAL ADAPTOR COM PORT INSTRUCTIONS
USB SERIAL ADAPTOR COM PORT INSTRUCTIONS No part of this work covered by the copyright hereon may be reproduced, copied, transferred or distributed in any form or by any means -- graphic, electronic, or
More informationWindows XP - MVX Printer Driver Installation
Windows XP - MVX Printer Driver Installation READ FIRST! This document assumes you have already downloaded the driver installer ZIP package from either the Universal Laser Systems website or Universal
More informationDENSITRON USB KIT HARDWARE AND SOFTWARE MANUAL. Copyright 2006 DENSITRON TECHNOLOGIES plc. All rights reserved. Proprietary Data
DENSITRON USB KIT HARDWARE AND SOFTWARE TABLE OF CONTENTS 1 Introduction... 4 1.1 HARDWARE FEATURES... 4 1.2 SOFTWARE FUNCTIONS... 4 2 PARTS OF SUPPLIED SYSTEM... 5 3 SYSTEM REQUIREMENTS... 5 4 START-UP...
More informationXIV. XV. XVI. XVII. Manufacturer reserves the right to change the contents of this manual without notice.
Content Pages I. Software Overview 1 o What is Digitorq?...1 II. Software Requirement and Initial Information 1 III. Reminders 2 IV. Set up Procedures.2 o How to Install the software..3 o Why do we need
More informationTA0139 USER MANUAL ARDUINO 2 WHEEL DRIVE WIRELESS BLUETOOTH ROBOT KIT
TA0139 USER MANUAL ARDUINO 2 WHEEL DRIVE WIRELESS BLUETOOTH ROBOT KIT I Contents Overview TA0139... 1 Getting started: Arduino 2 Wheel Drive Wireless Bluetooth Robot Kit using Arduino UNO... 1 2.1. What
More informationThis is the Arduino Uno: This is the Arduino motor shield: Digital pins (0-13) Ground Rail
Reacting to Sensors In this tutorial we will be going over how to program the Arduino to react to sensors. By the end of this workshop you will have an understanding of how to use sensors with the Arduino
More informationROBOTLINKING THE POWER SUPPLY LEARNING KIT TUTORIAL
ROBOTLINKING THE POWER SUPPLY LEARNING KIT TUTORIAL 1 Preface About RobotLinking RobotLinking is a technology company focused on 3D Printer, Raspberry Pi and Arduino open source community development.
More informationThis tutorial will show you how to take temperature readings using the Freetronics temperature sensor and an Arduino Uno.
This tutorial will show you how to take temperature readings using the Freetronics temperature sensor and an Arduino Uno. Note that there are two different module types: the temperature sensor module and
More informationGo!Control Firmware Update Tool (for PC) Installation and Operation Quick Start
Go!Control Firmware Update Tool (for PC) Installation and Operation Quick Start May 1, 2012 Overview This document provides instructions for using the Firmware Update Tool to update a Go!Control panel
More informationThese instructions were adapted from Arduino: Installing Standard Firmata which is licensed under Attribution- NonCommercial-ShareAlike 2.
These instructions were adapted from Arduino: Installing Standard Firmata which is licensed under Attribution- NonCommercial-ShareAlike 2.5 Generic Step 1: Download and Install Arduino Application Your
More informationInstructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set
Instructions for Installing FlashUpdate and Downloading Updates for NPRT 2200 Noise Power Ratio Test Set Updates to the instrument firmware are available from the Applied Instruments website. Requirements
More informationAndyMark Arduino Tutorial
AndyMark Arduino Tutorial Tank Drive June 2014 Required: Required Software List: - Kit Arduino IDE - Robot Power Cable Kit (am-0975) RobotOpen Arduino Shield Software - Battery Base Package (am-0477) RobotOpen
More informationNavigator Software User s Manual. User Manual. Navigator Software. Monarch Instrument Rev 0.98 May Page 1 of 17
User Manual Navigator Software Monarch Instrument Rev 0.98 May 2006 Page 1 of 17 Contents 1. NAVIGATOR SOFTWARE 2. INSTALLATION 3. USING NAVIGATOR SOFTWARE 3.1 STARTING THE PROGRAM 3.2 SYSTEM SET UP 3.3
More informationRTMS - Software Setup
RTMS - Software Setup These instructions are for setting up the RTMS (Robot Tracking & Management System) software. This software will run on your PC/MAC and will be used for various labs in order to allow
More informationPart Number Density Product Type Operation Temperature. W25Q80NESNIG 8Mb 1.2V Serial NOR Flash Memory Industrial (-40 C to +85 C)
1. INTRODUCTION This describes how to use the. The mbed enabled MCU board, which has an Arduino UNO R3 compatible terminal, is used in this description. 2. GENERAL DESCRIPTION The from Winbond Electronics
More informationUpgrading and Networking SK 7
Step 1 : Upgrading and Networking SK 7 Open the email with the link for upgrading to Servant Keeper 7. Click on the link and select Run. This will begin the upgrade process. NOTE: If you are running Version
More informationFirmware install with Windows XP
Firmware install with Windows XP Step 1. Go to our website www.midnitesolar.com and Left Click on Firmware. Step 2. Left Click on Download Firmware. Step 3. Read the Notes in red first and then Left Click
More informationElektor Uno R4 Installation & Test
Elektor Uno R4 Installation & Test Prerequisites Elektor Uno R4 USB-A to micro-b cable Computer with Windows (XP or later), Linux or OSX (10.7 or later) Arduino IDE 1.6.7 or higher (not 1.6.8) We highly
More informationInstructions for Installing FlashUpdate and Downloading Updates for Super Buddy Satellite Meter
Instructions for Installing FlashUpdate and Downloading Updates for Super Buddy Satellite Meter Updates to the Field Guide and to the instrument firmware are available from the Applied Instruments website.
More informationUser Guide for ID-e Tag List Feature
User Guide for ID-e Tag List Feature Version 2.0 Date: July 8th,2011 Tag function guide How to Tag create upload your Banned Customer list on the ID-e Reader General Description This Manual will explain
More informationGetting Started with Energia for MSP432 LaunchPad
May 9, 2018 Getting Started with Energia for MSP432 LaunchPad This tutorial is intended for installing and getting started with Energia for Texas Instrument SimpleLink MSP432P401R LaunchPad development
More informationBASIC MARLIN FIRMWARE CONFIGURATION USER GUIDE FOR THE SMARTRAP 3D PRINTER WITH LCD
INTRODUCTION: This is a basic user guide on how to verify and/or modify the settings in the Marlin firmware for use with the RepRap SmartRap 3D printer. There are several settings not covered in this manual
More informationTradeGuider VSA Plug-in for NinjaTrader quick install and setup guide.
TradeGuider VSA Plug-in for NinjaTrader quick install and setup guide. Introduction. This short guide will help you to download and install the TradeGuider VSA Plug-in for the NinjaTrader platform. This
More informationArduino WiFi Shield. Quick Start. Tinyos 2012 Version 1.0
Arduino WiFi Shield Quick Start Tinyos Electronics @ 2012 Version 1.0 Here is a Tinyos WiFi Shield tutorial. In this tutorial we will show you how to use the software to set the configuration of your WiFi
More informationRST INSTRUMENTS LTD.
RST INSTRUMENTS LTD. VW0420 Analog VW Interface Instruction Manual Ltd. 11545 Kingston St Maple Ridge, BC Canada V2X 0Z5 Tel: (604) 540-1100 Fax: (604) 540-1005 Email: Info@rstinstruments.com i VW0420
More informationRedBoard Hookup Guide
Page 1 of 11 RedBoard Hookup Guide CONTRIBUTORS: JIMB0 Introduction The Redboard is an Arduino-compatible development platform that enables quick-and-easy project prototyping. It can interact with real-world
More informationSetting up the PC ready for BESA 11
Setting up the PC ready for BESA 11 1 - Installing Driver. Important Note: Before you start to install the driver, please do not plug BESA 11 into the computer s USB port or else the installation will
More informationQuickstart CHAPTER 1. Powering Up. Installing the Software
CHAPTER 1 Quickstart THIS IS A CHAPTER for the impatient Evil Genius. Your new Arduino board has arrived and you are eager to have it do something. So, without further ado... Powering Up When you buy an
More informationScratch 2.0 Wireless Programming Guide for Vortex
Scratch 2.0 Wireless Programming Guide for Vortex DF4Scratch Service Vortex is a programmable robot developed by DFRobot. Based on the Arduino developing platform, Vortex is equipped with Atmega328 Arduino
More informationtune2air WMA1000 Firmware Upgrade Instruction 2013 Triamp Technology Ltd.
tune2air WMA1000 Firmware Upgrade Instruction 2013 Triamp Technology Ltd. www.viseeo.com A. Preparation before upgrading your firmware You will need to prepare: 1. A 30 pin ipod cable which comes with
More informationPredator Revision Update Instructions PREP:
Predator Revision Update Instructions (for Trinity, please see Trinity Update Instructions): PREP: You Need USB/Serial Cable and Power Source #U7778 OR Serial/Serial Cable and Power Source #U7777 (For
More informationSeeMeCNC Guides. RAMBo Control Firmware. This guide will show you how to install the firmware on your SeeMeCNC 3D printer.
SeeMeCNC Guides RAMBo Control Firmware This guide will show you how to install the firmware on your SeeMeCNC 3D printer. Written By: geneb 2018 seemecnc.dozuki.com/ Page 1 of 10 Step 1 Download and Install
More informationTech Memo # Software Engineering. Normal PRIORITY: DATE: April 17 th, 2015
Software Engineering Tech Memo #15-0001 PRIORITY: Normal DATE: April 17 th, 2015 TITLE: PRODUCTS AFFECTED: TOOLS REQUIRED: NOTE: INTRODUCTION: How to install and configure Adaptive Sign Server on a Windows
More informationArduino IDE Friday, 26 October 2018
Arduino IDE Friday, 26 October 2018 12:38 PM Looking Under The Hood Of The Arduino IDE FIND THE ARDUINO IDE DOWNLOAD First, jump on the internet with your favorite browser, and navigate to www.arduino.cc.
More informationRobotics Adventure Book Scouter manual STEM 1
Robotics Robotics Adventure Book Scouter Manual Robotics Adventure Book Scouter manual STEM 1 A word with our Scouters: This activity is designed around a space exploration theme. Your Scouts will learn
More informationHow to use the Zduino LEE Module with the Trainer Board
How to use the Zduino LEE Module with the Trainer Board Note: If you are going to use the Arduino/Zduino module for this distance training workshop, please download the Arduino software: 1. Connections
More informationTS1 Firmware Update Tool (for PC)
TS1 Firmware Update Tool (for PC) Installation and Operation Quick Start May 1, 2012 Overview This document provides instructions for using the Firmware Update Tool to update a TS1 Keypad to the latest
More informationMMI6070 Quick Start Guide
MMI6070 Quick Start Guide Introduction If at any time more information is required on HMI safety and protection ratings, HMI Power, and HMI communication, please refer to the MMI6070 Installation Guide
More informationPC Spa Dashboard Control User Guide
EL/GL Series - Mach 3 PC Spa Dashboard Control User Guide 900854 balboa-instruments.com Page 1 Page 2 PC SPA DASHBOARD The PC Spa Dashboard can be used with the EL8000, EL2000, EL1000 and GL systems. System
More informationELECTRONIC REMITTANCE ADVICE
ELECTRONIC REMITTANCE ADVICE INFORMATION ABOUT ERAS (ELECTRONIC REMITTANCE ADVICE) FILES Did you recently receive a check without a paper EOB? If so, the insurance company is sending you an Electronic
More informationSerial Interface. Upgrading Firmware
Thermok User s Manual The Thermok is four channel, K-type thermocouple display with LCD display and serial port. It can simultaneous display all four thermocouple channels, and at the press of a button,
More informationAgilent MassHunter Workstation Software Offline Qualitative and Quantitative Analysis
Agilent MassHunter Workstation Software Offline Qualitative and Quantitative Analysis Installation Guide Step 1. Remove Older Versions of MassHunter and Microsoft Excel Software 2 Step 2. Install Microsoft
More informationLogic Controls LV3000 USB Connected Virtual Pole Display on Windows Embedded, Vista, 7
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Logic Controls LV3000 USB Connected Virtual Pole Display on
More informationIBM iaccess (Java) Setup Guide for Foxtrot RPA
IBM iaccess (Java) Setup Guide for Foxtrot RPA Revised 03/31/17 Setup Steps - IBM iaccess is a Java application which requires these specific setup steps before it can be automated using Foxtrot RPA: 1.
More informationFPGA RGB Matrix. Created by lady ada. Last updated on :15:42 PM UTC
FPGA RGB Matrix Created by lady ada Last updated on 2017-12-27 09:15:42 PM UTC Guide Contents Guide Contents Overview Controlling the Adafruit 32x16 RGB LED Matrix with a DE0-Nano FPGA Board Prerequisites
More informationInstructions for MX350 Firmware Upload
Instructions for MX350 Firmware Upload MX350 Document AN10048 Page 1 of 39 Contents Section Description Page 1 Requirements 3 2 Install MX350 Setup Software 3 3 Download MX350 Firmware 4 4 Connect MX350
More informationEEG 101L INTRODUCTION TO ENGINEERING EXPERIENCE
EEG 101L INTRODUCTION TO ENGINEERING EXPERIENCE LABORATORY 1: INTRODUCTION TO ARDUINO IDE AND PROGRAMMING DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING UNIVERSITY OF NEVADA, LAS VEGAS 1. FYS KIT COMPONENTS
More informationStoring Your Exercise Files
Storing Your Exercise Files This appendix contains an overview for using this book with various file storage media, such as a USB flash drive or hard drive. Detailed instructions for downloading and unzipping
More informationTemperature-Humidity Sensor Configuration Tool Rev. A 1/25/
Rev. A 1/25/213 172 Contents Contents Temperature-Humidity Sensor Configuration Tool... 3 Read Sensor Screen... 3 Manual Calibration Screen... 4 Register View Screen... 5 Modbus Registers... 6 Reprogram
More informationNavigator Update to Software Instructions TABLE OF CONTENTS SECTION 1 DOWNLOAD FILES... 2 SECTION 2 UPDATE BOX SOFTWARE...
TABLE OF CONTENTS SECTION 1 DOWNLOAD FILES... 2 SECTION 2 UPDATE BOX SOFTWARE... 3-4 SECTION 3 INSTALL 1.05.01 SOFTWARE... 5 SECTION 4 IMPORT ALL PATTERNS... 6 1 Section 1 Download Files: Go to www.innovalongarm.com.
More informationBatch Eligibility Long Term Care claims
DXC Technology Provider Electronic Solutions software lets Connecticut Medical Assistance Program providers verify patient s eligibility and submit and correct claims for services all electronically. The
More informationInstalling your TC1 Processing Earthquake Data With AmaSeis and WinQuake
Installing your TC1 Processing Earthquake Data With AmaSeis and WinQuake By Linda and Ted Channel Edited: Dr Caroline Neuberg Contents List of figures... 3 Step 1. Assembly instructions for TC1... 4 Step
More informationTransmitter Programming Software Installation Instructions
Transmitter Programming Software Installation Instructions SERIES 5900 Temperature Transmitter The SERIES 5900 temperature transmitter from Watlow offers remarkably accurate temperature measurement and
More informationUSB/PPI+ Programming Cable Driver Procedure. Setting Guideline
USB/PPI+ Programming Cable Driver Procedure Setting Guideline Introduction 2 Functions....4 System requirement. 5 The setting of driver procedure. 6 The deletion of driver procedure.10 How to change COM
More informationUsing the Media Server Administrator (MSA) Interface for the Hardware Media Server
Using the Administrator (MSA) Interface for the Hardware Release 8.5 Revised: September 19, 2011 8:25 pm About the Administrator (MSA) Interface for the Hardware, page 1 Signing In to the Administrator
More informationSherlock Tutorial Getting Started
Sherlock Tutorial Getting Started Background Sherlock is a Java-based application that allows users to analyze the reliability of circuit card assemblies based on their design files. Sherlock has been
More informationSetting up FT3000 and version on Windows 7. This is a step by step guide for setting up the FT3000 on a new Windows 7 or 8 PC
Setting up FT3000 and version 3.0.1 on Windows 7 This is a step by step guide for setting up the FT3000 on a new Windows 7 or 8 PC PROBLEM: Computer being updated from XP to WIN 7 or 8. New PC does not
More informationLex Talus Corporation
Lex Talus Corporation 109 East 17th Street, Suite 80 Cheyenne, WY 82001 Tel: (775) 434.0420 To: Subject: Nomad Purchaser FAQ The first thing you must do with your new Nomad is to calibrate the battery.
More informationTroubleshooting. Note. SC485, USB485 and USB485B. Table of Contents.
SC485, USB485 and USB485B Troubleshooting Note www.lightorama.com Use this document if: 1. You want to locate the Windows communications port name being used by the RS485 adapter. 2. You believe the USB
More informationInstalling the Ampire UART TFT
Installing the Ampire UART TFT Thank you for Purchasing this UART TFT Kit from IES. The setup of the device is broken down into 4 stages which should be carried out IN THE FOLLOWING ORDER for correct operation
More informationVerifone MX800 Series Pinpad Serial Installation
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Verifone MX800 Series Pinpad Serial Installation Note: No drivers
More informationDairyPlan Interface Setup Index. 3. Gateway Setup (VC3/4 equipment)
DairyPlan C21 DairyPlan Interface Setup Index Page no. 3. Gateway Setup (VC3/4 equipment) 11. Multi-Port Setup using Win 7 25. Multi-Port Setup using Win Vista 33. Multi-Port Setup using Win XP 51. Multi-Port
More informationDesigned & Developed By: Ms. Jasleen Kaur, PhD Scholar, CSE. Computer Science & Engineering Department
Design & Development of IOT application using Intel based Galileo Gen2 board A Practical Approach (Experimental Manual For B.Tech & M.Tech Students) For SoC and Embedded systems in association with Intel
More information22080 IoT2 Appendix B: Get Started with Arduino IDE & ExpLoRer
Contents Purpose... 1 Requirements... 1 Objectives... 2 Procedure... 2 Step 1. Download and Install the Arduino IDE v1.8.5... 2 Step 2. Configure the Sketchbook Location, Board Manager URL & Other Preferences...
More informationPixel Software/Firmware Update Instructions
1 Loading Software on to USB Flash Drive 1. The latest Pixel software can be downloaded from the Elevator Controls website (elevatorcontrols.com/downloads/download) a user name and password is required.
More informationAN-77XX-XP 2K MCS77XX. Windows-2k & Windows-xp
AN-77XX-XP 2K MCS77XX 18 th Feb 2004 i All information in this document is believed to be accurate as of the date published. All brands or product names are the property of their respective holders. MosChip
More informationAVTECH. Voice Modem w/usb. Installation Note
AVTECH Voice Modem w/usb AVTECH s Voice Modem connects Device ManageR s host system to an analog phone line. With Device ManageR s Dial Out Plugin Bundle, this modem allows you to dial a phone directly
More informationUNic Eclipse Mini Tutorial (Updated 06/09/2012) Prepared by Harald Gjermundrod
Page 1 of 19 UNic Eclipse Mini Tutorial (Updated 06/09/2012) Prepared By: Harald Gjermundrod Table of Contents 1 EASY INSTALLATION... 2 1.1 DOWNLOAD... 2 1.2 INSTALLING... 2 2 CUSTOMIZED INSTALLATION...
More informationsbdconfig.exe Software
Installing the Please Note: The software only works with the 3200 or 3300 digital clocks series. Sapling s USB to RS485 converter needs to be purchased separately. Other USB to RS485 converters will not
More informationINSIGHT Installation Instructions
This is the New Icon that will appear on your computer screen after the INSIGHT v8.1 software is installed. IMPORTANT: These instructions pertain to version 8.1.29. INSIGHT v8.1.29 requires Windows 8,
More informationA.1 MD-CC USB to SPI communications
A.1 MD-CC305-001 USB to SPI communications The MD-CC305-001 is an interface cable which combines Power, Logic and communications with an inline USB to SPI converter. It is recommended with the first purchase.
More informationCastlerock / Network CFS Installation & General Procedures
Castlerock / Network CFS Installation & General Procedures Richardson Electronics 12975 16 th Ave. N. Suite 300 Plymouth, MN 55441 USA www.imagesystemscorp.com Castlerock-Network CFS install 1 Contents
More informationkeyestudio Keyestudio MEGA 2560 R3 Board
Keyestudio MEGA 2560 R3 Board Introduction: Keyestudio Mega 2560 R3 is a microcontroller board based on the ATMEGA2560-16AU, fully compatible with ARDUINO MEGA 2560 REV3. It has 54 digital input/output
More informationDRIVERS INSTALLATION GUIDE
USB INTERFACE DRIVERS INSTALLATION GUIDE * These CIU-2 drivers are for windowsvista/xp/2000 use, and is not compatible with other OS. Downloaded ZIP extraction (decompression)...p2 Extraction (decompression)
More informationAssigning COM Port Numbers to the Serial Ports of a USBto-Serial
Assigning COM Port Numbers to the Serial Ports of a USBto-Serial Adapter A Technical Application Note from Doppler Systems May 6, 2008 1.0 Introduction USB-to-serial converters have an interesting and
More informationArduino IDE The Developer Kit library The JeeLib library for RFM12 transceivers
SKU: 810011 The aim of this project is to build a hydrogen powered remote temperature sensor. It is based on the Arduino, Developer Kit fuel cell shield, Maxim DS18B20 1 Wire temperature sensor, and the
More informationMagicSoft Version 3.02
MagicSoft Version 3.02 Chapter 1 Introduction MagicSoft is designed to be intuitive and easy to navigate. You ll never find yourself buried deep in a menu without quick access to the screens and tools
More informationDriver Installation. Getting Started for Windows user (Setting up your Robot)
Getting Started for Windows user (Setting up your Robot) Get the drivers and download the software to make your robots go! Programmer Driver Arduino Software IDE Ringo & Wink Software Libraries Driver
More informationAD4430A USB Connection Instructions
Connecting AD4430A to PC by USB cable Device Installation ❷ Turn on power of the AD4430A and connect the USB cable A software installation message will appear shortly as shown below USB Cable PC Side USBA
More information1 / 20. User Manual. Getting started with devention DfuSe USB upgrade tool
1 / 20 User Manual Getting started with devention DfuSe USB upgrade tool 2 / 20 1. Contents 2. Introduction... 3 3. System requirements... 4 4. Package contents... 5 5. How to enter program update interface...
More informationEB020 Installation Instructions.
EB020 Installation Instructions. Detailed below are the 3 steps needed to get up and running with the CPLD board. This 3 step process needs to be completed only once and then the drivers should all be
More informationUG MCAP II & ecap II Smartware & USB Drivers Installation
MCAP II & ecap II Smartware & USB Drivers Installation Sept 4, 2008 Copyright 2008 by QEI Inc. ALL RIGHTS RESERVED NOTICE The information in this document has been carefully checked and is believed to
More informationAbout SunFounder Preface SunFounder is a technology company focused on Raspberry Pi and Arduino open source community development. Committed to the pr
About r Preface r is a technology company focused on Raspberry Pi and Arduino open source community development. Committed to the promotion of open source culture, we strive to bring the fun of electronics
More informationTelonics Data Converter - USB Device Software and Driver Installation
TELEMETRY-ELECTRONICS CONSULTANTS 932 E. IMPALA AVENUE MESA, ARIZONA 85204-6699 U.S.A. TEL (480) 892-4444 FAX (480) 892-9139 E-MAIL info@telonics.com www.telonics.com Telonics Data Converter - USB Device
More information3.1 I-7560 Pin Assignment and Specifications: Introduction
3.1 I-7560 Pin Assignment and Specifications: Introduction The I-7560 adds a Windows serial Com port via its USB connection and is compatible with new & legacy RS-232 devices. USB Plug and Play allows
More information- MANUAL FOR PC CONNECTION -
- MANUAL FOR PC CONNECTION - [STEP 1 : Software Requirements] To upload/download the channel plans or upload the stored file(s), you need both CP2102 USB to UART Bridge Controller driver and HyperTerminal
More informationFSU Inventory Scanner Set up & Use for Windows PC
FSU Inventory Scanner Set up & Use for Windows PC FSU Inventory Scanner kit: 1 FSU Property Scanner (Model: CipherLab 8100) 1 Scanner Cradle 1 Scanner Cradle Power Supply 1 USB Cradle to PC Connector Cable
More informationLab 1: Arduino Basics. Rodrigo Carbajales and Marco Zennaro ICTP Trieste-Italy
Lab 1: Arduino Basics Rodrigo Carbajales and Marco Zennaro ICTP Trieste-Italy Step Zero Clean up your desks! :) Goals of this Lab Learn how the programming takes place Excercises about: installing the
More informationUsing your Brady Printer connected to your PC.
Using your Brady Printer connected to your PC. While the IDXPERT Thermal Labeling System is sold as a standalone printer, it can also be used connected to your PC using optional Labelmark Software. This
More informationTable of Contents.
Table of Contents http://www.advancedactuators.com 1. Items Included with the ThumbLock PCMU:... 2 2. IMPORTANT NOTE:... 2 3. Supported Operating Systems:... 2 Section 1 Installing the ThumbLock PCMU Software...
More information1 / 14. User Manual. Getting started with UP02 program upgrade tool
1 / 14 User Manual Getting started with UP02 program upgrade tool 2 / 14 1. Contents 1. Contents... 2 2. Introduction... 3 3. System requirements... 4 4. Package contents... 5 5 The installation of UP02
More informationTest Procedure for the NCV7748GEVB Evaluation Board
Test Procedure for the NCV7748GEVB Evaluation Board 1) Place the DEMO MODE switch OFF (left). 2) Populate all jumpers except the LOOP jumper next to the OUTPUT CONTROL push-button. 3) Plug the 12V (1.0A)
More information