E5070B/E5071B Adjustment Program. <Agilent Service Center Use Only> Operation Manual. First Edition. Agilent Part No.

Transcription

1 E5070B/E5071B Adjustment Program <> Operation Manual First Edition Agilent Part No. N/A October 2002 Printed in Japan

2 Notices The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of the Agilent Technologies. Agilent Technologies Japan, Ltd. Componet Test PGU Kobe 1-3-2, Murotani, Nishi-Ku, Kobe-shi, Hyogo, Japan Copyright Agilent Technologies Japan, Ltd Manual Printing History The manual s printing date and part number indicate its current edition. The printing date changes when a new edition is printed. (Minor corrections and updates that are incorporated at reprint do not cause the date to change.) The manual part number changes when extensive technical changes are incorporated. October 2002 First Edition 2

3 Contents 1. Installation Warm-up for Performance Test Required Equipment Preparation for using the Adjustment Program Required Controller Installing a GPIB Card (82341C/D or 82350A) Installing Agilent VEE for Personal Computer Installing Adjustment Program into Your PC Equipment Setup Setting Talker/Listener GPIB address of the E5070B/E5071B Registering Power Sensor Calibration Data Operation How to perform the E5070B/E5071B Adjustment Program Main Window Information Model Number Serial Number Option Adjustment Name Result Summary

4 Contents 4

5 1 Installation This chapter provides information for the installation of E5070B/E5071B adjustment program. 5

6 Installation Warm-up for Performance Test Warm-up for Performance Test Allow the E5070B/E5071B to warm up for at least 30 minutes before you execute any of the adjustments. Required Equipment The required test equipment for the adjustments is listed in Table 1-1. Use only calibrated equipment when adjusting the E5070B/E5071B. 6 Chapter 1

7 Installation Required Equipment Table 1-1 Recommended Equipment Equipment Critical specifications Recommended Model Qty. Frequency Counter Frequency Standard Frequency: 1 MHz to 3 GHz Accuracy: < 2.5 ppm Frequency: 10 MHz, Time Base Error: /year 53131/32A Opt.010 & 030 *1 1 or 53181A Opt.010 & 030 *2 5071A 1 Power Meter No Substitute E4419A/B 1 Power Sensor No Substitute 8482A E4412A 1 1 Calibration Kit No Substitute 85032F 1 Fixed Attenuator (6dB) 50 9, N(m)-N(f), VSWR A Opt.006,H60 1 Cable BNC(m)-BNC(m) Cable, 61 cm p/n Coaxial Cable with Type-N(m) connectors, 61 cm (24 in) N6314A ( p/n ) 1 Adapter N(m)-BNC(f) Adapter p/n Torque Wrench Size: 3/4 inch Torque: 136 N-cm p/n *1.Opt.050 and Opt.124 can be substituted for Opt.30. In this case, a N(m)-BNC(f) adapter is necessary. *2.Opt.050 and Opt.124 can be substituted for Opt.030. In this case, a N(m)-BNC(f) adapter is necessary. Chapter 1 7

8 Installation Preparation for using the Adjustment Program Preparation for using the Adjustment Program To use the Adjustment Program, some preparation is required. This section describes how to proceed. Required Controller The following controller system is required to run the performance test program. Windows PC PC-AT Compatible, RAM: 64MBytes, CPU Pentium 200 MHz or faster, HDD: 10 Mbytes or move free space OS Microsoft Windows NT (4.0), Windows 95, Windows 98, Windows 2000 Software GPIB Card Agilent VEE (Rev 5.0x or 6.0x) 82350A, 82340B, 82341C/D Installing a GPIB Card (82341C/D or 82350A) Install a GPIB Card into your computer (see the GPIB Card manuals). The select code of the GPIB Card should be set to 7. Installing Agilent VEE for Personal Computer Install the Agilent VEE (Rev 5.0x or 6.0x) into your computer (see the Agilent VEE manuals). Installing Adjustment Program into Your PC Step 1. Make a copy of the E5070B/E5071B adjustment program named ADJE507071B.EXE in a directory of the hard disk drive in your PC. Step 2. Double-click on the filename on the Windows Explorer to start extracting the self-extracting achieve. Step 3. You will be prompted to enter folder name for installing the program files. Enter the folder name, then click on UNZIP. The default folder is C:\ADJE507071B Figure 1-1 Prompt of Self-extracting Achieve Step 4. Confirm the message that you have successfully extracted the files and click OK and 8 Chapter 1

9 Installation Preparation for using the Adjustment Program Close. Figure 1-2 Message Window Chapter 1 9

10 Installation Preparation for using the Adjustment Program Equipment Setup Performing adjustments requires the system described in this section. The Hardware Setup is shown in Figure 1-3. Figure 1-3 Adjustment Hardware Setup Setting Talker/Listener GPIB address of the E5070B/E5071B To control the E5070B/E5071B in the adjustment program, the talker/listener GPIB address must be set. Check and set the GPIB address according to the following procedure. Step 1. Press - Misc Setup - GPIB Setup - Talker/Listener Address. If the address 17 has not been set, proceed to the next step. Step 2. Enter the GPIB address 17 using the ENTRY block keys on the front panel. Registering Power Sensor Calibration Data The calibration data of the 8482A power sensor must be registered before running the adjustment program. Execute the Agilent EditCal Calibration Factor Editor to register it. Step 1. Start the EditCal to click on Start button, Programs and Agilent EditCal on Windows. Step 2. The top window appears as shown in Figure 1-4. Choose Calibration Data, then press Start. 10 Chapter 1

11 Installation Preparation for using the Adjustment Program Figure 1-4 EditCal Top Window Step 3. The calibration data menu appears as shown in Figure 1-5. Choose 8482A and the serial number to edit, then click on Edit. If the serial number is not registered, Click on Add and choose 8482A. Figure 1-5 Calibration Data Menu Step 4. The 8482A calibration data window appears as shown in Figure 1-6. Input the following items and click on OK. Serial number (for addition) Calibration Date Calibration Due Date Calibration Data NOTE Delete the calibration points which are not described on the calibration report because the adjustment program interpolates the calibration factor for the frequency which calibration factor is not registered. Chapter 1 11

12 Installation Preparation for using the Adjustment Program Figure A Calibration Data Window 12 Chapter 1

13 2 Operation This chapter provides information for using the E5070B/E5071B adjustment program. 13

14 Operation How to perform the E5070B/E5071B Adjustment Program How to perform the E5070B/E5071B Adjustment Program Step 1. Start the Agilent VEE (Rev 5.0x or 6.0x). Step 2. Load the adjustment program file into the Agilent VEE as follows. 1. Pull down the File menu from the Agilent VEE window and select Open. 2. Navigate to the folder that the program installed, then choose ADJE507071B.VEE and click Open. Step 3. You may be asked to add drivers for the equipment during the program loading. Click on OK and the GPIB address for each equipment. Enter 0 as the address for each equipment which is not used for the adjustment. (See Figure 2-1). Figure 2-1 Direct I/O configuration Step 4. The main window appears as shown in Figure 2-2. Click on START button to proceed. Figure 2-2 Main Window Step 5. The ETE Configuration window menu appears as shown in Figure 2-3. Input all columns 14 Chapter 2

15 Operation How to perform the E5070B/E5071B Adjustment Program and click on Next. NOTE Figure 2-3 The Home Directory means the directory where ADJE507071B.VEE is stored. ETE Configuration Window Step 6. The Emvironment window appears as shown in Figure 2-4. Input the data and click on NEXT STEP. Chapter 2 15

16 Operation How to perform the E5070B/E5071B Adjustment Program Figure 2-4 Environment Information Window Step 7. The main menu appears as shown in Figure 2-5. The description of the button on the window is described in Table 2-1. Figure 2-5 Main Menu Table 2-1 Description of Menu Buttons Item All Adjustment Spot Adjustment Description Performs all adjustment items. After pushing this button, the program checks connection of ETE and start adjustment. Performs a part of adjustment items according to the replaced assembly. After pushing this button, the program proceed to Step Chapter 2

17 Operation How to perform the E5070B/E5071B Adjustment Program Table 2-1 Description of Menu Buttons Item Input Environment Data Program End Description Show the environment Information window. After this button, the program proceeds to Step 6. Quits the adjustment program. Step 8. The spot adjustment menu appears as shown in Figure 2-6 when you pushing Spot Adjustment. After clicking on a button, The adjustment items is performed according to the replaced assembly. Refer to Table 2-2 for detail. NOTE Figure 2-6 Execute "All Adjustment if two or more spot adjustment items are selected. Spot Adjustment Window Chapter 2 17

18 Operation How to perform the E5070B/E5071B Adjustment Program Table 2-2 Required Adjustment Item Select Button Adjustment Item Initialize Correction Constants Writing ID Frequency Reference Adjustment Oven Reference Adjustment (Opt. 1E5) IF Range Gain/Phase Adjustment Source Power Adjustment Test Ports Characteristics Adjustment Storing Correction Constants Checking Correction Constants All Adjustment Spot Adjustment: Source Board Spot Adjustment: Receiver (RF) Board Spot Adjustment: Receiver (IF) Board Spot Adjustment: RF Switch Spot Adjustment: Crystal Oven (for 1E5) Spot Adjustment: Att (for 214/314/414) Spot Adjustment: Hard Disk Drive Spot Adjustment: Analog Interface Spot Adjustment: Level Vernier Spot Adjustment: Power Amp Module 18 Chapter 2

19 Operation Main Window Information Main Window Information Figure 2-7 shows the displayed information. Figure 2-7 Displayed Information in Main Window Model Number The model number of the equipment to be adjusted. Serial Number The serial number of the equipment to be adjusted. Option The installed option in the equipment to be adjusted. Adjustment Name The adjustment executed now. Result Summary Table 2-3 This area shows the summary of the results. The information displayed in each column is described in Table 2-3. Column in Test Result Summary Column ADJUSTMENT NAME Description Name of Adjustment JUDGE Result of Adjustment. O means pass. X means fail. - means not performed. DATE TIME Time when Adjustment is finished. Chapter 2 19