Manual. Dimmer DMD-12-2

Transcription

1 Manual Dimmer DMD-12-2

2 Table of contents 1. Safety instructions For safe and efficient operation Overview Front view Rear view Termination Operating guide Display and standby mode Menu DMX Fail Patching Minimum Level Maximum Level Preset Curve Technical data / 16

3 1. Safety instructions Read the safety instructions and also this manual carefully. Keep the manual. Observe all red flags. Observe the manual. To prevent fire or electric shocks, protect the device against rain and humidity Pull the plug before opening the housing. To prevent an electric shock you should not remove the cover. Do not operate the device in the near of water. Use only a dry cloth for cleaning For safe and efficient operation Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance. Not put it in a temperature bellow 32 F /0 C, or exceeding 104 F /40 C. To avoid placing on un-stable location Select a level and stable location to avoid vibration. Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt. Pull the plug before cleaning. If out of work, contact sales agency immediately Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not open the cabinet by yourself, it might result a danger of electric shock. Take care with the power cable Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. When not using the device for an extended period of time, be sure to disconnect the plug from the receptacle. Ventilation It is not allowed cover fans and air in and outlets. 3 / 16

4 Safety Do not remove the grounding. It is for your safety. If you remove the grounding it can cause electric shocks. Accessory Please use only the accessory which is set by the manufacturer. Important Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems. Make sure the electrical connection is carried out by qualified personnel. All electrical and mechanical connections have to be carried out according to the European safety standards. 4 / 16

5 2. Overview 2.1. Front view 1. Display 2. DMX LED This LED light up if there is a DMX signal.. 3. MENU Press this button to get into the menu. 4. UP/DOWN With this button you can increase/decrease a value. Pressing and holding the button will increase/decrease the value quickly. 5. ESC With this button you can exit the menu. 6. Channel dimmer module The channel dimmer module is incorporated with a 10A circuit breaker and SCRs (Silicon Controlled Rectifier) with 1000A peak current capacity. 5 / 16

6 2.2. Rear view 1. Analogue input DC 0-10 V 2. DMX IN 3pol XLR input male. 3. DMX OUT 3pol XLR output female Termination 6 / 16

7 3. Operating guide 3.1. Display and standby mode Power on this unit, the LCD shows the revision of software immediately, then enter standby mode automatically, the LCD shows the dimming level of each channel as below. The first row indicates the dimming level, and the second row indicates the channel (1 stands for channel 1, 2 stands for channel 2, and so on. A, B and C stand for channel 10, 11 and 12.) Menu In standby mode tap MENU to enter the menu. There are 6 menus: DMX Fail, Patching, Minimum Level, Maximum Level, Preset and Curve, all other menu settings will be stored into a memory. Tap ESC to leave the menu DMX Fail 1. Press UP/DOWN to get to the DMX Fail menu. 2. Press MENU again to get to the submenu. With UP/DOWN you can choose between Last Hold, Analog and Program Last Hold Last received DMX signal is held. Analog The analogue input is activated. Program Starts the default programs If you select Last Hold or Analog you can tap ESC to exit.. 7 / 16

8 4. If you select Program01-12 tap ESC. Now you can set the velocity. 5. Using UP/DOWN you can select the velocity from 00,05s to 30.00s. 6. After you have finished your setting, tap ESC button to exit Patching 1. Press UP/DOWN to get to the Patching menu. 2. Tap MENU, to enter sub-menu. You can use UP/DOWN to choose between Start and Independent. Start address Complete dimmer (12 channels) has only one start address. Independent addr The DMX address of each channel is selectable, and all channel can select the same DMX addresses. 3. Tap UP/DOWN to scroll to Start address or Independent addr and tap MENU to enter the submenu. 8 / 16

9 4. In Start address you can use UP/DOWN to set the starting address of all 12 channels from If you select Independent addr you can tap UP/DOWN to scroll to All and Single. Tap MENU to enter the submenu. 6. In All mode tap UP/DOWN to select the DMX address from In All mode, complete dimmer (12 channels) has only one start address. 7. In Single mode tap MENU to select between channel and address. In Single mode, the DMX address of each channel can be selectable separately. 8. When channel is activated, tap UP/DOWN to select from When Addr is activated, tap UP/DOWN to select from After you have finished your setting, tap ESC button to exit. 9 / 16

10 Minimum Level 1. Press UP/DOWN to get to the Minimum Level menu. 2. Tap MENU, to get to the submenu. 3. Tap UP/DOWN to select between All and Single. Tap MENU to get into the menu. 4. In All mode, tap UP/DOWN to select Minimum Level value of all channels between 00%-30%. 5. In Single mode, tap MENU to select between channel and Minimum Level value. 6. When Chan is activated, tap UP/DOWN to select from 01-12, when Minimum Level value is activated tap UP/DOWN to select from 00%- 30%. 7. After you have finished your setting, tap ESC button to exit. 10 / 16

11 Maximum Level 1. Press UP/DOWN to get to the Maximum Level menu. 2. Tap MENU, to get to the submenu. 3. Tap UP/DOWN to select between All and Single. Tap MENU to get into the menu. 4. In All mode, tap UP/DOWN to select Maximum Level value of all channels between 070%-100%. 5. In Single mode, tap MENU to select between channel and Minimum Level value. 6. When Chan is activated, tap UP/DOWN to select from 01-12, when Minimum Level value is activated tap UP/DOWN to select from 070%- 100%. 7. After you have finished your setting, tap ESC button to exit. 11 / 16

12 Preset This menu allows you to momentarily adjust of all channels or individual channel and all your settings in this menu will be lost when power is off. 1. Press UP/DOWN to get to the Preset menu. 2. Tap MENU, to get to the submenu. 3. Tap UP/DOWN to select between All and Single. Tap MENU to get into the menu. 4. In All mode, tap UP/DOWN to select the dimming level value of all channels between 000%-100%. 5. In Single mode, tap MENU to select between channel and dimming level value. 6. When Chan is activated, tap UP/DOWN to select from 01-12, when the dimming level value is activated tap UP/DOWN to select from 000%-100%. 7. After you have finished your setting, tap ESC button to exit. 12 / 16

13 Curve Press UP/DOWN to get to the Curve menu. 2. Tap MENU, to get to the submenu. 3. Tap UP/DOWN to select between All and Single. Tap MENU to get into the menu. 4. In All mode, tap UP/DOWN to select between Linear, S-Curve, Non Dim and Square. 5. In Single mode, tap MENU to select between Linear, S-Curve, Non Dim and Square. 6. When Chan is activated, tap UP/DOWN to select from 01-12, when the dimming level value is activated tap UP/DOWN to select between Linear, S- Curve, Non Dim and Square. 7. After you have finished your setting, tap ESC button to exit. 8. Tap ESC to get back to standyby mode.. 13 / 16

14 4. Technical data Power supply Channel Output (3 Phases) Chanel Output Voltage 10 A/CH; 3x40 A 10 A/CH; Total: 120 A 32 A. 400 V AC Connections Current in Current out XLR in/out Terminal block Terminal block 3pol XLR Controlling Dimming curve Switch Automatic DMX512 Linear, S-Curve Switch/Square Yes Yes Number of DMX channels 12 Dimensions Weight 483 x 178 x 436 mm 31 kg 14 / 16

15 15 / 16

16 Importer: B & K Braun GmbH Industriestraße 2 D Karlsbad info@bkbraun.com 16 / 16