AEE MAKERSPACE: TROUBLESHOOTING 101
|
|
- Osborne Terry
- 5 years ago
- Views:
Transcription
1 AEE MAKERSPACE: TROUBLESHOOTING 101 DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING MICHIGAN STATE UNIVERSITY I. TITLE: Lesson 02: Elenco M-2666K DC Testing and Calibration II. PURPOSE: This lab will show you how to do the DC voltage / current testing and calibration of the Elenco M-2666K DMM using the equipment in our AEE Makerspace (Room 2228 EB). This material is found in Section B of the Elenco Assembly and Instruction Manual. III. BACKGROUND MATERIAL: See Lesson 02 YouTube Video at: IV. EQUIPMENT REQUIRED: 1 HP 34401A Digital Multimeter 1 Agilent E3630A Triple Output Power Supply 1 Agilent E3611A DC Power Supply V. PARTS REQUIRED: 1 Elenco Model M-2666K DMM kit 2 Alligator clips 1 47 ks resistor 1
2 VI. LABORATORY PROCEDURE: A) DC Voltage Testing 1. Locate a lab station that looks like this: Figure 1: Lab test station 2. On page 15 of your Elenco Assembly and Instruction Manual is a procedure for testing and calibrating your meter for DC voltages. Configure the equipment as shown in Fig. 2 using banana-to-banana wires but do not turn on the equipment yet. Figure 2. DC voltage testing and calibration 2
3 3. Set the selector knob on the Elenco DMM to the 20 V DC position (meter section V next to a bar over 3 dots on the upper-right side) and connect the 9 V battery to run the meter. 4. Press the +20 V button on the bottom-left of the Agilent E3630A Triple Output Power Supply. Turn on the power. Adjust the ± 20 V knob on the upper-left to read about 10 V. 5. Turn on the power for the HP 34401A Digital Multimeter. The default setting is to measure DC voltage. 6. Follow the Voltage Test Procedure 4 on page 15 of your Elenco Assembly and Instruction Manual. 7. Repeat for setting the power supply to 15 V and 5 V. 8. Turn off the power for the Agilent E3630A Triple Output Power Supply. B) DC Low Current Testing 1. Configure the equipment as shown in Fig. 3 using banana-to-banana wires, 2 alligator clips and a 47 ks resistor but do not turn on the power supply. Figure 3. DC low current testing 3
4 2. Set the selector knob on the Elenco DMM to the 200 :A DC position (meter section A next to a bar over 3 dots on the lower-left side). 3. Press the blue shift button on the lower-right of HP 34401A Digital Multimeter and then press the DC V button. Above this button are the letters DC I. We have now changed the reading from voltage to current. 4. Turn on the power of power supply. It still should be set to 5 V. By Ohm s Law, the current flowing is approximately 5 V / 47 ks = 106 :A. Both meters should be reading this approximate value. Change the voltage to 9 V and the current will be around 191 :A. There are no adjustments here, just verification. 5. Pick a resistor and voltage setting using Ohm s Law to verify the other scales of 2 ma, 20 ma and 200 ma. Turn off the power supply. 6. We have just completed the first 3 steps of the Current Test found on page 15 of your Elenco Assembly and Instruction Manual. C) DC High Current Testing 1. Configure the equipment as shown in Fig. 4 using banana-to-banana wires. Note that we are now using the Agilent E3611A DC Power Supply. Do not turn on the power supply. Figure 4. Setting a constant current 4
5 2. The HP 34401A should still be set up to read current. (If not repeat part B-3.) 3. Turn selector knob on your Elenco DMM to the 20 A DC position (meter section A next to a bar over 3 dots on the lower-left side) 4. Check that the Range button is out of the Agilent E3611A DC Power Supply. Turn the knob labeled Voltage fully clockwise. Turn the knob labeled Current fully counter-clockwise. Turn on the power supply. 5. Rotate the Current knob clockwise and watch the current increase on the HP 34401A Digital Multimeter. It auto scales to give you the correct reading. (This meter sells for about $1000 and so has some advanced features.) 6. Under these conditions the power supply is acting as a constant current source. Adjust the current to read about 1.5 A on the HP 34401A Digital Multimeter. This is the most we can deliver with this power supply. 7. Follow the Current Test Procedure 20A Scale on page 15 of your Elenco Assembly and Instruction Manual to the end step number 5. For these tests use the value displayed on the HP 34401A Digital Multimeter as your exact current. 5
Agilent 3630A Triple DC Power Supply. Agilent 34401A Digital Multimeter (DMM)
Agilent E3630A Triple DC Power Supply and Agilent 34401A Digital Multimeter (DMM) Agilent 3630A Triple DC Power Supply The DC power supply used in this lab is the Agilent E3630A Triple DC power supply.
More informationEE 100 DMM and DC Power Supply LabVIEW Experiment Guide
1. Objectives EE 100 DMM and DC Power Supply LabVIEW Experiment Guide The purpose of this experiment is to show you how to interface your DMM and DC Power Supply to LabVIEW. I. World of LabVIEW LabVIEW
More informationELECTRONIC INSTRUMENTATION AND SYSTEMS LABORATORY
ELECTRONIC INSTRUMENTATION AND SYSTEMS LABORATORY DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING MICHIGAN STATE UNIVERSITY I. TITLE: Lab IX - Light Activated Exhaust Fan II. PURPOSE: One use of bipolar
More informationBasic Electrical Measurements
Page 1 of 11 Introduction Basic Electrical Measurements This Lab introduces the five basic, lumped circuit components or element models Resistor, Capacitor, Inductor, Voltage Source, Current Source. Also
More informationExercise 2: FACET Base Unit Familiarization
Exercise 2: FACET Base Unit Familiarization EXERCISE OBJECTIVE When you have completed this exercise, you will discover the operating features of the base unit and DC FUNDAMENTALS circuit board. You will
More informationENGR 210 Lab1. Ohm's Law
ENGR 210 Lab1 Ohm's Law Background In the class lectures we have discussed the fundamental electrical quantities of voltage, current and resistance. Since these quantities are so important there are specialized
More informationLab 4: Introduction to ELVIS II+ Introduction to ELVIS II+
Page 1 of 12 Laboratory Goals Introduction to ELVIS Lab 4: Introduction to ELVIS Familiarize students with the National Instruments hardware ELVIS Identify the capabilities of ELVIS Make use of the built
More informationOPERATING AND SERVICE MANUAL SPECIAL SUPPLEMENT
OPERATING AND SERVICE MANUAL SPECIAL SUPPLEMENT 11683A OPTION H01 POWER METER RANGE CALIBRATOR 11683-90010 Model Number: 11683A Option H01 Part Number: 11683-90010 Date Printed: June 5, 2012 2 11683A Option
More informationI. PANEL DESCRIPTION... 1
Table of Contents I. PANEL DESCRIPTION... 1 II. OPERATING INSTRUCTION... 7 1. MA OUTPUT... 7 1A. GENERAL OPERATION 4-20MA... 7 1B. SELECT 0-20MA OR 0-24MA... 8 1C. ENTER A VALUE LESS THAN 1... 9 2. % (PERCENTAGE)
More informationIDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL:
IDEAL INDUSTRIES, INC. TECHNICAL MANUAL MODEL: 61-796 The Service Information provides the following information: Precautions and safety information Specifications Performance test procedure Calibration
More informationMultidisciplinary Senior Design
Multidisciplinary Senior Design P10531: Piezoelectric Developer Sensor Standard Operating Procedure 12 May 2010 Dean Culver, Project Manager Thomas Siegwarth, Lead Engineer Thomas Bundy Elizabeth Cormier
More informationW Warning To avoid electrical shock, remove test leads and any input signals from the Model 707 Loop Calibrator before opening the case.
Model 707 Loop Calibrator W Warning To avoid electrical shock, remove test leads and any input signals from the Model 707 Loop Calibrator before opening the case. WCaution The Model 707 Loop Calibrator
More informationCalibration Kit. General Instructions. Table of Contents. System Requirements
Calibration Kit These instructions provide information on the installation, connection and operation of the Calibration Kit for use with SOR 805 Series pressure products, specifically the 805PT and 805QS.
More informationPIECAL 322 Automated Thermocouple Calibrator Operating Instructions. Product Description. Practical Instrument Electronics
PIECAL 322 Automated Thermocouple Calibrator Operating Instructions Product Description Easy to use With the PIECAL 322-1 you can check & calibrate all your thermocouple instruments and measure thermocouple
More informationOPERATING PROCEDURES for the UPS-S2 Universal Power Supply Series 2
OPERATING PROCEDURES for the Universal Power Supply Series 2 Vanguard Instruments Co., Inc. 1520 S. Hellman Ave. Ontario, California 91761 TEL: 909-923-9390 November 2013 FAX: 909-923-9391 REV. 2 SAFETY
More informationPIECAL 520B & 521B Thermocouple Source Operating Instructions
PIECAL 520B & 521B Thermocouple Source Operating Instructions (Shown without optional boot) Product Description (Shown with optional boot) Easy to use With the PIECAL 520B/521B you can check & calibrate
More informationCHAPTER 5. Voltage Regulator
CHAPTER 5 Voltage Regulator In your robot, the energy is derived from batteries. Specifically, there are two sets of batteries wired up to act as voltage sources; a 9V battery, and two 1.5V batteries in
More informationINSTRUCTION and OPERATIONS MANUAL. for
INSTRUCTION and OPERATIONS MANUAL for CAB SIGNAL MASTER MODEL NUMBER 15100-00 CAUTION Be sure to read and become thoroughly familiar with the entire contents of this manual before attempting to operate
More informationObjectives: - You need to be able to use the two equations above and the series and parallel circuit rules.
F: Solve Complete Circuits Level 3 Prerequisite: Solve Ohm s Law and the Power Formula Points To: Solve Complete Circuit with Nontraditional Information Objectives: V = IR P = IV - Given a battery and
More informationPROBLEMS PROBLEMS 203
P PROBLMS 203 This time, rather than using meters to make the measurements, we will use indicators. The ndicators key pad is the tenth down on the left toolbar. t has the appearance of an LCD display with
More information4. Enter LOCATION CODE 4.1 From LOCATION CODE screen press CHANGE button. Arrow points to first digit
5000 BIRD DOG PLUS STANDARD TEST PROCEDURE FOR SINGLE ELEMENT METER CIRCUIT TESTING ONLY (Save ONLY the GLOB SAVE Screen Forms 3, 4, 5, 6, 8, 9 Meter Circuits) 1. Hookup Probes to Phase A (or B or C as
More information4. Enter LOCATION CODE 4.1 From LOCATION CODE screen press CHANGE button. Arrow points to first digit
6000 BIRD DOG PLUS STANDARD TEST PROCEDURE FOR SINGLE ELEMENT METER CIRCUIT TESTING ONLY (Save ONLY the GLOB SAVE Screen Forms 3, 4, 5, 6, 8, 9 Meter Circuits) 1. Hookup Probes to Phase A (or B or C as
More information5 Performance Verification
5 Performance Verification Performance Verification TEST EQUIPMENT REQUIRED This procedure can be used to verify the warranted characteristics of the CP015 Current Probe. The recommended calibration interval
More informationOnboard calibration capability enables the HP E1413 to calibrate all 64 input channels in under 15 minutes, many times faster than the manual
Onboard calibration capability enables the HP E1413 to calibrate all 64 input channels in under 15 minutes, many times faster than the manual calibration techniques previously required in similar systems.
More informationSnail Gear Building instructions V1.0
Snail Gear Building instructions V1.0 Table of contents Components... 3 PCB layout... 4 General guideline for components... 5 General building tips... 5 Modifications... 6 Biasing... 7 Off board wiring...
More informationCOMPACTION METER TEST BOX, CMT-2.
COMPACTION METER TEST BOX, CMT-2. USER S MANUAL. Contents : page ------------------------------------------------------------------------------------------------- Contents and documents list... 1 Equipment
More informationLCx-xxxAx-8.08 Linear. Installation. Contents. Mounting: Short Instruction LCx-xxxAx Connecting Power and Signal
LCx-xxxAx-8.08 Linear Contents Installation pg1-3 Mounting Wiring Connecting Power and Signal Operation pg4-6 DIP Switch settings Controlling the Actuator Power Settings pg5 Signal loss and Calibration
More informationHAKKO FG-101 Calibration Instructions Revision
HAKKO FG-101 Calibration Instructions Revision 2013-10 Tools Required: Room Temperature Thermometer Yokogawa CA-71 Portable Calibrator or equivalent Yokogawa 2786 Decade Resistance Box or equivalent Fluke
More informationOhm Metrics Surface Resistance Testing Kit Model SRM500K
Ohm Metrics Surface Resistance Testing Kit Model SRM500K Instruction Manual Contents 1 Description SRM500K 1 Ohm Metrics 2 2 Operation Power Option 2 Set Up 2 Parallel Probe Resistivity Testing 3 Probe
More informationExperiment 1 Electrical Circuits Simulation using Multisim Electronics Workbench: An Introduction
Experiment 1 Electrical Circuits Simulation using Multisim Electronics Workbench: An Introduction Simulation is a mathematical way of emulating the behavior of a circuit. With simulation, you can determine
More informationVIZION INSTALLATION VERIFICATION GUIDE
1 VIZION INSTALLATION VERIFICATION GUIDE 2 Hardware Installation Verification Once the ViZion DR hardware has been installed it is important to test for proper hardware installation. This section of the
More informationMAE106 Laboratory Exercises Lab # 1 - Laboratory tools
MAE106 Laboratory Exercises Lab # 1 - Laboratory tools University of California, Irvine Department of Mechanical and Aerospace Engineering Goals To learn how to use the oscilloscope, function generator,
More informationDIGITAL MULTIMETER 4 1/2 digits, True RMS Model : DM-9027T
DIGITAL MULTIMETER 4 1/2 digits, True RMS Model : DM-9027T Caution Symbol Caution : * Risk of electric shock! Caution : * Do not apply the overload voltage, current to the input terminal! * Remove test
More informationDSTCAL Software User Manual 09/16/09 WD1037 Rev E Revised 09/09/14
DSTCAL Software User Manual 09/16/09 WD1037 Rev E Revised 09/09/14 Wahl Instruments, Inc. 234 Old Weaverville Road Asheville, NC 28804 Toll Free 800-421-2853 Phone 828-658-3131 Fax 828-658-0728 www.palmerwahl.com
More informationRCx-xxxAx Installation. Contents. Mounting: Holes for a mounting bracket. Holes are threaded for ¼-20 and are approximately.275 deep.
RCx-xxxAx-8.09 Contents Installation pg1-3 Mounting Wiring Connecting Power and Signal Operation pg4-6 DIP Switch settings Controlling the Actuator Torque Settings Signal loss and Calibration Troubleshooting
More informationProCal & ProCal-Track Calibration Software Features In Depth
Calibration Software ProCal & ProCal Track Calibration Software Full versions of are available to evaluate from the Transmille CD. ProCal-Track runs for 30 days after installation ProCal runs only the
More informationMZ Line tester. Contents. Reference: Date: October Version: 3
Contents I. INTRODUCTION... 2 II. Terminology... 3 III. Presentation... 4 Front panel... 4 TOP OF THE CASE... 5 ACCESSORIES SUPPLIED... 5 IV. CAUTION... 6 V. Operation... 7 TURN on and off... 7 MAIN FUNCTIONS...
More informationPIECAL CALIBRATORS. Milliamp Thermocouple RTD Voltage Frequency.
PIECAL CALIBRATORS Milliamp Thermocouple RTD Voltage Frequency www.piecal.com Accurate - Exceeds Expectations Reliable - Three Year Warranty Troubleshoot Loops - Automatic Diagnostics NIST Traceable -
More informationModels 6522, 6524, 6526, 6532, 6534 & 6536
Special product features MEGOHMMETERS & Multi-Function Handheld HAND HELD Models 6522, 6524, 6526, 6532, 6534 & 6536 T TRUE MEGOHMMETER IP 54 Rated SELECTABLE TEST VOLTAGES SPECIFICATIONS MODELS 6522 6524
More informationCreated by: T.Tetreault Date:14jul 92 PAGE 1 OF 5
Rev Date Appd DCN B 7/14/92 RPC --- C 11/26/96 RPC --- D 26SEP00 TJT 10394 Suggested Equipment: 1) 5 digit ohm meter, capable of 4-wire measurements. (Accuracy ±0.005% of reading or better, with an excitation
More informationAdafruit USB Power Gauge Mini-Kit
Adafruit USB Power Gauge Mini-Kit Created by Bill Earl Last updated on 2017-07-14 11:55:04 PM UTC Guide Contents Guide Contents Overview Assembly Basic Assembly Solder the female connector. Solder the
More informationCHAPTER 3B: ELECTRONIC POWER STEERING
Electronic Power Steering CHAPTER 3B: ELECTRONIC POWER STEERING NOTE: The basic steering system, such as the tie rod ends, drag links axles, etc., is covered in Chapter 3A: Steering. In 2012, Cub Cadet
More informationAirTest Model CN9000 Series Sensor Controller
AirTest Model CN9000 Series Sensor Controller AirTest Model CN9000 Series Sensor Controller THEORY OF OPERATION A basic CN9000 configuration consists of Input/Process/Display combination modules, a 3 relay
More informationAgilent E3640A E3649A Programmable DC Power Supplies. Data Sheet
Agilent E3640A E3649A Programmable DC Power Supplies Data Sheet Reliable Power, Repeatable Results Single and dual outputs Dual range output 30 W to 100 W output power Front and rear output terminals Over-voltage
More informationST1016 INSTRUMENTATION FOR RENEWABLE ENERGIES
16 ST1016 INSTRUMENTATION FOR A wide range of electrical., electronic and physics instrumentation for measure, control and testing, is available for this advanced laboratory. 56 DIGITAL MULTIMETER These
More informationPLCMTR Commercial Grade Camera System
Please read instructions carefully before installation and use. Installation should be performed by a professional installer. To ensure your safety, the driver should not watch videos or operate features
More informationATL55, AAC3, ATT29, ATT70, 9V Bat., AF38, AF39. Range Resolution Accuracy DC Current DM393 DM µA 0.1µA 1.0% % + 2
DM393 DM391 Functions Features True RMS AC Volts and Amps 1000V AC/DC 10A AC/DC 0.5% basic DC accuracy Frequency 10Mhz Capacitance 100µF Temperature: 40 to 2372 F Resistance 40MΩ Diode test 4V >10Ω All
More informationUser s Guide 200 ma Current Source Module CSM-39020
User s Guide 200 ma Current Source Module CSM-39020 ILX Lightwave Corporation 31950 Frontage Road Bozeman, MT, U.S.A. 59715 U.S. & Canada: 1-800-459-9459 International Inquiries: 406-556-2481 Fax 406-586-9405
More informationPDF # CEN TECH DIGITAL MULTIMETER INSTRUCTIONS EBOOK
01 March, 2018 PDF # CEN TECH DIGITAL MULTIMETER 98025 INSTRUCTIONS EBOOK Document Filetype: PDF 245.69 KB 0 PDF # CEN TECH DIGITAL MULTIMETER 98025 INSTRUCTIONS EBOOK This cen tech manual de multimetro
More informationPIECAL 510B/511B RTD Simulator Operating Instructions
PIECAL 510B/511B RTD Simulator Operating Instructions (Shown without optional boot) (Shown with optional boot) Product Description Easy to use With the PIECAL 510B/511B you can check & calibrate all your
More informationTeaching Computer-Based Data Acquisition and Analysis Research Skills Using LabVIEW
Teaching Computer-Based Data Acquisition and Analysis Research Skills Using LabVIEW OUTLINE: John Essick Reed College Reed Advanced Laboratory LabVIEW-Based Instruction Required Cost and Time for Instruction
More informationIntroduction. Chapter 2
The Vantage PRO unit (Figure 2-1) combines a digital and graphing multimeter, lab scope and ignition scope with a powerful diagnostic database. Figure 2-1 Vantage PRO This diagnostic database gives you
More informationModel PC20 Intelligent Field Device Configurator for Use with Transmitters with FoxCom or HART Communication Protocol
Product Specifications Model PC20 Intelligent Field Device Configurator for Use with Transmitters with FoxCom or HART Communication Protocol PSS 2A-1Z3 E MODEL PC20 PC-BASED FIELD DEVICE ON CD-ROM The
More informationPRODUCT INSTRUCTIONS MODEL SR-2 SOIL RESISTIVITY METER
DESCRIPTION: The Model SR-2 Soil Resistivity Meter is an electronic instrument useful in finding the resistance of soil at various depths. Uses: New Pipeline Surveys Direct Assessment Surveys U.S.T. Surveys
More informationLab 2.2 Ohm s Law and Introduction to Arduinos
Lab 2.2 Ohm s Law and Introduction to Arduinos Objectives: Get experience using an Arduino Learn to use a multimeter to measure Potential units of volts (V) Current units of amps (A) Resistance units of
More informationUser Manual VX4234 Digital Multimeter Module
User Manual VX4234 Digital Multimeter Module 070-9139-02 This document applies for firmware version 1.00 and above. General Safety Summary Review the following safety precautions to avoid injury and
More informationIntroduction to Electronics Workbench
Introduction to Electronics Workbench Electronics Workbench (EWB) is a design tool that provides you with all the components and instruments to create board-level designs on your PC. The user interface
More informationThorlabs Model LD1100
Thorlabs Model LD1100 Constant Power Laser Driver THORLABS, Inc. PO Box 366 435 Route 206N Newton, NJ 07860 (973) 579-7227 Phone (973) 383-8406 Fax http://www.thorlabs.com Page 1 of 15 Table of Contents
More informationVW2110 Vibrating Wire Readout Calibrator Manual
VW2110 Vibrating Wire Readout Calibrator Manual All efforts have been made to ensure the accuracy and completeness of the information contained in this document. RST Instruments Ltd reserves the right
More informationUsing a HP02 with the Eagle Batching System
Hydronix Engineering Note Hydronix Ltd, 7 Riverside Business Centre, Walnut Tree Close, Guildford, Surrey GU1 4UG, England +44 (0) 1483 468900 +44 (0) 1483 468919 www.hydronix.com Using a HP02 with the
More informationDRTS 3 PLUS Advanced Protection Relay Test Set and Measurement System
Advanced Protection Relay Test Set and Measurement System Multi-tasking equipment designed for testing protection relays, energy meters, transducers Particularly designed to test RTU (remote terminal unit)
More informationECE 270 Lab Verification / Evaluation Form. Experiment 1
ECE 70 Lab Verification / Evaluation Form Experiment Evaluation: IMPORTANT! You must complete this experiment during your scheduled lab period. All work for this experiment must be demonstrated to and
More informationExperiment 4.A. Speed and Position Control. ECEN 2270 Electronics Design Laboratory 1
.A Speed and Position Control Electronics Design Laboratory 1 Procedures 4.A.0 4.A.1 4.A.2 4.A.3 4.A.4 Turn in your Pre-Lab before doing anything else Speed controller for second wheel Test Arduino Connect
More informationHT-1A Dual Band CW QRP Transceiver. User Manual
HT-1A Dual Band CW QRP Transceiver User Manual Rev A, June 17, 2018 Designed by BD4RG Exclusively distributed by CRKITS.COM and its worldwide distributors Join the group http://groups.io/g/crkits to get
More informationInfiniium X / L- Series Oscilloscopes
Service Guide Publication Number 54916-97009 October 2013 Agilent Technologies, Inc. 2011-2013 Infiniium 90000 X / L- Series Oscilloscopes Agilent Infiniium 90000 X-Series Oscilloscopes at a Glance Ease
More informationE5071C Adjustment Program. <Agilent Service Center Use Only> Operation Manual. Second Edition. Agilent Part No. N/A
E5071C Adjustment Program Operation Manual Second Edition Agilent Part No. N/A November 2006 Notices The information contained in this document is subject to change without notice. This document contains
More informationService Guide. Publication Number March Agilent Technologies, Inc Infiniium A-Series Oscilloscopes
Service Guide Publication Number 54913-97022 March 2013 Agilent Technologies, Inc. 2007-2013 Infiniium 90000 A-Series Oscilloscopes Agilent Infiniium 90000 A-Series Oscilloscopes at a Glance Ease of use
More informationEE 324 L SIMULATION LABORATORY
Experiment No. 9 EE 324 L SIMULATION LABORATORY FAULT ANALYSIS OF A SIMPLE AC SYSTEM USING PSCAD Objective: Simulate the given power system network for L-L, L-L-G, L-L-L and L-L-L- G faults. Determine
More informationBA505C 2-wire 4/20mA manual setpoint station Issue 6
BA505C 2-wire 4/20mA manual setpoint station Issue 6 Issue: 6 3 rd December 2010 2 CONTENTS 1. Description 2. Operation 3. Electrical Systems Design 3.1 4/20mA loop 3.2 Optional Backlights 3.2.1 Separately
More informationPZ4000 Product Tutorial. Product Tutorial
PZ4000 HIGH FREQUENCY POWER ANALYZER PZ4000 POWER ANALYZER MEASUREMENT LAB OVERVIEW & OBJECTIVES The following is a basic demo procedure for the PZ4000 Power Analyzer. This demo uses the power meter s
More informationPacific Antenna Two Tone Generator
Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination
More informationCH2 Performance Verification Manual For the CH2 using easy-wire software version 2009 or higher
CH2 Performance Verification Manual For the CH2 using easy-wire software version 2009 or higher Version 2014 June 10, 2014 An ISO 9001 Certified Company CH2 Performance Verification Manual Version 2014.1.0
More information709/709H. Calibration Manual. ma Loop Calibrator
709/709H ma Loop Calibrator Calibration Manual May 2013 2013 Fluke Corporation. All rights reserved. Specifications are subject to change without notice. All product names are trademarks of their respective
More informationUser's Guide. Phase Sequence and Motor Rotation Tester Model
User's Guide Phase Sequence and Motor Rotation Tester Model 480403 Introduction Congratulations on your purchase of the Extech Model 408403 Motor and Phase Rotation Indicator. This handheld instrument
More informationTreadmill Embedded Touch Screen Won t Power Up
Treadmill Embedded Touch Screen Won t Power Up E-TRe and E-TRxe This document contains the necessary information to troubleshoot a treadmill with an embedded touch screen that will not power up. Follow
More informationFluke 8845A/8846A Digital Multimeters. Precision and versatility for bench or systems applications
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Fluke 8845A/8846A Digital Multimeters Precision and versatility for bench or systems
More informationFluke 180 Series Digital Multimeters Features
Fluke 180 Series Digital Multimeters Features Features at a Glance ToolPak LockPak FlukeView Forms Software Safety Features Lifetime Warranty Features at a Glance Basic DC accuracy of 0.025%. 50,000-count
More informationPower Prowler. Quick Start Guide. 3-In-1 DMM/TDR Cable Fault Finder for Energized and Unenergized Cables 600V CAT III. For Live Energized Cables
Power Prowler 3-In-1 DMM/TDR Cable Fault Finder for Energized and Unenergized Cables Quick Start Guide 600V CAT III For Live Energized Cables PLR600 Revison 08/19/13 www.t3innovation.com Soft key functions
More informationKeysight Infiniium 9000 Series Oscilloscopes
Keysight Infiniium 9000 Series Oscilloscopes Service Guide Service Guide Publication Number 54904-97014 October 2013 Infiniium 9000 Series Oscilloscopes The Keysight Technologies Infiniium 9000 Oscilloscope
More informationTroubleshooting guide for the S100 Energy meter and EPS
Troubleshooting guide for the S100 Energy meter and EPS The S100 Energy Meter is the brains of the Sungrow hybrid system. It tells the inverter when to charge or discharge the battery, when to go into
More informationIMP-2MC ELECTRODE IMPEDANCE TESTER MULTICHANNEL
MicroProbes for Life Science IMP-2MC ELECTRODE IMPEDANCE TESTER MULTICHANNEL User Instructions Version: January, 2016 18247-D Flower Hill Way Gaithersburg, MD 20879 Phone: +1 301 330-9788 Fax: +1 301 330-9667
More informationMultifunction Calibrator
Multifunction Calibrator Model CL TC - - - C V _ TECPEL CO., LTD. Features:. - (KΩ load, V Loop Supply). -.,-.V, -.V. K, J, E, T Thermocouple ( C and ). Frequency -.. Basic Accuracy. Easy Key-pad Operation.
More informationUsing solderless breadboards
Page 1 of 9 Using solderless breadboards This document describes how to use the solderless breadboards available in the experimental didactic lab (LED, previously LADISPE) of Politecnico di Torino. 1 Setting
More informationGraphing and Describing 180 Rotations about the Origin (0, 0)
Lesson: Graphing and Describing 180 Rotations about the Origin (0, 0) Day 5 Supplement Lesson Graphing and Describing 180 Rotations about the Origin (0, 0) Teacher Lesson Plan CC Standards 8.G.3 Describe
More informationAppendix D: Equipment
Appendix D: Equipment ELECTROSTATIC PAPER AND ACCESSORIES: To investigate electric fields with the electrostatic paper, you need to do the following: Lay the electrostatic paper flat.. Distribute the pieces
More informationAgilent E3632A DC Power Supply
Service Guide Part Number: E3632-90010 October 2007. For Warranty information, refer to the back of the manual. Copyright Agilent Technologies, Inc. 2000-2007 All Rights Reserved. Agilent E3632A DC Power
More informationOPERATING INSTRUCTION. Pen-Type Digital Multimeter
OPERATING INSTRUCTION Pen-Type Digital Multimeter International Safety Symbols This symbol, adjacent to another symbol or terminal, indicates the user must refer to the manual for further information.
More informationTorque Control Verifier
Torque Control Verifier Instruction Manual Revision 1.2 September 2002 Please Read and Understand Instructions Before Attempting Installation Torque Control Verifier Contents: Quick Start Introduction
More informationBrought to you by Jestine Yong
Bonus Report Brought to you by Jestine Yong http://www.electronicrepairguide.com http://www.testingelectroniccomponents.com You cannot give this bonus report away for free. You do not have the rights to
More informationZero Volt Monitor Installation, Operation and Maintenance
TECHNICAL BULLETIN TB-6515 Zero Volt Monitor Installation, Operation and Maintenance Made in the United States of America strap properly, the monitor measures the loop resistance consisting of one wire
More information10 THINGS YOU MUST KNOW BEFORE BUYING YOUR NEXT Benchtop Digital Multimeter
THINGS YOU MUST KNOW BEFORE BUYING YOUR NEXT Benchtop Digital Multimeter Introduction The digital multimeter (DMM) is the most commonly used instrument on an engineer s bench. We use it almost every day.
More informationAC : A NEW PEDAGOGY FOR THE ELECTRONICS LABORA- TORY
AC 2011-801: A NEW PEDAGOGY FOR THE ELECTRONICS LABORA- TORY Daren Reed Wilcox, Southern Polytechnic State University Gerd Walter Wstenkhler, Hochschule Harz (University of Applied Sciences) c American
More informationInfiniium Q- Series Oscilloscopes
Service Guide Publication Number 54932-97006 October 2013 Agilent Technologies, Inc. 2012-2013 Infiniium 90000 Q- Series Oscilloscopes The Agilent Technologies Infiniium 90000 Oscilloscope at a Glance
More informationKeysight Technologies Using Source/Measure Unit as an Ammeter
Keysight Technologies Using Source/Measure Unit as an Ammeter B2900A Precision Source/Measure Unit Demo Guide 02 Keysight Using Source/Measure Unit as an Ammeter Demo Guide Introduction The Keysight B2900A
More informationFluke 8845A/8846A Digital Multimeters. Precision and versatility for bench or systems applications
Fluke 8845A/8846A Digital Multimeters Precision and versatility for bench or systems applications Exceed your expectations With 14 measurement functions, math and analysis modes, the 8845A/8846A will meet
More informationUser Guide. Model Temperature Datalogger Kit Model Temperature and Humidity Datalogger Kit Model SW276 Datalogging Software SW276
User Guide Model 42265 Temperature Datalogger Kit Model 42275 Temperature and Humidity Datalogger Kit Model SW276 Datalogging Software SW276 Introduction Congratulations on your purchase of Extech Instrument
More informationAssembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.
NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit
More informationEV Evaluation System User Guide. Contents. Kit Contents. Introduction
Contents EV2200 40 Evaluation System User Guide Section Page No. Introduction 1 Kit Contents 1 Hardware and Software Setup 2 Software Installation 2 Hardware Connection 2 Operation 2 Starting the Program
More informationWhat is Locktronics? Science and technology. Electronics. Engineering. Automotive. Aviation maintenance. Simplifying Electricity & Electronics
What is Locktronics? Simplifying Electricity & Electronics Locktronics is a range of products that simplifies the process of learning and teaching electricity and electronics. The core range consists of
More informationP522 Signal Processor
P522 Signal Processor INSTALLATI INSTRUCTIS Self-Check Contact Ratings: Max switching power - 60 W 125Vac Max switching voltage - 220VDC, 250Vac Max switching current - 2A DC, AC Analog Flame Signal: User
More information