RX-6030VBK/RX-6032VSL RX-5030VBK/RX-5032VSL

Transcription

1 TA/NEWS/FO DISPLAY MODE STANDBY STANDBY/ON ON/OFF ON/OFF DIGITAL AUTO SPK 1 2 ONE TOUCH OPERATION BASS BOOST PUT ATT EON RDS SLEEP ANALOG L C R PRO LOGIC DSP H.PHONE AUTO MUTG TUNED STEREO TA NEWS FO VOLUME LEAR PCM S.WFR LFE DIGITAL LS S RS SOURCE NAME AUDIO/VIDEO CONTROL RECEIVER RX-6030VBK/RX-6032VSL RX-5030VBK/RX-5032VSL MASTER VOLUME RX 6030V AUDIO/VIDEO CONTROL RECEIVER DIMMER DSP PUT DIGITAL /DSP OFF CH PUT ANALOG PUT ATT MULTI TV SOUND CD TAPE/CDR FM AM SETTG MULTI JOG ADJUST PHONES DIGITAL PRO LOGIC SPEAKERS SUBWOOFER FM/AM TUNG FM/AM RESET FM MODE MEMORY SET EXIT STRUCTIONS For Customer Use: Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Model No. Serial No. LVT B [J]

2 Warnings, Cautions, and Others/ Mises en garde, précautions et indications diverses CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS SIDE. REFER SERVICG TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For U.S.A This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Changes or modifications not expressly approved by the manufacturer for compliance could void the user s authority to operate the equipment. WARNG: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RA OR MOISTURE. CAUTION To reduce the risk of electrical shocks, fire, etc.: 1. Do not remove screws, covers or cabinet. 2. Do not expose this appliance to rain or moisture. ATTENTION Afin d éviter tout risque d électrocution, d incendie, etc.: 1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l appareil. 2. Ne pas exposer l appareil à la pluie ni à l humidité. Caution STANDBY/ON button! Disconnect the mains plug to shut the power off completely. The STANDBY/ON button in any position does not disconnect the mains line. The power can be remote controlled. Attention Commutateur STANDBY/ON! Déconnecter la fiche de secteur pour couper complètement le courant. Le commutateur STANDBY/ON ne coupe jamais complètement la ligne de secteur, quelle que soit sa position. Le courant peut être télécommandé. For Canada/pour le Canada CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY SERT ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, TRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQUAU FOND THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET THE TERFERENCE-CAUSG EQUIPMENT STANDARD ENTITLED DIGITAL APPARATUS, ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS. CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR; APPAREILS NUMERIQUES, NMB-003 EDICTEE PAR LE MISTRE DES COMMUNICATIONS. This mark indicates that ONLY the remote control CAN be used for the operation explained. RX-6030V RX-6032V ONLY Features with this mark are provided ONLY for RX-6030VBK and RX-6032VSL. Remote NOT This mark indicates that the remote control CANNOT be used for the operation explained. Use the buttons on the front panel.

3 Table of Contents Table of Contents Parts Identification... 2 Getting Started... 5 Before Installation... 5 Checking the Supplied Accessories... 5 Connecting the AM and FM Antennas... 5 Connecting the Speakers and Subwoofer... 6 Connecting Audio/Video Components... 7 Analog Connections... 7 Digital Connections Connecting the Power Cord Putting Batteries in the Remote Control Basic Operations Turning On the Power Selecting the Source to Play Changing the Source Name Selecting Different Sources for Picture and Sound Adjusting the Volume Listening with Headphones Only Turning Off the Sound Temporarily Muting Changing the Display Brightness DIMMER Turning Off the Power with the Sleep Timer Basic Settings Basic Settings Using MULTI JOG Dial Setting the Speaker Information Selecting the Digital Input Terminals DIGITAL Selecting the Video Input Terminal VIDEO, VIDEO Selecting the Analog or Digital Input Mode Sound Adjustments Attenuating the Input Signal Turning Off the Subwoofer Reinforcing the Bass Sound Adjustments Using MULTI JOG Dial Sound Adjustments Using Remote Control Adjusting Speaker Output Levels Using Test Tone Adjusting Subwoofer Output Level Tuner Operations Tuning in to Stations Manually Using Preset Tuning To Store the Preset Stations To Tune in to a Preset Station Selecting the FM Reception Mode Creating Realistic Sound Fields Using Surround Modes Using DSP Modes Using MULTI Playback Mode (RX-6030VBK/RX-6032VSL only) Activating MULTI Playback Mode COMPU LK Remote Control System AV COMPU LK Remote Control System Operating JVC s Audio/Video Components Operating Audio Components Operating Video Components Operating Other Manufacturers Video Equipment Troubleshooting Specifications Differences between RX-6030VBK/RX-6032VSL and RX-5030VBK/RX-5032VSL Main unit : Supplied : Not supplied Color Video input terminals AV COMPU LK MULTI Bass boost function Selectable source RX-6030VBK Black Composite video AV COMPU LK III MULTI,,, S-video TV SOUND, CD, Component video TAPE/CDR, FM, AM RX-6032VSL RX-5030VBK RX-5032VSL Silver Black Silver Composite video S-video Component video Composite video Composite video AV COMPU LK III AV COMPU LK AV COMPU LK MULTI,,, TV SOUND, CD, TAPE/CDR, FM, AM,, TV SOUND, CD, TAPE/CDR, FM/AM,, TV SOUND, CD, TAPE/CDR, FM/AM Remote control unit RM-SRX6030J for RX-6030VBK RM-SRX6032J for RX-6032VSL RM-SRX5030J for RX-5030VBK/RX-5032VSL BASSBOOST button MULTI button 1

4 Parts Identification RX-6030VBK is mainly used for illustrations to explain the connections and operations throughout the instructions. Front Panel p MASTER VOLUME STANDBY RX 6030V AUDIO/VIDEO CONTROL RECEIVER DIMMER STANDBY/ON DSP PUT DIGITAL /DSP OFF PUT ANALOG PUT ATT SETTG MULTI JOG ADJUST PHONES DIGITAL PRO LOGIC SPEAKERS SUBWOOFER FM/AM TUNG FM/AM PRESET FM MODE MEMORY SET EXIT ON/OFF ON/OFF q w e r t y u i o ; a s d RX-6030VBK/RX-6032VSL MULTI TV SOUND CD TAPE/CDR FM AM SOURCE NAME f RX-5030VBK/RX-5032VSL TV SOUND CD TAPE/CDR FM/AM SOURCE NAME See pages in parentheses for details. 1 STANDBY/ON button and STANDBY lamp (11) 2 /DSP OFF button (26, 27) 3 DSP button (27) 4 button (26) 5 Remote sensor (10) 6 Display (For details, see Display on the next page.) 7 PUT ANALOG button (17) PUT ATT button (18) 8 PUT DIGITAL button (17) 9 DIMMER button (13) p MASTER VOLUME control (13) q PHONES jack (13) w SPEAKERS ON/OFF button (13) e SUBWOOFER ON/OFF button (18) r FM/AM TUNG 5/ buttons (22) t FM/AM PRESET 5/ buttons (23) y FM MODE button (23) u MEMORY button (22, 23) i SETTG button (15) o SET button (15, 19) ; MULTI JOG dial (15, 19) a EXIT button (15, 19) s ADJUST button (19) d For RX-6030VBK and RX-6032VSL Source selection buttons (11) MULTI,,, TV SOUND, CD, TAPE/CDR, FM, AM SOURCE NAME button (12) f For RX-5030VBK and RX-5032VSL Source selection buttons (11),, TV SOUND, CD, TAPE/CDR, FM/AM SOURCE NAME button (12) 2

5 Parts Identification Display = # See pages in parentheses for details. 1 ANALOG indicator (17) 2 DIGITAL AUTO indicator (17) 3 SPK indicator (13) 4 Speaker indicators and signal indicators (27) 5 PRO LOGIC II indicator (24, 26) 6 DSP indicator (25, 27) 7 H.PHONE indicator (13) 8 RX-6030VBK and RX-6032VSL only: BASS BOOST indicator (18) $ 9 TUNED indicator (22) 0 PUT ATT indicator (18) - STEREO indicator (22) = AUTO MUTG indicator (23) ~ SLEEP indicator (14)! VOLUME indicator Digital signal format indicators (17) # CH indicator (22) $ Main display Remote Control TV TEST 1 4 MENU 7/P ENTER 10 CATV LEVEL RETURN TA/NEWS/FO 100 REW REC PAUSE A/V CONTROL RECEIVER FRONT L 2 CENTER 5 SURR L 8 0 FRONT R SUBWFR SURR R FM MODE DSP AUDIO TV/CATV SLEEP CD-DISC /DSP OFF DIMMER TV/VIDEO BASSBOOST MUTG CH TV/CATV CH TV VOLUME STANDBY/ON FF TAPE/CDR CD MULTI FM/AM TV SOUND ANALOG /DIGITAL VOLUME REMOTE CONTROL RM-SRX6030J = * # $ % ^ &* * ( Remote Control See pages in parentheses for details. 1 TV/CATV selector (35) 2 10 keys for selecting preset channels (23) 10 keys for sound adjustment (20, 21) 10 keys for operating audio/video components (32 36) 3 SOUND button (20, 21) 4 REC PAUSE button (33, 34) 5 Source selection buttons (11) TAPE/CDR, CD,, MULTI*, FM/AM, TV SOUND, 6 FM MODE button (23) 7 button (26) 8 DIMMER button (13) 9 TV/VIDEO button (34, 35) 0 CH +/ buttons (34, 36) - TV/CATV CH +/ buttons (34, 35) = STANDBY/ON buttons (11, 34 36) AUDIO, TV/CATV,, ~ SLEEP button (14)! Operating buttons for audio/video components 3, 8, 7, /4, FF/REW (33, 34, CD-DISC button (33) # ANALOG/DIGITAL button (17) $ /DSP OFF button (26, 27) % DSP button (27) ^ MUTG button (13) & BASSBOOST* button (18) * VOLUME +/ button (13) ( TV VOLUME +/ buttons (34, 35) * MULTI (source selection button) and BASSBOOST (&) buttons are NOT provided for RX-5030VBK and RX-5032VSL. 3

6 Parts Identification Rear Panel RX-6030VBK/RX-6032VSL DIGITAL 1 () AV COMPU LK-III MONITOR Y PB PR DIGITAL 2 ( CD ) DIGITAL CD (REC) TAPE /CDR (PLAY) (REC) FRONT SUB WOOFER RIGHT AUDIO COMPU LK-4 (SYNCHRO) LEFT CENTER MONITOR (REC) AM LOOP ANTENNA FM 75 COAXIAL CENTER SPEAKER SPEAKERS RIGHT LEFT FRONT SPEAKERS RIGHT LEFT CAUTION : SPEAKER IMPEDANCE 8 16 (PLAY) SURR (REAR) RIGHT LEFT (PLAY) AM EXT TV SOUND VIDEO S-VIDEO RIGHT LEFT AUDIO SUBWOOFER p q Rear Panel RX-5030VBK/RX-5032VSL DIGITAL 1 () AV COMPU LK DIGITAL 2 ( CD ) DIGITAL CD (REC) TAPE /CDR (PLAY) (REC) AUDIO RIGHT COMPU LK-4 (SYNCHRO) LEFT MONITOR (REC) AM LOOP ANTENNA FM 75 COAXIAL CENTER SPEAKER SPEAKERS RIGHT LEFT FRONT SPEAKERS RIGHT LEFT CAUTION : SPEAKER IMPEDANCE 8 16 (PLAY) RIGHT (PLAY) AM EXT TV SOUND RIGHT LEFT AUDIO SUBWOOFER p Rear Panel RX-6030VBK/RX-6032VSL See pages in parentheses for details. 1 DIGITAL terminals (10) Coaxial: DIGITAL 1 () Optical: DIGITAL 2 (CD) 2 Audio input/output terminals (6 9) Audio components: CD, TAPE/CDR Video components:, TV SOUND, SUBWOOFER 3 COMPU LK-4 terminals (29) 4 AV COMPU LK-III terminals (30) 5 FM/AM ANTENNA terminals (5) 6 COMPONENT VIDEO input/output terminals (8, 9) Input:, Output: MONITOR 7 S-VIDEO/VIDEO (composite video) input/output terminals (8, 9) Input:, Output: MONITOR, 8 CENTER SPEAKER terminals (6) 9 SPEAKERS terminals (6) p FRONT SPEAKERS terminals (6) q AC power cord (10) Rear Panel RX-5030VBK/RX-5032VSL See pages in parentheses for details. 1 DIGITAL terminals (10) Coaxial: DIGITAL 1 () Optical: DIGITAL 2 (CD) 2 Audio input/output terminals (6 9) Audio components: CD, TAPE/CDR Video components:, TV SOUND, SUBWOOFER 3 COMPU LK-4 terminals (29) 4 AV COMPU LK terminals (30) 5 FM/AM ANTENNA terminals (5) 6 VIDEO (composite video) input/output terminals (8, 9) Input:, Output: MONITOR, 7 CENTER SPEAKER terminals (6) 8 SPEAKERS terminals (6) 9 FRONT SPEAKERS terminals (6) p AC power cord (10) 4

7 Parts Identification/Getting Started Getting Started Before Installation General Precautions DO NOT insert any metal object into the unit. DO NOT disassemble the unit or remove screws, covers, or cabinet. DO NOT expose the unit to rain or moisture. Rear panel Locations Install the unit in a location that is level and protected from moisture. The temperature around the unit must be between 5 C and 35 C (23 F and 95 F). Make sure there is good ventilation around the unit. Poor ventilation could cause overheating and damage the unit. Handling the unit DO NOT touch the power cord with wet hands. DO NOT pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord. Keep the power cord away from the connecting cords and the antenna. The power cord may cause noise or screen interference. Coaxial cable is recommended for the antenna connection, since such cable is well-shielded against interference. When a power failure occurs, or when you unplug the power cord, the preset settings such as preset FM or AM channels and sound adjustments may be erased within a few days. Checking the Supplied Accessories Check to be sure you have all of the following supplied accessories. The number in parentheses indicates the quantity of each piece supplied. Remote control (1) Batteries (2) AM loop antenna (1) FM antenna (1) If anything is missing, contact your dealer immediately. AM LOOP FM 75 COAXIAL ANTENNA AM loop antenna (supplied) If FM reception is poor, connect an outdoor FM antenna. Standard type outdoor FM antenna (not supplied) FM 75 COAXIAL AM EXT 7 How to connect the AM antenna cord FM 75 COAXIAL FM antenna (supplied) Extend the supplied FM antenna horizontally. If AM reception is poor, connect outdoor single vinyl-covered wire (not supplied). Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. Connecting the AM and FM Antennas AM antenna connection Connect the supplied AM loop antenna to the AM LOOP terminals. Turn the loop until you have the best reception. If the reception is poor, connect an outdoor single vinylcovered wire (not supplied) to the AM EXT terminal. (Keep the AM loop antenna connected.) FM antenna connection Connect the supplied FM antenna to the FM 75 Ω COAXIAL terminal as a temporary measure. Extend the supplied FM antenna horizontally. If the reception is poor, connect an outdoor FM antenna (not supplied). Before attaching a 75 Ω antenna with a coaxial type connector, disconnect the supplied FM antenna. 1 Open the terminal. 2 Insert the AM antenna cord. 3 Close the terminal. Notes: If the AM loop antenna wire is covered with vinyl, remove the vinyl by twisting it as shown to the right. Make sure the antenna conductors do not touch any other terminals, connecting cords, or power cord. This could cause poor reception. 5

8 Getting Started Connecting the Speakers and Subwoofer 7 Speaker layout diagram You can connect five speakers a pair of front speakers, a center speaker, and a pair of surround speakers and a subwoofer. CAUTION: Use speakers with a SPEAKER IMPEDANCE as indicated by the speaker terminals. Left front speaker Center speaker Subwoofer Right front speaker 7 Connection diagram Left surround speaker Right surround speaker CENTER SPEAKER SPEAKERS RIGHT LEFT + + FRONT SPEAKERS RIGHT LEFT + CAUTION : SPEAKER IMPEDANCE 8 16 To left front speaker + To left surround speaker SUBWOOFER To subwoofer input Powered subwoofer To center speaker To right front speaker To right surround speaker 7 How to connect speaker cords For each speaker, connect the (+) and ( ) terminals on the rear panel to the (+) and ( ) terminals marked on the speakers Twist and remove the insulation at the end of each speaker cord. 2 Open the terminal (1), then insert the speaker cord (2). 3 Close the terminal How to connect the subwoofer Connect the input jack of a powered subwoofer to the SUBWOOFER jack on the rear panel, using a cable with RCA pin plugs (not supplied). Refer also to the manual supplied with your subwoofer. By connecting a subwoofer, you can enhance the bass or reproduce the original LFE signals recorded in the digital software. Since bass sound is non-directional, you can place a subwoofer wherever you like. Normally place it in front of you. After connecting the front, center, surround speakers and/ or a subwoofer, set the speaker setting information properly to obtain the best possible Surround effects with your listening conditions. For details, see pages 15 and 16. NO for the subwoofer, LARGE for the front speakers, and SMALL for the center and surround speakers are initial settings. 6

9 Getting Started Connecting Audio/Video Components Turn the power off to all components before making connections. You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components. Audio Components: CD player* and Cassette deck (or CD recorder*) Video Components:, TV*, and player* *You can connect these components using the methods described in Analog connections (below) and/or in Digital connections (see page 10). Analog Connections Audio component connections Use cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack and the red plug to the audio right jack. Rear panel CAUTION: If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted. L R CD (REC) TAPE /CDR (PLAY) L R L To audio output To audio input CD player To audio output (REC) (PLAY) TV SOUND RIGHT AUDIO LEFT R Cassette deck CD recorder You can connect either a cassette deck or a CD recorder to the TAPE/CDR jacks. When connecting a CD recorder to the TAPE/ CDR jacks, change the source name to CDR so that CDR appears on the display when selected as the source. See page 12 for details. If your audio components have a COMPU LK jack See also page 29 for detailed information about the connections with the COMPU LK remote control system. Video component connections Use cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack. To get better picture quality RX-6030VBK and RX-6032VSL have the following video terminals and you can use any of them to connect a video component: VIDEO (composite video) terminals S-VIDEO terminals COMPONENT VIDEO terminals RX-6030V RX-6032V ONLY If your video components have S-video (Y/C-separation) terminals, connect them using an S-video cable (not supplied). If your video components have component video (Y, PB, PR) terminals, connect them using a component video cable (not supplied). By using these terminals, you can get better picture quality in the order of Composite video < S-video < Component video. However, remember that the video signals from one type of input terminals are sent only through the video output terminals of the same type. Therefore, if a recording video component and a playing video component are connected to the receiver through different types of video terminals, you cannot record the picture from the playing component onto the recording component. In addition, if the TV and a playing video component are connected to the receiver through different types of video terminals, you cannot view the playback picture from the playing component on the TV. TO BE CONTUED TO THE NEXT PAGE 7

10 Getting Started Rear panel A B E F G C D Y PB PR MONITOR L R R L CD (REC) TAPE /CDR (PLAY) (REC) (PLAY) TV SOUND RIGHT AUDIO LEFT FRONT SUB WOOFER SURR (REAR) RIGHT RIGHT SUBWOOFER AUDIO LEFT CENTER LEFT VIDEO MONITOR (REC) (PLAY) S-VIDEO AM LOOP ANTENNA FM 75 COAXIAL AM EXT RX-6030V RX-6032V ONLY Å To left/right audio input ı To left/right audio output Ç To composite video output Î To composite video input RX-6030VBK and RX-6032VSL only To S-video input Ï To S-video output Ì To component video output TV TV B C D A RX-6030V RX-6032V ONLY Y PB PR MONITOR R L CD (REC) TAPE /CDR (PLAY) (REC) (PLAY) TV SOUND RIGHT AUDIO LEFT FRONT SUB WOOFER SURR (REAR) RIGHT RIGHT SUBWOOFER AUDIO LEFT CENTER LEFT VIDEO MONITOR (REC) (PLAY) S-VIDEO AM LOOP ANTENNA FM 75 COAXIAL AM EXT Å To audio output ı To composite video input RX-6030VBK and RX-6032VSL only Ç To S-video input Î To component video input 8

11 Getting Started RX-6030VBK/RX-6032VSL Å To surround left/right audio output ı To center audio output Ç To subwoofer audio output Î To front left/right audio output To composite video output Ï To S-video output Ì To component video output Rear panel A B C player F G D E Y PB PR FRONT SUB WOOFER SURR (REAR) RIGHT RIGHT SUBWOOFER AUDIO LEFT CENTER LEFT VIDEO MONITOR (REC) (PLAY) S-VIDEO AM LOOP ANTENNA FM 75 COAXIAL MONITOR To use software encoded with Dolby Digital or DTS Digital Surround, connect the player using one of AM the DIGITAL EXT terminals (see page 10). When you connect the player with stereo output jacks, connect using Î. When you connect the player with its analog discrete output (5.1 channel reproduction) jacks, connect using Å to Î (see Using MULTI Playback Mode on page 28). RX-5030VBK/RX-5032VSL player Rear panel A B R RIGHT LEFT MONITOR L AUDIO (REC) (PLAY) Å To audio output ı To composite video output To use software encoded with Dolby Digital or DTS Digital Surround, connect the player using one of the DIGITAL terminals (see page 10). 9

12 Getting Started Digital Connections This receiver is equipped with two DIGITAL terminals one digital coaxial terminal and one digital optical terminal. You can connect any component to one of the digital terminals using a digital coaxial cable (not supplied) or digital optical cable (not supplied). Connecting the Power Cord Before plugging the power cord into an AC outlet, make sure that all connections have been made. Plug the power cord into an AC outlet. Digital coaxial cable Digital optical cable IMPORTANT: When connecting a video component using the digital terminal, you also need to connect it to the video jack on the rear. Without connecting it to the video jack, you cannot view the playback picture. After connecting the components using the DIGITAL terminals, correctly set the following if necessary: Set the digital input (DIGITAL ) terminal setting correctly. For details, see Selecting the Digital Input Terminals DIGITAL on page 16. Select the digital input mode correctly. For details, see Selecting the Analog or Digital Input Mode on page 17. Rear panel Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference. CAUTIONS: Do not touch the power cord with wet hands. Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord. Putting Batteries in the Remote Control When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 () terminal, using the digital coaxial cable (not supplied). When the component has a digital optical output terminal, connect it to the DIGITAL 2 (CD) terminal, using the digital optical cable (not supplied). DIGITAL 1 () DIGITAL 2 ( CD ) Before using the remote control, put in two the supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the front panel. 1 On the back of the remote control, remove the battery cover. 2 Insert batteries. Make sure to match the polarity: (+) to (+) and ( ) to ( ). Before connecting a digital optical cable, unplug the protective plug. DIGITAL Notes: When shipped from the factory, the DIGITAL terminals have been set for use with the following components: DIGITAL 1 (coaxial): For player DIGITAL 2 (optical): For CD player When you want to operate the CD player or CD recorder using the COMPU LK remote control system, connect the target component also as described in Analog connections (see page 7). When you want to operate the player using the AV COMPU LK remote control system, connect the player also as described in Analog connections (see page 9). 3 Replace the cover. If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type drycell batteries. CAUTION: Follow these precautions to avoid leaking or cracking cells: Place batteries in the remote control so they match the polarity: (+) to (+) and ( ) to ( ). Use the correct type of batteries. Batteries that look similar may differ in voltage. Always replace both batteries at the same time. Do not expose batteries to heat or flame. 10

13 PHONES DIGITAL DIGITAL PRO LOGIC DSP /DSP OFF SPEAKERS ON/OFF DIGITAL AUTO SPK 1 2 ONE TOUCH OPERATION BASS BOOST PUT ATT EON RDS SLEEP ANALOG L C R PRO LOGIC DSP H.PHONE AUTO MUTG TUNED STEREO TA NEWS FO VOLUME LEAR PCM S.WFR LFE DIGITAL LS S RS CH SUBWOOFER FM/AM TUNG FM/AM RESET FM MODE MEMORY ON/OFF DIMMER PUT DIGITAL PUT ANALOG PUT ATT Getting Started/Basic Operations Basic Operations Front panel Remote control STANDBY/ON and STANDBY lamp 1 4 A/V CONTROL RECEIVER STANDBY/ON AUDIO RX 6030V AUDIO/VIDEO CONTROL RECEIVER 7/P TA/NEWS/FO 10 DISPLAY MODE Source selection buttons Source selection buttons Turning On the Power Press STANDBY/ON (or STANDBY/ON AUDIO on the remote control). The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display. To turn off the power (into standby mode) Press STANDBY/ON (or STANDBY/ON AUDIO on the remote control) again. The STANDBY lamp lights up. A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord. TAPE/CDR*: Select the cassette deck (or the CD recorder). FM (front panel): Select an FM broadcast. AM (front panel): Select an AM broadcast. FM/AM* (remote control): Select an FM or AM broadcast. Each time you press the button, the band alternates between FM and AM. RX-5030VBK/RX-5032VSL On the front panel From the remote control TV SOUND TAPE/CDR CD CD TAPE/CDR SOURCE NAME FM/AM Selecting the Source to Play FM/AM TV SOUND ANALOG /DIGITAL Press one of the source selection buttons. The selected source name appears on the display. RX-6030VBK/RX-6032VSL On the front panel MULTI TV SOUND CD TAPE/CDR FM AM From the remote control MULTI: : : TV SOUND: CD*: SOURCE NAME TAPE/CDR CD MULTI FM/AM TV SOUND ANALOG /DIGITAL Select the player for viewing a digital video disc using the analog discrete output mode (5.1 channel reproduction). To use the MULTI playback, see page 28. Select the player. Select the. Select the TV sound (or the CATV converter). Select the CD player. : : TV SOUND: CD*: TAPE/CDR*: FM/AM*: Select the player. Select the. Select the TV sound (or the CATV converter). Select the CD player. Select the cassette deck (or the CD recorder). Select an FM or AM broadcast. Each time you press the button, the band alternates between FM and AM. Notes: When connecting a CD recorder to the TAPE/CDR jacks, change the source name to CDR so that CDR appears on the display when selected as the source. See Changing the Source Name on page 12. When you have connected some digital source components using the digital terminals (see page 10), you need to select the digital input terminals (see page 16). When you press one of the source selection buttons on the remote control marked with an asterisk (*), the receiver automatically turns on. 11

14 STANDBY STANDBY/ON DIGITAL DIGITAL PRO LOGIC DSP /DSP OFF MULTI ON/OFF DIGITAL AUTO SPK 1 2 ONE TOUCH OPERATION BASS BOOST PUT ATT EON RDS SLEEP ANALOG L C R PRO LOGIC DSP H.PHONE AUTO MUTG TUNED STEREO TA NEWS FO VOLUME LEAR PCM S.WFR LFE DIGITAL LS S RS CH TV SOUND FM/AM TUNG FM/AM RESET FM MODE MEMORY PUT DIGITAL PUT ANALOG PUT ATT Basic Operations Front panel DIMMER MASTER VOLUME control Remote control TA/NEWS/FO RX 6030V AUDIO/VIDEO CONTROL RECEIVER DISPLAY MODE Audio source selection buttons DIMMER MUTG PHONES jack SPEAKERS ON/OFF SOURCE NAME (TAPE/CDR) Audio source selection buttons VOLUME +/ Changing the Source Name When you have connected a CD recorder to the TAPE/CDR jacks on the rear panel, change the source name to CDR so that CDR appears on the display when selected as the source. RX-6030VBK/RX-6032VSL RX-5030VBK/RX-5032VSL CD TAPE/CDR FM AM CD SOURCE NAME TAPE/CDR SOURCE NAME Remote NOT FM/AM Selecting Different Sources for Picture and Sound You can watch the picture from a video component while listening to sound from another component. Press one of the audio source selection buttons while watching the picture from a video component such as the or player. Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source. 1 Press TAPE/CDR (SOURCE NAME) on the front panel to select TAPE as the source. 2 Press again and hold SOURCE NAME (TAPE/CDR) on the front panel until ASSIGN CDR appears on the display. RX-6030VBK/RX-6032VSL CD TAPE/CDR FM AM SOURCE NAME On the front panel RX-5030VBK/RX-5032VSL TAPE/CDR CD MULTI FM/AM TV SOUND ANALOG /DIGITAL From the remote control To change the source name from CDR to TAPE, repeat the same procedure above. CD TAPE/CDR FM/AM TAPE/CDR CD FM/AM TV SOUND ANALOG /DIGITAL Without changing the source name, you can still use the connected components; however, you may experience one of the following inconveniences: A different source name will appear on the display when you select the target component. You cannot use the digital input (see page 16) for the CD recorder. You cannot use the COMPU LK remote control system (see page 29) to operate the target component. SOURCE NAME On the front panel From the remote control 12

15 Basic Operations Adjusting the Volume On the front panel To increase the volume, turn MASTER VOLUME control clockwise. To decrease the volume, turn MASTER VOLUME control counterclockwise. From the remote control To increase the volume, press VOLUME +. To decrease the volume, press VOLUME. The volume level can be adjusted within a range of 0 (minimum) to 50 (maximum). CAUTION: Always set the volume to the minimum before starting any source. If the volume is set at a high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers. Listening with Headphones Only Remote NOT You must turn off the speakers when you listen with headphones. 1 Press SPEAKERS ON/OFF on the front panel. HEADPHONE appears on the display for a while. The SPK indicator goes off and the H.PHONE indicator lights up. After using the headphones 1 Press SPEAKERS ON/OFF on the front panel to activate the speakers. The H.PHONE indicator goes off and the SPK indicator lights up. 2 Disconnect the headphones. CAUTION: Be sure to turn down the volume Before connecting or putting on headphones, as high volume can damage both the headphones and your hearing. Before turning on speakers again, as high volume may be output from the speakers. Turning Off the Sound Temporarily Muting You can turn off the volume temporarily. Press MUTG on the remote control to mute the sound through all speakers or headphones. MUTG appears on the display and the volume turns off (the VOLUME indicator goes off). To restore the sound, press MUTG again. The VOLUME indicator lights up on the display. Turning MASTER VOLUME control on the front panel or pressing VOLUME +/ on the remote control also restores the sound. This cancels the Surround/DSP modes currently selected and activates the HEADPHONE mode (see below). 2 Connect a pair of headphones to the PHONES jack on the front panel. HEADPHONE mode When using the headphones, the following signals are sent to the headphones regardless of your speaker setting: For 2 channel sources, the front left and right channel signals are sent directly to the headphones. For multi-channel sources, the front left/right, center, and surround left/right channel signals are down-mixed and then sent to the headphones. You can enjoy multi-channel sound sources using the headphones. While in the HEADPHONE mode, you cannot use any Surround /DSP modes (see page 24). Changing the Display Brightness DIMMER You can dim the display. Press DIMMER. Each time you press the button, the display dims and brightens alternately. 13

16 Basic Operations Turning Off the Power with the Sleep Timer You can fall asleep while listening to music Sleep Timer. Basic adjustment auto memory This receiver memorizes sound settings for each source when : you turn off the power, you change the source, and you assign the source name /P 10 A/V CONTROL RECEIVER TA/NEWS/FO DISPLAY MODE SLEEP When you change the source, the memorized settings for the newly selected source are automatically recalled. The following can be stored for each source: Input attenuator mode (see page 18) Tone adjustment (see page 20) Speaker output level (see page 20) Surround/DSP mode selection (see pages 26 and 27) RX-6030VBK and RX-6032VSL only: BASS BOOST (see page 18) Notes: Press SLEEP on the remote control repeatedly. The SLEEP indicator lights up on the display. Each time you press the button, the shut-off time changes in 10 minute intervals as follows: (Canceled) When the shut-off time comes, the receiver turns off automatically. To check or change the shut-off time, press SLEEP once. The remaining time (in minutes) until the shut-off time appears. To change the shut-off time, press SLEEP repeatedly You cannot assign and store different settings for digital input mode and analog input mode. If the source is FM or AM, you can assign a different setting for each band. For recording You can record any sources playing through the receiver to a cassette deck (or a CD recorder) connected to the TAPE/CDR jacks and the connected to the jacks at the same time. While recording, you can listen to the selected sound source at whatever sound level you like without affecting the sound levels of the recording. The output volume level, tone adjustment (see page 20), and Surround/DSP modes (see pages 26 and 27) do not affect the recording. To cancel the Sleep Timer, press SLEEP repeatedly until SLEEP 0 M appears on the display. (The SLEEP indicator goes off.) Turning off the power also cancels the Sleep Timer. 14

17 RY DIMMER PUT DIGITAL PUT ANALOG PUT ATT SETTG SET MULTI JOG ADJUST EXIT Basic Operations/Basic Settings Basic Settings Basic Settings Using MULTI JOG Dial After connecting and placing speakers, you need to make basic settings for the following items according to your listening conditions. Speaker information (see the next column and page 16) Digital input terminal sources (see page 16) RX-6030VBK and RX-6032VSL only: Video input terminal type (see page 16) 7 Operating buttons 4 Turn MULTI JOG dial to adjust the selected item. Select SUBWOOFER YES if a subwoofer is connected. Ex.: When SUBWOOFER YES is selected. 5 Press EXIT. To adjust other items, repeat steps 2 to 5. To finish the setting, go to step 6. SETTG MULTI JOG ADJUST 6 Press EXIT again. The receiver exits from the basic setting mode. Buttons SETTG MULTI JOG SET EXIT SET EXIT To do Enter the receiver into the basic setting mode. Select an item to adjust after pressing SETTG. Adjust the selected item after pressing SET. Determine the item to adjust. Exit from the basic setting mode or return to the previous step. Setting the Speaker Information NO for the subwoofer, LARGE for the front speakers, and SMALL for the center and surround speakers are initial settings. To get best possible sound, change the subwoofer and speaker settings to fit your listening conditions. 7 Subwoofer information SUBWOOFER Register whether you have connected a subwoofer or not. YES NO Select this when you have connected a subwoofer. You can adjust the subwoofer output level (see page 21). Select this when you have not connected or have disconnected a subwoofer. 7 Operating procedure Ex. Setting the subwoofer information Before you start, remember... There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again. 1 Press SETTG. The last selected item appears on the display. 2 Turn MULTI JOG dial to select an item you want to adjust. SUBWOOFER O FRNT SPEAKERS O CNTR SPEAKER O SURR SPEAKERS O DISTANCE UNIT O FRNT DISTANCE O CNTR DISTANCE O SURR DISTANCE O CROSSOVER O LFE ATTENUATE O D_COMPRESSION O DIGITAL O VIDEO * O VIDEO * O (back to the beginnning) * RX-6030VBK and RX-6032VSL only. 3 Press SET. The current setting of the selected item appears on the display. 7 Speaker size FRNT (Front) SPEAKERS, CNTR (Center) SPEAKER, SURR (Surround) SPEAKERS Register the sizes of all the connected speakers. When you change your speakers, register the information about the speakers again. LARGE SMALL NONE Select this when the size of the cone speaker unit built in your speaker is greater than 12 cm (4 3 /4 inches). Select this when the size of the cone speaker unit built in your speaker is smaller than 12 cm (4 3 /4 inches). Select this when you have not connected a speaker. (Not selectable for the front speakers) Notes: If you have selected NO for the subwoofer setting, you can only select LARGE for the front speaker setting. If you have selected SMALL for the front speaker setting, you cannot select LARGE for the center and surround speaker settings. Ex.: When SUBWOOFER is selected. 15

18 Basic Settings 7 Speaker distance DISTANCE UNIT, FRNT DISTANCE, CNTR DISTANCE, SURR DISTANCE Select the unit to measure the distance between your listening position and speakers METER or FEET. After selecting the measuring unit, select the appropriate speaker distance for each speaker within the range of 0.3m ( 1FT ) to 9.0m ( 30FT ) by 0.3 m (1 foot) step. Example: In this case, set FRNT DISTANCE to 3.0m ( 10FT ), CNTR DISTANCE to 2.7m ( 9FT ), and SURR DISTANCE to 2.4m ( 8FT ). L C R 7 Dynamic range compression D_COMPRESSION You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when using surround sound at night. This function takes effect only when playing back a source using Dolby Digital. MID MAX OFF Select this when you want to reduce the dynamic range a little (initial setting). Select this when you want to apply the compression effect fully. (Useful at night.) Select this when you want to enjoy surround sound with its full dynamic range. (No effect applied.) LS 3.0 m (10 feet) 2.7 m (9 feet) 2.4 m (8 feet) 2.1 m (7 feet) RS Selecting the Digital Input Terminals DIGITAL When you use the digital input terminals, register which components are connected to which terminals (DIGITAL 1/2) so that the correct source name will appear when you select the digital source. Select the appropriate option from the following: METER for the unit and 3.0m ( 10FT ) for all speakers are the initial settings. If you have selected NONE for the center and surround speakers setting, you cannot set the speaker distance for the center and surround speakers. 7 Crossover frequency CROSSOVER Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned to the small speaker to other large speakers. To use this function properly, set the crossover frequency according to the table below: Crossover frequency 80HZ 100HZ 120HZ 150HZ 200HZ Size of cone speaker unit built in the small speaker about 12 cm (4 3 /4 inches) about 10 cm (3 15 /16 inches) (initial setting) about 8 cm (3 3 /16 inches) about 6 cm (2 3 /16 inches) less than 5 cm (2 inches) If you have selected LARGE for all speakers, this function will not take effect ( CROSS OFF appears). 1 2 CD O 1 2 TV O 1 2 CDR O 1 CD 2 O 1 CD 2 TV O 1 CD 2 CDR O 1 TV 2 O 1 TV 2 CD O 1 TV 2 CDR O 1 CDR 2 O 1 CDR 2 CD O 1 CDR 2 TV O (back to the beginning) When shipped from the factory, the DIGITAL terminals have been set for use with the following components: DIGITAL 1 (coaxial): For player DIGITAL 2 (optical): For CD player Selecting the Video Input Terminal VIDEO, VIDEO This receiver is equipped with component video input terminals which give you higher picture quality for the player and. When you use the component video input terminals for the player and/or, change the video input terminal setting to use the AV COMPU LK remote control system correctly (see page 30). COMPONENT S/C RX-6030V RX-6032V ONLY Select this when you connect the player and/or to the component video input terminals. Select this when you connect the player and/or to the S-video or composite video input terminal (initial setting). 7 Low Frequency Effect attenuator LFE ATTENUATE If the bass sound is distorted while playing back software encoded with Dolby Digital or DTS Digital Surround, select 10dB to activate the Low Frequency Effect attenuator. This function takes effect only when the LFE signals come in. 0dB 10dB Normally select this (initial setting). Select this when the bass sound is distorted. 16

19 PHONES DIGITAL DIGITAL PRO LOGIC DSP /DSP OFF SPEAKERS ON/OFF DIGITAL AUTO SPK 1 2 ONE TOUCH OPERATION BASS BOOST PUT ATT EON RDS SLEEP ANALOG L C R PRO LOGIC DSP H.PHONE AUTO MUTG TUNED STEREO TA NEWS FO VOLUME LEAR PCM S.WFR LFE DIGITAL LS S RS CH SUBWOOFER FM/AM TUNG FM/AM RESET FM MODE MEMORY ON/OFF Basic Settings Front panel PUT DIGITAL Remote control DISPLAY MODE RX 6030V AUDIO/VIDEO CONTROL RECEIVER Source selection buttons ANALOG/DIGITAL Source selection buttons PUT ANALOG REMOTE CONTROL RM SRX6030J Selecting the Analog or Digital Input Mode When you have connected digital source components using both the analog connection (see pages 7 9) and the digital connection (see page 10) methods, you need to select the input mode correctly. 1 Press one of the source selection buttons, TV SOUND, CD, or TAPE/CDR* for which you want to change the input mode. * Among the sources listed above, you can select the digital input only for the sources for which you have selected the digital input terminals. (See Selecting the Digital Input Terminals DIGITAL on page 16.) 2 Select digital input mode. On the front panel Press PUT DIGITAL. DIGITAL AUTO appears on the display. The DIGITAL AUTO indicator also lights up. To change the input mode back to analog input, press PUT ANALOG. ANALOG appears on the display for a while. The ANALOG indicator lights up. From the remote control Press ANALOG/DIGITAL. Each time you press the button, the input mode alternates between the analog input ( ANALOG ) and the digital input ( DIGITAL AUTO ). DIGITAL AUTO ANALOG Select this for the digital input mode. The receiver automatically detects the incoming signal format. Select this for the analog input mode (initial setting). If the following symptoms occur while playing Dolby Digital or DTS encoded software with DIGITAL AUTO selected, change the digital input mode. Sound does not come out at the beginning of playback. Noise comes out while searching or skipping chapters or tracks. Press PUT DIGITAL on the front panel Remote repeatedly to select DOLBY DIGITAL or DTS NOT. Each time you press the button, the digital input mode changes as follows: To play back software encoded with Dolby Digital, select DOLBY DIGITAL. To play back software encoded with DTS Digital Surround, select DTS. When you turn off the power or select another source, DOLBY DIGITAL and DTS are canceled and the digital input mode is automatically reset to DIGITAL AUTO. The ANALOG indicator and digital signal format indicators on the display indicate what type of signal comes into the receiver. ANALOG LEAR PCM DIGITAL DIGITAL AUTO DTS DOLBY DIGITAL Lights when the analog input is selected. Lights when Linear PCM signals come in. Lights when Dolby Digital signals come in. Flashes when DOLBY DIGITAL is selected for software not encoded with Dolby Digital signals. Lights when DTS signals come in. Flashes when DTS is selected for software not encoded with DTS signals. When DIGITAL AUTO cannot recognize the incoming signals, no digital signal indicators light up on the display. 17

20 PHONES STANDBY STANDBY/ON DIGITAL DIGITAL PRO LOGIC DSP /DSP OFF MULTI SPEAKERS ON/OFF DIGITAL AUTO SPK 1 2 ONE TOUCH OPERATION BASS BOOST PUT ATT EON RDS SLEEP ANALOG L C R PRO LOGIC DSP H.PHONE AUTO MUTG TUNED STEREO TA NEWS FO VOLUME LEAR PCM S.WFR LFE DIGITAL LS S RS CH TV SOUND CD TAPE/CDR FM AM FM/AM TUNG FM/AM RESET SOURCE NAME FM MODE MEMORY DIMMER PUT DIGITAL PUT ANALOG PUT ATT SETTG Sound Adjustments Front panel Remote control PUT ATT ADJUST RX 6030V AUDIO/VIDEO CONTROL RECEIVER RX-6030V RX-6032V ONLY BASSBOOST REMOTE CONTROL RM-SRX6030J SUBWOOFER ON/OFF SET MULTI JOG dial EXIT Attenuating the Input Signal When the input level of the analog source is too high, the sound will be distorted. If this happens, you need to attenuate the input signal level to prevent the distortion. Once this has been adjusted, this receiver memorizes the adjustment for each source. Press and hold PUT ATT on the front panel so that the PUT ATT indicator lights up on the display. Each time you press and hold the button, the Input Attenuator mode turns on ( PUT ATT ON ) or off ( PUT NORMAL ). When selecting MULTI (RX-6030VBK and RX-6032VSL only) as the source, this effect does not work. Turning Off the Subwoofer Remote NOT Remote NOT When the subwoofer is set to YES (see page 15), you can choose to turn off the subwoofer. Press SUBWOOFER ON/OFF on the front panel to turn off the subwoofer. SUBWOOFER OFF appears on the display for a while and the S.WFR indicator goes off. Notes: This button does not work when the subwoofer is set to NO (see page 15). In this case, NO SUBWOOFER will appear on the display for a while. You cannot turn off the subwoofer when the front speaker size is set to SMALL. When you change the subwoofer from NO to YES, the subwoofer is automatically turned on. Reinforcing the Bass You can boost the bass level. Once you have adjusted the bass boost level, this receiver memorizes the adjustment for each source. Press BASSBOOST on the remote control to select the bass boost function. Each time you press the button, the bass boost function turns on and off. BASSBOOST ON BASSBOOST OFF Select this to activate the bass boost function. The BASS BOOST indicator lights up on the display. Select this to cancel it. The BASS BOOST indicator goes off. This function affects the front speakers sound only. RX-6030V RX-6032V ONLY The subwoofer sound comes out of the front speakers. To turn on the subwoofer, press the button again. 18

21 DIMMER PUT DIGITAL PUT ANALOG PUT ATT SETTG SET MULTI JOG ADJUST EXIT Sound Adjustments Sound Adjustments Using MULTI JOG Dial You can adjust the sound using MULTI JOG dial on the front panel. Tone BASS, TREBLE Subwoofer output level* SUBWFR LEVEL Speakers output level* FRONT L/R LEVEL, CENTER LEVEL, SURR L/R LEVEL Effect level for DAP modes EFFECT Panorama control for Pro Logic II Music PANORAMA CTRL * You can also use the remote control to adjust these items (see pages 20 and 21). 7 Operating buttons 2 Turn MULTI JOG dial to select an item you want to adjust. BASS O TREBLE O SUBWFR LEVEL* O FRONT L LEVEL O FRONT R LEVEL O CENTER LEVEL* O SURR L LEVEL* O SURR R LEVEL* O EFFECT* O PANORAMA CTRL* O (back to the beginnning) * These adjustments will depend on the following settings: Subwoofer information Speaker size setting The current Surround/DSP mode For details, see the next page and Adjustable items and selected Surround/DSP mode on page 27. SETTG MULTI JOG ADJUST 3 Press SET. The current setting of the selected item appears on the display. SET EXIT Buttons ADJUST MULTI JOG SET EXIT To do Enter the receiver into the sound adjusting mode. Select an item to adjust after pressing ADJUST. Adjust the selected item after pressing SET. Determine the item to adjust. Exit from the sound adjusting mode or return to the previous step. EX.: When BASS is selected. 4 Turn MULTI JOG dial to select an appropriate value. Adjust the bass sound level within the range of 10 to +10. EX.: When the bass level is adjusted to Press EXIT. To adjust other items, repeat steps 2 to 5. To finish the adjustment, go to step 6. 7 Operating procedure Ex. When adjusting the bass sound Before you start, remember... There is a time limit in doing the following steps. If the setting is canceled before you finish, start again from step 1. 6 Press EXIT again. The receiver exits from the sound adjusting mode. 1 Press ADJUST. The last selected item appears on the display. TO BE CONTUED TO THE NEXT PAGE 19

22 Sound Adjustments 7 Tone BASS, TREBLE Adjust the bass and treble sounds as you like ( 10 to +10 in 2 step intervals). 0 is the initial setting. 7 Subwoofer output level SUBWFR LEVEL Adjust the subwoofer output level ( 10 to +10 in 1 step interval). 0 is the initial setting. Subwoofer output level cannot be adjusted in the following cases: When SUBWOOFER NO is selected for the subwoofer setting (see page 15). When the HEADPHONE mode is in use (see page 13). 7 Speakers output level Adjust the speakers output level so that you can hear sounds from each speaker at an equal level ( 10 to +10 in 1 step interval). 0 is the initial setting for all speakers. FRONT L LEVEL FRONT R LEVEL CENTER LEVEL* SURR L LEVEL* SURR R LEVEL* Left front speaker output level Right front speaker output level Center speaker output level Left surround speaker output level Right surround speaker output level * You can adjust these items depending on the current speaker settings (see page 15) and Surround/DSP mode (see Adjustable items and selected Surround/DSP mode on page 27). Notes: You cannot adjust the center speaker output level when the center speaker size is set to NONE (see page 15). You cannot adjust the surround speaker output levels when the surround speaker size is set to NONE (see page 15). 7 Effect level for DAP modes EFFECT You can adjust the effect level for DAP modes only when one of the DAP modes is activated (EFFECT 1 to EFFECT 5). EFFECT 3 is the initial setting. As the number increases, the effect becomes more stronger. For DAP modes, see page Panorama control for Pro Logic II Music PANORAMA CTRL You can turn on or off the Panorama control for Pro Logic II Music only when PL II MUSIC is activated. Select PANORAMA ON to enjoy wraparound sound effect with side-wall image ( OFF is the initial setting). For Pro Logic II Music, see page 24. Sound Adjustments Using Remote Control You can also use the remote control to adjust the speaker output levels and the subwoofer output level. You can use the test tone to make your favourite adjustments (except for subwoofer level adjustment). TEST FRONT L CENTER SURR L SOUND TEST 1 4 7/P 10 A/V CONTROL RECEIVER FRONT L FRONT R 2 CENTER 5 SURR L 8 0 LEVEL SUBWFR SURR R Adjusting Speaker Output Levels Using Test Tone The center and surround speakers are temporarily activated and you can adjust them when you are listening to stereo sound or one of the DAP modes is activated. Notes: You cannot adjust the center speaker output level when the center speaker size is set to NONE (see page 15). You cannot adjust the surround speaker output levels when the surround speaker size is set to NONE (see page 15) DISPLAY MODE FRONT R SUBWFR SURR R LEVEL +/ 20