ProcessLogix R510.0 Server Installation Instructions

Transcription

1 ProcessLogix R510.0 Server Installation Instructions Installation Instructions Before you begin... This publication guides you through the remaining processes required to initialize a ProcessLogix Server. You are required to finalize the Server installation by completing the instructions outlined in this document. This document does not contain complete instructions covering the installation process, and refers you to procedures contained in other documentation. For a successful installation, have the following documents available: ControlNet PCI Communication Interface Card Installation Instructions, publication 1784-IN003, shipped with the 1784-PCIC card. ProcessLogix R510.0 Installation and Upgrade Guide (I&UG), publication 1757-IN510, shipped with the ProcessLogix R510.0 Software Kit. These and other ProcessLogix documents can be found on The Automation Bookstore, at The following table lists items that you MUST complete before attempting to use the ProcessLogix Server. If you have a redundant Server pair, you must complete these items on both SERVERA and SERVERB. Item Page Installing the 1784-PCIC Card 3 Installing the Windows 2000 license and Warranty Transfer 3 Logging on to Windows Configuring the 1784-PCIC Card 4 Changing the PC Name 5 Changing the Network Settings 5 Creating an Emergency Repair Disk 7 Installing the RSLinx Activation File 7 Changing the ProcessLogix License 8 Configuring RSLinx Drivers for ControlNet Supervisory Network 10

2 2 ProcessLogix R510.0 Server Installation Instructions Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-1.1 available from your local Rockwell Automation sales office or online at describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited. Throughout this manual, when necessary, we use notes to make you aware of safety considerations. WARNING! ATTENTION! Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which may lead to personal injury or death, property damage, or economic loss. Identifies information that is critical for successful application and understanding of the product. Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you to identify a hazard, avoid a hazard, and recognize the consequences. SHOCK HAZARD Labels may be located on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present. BURN HAZARD Labels may be located on or inside the equipment, for example, a drive or motor, to alert people that surfaces may be dangerous temperatures.

3 ProcessLogix R510.0 Server Installation Instructions 3 Installing the 1784-PCIC Card If you are using Ethernet for your Supervisory Network, skip to Installing the Windows 2000 license and Warranty Transfer on page 3. Before powering on the system, you must install the 1784-PCIC card. The 1784-PCIC is purchased separately from the ProcessLogix Server. Refer to the ControlNet PCI Communication Interface Card Installation Instructions for complete installation details. Installing the Windows 2000 license and Warranty Transfer 1. Turn on the computer. 2. Select I accept this agreement and click Next. 3. Verify the information on the Regional Settings window and click Next. 4. Enter the appropriate Name and Organization and click Next. 5. Enter your Windows 2000 Server Product Key and click Next. Windows Server 2003 licenses can be downgraded to use or access Windows 2000 Server. If you have a Windows 2003 Server license key on your PC, contact Dell Technical support at to request a Windows 2000 Server license key. 6. At the Date and Time Settings window: a. If necessary, adjust the Date and Time settings. b. Set the appropriate Time Zone for your location. c. Uncheck the Automatically adjust clock for daylight saving changes chekcbox. d. Click Next. ATTENTION! Failure to uncheck the automatic adjustment for daylight savings time checkbox will cause a redundant server pair to lose sync when the time is automatically adjusted. Choosing not to automatically adjust the time allows you to decide when to make the adjustment (at a time that is not critical to your process). 7. At the Windows 2000 Setup window, click Restart Now. If there is a delay clicking Restart Now, setup automatically restarts the PC.

4 4 ProcessLogix R510.0 Server Installation Instructions 8. In order to receive support from Dell, you must fill out their warranty transfer form. The U.S. Ownership Transfer Form is only available online at: The International Unit Location Transfer Form is only available online at: Logging on to Windows Press <Ctrl> + <Alt> + <Delete> to initiate Windows 2000 logon. 2. Enter >ps_user< as the User name. 3. Enter >Proce$$510< as the default password. TIP If you purchased a new ProcessLogix R510.0 Server from Rockwell Automation, the default passwords for ps_user and Administrator were set to Proce$$510 for security reasons. 4. Press <Enter> or click OK to complete the logon. TIP You must repeat the above steps every time you restart the Server. Configuring the 1784-PCIC Card If you are using Ethernet for your Supervisory Network, skip to Changing the PC Name, below. Refer to 1784-PCIC Driver and Installation and 1784-PCIC Firmware Installation in Chapter 7 of the R510.0 I&UG for details.

5 ProcessLogix R510.0 Server Installation Instructions 5 Changing the PC Name If you purchased a new ProcessLogix R510.0 Server from Rockwell Automation, the operating system and ProcessLogix software have already been installed. Once the ProcessLogix R510.0 software is installed, changing the computer name requires a full uninstall and reinstall of all the ProcessLogix R510.0 software. Refer to Changing the Computer Name on a ProcessLogix Server in Chapter 8 of the R510.0 I&UG. PC Naming Rules The Factory default PC Names are PLX1, PLX1A, or PLX1B. If you have more than 1 PC on the same network, you must make certain that the PC names and IP addresses are unique (i.e. PLX1, PLX2). The base name cannot contain more than 13 alphanumeric characters and must contain no spaces. The full computer name cannot contain more than 14 alphanumeric characters. The following naming conventions are required for given ProcessLogix system architectures. For non-redundant Server, be sure the name does not end in the letter A or B. The default name is PLX1. For redundant Servers, append a letter to the base name to identify the PC s function in the system architecture beginning with the letters A and B for the primary and secondary Servers, respectively. The default name for the primary Server (SERVERA), is PLX1A and the default name for the secondary Server (SERVERB) is PLX1B. (14 Character total: Up to 13 Base plus A or B) Changing the Network Settings 1. Click Start Settings Network and Dial-up Connections. 2. Right-click Local Area Connection and select Properties. 3. Select Internet Protocol (TCP/IP) and click Properties. 4. In the Internet Protocol (TCP/IP) Properties Window: a. Select the Use the following IP address option. b. Enter the appropriate IP address information.

6 6 ProcessLogix R510.0 Server Installation Instructions The following Private Networking IP Address scheme can be utilized for the system to operate: Table 1 Private Networking IP Address scheme Server Type Non-Redundant Server or Primary Redundant Server Suggested Private Networking IP Address NIC 1: NIC 2: NIC 3: Backup Redundant Server NIC 1: NIC 2: NIC 3: c. Enter the Subnet Mask d. Enter a default gateway if necessary. IP Addresses are critical to the communication of the system. Rockwell Automation suggests, when possible, to utilize a Private Network for the control system, not connected to any other networks. This isolates the control system from interference from any business communication. In some organizations it is important for these addresses to be controlled by the IT organization. Consult your company s practices and IT organization for the appropriate IP address information. It will be necessary to use valid IP information to integrate the ProcessLogix Control system with the Business Network. 5. Click OK.

7 ProcessLogix R510.0 Server Installation Instructions 7 Creating an Emergency Repair Disk 1. Insert a floppy disk into your PC. 2. Click Start Programs Accessories System Tools Backup. 3. Click Emergency Repair Disk. The Emergency Repair Diskette window opens. 4. Check the Also back up the registry to the repair directory checkbox and click OK. 5. When finished, click OK. Installing the RSLinx Activation File ATTENTION! Before attempting to move the activation file, you MUST exit all ProcessLogix applications and stop all ProcessLogix services. Before continuing, you must complete the procedure in Stopping ProcessLogix Applications and Services in Chapter 8 of the R510.0 IU&G. Your ProcessLogix Server is factory loaded with RSLinx Lite. To activate RSLinx OEM (necessary for full functionality of ProcessLogix): 1. Insert the RSLinx Master Disk into your PC. 2. Click Start Run. 3. Enter this path or Browse to: >A: (or your floppy drive letter)\evmove.exe< 4. Click OK to launch the move. 5. Verify that you are Moving Activations From Drive A:(or your floppy drive letter) To Drive C:(or your hard drive letter). 6. Click OK to initiate the move.

8 8 ProcessLogix R510.0 Server Installation Instructions 7. Click Move to move the file to the hard drive. 8. Wait for a dialog box to indicate a successful move, and click OK. 9. Remove the Master Disk and store it in a safe place. TIP If you need to reformat your computer s hard drive, you must first move the activation file back to this Master Disk using this same general procedure; otherwise, the file will be corrupted. Changing the ProcessLogix License The ProcessLogix Server is shipped with a temporary license. You must enter the system ID and authorization numbers from the supplied license certificate to activate the license options that you have ordered. To change the license: 1. Click Start Programs ProcessLogix Server Start-Stop ProcessLogix Server to call up the ProcessLogix Server dialog box. TIP To display the Full Mode version of the ProcessLogix Server dialog box, click the icon on the left of the title bar and click Advanced Full Mode. A checkmark appears in front of the Full Mode selection to show that it is active. 2. With Full Mode active, select the Database Only option. 3. Click Yes to confirm the action and wait for the Server to change its state.

9 ProcessLogix R510.0 Server Installation Instructions 9 4. Close the ProcessLogix Server dialog box. 5. Click Start Programs ProcessLogix Server Setup. 6. At the Welcome window, click Next. 7. Check the Change software license checkbox and click Next. 8. Enter the new System and Authorization numbers and click Next. 9. Click Next to confirm. 10. If the license includes a new database size, click Yes in the Rebuild Database dialog box. 11. When completed, uncheck the Start ProcessLogix Server checkbox and click Finish. 12. Restart the computer. To verify your license: 1. Click Start Programs ProcessLogix Server Setup. 2. At the Welcome window, click Next. 3. Check the View software license details checkbox and click Next. 4. If there is a discrepancy between the ordered options and the options displayed, call Rockwell Automation Technical Support at (440)

10 10 ProcessLogix R510.0 Server Installation Instructions Configuring RSLinx Drivers for ControlNet Supervisory Network Complete the following steps to configure the ControlNet PCIC drivers for RSLinx. If you are using Ethernet for your Supervisory Network, skip to Configuring RSLinx Drivers for Ethernet Supervisory Network in Chapter 3 of the R510.0 I&UG. 1. Click Start Programs Rockwell Software RSLinx RSLinx to call up the Rockwell Software RSLinx window. 2. Click Communications Configure Drivers to call up the Configure Drivers dialog box. 3. Select 1784-PCIC(S) for ControlNet devices in the Available Drivers drop-down list and click Add New to call up the Add New RSLinx Driver dialog box. 4. Click OK to accept the default name AB_PCIC-1 for the driver. The driver name MUST be AB_PCIC-1.

11 ProcessLogix R510.0 Server Installation Instructions In the Configure 1784-PCIC window, enter the following: a. Serial Number(hex): This value is read from the PCIC card and does not change. b. Network Address(dec): Change the default of 99 to: Non-redundant Server 24 Redundant Server A 24 Redundant Server B Click OK to start the PCIC driver. 7. In the Configure Drivers dialog box, you should see AB_PCIC-1 listed in the Configured Drivers list with the status Running. If the AB_PCIC-1 driver status is not Running, call Rockwell Automation Technical Support. 8. Click Close to close the Configure Drivers dialog box. 9. Close RSLinx. 10. Restart the PC. Whenever the 1784-PCIC driver has been updated or the Network Address is changed, the 1784-PCIC driver must be stopped and restarted to complete the change. You must power down the PC. ProcessLogix, ControlNet, and Allen-Bradley are trademarks of Rockwell Automation, Inc. Windows 2000 is a registered trademark of the Microsoft Corporation. Dell is a registered trademark of the Dell Computer Corporation. RSLinx is a trademark of Rockwell Software, Inc.

12 Rockwell Automation Support Rockwell Automation provides technical information on the web to assist you in using its products. At you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnect Support programs. For more information, contact your local distributor or Rockwell Automation representative, or visit New Product Satisfaction Return Rockwell tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned: United States Outside United States Contact your distributor. You must provide a Customer Support case number (see phone number above to obtain one) to your distributor in order to complete the return process. Please contact your local Rockwell Automation representative for return procedure. PN Supersedes Publication 1757-IN951A-EN-P - October 2003 Copyright 2006 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.