YOUR EXPERT IN GENERATOR SOLUTIONS. NEW GENSYS/MASTER 2.0 Range V5.03 Firmware. NEW CRE Config V2.80 SOFTWARE

Transcription

1 YOUR EXPERT IN GENERATOR SOLUTIONS NEW GENSYS/MASTER 2.0 Range V5.03 Firmware NEW CRE Config V2.80 SOFTWARE V_092017

2 Improvements & CORRECTIONS CRE config software (V2.80) GENSYS2.0 range (V5.03a1) MASTER2.0 (V5.03a1) RDM2.0 (V5.03a1) RDM3.0 (V5.03a1)

3 CRE Config Software(V2.80) Automatic Software updater: SOFTWARES If computer is connected on Internet, and «check for update» is activated, CRE config software will be able to automatically update with last software version, Automatic Products Firmware updater: When PC connected to any CRE product, CRE config software will propose you to update your products with the latest firmware available,

4 CRE Config Software(V2.80) Improvement of Bitfields capacity to optimize Modbus communication, SOFTWARES

5 CRE Config Software(V2.80) Improvement on SCADA page to gather information / measurements, SOFTWARES

6 CRE Config Software(V2.80) Improvement on J1939 measurements pages, SOFTWARES

7 CRE Config Software(V2.80) Updated functions and parameters to match with new firmware v 5.03a1, New MASTER2.0 products added in the range, Gensys Compact curve editor for analog inputs SOFTWARES calibration added, Unigen 2.0 curve editor for analog inputs calibration added, Simplified label management when product and PC languages are different, Improvement of old software versions management, Improvement of MTU/MDEC communications,

8 GENSYS 2.0 range Voltage measurements has been increased up to 65kVac, Lists of configurable functions available on digital inputs and digital outputs have been increased, Overflow Alarms on generator kwh, kvarh, running hours and Mains kwh, kvarh) have been added, Improvement of PID Dynamic factory range:

9 GENSYS 2.0 range 5 configurable user bitfields have been added in order to simplify Modbus request,

10 GENSYS 2.0 RANGE In manual mode, the synchronization demand can be cancelled without stopping the generator, In manual mode, the generator breaker closure is only allowed when engine is ready, GENSYS2.0 Marine could be configured as alone, Improvement of Load Sharing accuracy, Improvement of CANopen compatibility with configuration files from v4.77a1 and lower. Display pages for digital extensions inputs/outputs have been added. Maximum generator nominal powers have been increased up to kW and kVAR.

11 GENSYS 2.0 range Improvement and multi languages of warning/error messages after equations file compilation.

12 GENSYS 2.0 range Improvements of breaker output control : - On dead bus management, when breaker closed during the data acquisition for RMS measurement, - On dead bus management, when breaker position feedback takes more than 100ms. - On configuration 1 x GENSYS x MASTER2.0, Corrections and updates on the Embedded website, in order to increase reliability with AJAX technology,

13 GENSYS 2.0 range Improvements : - RMS measurements, - Generator current measurements with breaker open when current transfo ratio is low, - Neutral current measurements, - Load/unload management by hours if 1 generator is above hours, - The unload management for power plant with more than 16 generators, - Recovering the own variables trough broadcast data on inter-gensys bus CAN,

14 GENSYS 2.0 range Improvements: - Vector jump protection accuracy and trigger, - Generator protections kw, - kvar, min kw, max kw, min kvar, max kvar, - Web server connection trough Ethernet - Connection between GENSYS2.0 and RDM2.0 (lost of frames, disconnection, latency),

15 GENSYS 2.0 range : improvements: - Digital Output function «air fans», - Correction of corruption between some specific variables used with equation and the bitfield variables, - Correction of mismatching between virtual start E2514 and remote start E2002 in some cases, - Unload ramp with small generator (<100kW)

16 MASTER 2.0 New products : MASTER 2.0 CORE, MASTER 2.0 CORE, GENSYS2.0 CORE MASTER, Improvements - Display/configuration menus, - Power plant paralleled with mains with only 1 breaker, - Possibility to download configuration file when Mains breaker is closed, - In manual mode, power plant breaker closure is only allowed when power plant is ready, - CAN bus fault between MASTER2.0 and GENSYS2.0 management,

17 MASTER 2.0 Improvements - Transition between synchronization and load transfer, from Island to Mains or opposite, - When power plant is controlled by analog output, - Load shedding feature, - MASTER 2.0 election, in case of several MASTER 2.0 products (several mains applications), - Voltage correction from MASTER 2.0 to GENSYS2.0, during start on «static paralleling» sequences, - Technical documentation totally updated.

18 RDM2.0 Only use RDM2.0 firmware version V5.03 with GENSYS2.0 v5.03 or higher, Management of new products references : - RDM2.0 MASTER P/N : A54Y0 - RDM2.0 MASTER P/N: A53C9, LCD screen contrast and backlight management similar as GENSYS 2.0 product, New display pages according with GENSYS 2.0 firmware V5.03, Information pages improvement to follow GENSYS 2.0 one,

19 RDM2.0 Equations exported on SD card according to RDM 2.0 password level, Improvement of password modification on RDM 2.0, (previously not taken into account after re-boot of the associated GENSYS 2.0),

20 RDM3.0 New GENSYS2.0 v5.03 pages protections, New page about Ethernet configuration, New page for idle parameters configuration (idle screen / idle mode timers), Alarms/Faults are now saved on history part, New «setup» system to update the RDM3.0 firmware MONITORING version, To update labels on RDM3.0, from GENSYS2.0 units, just use the function : «refresh labels», RDM3.0 time and date is now synchronised with GENSYS2.0 on real time,

21 YOUR EXPERT IN GENERATOR SOLUTIONS