PMCG - MANUAL PMCG ORIGINAL INSTRUCTIONS. Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland
|
|
- Logan Robinson
- 6 years ago
- Views:
Transcription
1 PMCG ORIGINAL INSTRUCTIONS Manufactured: Designed: Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland info@preservatech.eu Preservatech Inc Toronto, Canada info@preservatech.com 1
2 Table of Contents INTRODUCTION... 3 DIMMENSION... 4 Packing List... 4 INSTALLATION... 5 SETTING UP... 6 ALARM CONNECTION... 7 DATA LOGGER... 7 MASTER SLAVE CONFIGURATION... 8 A SETTING MODE... 8 B- FULL MASTER/SLAVE MODE... 9 Setting machine to be used as Master or Slave Setting Mode B. FULL MASTER/SLAVE MODE PROGRAMMING MANUAL USER MODE PROGRAMMING MODE PARAMETERS LIST SETTING DATE/TIME MODE DATE/TIME PARAMETERS LIST Network connection Shipping and storage LIMITED MICROCLIMATE GENERATOR WARRANTY Declaration of Conformity
3 INTRODUCTION Preservatech's PMCG generator is a miniature humidity control device for museum showcases and similar small sealed enclosures. This unit can reliably control humidity for individual well sealed enclosures. When properly installed, this microclimate control system will typically maintain the relative humidity level in a sealed enclosure within two percent (or less) of an operator determined value. Depending upon the ambient temperature conditions and enclosure construction, relative humidity levels of less than twenty to over sixty percent can be attained. This unit will work only with high quality display cases with an air change rate of 0.2 per day or better. This manual will assist you in installing and setting up the unit as well, it contains complete instructions on operating the unit. Please note the cautions and warnings, as the unit may not provide optimum performance if all directions are not carefully followed 3
4 DIMMENSION PACKING LIST Every machine shipment consists of: 1. PMCG generator. (1 pc) 2. Silicone hose for connecting to display case (2 m) 3. Through wall air connector (2 pcs) 4. Humidity sensor. (1pc) 5. Power cord. (1 pc) Optional (not included in standard package) 6. External alarm cable and LED. 7. External booster fan 4
5 INSTALLATION The PMCG unit re-circulates air inside the case. Installation is very simple and includes: - Connection of the PMCG unit to the case, using two flexible hoses made of silicone (or other material approved by conservator), hoses outside diameter: 7/8-22 mm (included) - Hose connecting machine OUT port with the case should be as short as possible, input hose can be longer. - Installation of the RH sensor inside the case (to get most stable humidity inside the case, sensor should be located close to the air input but not directly in the air stream). - Connection to a standard, grounded power outlet VAC. WARNING: POWER OUTLET MUST BE PROPERLY GROUNDED. - Setting up proper RH level (see next chapter) DISPLAY CASE Distance between air fittings, should be as far away as possible SENSOR PMCG 5
6 SETTING UP The machine is controlled by a microprocessor located at the front of the machine. Using 5 buttons, located on the right side of the display, it is possible to switch display between, "RH" - actual value of RH measured by machine sensor (left top button) "SET" - target RH value (left bottom button) and "ALA" - out of range alarm deviation (center button). See detailed instruction below. For more comprehensive instruction of microprocessor programming, please see our "PMCG - Programming Manual". Shows actual RH value measured by machine sensor RH-measured humidity-read only SET-target humidity Target RH value. Press GREY button, change value using up/down buttons, save with GREY button INCREASE/DECREASE VALUE ALA-out of range alarm Value offset for OUT OF RANGE ALARM. INCREASE/DECREASE VALUE Alarm will be triggered when RH>(SET+ALA) and/or when RH<(SET-ALA) 6
7 ALARM CONNECTION PMCG machines have an alarm connector on the back of the machine. Optionally the machine can be shipped with 2 meters of cable and a small red LED light. LED can be located away from the machine, to indicate "RH OUT OF RANGE" status. connected properly: RED to BROWN and BLACK to BLUE. LED light is powered by 12 VDC and LED's leads should be DATA LOGGER Some of the machines are equipped with a built-in data logger. The data logger records the actual measurements on a SD card (not included). Time intervals can be changed between 1 and 60 minutes in 1 minute increments, please see "Programming Manual". Data written on the SD card, can be read in our free software or in any other software able to read CSV files (eg. Excell) IMPORTANT: SD Card used in our data loggers must be formatted as FAT32 file systems. Other file systems are not compatible with data loggers. For properly working data logger, Date and Time as well as LOG parameter, must be properly set. Please see pages for instruction how to set Time, Date and LOG parameters. LOG represents interval between writing data od SD Card in minutes. LOG = 0 Data logger is turned off. 7
8 MASTER SLAVE CONFIGURATION PMCG machines can be set in Master-slave configuration. There are two possible Master/Slave modes: A SETTING MODE IN THIS MODE, ANY PMCG AND/OR MINI ONE UNITS CAN BE CONNECTED TOGETHER. One machine is set as a Master unit then connected to the remaining machine(s) by Ethernet cable using cable splitters. Slave units (receiving units) have their own sensors. The Master unit only sends a signal of the set value to the slave controllers. MASTER SLAVE SLAVE SLAVE Ethernet This mode is good if there are many PMCG s (or Mini Ones) and all of them should be set to the same value. Master units work as a remote: setting all other units to the same humidity value. 8
9 B- FULL MASTER/SLAVE MODE IN THIS MODE, ONLY SAME MODEL MACHINES CAN BE CONNECTED. One machine is set as Master and one is set as Slave. Slave unit doesn t have a sensor and works exactly as the Master unit. MASTER SLAVE Ethernet This mode is best if two machines are working with a single, larger display case. 9
10 SLAVE MASTER PMCG - MANUAL Setting machine to be used as Master or Slave Any machine can be set as Master or Slave. To set a machine to work as Master/Slave, few parameters in the controller software must be changed. Setting Mode 1. All machines to be part of master/slave configurations need to be connected using standard Ethernet cables and cable splitters (easily available in any computer store). Connector is located on the back wall of the machine and is marked as NETWORK. All machines are connected to the cases in the same way as in independent mode. 2. Master unit need to be reprogrammed as follows: Parameter Value to be set Factory set value Notes Slave unit(s) needs to be reprogramed as follows: Parameter Value to be set Factory set value Notes Each slave unit needs to have own unique address. 0 0 No change to factory set 0 0 No change to factory set 0 0 No change to factory set 10
11 Every time, set value on MASTER UNIT will change, all slave units will change their own set value to match master value. PLEASE SEE PROGRAMMING CHAPTER FOR EXACT INSTRUCTION HOW TO ENTER PROGRAMMING MODE. B. FULL MASTER/SLAVE MODE In this configuration, only one pair of machines can be connected (one Master, one Slave). The Slave unit will receive all readings from the Master unit and mimic the Master unit operation. Controller on the Slave unit will not work and sensor on slave unit is disconnected. Display on Slave unit will change to S. Machines can be connected to the controlled case in series or parallel. In Series Hose from the case is connected to the Air from case connector on the Master unit, Air to case on Master is connected to the Air from case on the Slave unit and Air to case on Slave is connected to the display case. (Display case needs a total of two air connectors 1 per unit) Parallel Both machines are connected to the display case same way as single machine. (Display case needs a total of 4 air connectors 2 per unit) Both machines need to be connected together using standard Ethernet cable. Connector is located on the back wall of the machine and is marked as NETWORK. ONLY MASTER UNIT NEEDS SENSOR CONNECTED. 11
12 SLAVE MASTER PMCG - MANUAL 1. Master unit needs to be reprogrammed as follows: Parameter Value to be set Factory set value Notes This number must be same as parameter Adr on slave unit Slave unit(s) needs to be reprogramed as follows: Parameter Value to be set Factory set value Notes No change to factory set 0 0 No change to factory set 1 0 When the controller displays S the machine is working as a full slave unit. In this mode, both machines are controlled by master unit. PLEASE SEE PROGRAMMING CHAPTER FOR EXACT INSTRUCTION HOW TO ENTER PROGRAMMING MODE. 12
13 PROGRAMMING MANUAL USER MODE Shows actual RH value measured by machine sensor RH-measured humidity-read only SET-target humidity Target RH value. INCREASE/DECREASE VALUE ALA-out of range alarm Value offset for OUT OF RANGE ALARM. Alarm will be trigered when RH>(SET+ALA) and/or when RH<(SET-ALA) INCREASE/DECREASE VALUE 13
14 PROGRAMMING MODE Under normal circumstances, there is no need to make any changes to this portion of the controller software. Please be careful before making any changes. Please contact for help. Entering programming mode Hold 2 buttons about 3 sec SELECTING PARAMETERS MOVE THROUGH PARAMETERS LIST BACK TO USER MODE EDIT PARAMETER EDITING PARAMETER INCREASE/DECREASE VALUE BACK TO PARAMETER SELECT WITHOUT SAVING VALUE SAVE VALUE AND BACK TO PARAMETER SELECT 14
15 PARAMETERS LIST Measured Temperature READ ONLY Measured HumidityREAD ONLY Same as "RH" in user mode Humidity preset (target humidity) same as "SET" in user mode Out Of Range alarm offset same as "ALA" in user mode Calibration data 1 lower number noted on RH sensor label. (only for replacement sensors) Calibration data 2 higher number noted on RH sensor label. (only for replacement sensors) Control Mode 1- DH 2- DD 3- HH Calibration Offset Can be set to minimise difference between machine reading and third party probe. Network Address Logging interval in minutes 0=logger is off Entering Setting Time mode See next page for more info Value: 0 or 1 Sets Master mode. See Operation Manual: Master Slave Configuration Value: 0-99 Sets Master mode. See Operation Manual: Master Slave Configuration Value : 0 or 1 Sets Slave mode See Operation Manual: Master Slave Configuration THIS PARAMETER MUST BE SET ACCORDING TO THE MODEL, PRINTED ON THE BACK WALL OF THE MACHINE. Software version READ ONLY 15
16 SETTING DATE/TIME MODE for models with SD Logger ENTERING PROGRAMMING MODE PARAMETER SELECT MOVE THROUGH PARAMETERS LIST BACK TO PROGRAMMING MODE EDIT PARAMETER OR if "SET" parameter selected sets TIME/DATE and goes back to programming mode EDIT PARAMETER INCREASE/DECREASE VALUE BACK TO PARAMETER SELECTION WITHOUT SAVING BACK TO PARAMETER SELECTION 16
17 DATE/TIME PARAMETERS LIST YEAR MONTH DAY HOUR MINUTES SAVES ALL SET PARAMETERS 17
18 Network connection. For network connection and setup, please consult our Network Manual available from our download page. Shipping and storage. Product should be stored in clean area with temperature between 5 C 30 C and relative humidity below 80%. All cables, hoses and attachments must be disconnected and machine should be placed within a clear plastic bag. If shipping is necessary, original packing is the best solution. Otherwise, machine must be shipped in a box properly cushioned with bubble foil, styrofoam chips or other packing material preventing physical damage to the machine case. 18
19 LIMITED MICROCLIMATE GENERATOR WARRANTY This quality product is warranted to be free from manufacturer's defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer, and in accordance with the Requirements for Proper Operation as outlined in this Installation and Operating Manual. This warranty is available only to the client to whom the unit was originally sold by authorized distributor of Preservatech Inc or Preservatech Europe sp z o.o.., and is non-transferable. TERMS OF WARRANTY During the first two years, any electrical parts of this product found to be defective, including any sealed system units, will be repaired or replaced, at warrantor's option, at no charge to the ORIGINAL purchaser. To obtain service, contact Preservatech at the address below, who will provide you with instructions. Service must be performed by a qualified service technician, or with the express permission of Preservatech If service is performed on the units by anyone other than an authorized service depot or agent, all obligations of Preservatech under this warranty shall be at an end. EXCLUSIONS Save as herein provided by Preservatech, there are no other warranties, conditions, representations or guarantees, express or implied, made or intended by Preservatech or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Preservatech shall not be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and save harmless Preservatech from any claim for damages to persons or property caused by the unit. GENERAL PROVISIONS No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following: 1) Damage in transit or when moving the appliance. 2) Improper power supply such as low voltage, power surges, defective wiring or inadequate fuses. 4) Accident, alteration, abuse or misuse of the appliance such as an inadequate supply of cooling air, or abnormal operating conditions. 5) Use of a unit that has been optimized for a particular application in another application that has not been approved by Preservatech 6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc, 7) Service calls resulting in customer education. WARRANTY SERVICE Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present a facsimile of the cover of this document to our AUTHORIZED SERVICE DEPOT. Please contact our head office for service instructions. info@preservatech.com 19
20 Declaration of Conformity DECLARATION OF CONFORMITY Product: PMCG Humidity Generator Models: PMCG DH, PMCG-DD, PMCG-HH Description: Constant humidity generator designed for controlling relative humidity inside a museum display cases. Manufacturer: Preservatech Europe sp z o.o. Rowna 1, Bydgoszcz Country of origin: Poland The above mentioned product complies with following regulation: EU Low Voltage Directive 2006/95/EC EU Electromagnetic Compatibility Directive 2004/108/EC Harmonised Standards: EN : A2:2008, EN : A1: 2011, EN : 2007 Signed DEC 11, 2015 in Bydgoszcz Jan Maternicki president 20
PMCG II - MANUAL PMCG ORIGINAL INSTRUCTIONS. Preservatech Europe sp z o.o. Równa 1, Bydgoszcz, Poland
PMCG ORIGINAL INSTRUCTIONS Manufactured: Designed: Preservatech Europe sp z o.o. Równa 1, 85-846 Bydgoszcz, Poland info@preservatech.eu Preservatech Inc Toronto, Canada info@preservatech.com 1 www.preservatech.com
More informationRówna 1, Bydgoszcz, Poland This Manual covers the operation of Preservatech s network hardware and software.
NETWORK ORIGINAL INSTRUCTIONS Manufacturer: Design: Preservatech Europe sp z o.o. Równa 1, 85-846 Bydgoszcz, Poland www.preservatech.com Preservatech Inc Canada www.preservatech.com This Manual covers
More informationAutomated Tuner System Power Distribution Hub
User Guide Automated Tuner System Power Distribution Hub Model MT1020B MT1020-340 (Rev B) 12/11 User Guide Automated Tuner System Power Distribution Hub Model MT1020B 2900 Inland Empire Boulevard Ontario,
More informationSP-1009D. 1x9 Dual Link DVI Distribution Amplifier. User Manual. Made in Taiwan
SP-1009D 1x9 Dual Link DVI Distribution Amplifier User Manual Made in Taiwan Safety and Notice The SP-1009D 1x9 Dual Link DVI Distribution Amplifier has been tested for conformance to safety regulations
More informationModel P4017 Single Channel USB Oscilloscope. Quick Start Guide
Model P4017 Single Channel USB Oscilloscope Quick Start Guide General Warranty BNC warrants that the product will be free from defects in materials and workmanship for 3 years from the date of purchase
More informationGlobal Water Instrumentation, Inc.
Instrumentation, Inc. 11390 Amalgam Way Gold River, CA 95670 T: 800-876-1172 Int l: (916) 638-3429, F: (916) 638-3270 Display: EZ100 11/12/04-1 - Congratulations on your purchase of the EZ100 Display.
More informationKramer Electronics, Ltd. USER MANUAL. Models: RC-2C, Wall Plate / RS-232 / IR Controller RC-2, Wall Plate / RS-232 Controller
Kramer Electronics, Ltd. USER MANUAL Models: RC-2C, Wall Plate / RS-232 / IR Controller RC-2, Wall Plate / RS-232 Controller Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Your RC-2C/RC-2
More informationCrystalView DVI Multi INSTALLATION AND OPERATIONS MANUAL Stancliff Road Phone: (281)
CrystalView DVI Multi INSTALLATION AND OPERATIONS MANUAL 10707 Stancliff Road Phone: (281) 933-7673 Houston, Texas 77099 WWW.ROSE.COM LIMITED WARRANTY Rose Electronics warrants the CrystalView Multi to
More informationKramer Electronics, Ltd. USER MANUAL. Model: RC-BT1 / BT-1. Bluetooth controller
Kramer Electronics, Ltd. USER MANUAL Model: RC-BT1 / BT-1 Bluetooth controller Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 1 3.1 Your BT-1 Bluetooth controller 2 4 Using the Bluetooth
More informationRТTH DUAL ROOM SWITCH
DUAL ROOM SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA
More informationRTT2 ROOM TEMPERATURE SWITCH. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA STANDARDS OPERATIONAL DIAGRAMS WIRING AND CONNECTIONS
More informationDSTHM-2 COMBINED T AND RH DUCT TRANSMITTER. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 4 OPERATIONAL DIAGRAMS 5 WIRING AND
More information1x4 Splitter HDMI Distribution Amplifier with 4K2K & HDCP Support
1x4 Splitter HDMI Distribution Amplifier with 4K2K & HDCP Support User s Guide Models PT-SP-HD14-4K Designed in Germany Made in Taiwan 2010 PureLink GmbH All rights reserved. www.purelink.de 1 Table of
More informationSATA II HDD Canister KISS DA 435 Quick Reference Guide
SATA II HDD Canister KISS DA 435 Quick Reference Guide If it s embedded, it s Kontron 1. Table of Contents SATA II HDD Canister KISS DA 435 1. Table of Contents 1. Table of Contents... 1 2. Important Information...
More information3-4 SAS/SATA II HDD Canister Entry version USER S MANUAL XC-34D1-SA10-0-R. Document number: MAN A
3-4 SAS/SATA II HDD Canister Entry version XC-34D1-SA10-0-R USER S MANUAL Document number: MAN-00077-A ii Preface Important Information Warranty Our product is warranted against defects in materials and
More informationKramer Electronics, Ltd. USER MANUAL. Model: RC-52N. Room Controller
Kramer Electronics, Ltd. USER MANUAL Model: RC-52N Room Controller Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 2 4 Your RC-52N 3 4.1 The RC-52N Front Panel 3 4.2 The RC-52N Rear Panel
More informationTR100-A / TR200-A. Temperature / Humidity Data Loggers. Users Manual. For detailed specifications and ordering info go to
TR100-A / TR200-A Temperature / Humidity Data Loggers Users Manual For detailed specifications and ordering info go to www.testequipmentdepot.com TR100-A / TR200-A Temperature / Humidity Data Loggers English
More informationManual Guide PT-SP-HD18-4K. Manual Guide. 1x8 HDMI Distribution Amplifier with 4K2K & HDCP Support. Model PT-SP-HD18-4K. Designed in Germany
Manual Guide 1x8 HDMI Distribution Amplifier with 4K2K & HDCP Support Model Designed in Germany 2015 PureLink GmbH All rights reserved. Table of Contents Section 1: Getting Started... 2 1.1 Safety and
More informationUser Manual rev: Made in Taiwan
SP-5002P3 HDMI 1.4 1x2 HDMI Splitter User Manual rev: 130130 Made in Taiwan The SP-5002P3 HDMI 1.4 1x2 HDMI Splitter has been tested for conformance to safety regulations and requirements, and has been
More informationUser Manual HDM-IPBX-003C. Smar t Controller for HDMI over IP series. rev: Made in Taiwan
User Manual HDM-IPBX-003C Smar t Controller for HDMI over IP series rev: 170517 Made in Taiwan Safety and Notice The HDM-IPBX-003C Smart Controller for HDMI over IP series has been tested for conformance
More informationCV-24D. Stereo to SPDIF Converter with Adjustable Audio Delay. User Manual. Made in Taiwan
CV-24D Stereo to SPDIF Converter with Adjustable Audio Delay User Manual Made in Taiwan Safety and Notice The CV-24D Stereo to S/PDIF Converter with Adjustable Audio Delay has been tested for conformance
More informationK x2 HDMI 2.0a Splitter with Built-in & User Adjustable EDID Management. User Manual. rev: Made in Taiwan
K5702 1x2 HDMI 2.0a Splitter with Built-in & User Adjustable EDID Management User Manual rev: 170203 Made in Taiwan Safety and Notice The K5702 1x2 HDMI 2.0a Splitter with Built-in & User Adjustable EDID
More informationBroadband Automatic Disconnect Switch. User Manual
Reset/Test Primary/ Primary Broadband Automatic Disconnect Switch User Manual Local Power Remote Pwer Local 63V Fault Secondary Select Secondary 220V Normal 990-1929 09/2004 Introduction Introduction
More informationCablesson HDelity 1x4 Splitter with 4K2K and ARC. User Manual
Cablesson HDelity 1x4 Splitter with 4K2K and ARC User Manual All rights reserved - CABLESSON All rights reserved - CABLESSON ! SAFETY AND NOTICE TABLE OF CONTENT The Cablesson HDelity 1x4 HDMI Splitter
More informationCV-505ZA. HDMI 2.0a Audio Extractor & Embedder. User Manual. rev: Made in Taiwan
CV-505ZA HDMI 2.0a Audio Extractor & Embedder User Manual rev: 160825 Made in Taiwan Safety and Notice The CV-505ZA HDMI 2.0a Audio Extractor & Embedder has been tested for conformance to safety regulations
More informationUser's Guide. Model High Precision Quad Output DC Power Supply
User's Guide Model 382270 High Precision Quad Output DC Power Supply Introduction Congratulations on your purchase of the Extech 382270 DC Power Supply. The Model 382270 can be used for many applications
More informationUser Manual CV-87K. PS/2 extender over cat.x. rev: Made in Taiwan
User Manual CV-87K PS/2 extender over cat.x rev: 110929 Made in Taiwan Safety and Notice The CV-87K PS/2 extender over cat.x has been tested for conformance to safety regulations and requirements, and
More informationI/O Expansion Box Installation & Operator s Instruction Manual
I/O Expansion Box Installation & Operator s Instruction Manual May 2004 CTB Inc. Warranty I/O Expansion Box CTB Inc. Warranty CTB Inc. warrants each new Chore-Tronics product manufactured by it to be free
More informationRST ROOM TEMPERATURE TRANSMITTER. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 4 OPERATIONAL DIAGRAM 5 WIRING AND
More informationUser Manual rev: Made in Taiwan
SP-1014 1x4 DVI Splitter over Single Cat.X with HDCP Support User Manual rev: 111209 Made in Taiwan The SP-1014 1x4 DVI Splitter over Single Cat.X with HDCP Support has been tested for conformance to safety
More informationUSB Audio Converter. Installation and Operation Manual. USB to Analog Audio Converter Stancliff Road Houston, Texas 77099
USB Audio Converter USB to Analog Audio Converter Installation and Operation Manual 10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 techsupport@rose.com LIMITED WARRANTY Rose Electronics
More informationUser s Guide. OM-CP-PRHTEMP2000 Pressure, Humidity and Temperature Data Logger with LCD
User s Guide OM-CP-PRHTEMP2000 Pressure, Humidity and Temperature Data Logger with LCD OM-CP-PRHTEMP2000 Product Overview The OM-CP-PRHTEMP2000 is a pressure, temperature and humidity data logger with
More informationInstruction and Operation Manual
SEC IR PC LINK Instruction and Operation Manual Sensor Electronics Corporation 5500 Lincoln Drive Minneapolis, Minnesota 55436 USA (952) 938-9486 Fax (952) 938-9617 email sensor@minn.net or www.sensorelectronics.com
More informationKramer Electronics, Ltd. USER MANUAL
Kramer Electronics, Ltd. USER MANUAL Models: VP-200NK, 1:2 High Resolution XGA DA VP-300NK, 1:3 High Resolution XGA DA VP-400NK, 1:4 High Resolution XGA DA Contents Contents 1 Introduction 1 2 Getting
More informationSonic Ruptor 400. User Manual
Sonic Ruptor 400 User Manual Data herein has been verified and validated. It is believed adequate for the intended use of the instrument. If the instrument or procedures are used for purposes over and
More informationXBDM. 1015LV, 1020LV, 1030LV, 1020HV Models USER & INSTALLATION MANUAL BYPASS DISTRIBUTION MODULE
XBDM 1015LV, 1020LV, 1030LV, 1020HV Models USER & INSTALLATION MANUAL www.xpcc.com 2013 Xtreme Power Conversion Corporation. All rights reserved. Table of Contents IMPORTANT SAFETY INSTRUCTIONS:... 4 INTRODUCTION...
More informationUser Manual. HDMI tool DAH-HDMI K2K. 1 x 4 HDMI Splitter with EDID Management
User Manual DAH-HDMI 1-4 - 4K2K HDMI tool 1 x 4 HDMI Splitter with EDID Management SAFETY AND NOTICE The DAH-HDMI1-4-4K2K Splitter with EDID Management has been tested for conformance to safety regulations
More informationVSD-1MC MANUAL 0-10V / 4-20mA Variable Speed Module with Manual Override
MANUAL 0-10V / 4-20mA Variable Speed Module with Manual Override Varifan 3 4 5 6 7 MANUAL 2 8 1 OFF 10 9 AUTO MANUAL SPEED Installation / User s Guide This guide will inform the electrician on proper wiring
More informationKramer Electronics, Ltd.
Kramer Electronics, Ltd. Preliminary USER MANUAL Model: SL-1 Master Room Controller Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Your SL-1 Master Room Controller
More informationUser Manual AIMB-C200. Economical Embedded Chassis for Mini-ITX Motherboard
User Manual AIMB-C200 Economical Embedded Chassis for Mini-ITX Motherboard Copyright The documentation and the software included with this product are copyrighted 2010 by Advantech Co., Ltd. All rights
More informationSP x4 DVI over Single CAT5 Distribution Amplifier. User Manual. Made in Taiwan
SP-1014 1x4 DVI over Single CAT5 Distribution Amplifier User Manual Made in Taiwan Safety and Notice The SP-1014 1x4 DVI over Single CAT5 Distribution Amplifier has been tested for conformance to safety
More informationUser Manual SP-5028E. 2x8 HDMI Splitter 7.1 CH AUDIO. rev: Made in Taiwan
User Manual SP-5028E 2x8 HDMI Splitter To avoid EMI issue, complete STP Cat6 cable is strongly recommended! 7.1 CH AUDIO rev: 110225 Made in Taiwan Safety and Notice The SP-5028E 2x8 HDMI Splitter has
More informationMX User Manual. Dual-View Video Processor. rev: Made in Taiwan
MX-5022 Dual-View Video Processor User Manual rev: 151210 Made in Taiwan Safety and Notice The MX-5022 Dual-View Video Processor has been tested for conformance to safety regulations and requirements,
More informationInstallation Manual. 12 Volt Power Supplies. 18-Port. 9-Port RET18PT RET9PT
12 Volt Power Supplies Installation Manual 9-Port RET9PT 18-Port RET18PT INTRODUCTION Congratulations! The RET9PT 9-Port 12V Power Supply is the perfect solution for your larger security installations.
More informationRXTH DUAL ROOM SENSOR / SWITCH
DUAL ROOM SENSOR / SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE
More informationUSER MANUAL. Kramer Electronics, Ltd. Models:
Kramer Electronics, Ltd. USER MANUAL Models: VM-10FW, 1:10 FireWire Distributor/Hub VM-15FW, 1:15 FireWire Distributor/Hub VM-20FW, 1:20 FireWire Distributor/Hub Contents Contents 1 Introduction 1 2 Getting
More informationAC4G-D User s Manual
AC4G-D User s Manual Entire contents of this manual 2004 Active Cool Ltd. Ashkelon, Israel. Reproduction in whole or in part without permission is prohibited. Active Cool and AC4G-D are registered of Active
More informationInstruction Manual RS-1660
Instruction Manual RS-1660 Transformer Turns Ratio Meter This unit passes the following tests: Safety Symbols EN 61010-1: 2010 EN 61010-2-030: 2010 CAT IV 50V Pollution Degree 2 EN 61326-1: 2013 (CISPR
More informationwww.iconnectivity.com USER GUIDE WARRANTY INFORMATION iconnectivity warrants to the original purchaser that this unit is free of defects in materials and workmanship under normal use and maintenance for
More informationKramer Electronics, Ltd. USER MANUAL. Model: VP-200XLN. XGA Line Amplifier / DA
Kramer Electronics, Ltd. USER MANUAL Model: VP-200XLN XGA Line Amplifier / DA Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your VP-200XLN XGA Line Amplifier /
More informationMP3 Speaker USER GUIDE
MP3 Speaker USER GUIDE Jazwares, Inc. 2012 CONTENTS Please read the instructions along with the Speaker carefully before you use it, so that you can operate it conveniently. WELCOME, Warnings & Safety
More informationMFJ ENTERPRISES, INC.
Model MFJ-1142 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION
More informationMCS-Spectrum. Tactile Colorist Control Surface. Users Manual
MCS-Spectrum Tactile Colorist Control Surface Users Manual MCS-Spectrum, MCS-3800, MCS-3400 and MCS-3000 are trademarks of JLCooper Electronics. All other brand names are the property of their respective
More informationDebitek Card Revalue Station Installation Manual
Page 1 of 5 Debitek Card Revalue Station Installation Manual General Description The Debitek Card Revalue Station family includes the Cash to Card, Cash to Card with Dispenser, Automatic Debit Machine,
More informationKodiak Mobile INTELLIGENT DOCKING STATION USERS MANUAL PART NUMBER: PANASONIC CF53 TOUGHBOOK COMPATIBLE AN ISO 9001:2008 CERTIFIED COMPANY
CUSTOMER SERVICE If you have any questions or require additional information please contact Customer Service at 877-455-6886, Monday though Friday, 8:00am - 5:00pm CST. TECHNICAL SUPPORT Kodiak Mobile
More informationBefore switching on please remove all packaging materials and boxes then set
Before switching on please remove all packaging materials and boxes then set the refrigerator in a position with the front tilted slightly higher - You can make adjustments via the levelling screws on
More informationDon t plug me in just yet.
Easy Transfer Cable for Windows 7 Don t plug me in just yet. We need to do a few things first to get your computers ready to transfer your files and user accounts. Quick Start Guide F5U279 i 1 Prepare
More information60M HDMI+USB KVM Extender
60M HDMI+USB KVM Extender Operating Instructions Dear Customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating
More informationBluetooth USB Adapter TALUS. User Guide
Bluetooth USB Adapter TALUS User Guide Revision 0.1 1 User Guide for the TALUS Revision 1.0.1 Firmware version 1.0.X Printed in Korea Copyright Copyright 2008, SystemBase Co., Ltd. All rights reserved.
More informationCO2 Controller Operating Instructions Models: RAD-0501, RAD-0501A, RAD-0501E 1. Product Description
CO2 Controller Operating Instructions Models: RAD-0501, RAD-0501A, RAD-0501E 1. Product Description RAD-0501 Greenhouse Mode: Controls CO2 generator or regulator to increase CO2 levels during daylight
More informationMODBUS MANUAL For the AccUView UV Transmission Monitor
MODBUS MANUAL For the AccUView UV Transmission Monitor HF scientific, inc. 3170 Metro Parkway Ft. Myers, FL 33916 Phone: 239-337-2116 Fax: 239-332-7643 E-Mail: info@hfscientific.com Website: www.hfscientific.com
More information1x8 HDMI Splitter Over Single Cat5e/6 Cable. Up to 50M with IR. Notice. Features. Package Contents. Operating Instructions
1x8 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR Operating Instructions Notice The information in this document is subject to change without notice. Every effort has been made in the preparation
More informationma Input Module. Installation and Operation Guide
780 4-20 ma Input Module Installation and Operation Guide Part #60-9003-064 Copyright 1995. All rights reserved, Isco, Inc. Revision E, April 20, 2011 Foreword This instruction manual is designed to help
More informationVP Process Inc. Model: VP-EC-RDU Modbus RTU LCD Display
VP Process Inc. Model: Modbus RTU LCD Display User Manual Ver: 2.0 Aug. 2017 P a g e 1 Standard Features Low Power (12-24 VDC) 2.1 x 5mm Barrel Plug, RJ45 and Terminal Block Input On-Board Local Temperature
More informationOperating Instructions
Model No.: SP0108-U01 Operating Instructions Thanks for purchasing our product. Please be sure to read this instruction manual Carefully before using our product. Introduction Vision HD s SP0108-U01 is
More informationMicro-Ohmmeter Model 6292
Micro-Ohmmeter Model 6292 Quick Start Guide ENGLISH www.aemc.com CHAUVIN ARNOUX GROUP Statement of Compliance Chauvin Arnoux, Inc. d.b.a. AEMC Instruments certifies that this instrument has been calibrated
More informationUser Manual TLS HDMI Switch Splitter 3/2
875224 User Manual TLS HDMI Switch Splitter 3/2 IR SW B A 3 2 1 HDMI IN HDMI OUT DC 5V 1 2 3 A B 8 875224 HDMI Switch Splitter 3/2 Thank you for purchasing this product. For optimum performance and safety,
More informationE2K-F. Flat Capacitive Sensor with a Thickness of Only 10 mm. Flat Proximity Sensor. Ordering Information. Sensors [Refer to Dimensions on page 4.
Flat Proximity Sensor EK-F CSM_EK-F_DS_E Flat Capacitive Sensor with a Thickness of Only mm Flat Sensor with excellent space efficiency. (Model with built-in Amplifier is only mm thick.) Direct mounting
More informationRXTP ROOM TEMPERATURE
ROOM TEMPERATURE CONTROLLER WITH PI CONTROL Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4
More informationPRO-HDRsplit4P 4K HDR 1x4 splitter. User s Guide. Made in Taiwan
PRO-HDRsplit4P 4K HDR 1x4 splitter User s Guide Made in Taiwan Congratulations for owning a gofanco product. Our products aim to meet all your connectivity needs wherever you go. Have fun with our products!
More informationSM-10 SM-20-A. Sound Level Meters. Users Manual. For detailed specifications and ordering info go to
SM-10 SM-20-A Sound Level Meters Users Manual For detailed specifications and ordering info go to www.testequipmentdepot.com SM-10 / SM-20-A Sound Level Meters English Users Manual SM10_Rev002 2009 Amprobe
More information1x2 HDMI Splitter over Cat.X with HDBaseT-Lite, 4K2K, IR & RS-232
SP-5012V 1x2 HDMI Splitter over Cat.X with HDBaseT-Lite, 4K2K, IR & RS-232 User Manual rev: 140806 Made in Taiwan Safety and Notice The SP-5012V 1x2 HDMI Splitter over Cat.X with HDBaseT-Lite, 4K2K, IR
More informationwww.iconnectivity.com USER GUIDE WARRANTY INFORMATION iconnectivity warrants to the original purchaser that this unit is free of defects in materials and workmanship under normal use and maintenance for
More informationWCC100 IN-VEHICLE CHARGING CRADLE OWNER S MANUAL
WCC100 IN-VEHICLE CHARGING CRADLE OWNER S MANUAL 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.indd 1 12/4/2013 10:38:04 AM 128-9237B WCC100 In-Vehicle Charging Cradle 12 03 13.indd 2 12/4/2013
More informationKramer Electronics, Ltd. USER MANUAL. Model: VM-50AN. 1:5 Audio Distributor
Kramer Electronics, Ltd. USER MANUAL Model: VM-50AN 1:5 Audio Distributor Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your Audio VM-50AN 1:5 Distributor 4 5
More informationFNet Repeater Installation & Operator s Instruction Manual
FNet Repeater Installation & Operator s Instruction Manual October 2004 CTB Inc. Warranty FNet Repeater CTB Inc. Warranty CTB Inc. warrants each new Chore-Tronics product manufactured by it to be free
More informationMiniModules. Reference Manual. Series R CT 3002 V 1.0 MiniModule USB Service Adapter and Software
Reference Manual R CT 3002 V 1.0 MiniModule USB Service Adapter and Software Series 3000 MiniModules LYNX Technik AG Brunnenweg 3 64331 Weiterstadt Germany www.lynx-technik.com Information in this document
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationBRIGHTLINK 1x8 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR MODEL: BL-SPL1X8-CAT
BRIGHTLINK 1x8 HDMI Splitter Over Single Cat5e/6 Cable Up to 50M with IR MODEL: BL-SPL1X8-CAT Notice The information in this document is subject to change without notice. Every effort has been made in
More informationMFJ ENTERPRISES, INC.
Model MFJ-1163 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION
More informationPure Sinewave Inverter
SINEWAVE INVERTER Pure Sinewave Inverter Model No. PST-25S-12E PST-25S-24E Manual Please read this manual before operating your inverter Notice of Copyright PST-255 inverter owner s manual 2004-2015 Samlex
More informationETConcept Systems Engineering. User s Guide
Wiegand to RS485 Converter User s Guide Nov-08 Copyright 2008. All rights reserved including the right of reproduction in whole or in part in any form. Contents List of Accessories Included... 1 List
More informationMX-5004MZ. User Manual. 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4. rev: Made in Taiwan
MX-5004MZ 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4 User Manual rev: 160318 Made in Taiwan Safety and Notice The MX-5004MZ 4x1 HDMI 2.0a Quad-View Video Processor with 4K2K60 4:4:4 has
More informationStart Here. All-in-One Printer. Print Copy Scan
Start Here All-in-One Printer Print Copy Scan Note: A USB 2.0 cable is required to connect your Kodak All-in-One printer to your Windows or Macintosh OS computer. Available in the Kodak online store or
More informationChroma-Q Color Web PSU 10-DMX. User Manual
Chroma-Q Color Web PSU 10-DMX User Manual Version 1.1 September 2012 Warranty Statement Chroma-Q warrants to the original purchaser, with proof of purchase, that its delivered products shall be free from
More informationKramer Electronics, Ltd. USER MANUAL. Model: VS-4x4FW. 4x4 FireWire Switcher
Kramer Electronics, Ltd. USER MANUAL Model: VS-4x4FW 4x4 FireWire Switcher Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 1 3 Overview 3 4 Your FireWire Switcher 4 5 Using the FireWire
More informationChapter 1 : FCC Radiation Norm...3. Chapter 2 : Package Contents...4. Chapter 3 : System Requirements...5. Chapter 4 : Hardware Description...
Table of Contents Chapter 1 : FCC Radiation Norm...3 Chapter 2 : Package Contents...4 Chapter 3 : System Requirements...5 Chapter 4 : Hardware Description...6 Chapter 5 : Charging Your Keychain...7 Chapter
More informationOperating Bulletin MODBUS-RTU. The Fastest Flow Controller Company in the World!
Operating Bulletin MODBUS-RTU The Fastest Flow Controller Company in the World! 1 Notice: Alicat Scientific, Inc. reserves the right to make any changes and improvements to the products described in this
More informationUser's Guide. Extech AM A AC Analog Clamp Meter
User's Guide Extech AM300 300A AC Analog Clamp Meter Introduction Congratulations on your purchase of the Extech AM300 Analog Clamp Meter. This device measure AC Voltage and Current, DC Voltage, and Resistance.
More informationKramer Electronics, Ltd. USER MANUAL. Model: WP-210E. XGA Line Driver
Kramer Electronics, Ltd. USER MANUAL Model: WP-210E XGA Line Driver Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 1 4 Your WP-210E XGA Line Driver 2 4.1 Your WP-210E: Available in 3
More information4-20mA Display. Installation and Operation Manual. Rev 4/3/2019 Part #
4-20mA Display Installation and Operation Manual Rev 4/3/2019 Part # 12050769 Table of Contents DOCUMENTATION CONVENTIONS... 2 Section 1: System Description... 3 Function and Theory... 3 Section 2: System
More informationMini-DVI-WP Series WALL PLATE MINIATURE MULTIMODE FIBER OPTIC DVI TRANSMISSION SYSTEM
Mini-DVI-WP Series WALL PLATE MINIATURE MULTIMODE FIBER OPTIC DVI TRANSMISSION SYSTEM BCI reserves the right to make changes to the products described herein without prior notice or consent. No liability
More informationOperating Instructions
Model No.: VH0101 Operating Instructions Thanks for purchasing our product. Please be sure to read this instruction manual carefully before using our product. Introduction VH0101 is a VGA video converter.
More informationzclock-200w User Manual
zclock-200w User Manual Table of contents Product Diagram......Page 1 Alarm clock operation......page 5 Setting up Hidden Cam.....Page 7 Advanced set up......page 14 Windows......Page 15 Apple OSX...Page
More informationPUSH-TO-TALK USER GUIDE
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
More informationOZONE SWITCH Model OS-6. OS-6 Features
USER MANUAL OZONE SWITCH Model OS-6 OS-6 Features The OS-6 is an industrial grade ozone controller and monitor. The OS-6 design is optimized for accuracy and ease of installation, setup and operation.
More informationDX-C USER GUIDE
PC/Mac USB File Transfer Adapter DX-C114200 USER GUIDE 2 3 Dynex DX-C114200 PC/Mac USB File Transfer Adapter Contents Important safety instructions...3 Introduction...4 Features...5 Package Contents...5
More informationKramer Electronics, Ltd.
Kramer Electronics, Ltd. Preliminary USER MANUAL Model: SL-12 Master Room Controller Contents Contents 1 Introduction 1 2 Getting Started 1 2.1 Quick Start 2 3 Overview 3 4 Your SL-12 Master Room Controller
More informationKramer Electronics, Ltd. USER MANUAL. Model: VP-111. XGA Line Driver
Kramer Electronics, Ltd. USER MANUAL Model: VP-111 XGA Line Driver Contents Contents 1 Introduction 1 2 Getting Started 1 3 Overview 1 4 Your VP-111 XGA Line Driver 2 5 Connecting the VP-111 XGA Line Driver
More informationLED FOLDING WORKLIGHT TM
LED FOLDING WORKLIGHT TM LED LIGHT POWERSTRIP USB CHARGING ITM. / ART. 689211 Model: LM55812 CARE & USE INSTRUCTIONS IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY For assistance with assembly
More information