BSc Systems 3 Unified Communications Chapter 1
|
|
- Moris Nicholson
- 6 years ago
- Views:
Transcription
1 Chapter 1 - Cisco Voice Gateways Voice gateways are an integral part of the Voice over Internet Protocol (VoIP) network. In their most simple form, gateways are used to connect dissimilar networks, such as the IP network to the traditional Public Switched Telephone Network (PSTN). In essence, the primary function of a gateway is to convert data travelling through it to a format that the other side understands. The CVOICE exam objectives covered in this chapter are: Describe the function of gateways Describe DSP functionality Describe the different types of voice ports and their usage Describe dial peer types Describe codec s and codec complexity This chapter is divided into the following sections Voice Terminology Voice Gateways DSP Resources Circuit Signalling Analogue Circuits FXO and FXS Ports E&M Ports Digital Circuits Integrated Services Digital Network (ISDN) Voice Dial Peers Voice Encoding Voice Terminology Before delving into detail on gateways, it is imperative to have an understanding of the jargon used in traditional voice and VoIP implementations. This section does not provide significant detail on the phrases listed below, nor does it list all terminology currently used in voice networking. Instead, it provides a basic definition of some of the most common the terms that are used in this chapter, as well as in this guide. Keep in mind, however, that some of these terms will be expanded upon in this chapter and throughout this guide. The following is a list of terms and acronyms that are generally used in voice networking: ANI Bandwidth Consumption
2 CAC Codec Caller ID CLID CNID Delay DNIS Echo Jitter Packetization PSTN Serialization TDM VAD VoIP ANI Automatic Number Identification (ANI) refers to the telephone number of the calling party. Bandwidth Consumption Bandwidth consumption is the characteristic bandwidth required between two points to transport traffic. In other words, it is the amount of bandwidth required to transport data from point A to point B, for example. In voice networking, bandwidth is moderated by several methods of Call Admission Control (CAC). CAC Call Admission Control (CAC) is the tracking of bandwidth resources and traffic requests for the purposes of preventing oversubscription within the constraints of the current bandwidth. CAC prevents endpoints from sending more information, or attempting to send more information, than the available bandwidth can handle. Codec A codec, or coder / decoder, is a means of sampling, then digitally representing voice with a given level of compression. Caller ID
3 Caller ID (CID) describes the delivery of a calling name or number, or both. CLID Calling Line Identifier (CLID) is similar to ANI and refers to the number of the calling party. CNID The Calling Number Identification or Calling Name Identification is the same as the ANI. Delay Delay is the latency -- one way or round-trip -- that is incurred when packets are transmitted from one location to another. Delay includes the amount of processing time for intervening devices between source and destination. There are two types of delay: fixed and variable delay. DNIS The Dialed Number Identification Service is the telephone number of the called party. This refers to the number that the telephone company sends to the destination. The DNIS may or may not be the actual number the calling party dials to reach the destination. For example, the caller may dial one number, but it may be translated or redirected by the telephone provider and those digits would be sent to the destination. Echo Echo is the reflection of sound caused by a mismatch in impedance. Impedance measures how easily a circuit conducts current when a voltage runs through it. Impedance is a way of telling you how much of the voltage introduced at one end will really make it to the other end. Impedance is measured in ohms. Jitter Jitter is the variation in delay incurred in a given voice or packet stream. The varying arrival time of the packets can cause gaps in the recreation and playback of the original voice signal, which is undesirable and annoying to the listener. Jitter can be addressed by using de-jitter buffers. Packetization Packetization is the time it takes to put digital voice information into packets and remove the information from packets. Packetization delay is the time taken to fill a packet payload with encoded or compressed speech. This delay is a function of the sample block size required by the voice encoder (vocoder) and the number of blocks placed in a single frame. Packetization delay can also be called Accumulation delay, as the voice samples accumulate in a buffer before they are released. As a general rule, strive for a packetization delay of no more than 30ms. PSTN The Public Switched Telephone Network (PSTN) is the familiar telephone network, comprising of a Central Office (CO) and tie lines, which provide local and long distance calling. The PSTN is largely governed by technical standards created by the ITU-T, and uses E.164 addresses, which are telephone numbers. E.164 addresses will be described in detail later in this chapter. On the PST, the local telephone provider services neighborhoods via a local CO. The CO is the place where the telephone company terminates lines and switches calls between different locations. On the network side, the CO is typically connected to a regional CO that connects to the digital WAN, allowing the local telephone provider to provide local, national long distance, and even international long distance service to subscribers.
4 On the customer facing side, the telephone company may employ the use of remote switching facilities between the subscriber premise and the CO. While most signals received from the subscriber premise are analog signals, some remote switching facilities have the ability to convert those received analog signals into digital signals before forwarding them on to the local CO. The portion of the PSTN that connects the home to the local CO is referred to as the local loop or last mile. Going into detail on the PSTN is beyond the scope of the current CVOICE. Serialization Serialization is the insertion of bits onto a link. Serialization delay is the amount of time it takes for a networking device, such as a router, to encode a packet onto the wire for transmission. Serialization delay is incurred when encapsulating or segmenting a data stream into packets for egress from a given interface. The interface must service the packets one at a time, which in turn results in the delay. TDM Multiplexing is a form of transmission that allows multiple signals to travel simultaneously over a single medium. Time Division Multiplexing (TDM) is a means of providing access to transmission media though the use of a time slot. Several signals may be interleaved on the transmission media through the use of multiple time slots. The greater the number of time slots, the shorter the duration of each. VAD Voice Activity Detection (VAD) is a voice encoding algorithm that takes note of silence during voice conversations and suppresses the transmission of voice packets that contain no actual data within them. VoIP Voice over Internet Protocol (VoIP) is a means of compressing voice using a standardized codec, then encapsulating the results within IP for transport over data networks.
5 Voice Gateways Voice gateways are devices that communicate with other voice gateways, gatekeepers, their respective endpoints, and call control agents, such as Cisco Unified Communications Manager or a PBX via voice signaling and media protocols which include MGCP, H.323, SIP, SCCP and RTP. Voice signaling and media protocols will all be described in detail later in this guide. Function of Voice Gateways In VoIP networks, the primary purpose of voice gateways is to provide an interface between the VoIP network and the Public Switched Telephone Network (PSTN). This traditional use of voice gateways is illustrated in the following diagram: As illustrated in the diagram above, the voice gateway is connected to both the VoIP network and the PSTN. The gateway interfaces with the IP network and the PSTN and supports IP signaling control protocols used in Voice over IP, and Time Division Multiplexing (TDM) control protocols used on the PSTN. TDM will be described in detail later in this chapter. Voice gateways are also used to connect analog phones, fax machines and modems over IP networks as illustrated in the following diagram: In hybrid environments that include IP PBX solutions, such as Cisco Unified Communications Manager, and legacy TDM PBX solutions, voice gateways can be used to facilitate communication between the endpoints connected to the IP PBX and the TDM PBX, thus merging the two environments as illustrated in the following diagram:
6 When integrated into the network, the voice gateway allows for communication between the different network types and performs the following tasks, amongst many others: Interfaces with the IP network and the PSTN or PBX Performs call setup and teardown for calls between the VoIP and PSTN Relays Dual Tone Multi Frequency (DTMF) tones Supports IP and TDM control protocols Supports analog fax machines and modems over the IP network Supports call survivability when no Cisco Unified Communications Manager is available Supports Cisco Unified Communications Manager redundancy in CUCM networks Provides supplementary services such as hold, transfer, and conferencing Voice Gateway Components In their most basic form, voice gateways contain an IP interface and a legacy telephone interface. This allows the voice gateway to allow for communication between the IP network and the telephone network by translating between the different transmission formats and protocols used on the two networks. Cisco voice gateways support analog or digital telephony ports, and sometimes both port types, in addition to IP interfaces. Supported analog ports include the following: Foreign Exchange Office Ear and Mouth
7 Foreign Exchange Station Foreign Exchange Office (FXO) ports are used to connect to the PSTN or to a PBX. These are the ports on subscriber devices, such as analog telephones, fax machines and modems that connect to the PSTN via an FXS port. An Ear and Mouth (E&M) port is used to interconnect PBX devices using dedicated circuits from the PSTN. A Foreign Exchange Station (FXS) port is used to connect analog devices, such as analog telephones, fax machines, and modems. FXS ports are the ports that subscribers plug a telephone, fax machine or modem into. FXS ports provide telephony services for these devices. FXO, E&M, and FXS ports will be described in detail later in this chapter in the section pertaining to voice ports. Cisco voice gateways also support digital ports and interfaces, which include the following: T1 Primary Rate Interface T1 Channel Associated Signaling E1 Primary Rate Interface E1 R2 ISDN Basic Rate Interface Integrated Services Digital Network (ISDN) T1 Primary Rate Interface (PRI) provides 23 voicebearer channels, while ISDN E1 PRI provides 30 voice-bearer channels. ISDN T1 PRI standard is used in the United States, while ISDN E1 PRI is used in Europe. T1 Channel Associated Signaling (CAS), also referred to as robbed-bit signaling, is performed on voice channels by robbing the Least Significant Bit (LSB) of information in the channel. CAS will be described in detail later in this chapter. E1 R2 is a Channel Associated Signaling (CAS) system that is used in Europe. And finally, ISDN Basic Rate Interface (BRI) provides two voice-bearer channels for data and voice traffic, in addition to a single data channel for signaling traffic. As is the case with analog ports and circuits, digital ports and circuits will be described in detail later in this chapter on voice ports. The following output shows a Cisco 3845 ISR voice gateway with two GigabitEthernet interfaces, two E1-R2 digital ports, and eight FXO analog ports: R1#show version Cisco IOS Software, 3800 Software (C3845-ADVENTERPRISEK9_IVS-M), Version 12.4(18b), RELEASE SOFTWARE (fc2) Technical Support: Copyright (c) by Cisco Systems, Inc. Compiled Mon 19-May-08 21:58 by prod_rel_team ROM: System Bootstrap, Version 12.4(13r)T10, RELEASE SOFTWARE (fc1)
8 R uptime is 2 weeks, 6 days, 3 hours, 9 minutes System returned to ROM by reload at 20:31:52 UTC Tue Oct System image file is "flash:c3845-adventerprisek9_ivs-mz b.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: If you require further assistance please contact us by sending to export@cisco.com. Cisco 3845 (revision 1.0) with K/46080K bytes of memory. Processor board ID FTX1306A09R 2 Gigabit Ethernet interfaces 2 Channelized E1/PRI ports 1 Virtual Private Network (VPN) Module 8 Voice FXO interfaces DRAM configuration is 64 bits wide with parity enabled. 479K bytes of NVRAM.
9 255488K bytes of ATA System CompactFlash (Read/Write) Configuration register is 0x2102 The voice ports on the voice gateway can be viewed by issuing the show voice port summary command, as illustrated in the following output on the same router illustrated above: R1#show voice port summary PORT CH SIG-TYPE ADMIN OPER IN STATUS OUT STATUS EC 0/0/0 -- fxo-ls up dorm idle on-hook y 0/0/1 -- fxo-ls up dorm idle on-hook y 0/0/2 -- fxo-ls up dorm idle on-hook y 0/0/3 -- fxo-ls up dorm idle on-hook y 0/1/0 -- fxo-ls up dorm idle on-hook y 0/1/1 -- fxo-ls up dorm idle on-hook y 0/1/2 -- fxo-ls up dorm idle on-hook y 0/1/3 -- fxo-ls up dorm idle on-hook y 1/0:1 01 r2-digital up dorm idle idle y 1/0:1 02 r2-digital up dorm idle idle y 1/0:1 03 r2-digital up dorm idle idle y 1/0:1 04 r2-digital up dorm idle idle y 1/0:1 05 r2-digital up dorm idle idle y 1/0:1 06 r2-digital up dorm idle idle y 1/0:1 07 r2-digital up dorm idle idle y 1/0:1 08 r2-digital up dorm idle idle y 1/0:1 09 r2-digital up up answered idle y 1/0:1 10 r2-digital up dorm idle idle y 1/0:1 11 r2-digital up dorm idle idle y 1/0:1 12 r2-digital up dorm idle idle y 1/0:1 13 r2-digital up dorm idle idle y 1/0:1 14 r2-digital up dorm idle idle y 1/0:1 15 r2-digital up dorm idle idle y 1/0:1 17 r2-digital up dorm idle idle y 1/0:1 18 r2-digital up dorm idle idle y 1/0:1 19 r2-digital up up answered idle y 1/0:1 20 r2-digital up dorm idle idle y 1/0:1 21 r2-digital up dorm idle idle y 1/0:1 22 r2-digital up dorm idle idle y 1/0:1 23 r2-digital up dorm idle idle y 1/0:1 24 r2-digital up up answered idle y 1/0:1 25 r2-digital up dorm idle idle y 1/0:1 26 r2-digital up dorm idle idle y 1/0:1 27 r2-digital up dorm idle idle y 1/0:1 28 r2-digital up up answered idle y 1/0:1 29 r2-digital up dorm idle idle y 1/0:1 30 r2-digital up dorm idle idle y 2/0:1 01 r2-digital up dorm idle idle y
10 2/0:1 02 r2-digital up dorm idle idle y 2/0:1 03 r2-digital up dorm idle idle y 2/0:1 04 r2-digital up dorm idle idle y 2/0:1 05 r2-digital up dorm idle idle y 2/0:1 06 r2-digital up dorm idle idle y 2/0:1 07 r2-digital up dorm idle idle y 2/0:1 08 r2-digital up dorm idle idle y 2/0:1 09 r2-digital up dorm idle idle y 2/0:1 10 r2-digital up dorm idle idle y 2/0:1 11 r2-digital up dorm idle idle y 2/0:1 12 r2-digital up dorm idle idle y 2/0:1 13 r2-digital up dorm idle idle y 2/0:1 14 r2-digital up dorm idle idle y 2/0:1 15 r2-digital up up answered idle y 2/0:1 17 r2-digital up dorm idle idle y 2/0:1 18 r2-digital up dorm idle idle y 2/0:1 19 r2-digital up dorm idle idle y 2/0:1 20 r2-digital up dorm idle idle y 2/0:1 21 r2-digital up dorm idle idle y 2/0:1 22 r2-digital up dorm idle idle y 2/0:1 23 r2-digital up dorm idle idle y 2/0:1 24 r2-digital up dorm idle idle y 2/0:1 25 r2-digital up dorm idle idle y 2/0:1 26 r2-digital up dorm idle idle y 2/0:1 27 r2-digital up dorm idle idle y 2/0:1 28 r2-digital up dorm idle idle y 2/0:1 29 r2-digital up dorm idle idle y 2/0:1 30 r2-digital up dorm idle idle y Voice Gateway Capabilities When choosing a voice gateway for Cisco VoIP networks, it is important to ensure that the selected gateway supports the following four core requirements: 1. Dual Tone Multi Frequency Relay 2. Supplementary Services 3. Communications Manager Redundancy 4. Call Survivability DMTF, or Dual Tone Multi Frequency, refers to the tones that are played when the dial pad on a phone is pressed. DTMF is often referred to as touch-tones. Because voice traffic is typically compressed, DTMF can become distorted. The DTMF relay feature allows the DTMF to be sent outof-band, which resolves the distortion problem. The term out-of-band refers to communications which occur outside of a previously established communication method or channel. In this case, DTMF is sent in a channel that is not used by the actual voice traffic. Out-of-band signaling will be described in detail later in this chapter. Voice gateways should support supplementary services. Supplementary services are simply additional services that are available for VoIP. These services include hold capabilities, transfer capabilities, and conferencing capabilities, amongst many others. In Cisco VoIP networks, voice gateways should support Communications Manager redundancy. This allows the gateway to fail over to a secondary Communications Manager in the event that the primary Communications Manager fails.
11 NOTE: Cisco Unified Communications Manager is the new name for what was previously known and referred to as Cisco CallManager. These terms are interchangeable. Finally, voice gateways should support call survivability. This ensures that calls will not drop if the Communications Manager, to which either endpoint is registered, fails. Voice communication clients or endpoints include desktop IP phones, speaker phones, overhead paging systems, voice recording, operator console and wireless products. Voice Gateway Types Cisco voice gateway solutions are divided into three distinct categories. These categories are: 1. Cisco IOS Routers 2. Standalone Voice Gateways 3. Switch Modules Almost all Cisco IOS routers can be used as voice gateways. Cisco IOS routers have the capability to support both analog and digital ports. Common examples of Cisco IOS routers that support voice gateway functionality include Cisco Integrated Series routers, i.e. the Cisco 1800, 2800, and 3800 series routers, and the Cisco 2600XM Series Multiservice Router platforms. Standalone voice gateways can be used only as voice gateways. Whereas routers can be used for other purposes, such as routing and firewall capabilities, standalone voice gateways are dedicated voice gateways that support both analog and digital communications. Analog voice gateways connect to the PSTN or a PBX via analog ports. Additionally, analog voice gateways are also used to connect to various analog devices such as fax machines and modems. Examples of analog voice gateways include the Cisco Analog Telephone Adapter (ATA) series devices and the Cisco Voice Gateway (VG) 200 series voice gateways. Digital voice gateways, such as the Cisco AS5000 series digital voice gateways, connect VoIP networks to the PSTN or a PBX system via their digital trunk ports. Cisco also provides modules that support analog and digital ports which can be integrated into the Cisco Catalyst 6500 series switches and 7600 series routers. These modules include the 6600 series modules, which have now been replaced by corresponding Cisco Catalyst 6500 Series Communication Media Module (CMM) modules. The Cisco Communication Media Module for Catalyst 6500 Series and Cisco 7600 Series supports interconnectivity between the PSTN and traditional PBX systems and IP communication networks and Voice over IP networks.
12 DSP Resources Digital Signal Processor (DSP) resources are used in various Cisco voice gateways to convert analog voice signals to digital transmission across an IP network, and to convert back to analog once the packet has arrived at the destination router. DSP resources provide four critical functions in Cisco voice gateway solutions: Voice Termination Transcoding Conferencing Media Termination Point Voice termination is the process of digitizing and packetizing the voice audio stream on a TDM interface. A DSP is required to convert the traditional audio stream from the PSTN to a Voice over IP (VoIP) stream. DSPs have the capability to support multiple calls; however, the quantity of DSP resources that should be used in contingent on the complexity of the codec being used. In addition to voice termination, DSP resources also provide echo cancellation, Voice Activity Detection (VAD), and jitter management. Transcoders perform real-time translation or digitized voice from one codec to another. Because the various types of codecs, which will be described in detail later in this chapter, are not compatible with each other, transcoders are used to translate from one codec region to another. DSP resources used for Transcoding must be registered to the Cisco Unified Communications Manager via the SCCP protocol, which will be described in detail later in this guide. There are two types of conferencing available in Cisco VoIP solutions: software-based and hardware-based. Both hardware and software conference bridges can be active at the same time. Software and hardware conference devices differ in the number of streams and the types of codec they support. For software conference devices, you can adjust the number of streams. Hardware conference devices, however, support a fixed number of streams. Software-based conferencing is performed in software; however, hardware-based conferencing requires the use of DSPs registered to the Cisco Unified Communications Manager using the SCCP protocol. A Media Termination Point, or MTP, allows the Cisco CallManager to extend supplementary services, such as hold and transfer, to calls routed through an H.323 endpoint or an H.323 gateway. MTPs provide these supplementary services if H.323v2 is not supported end to end. As is the case with conferencing, there are software-based MTPs and hardware-based MTPs. Softwarebased MTPs are supported in Cisco voice gateways and do not require the use of DSP resources; however, hardware-based MTPs require the use of DSP resources. Again, these resources must be registered to the Cisco Unified Communications Manager via SCCP. DSP Types Cisco voice gateways support various types of DSP models, and each model has different capabilities. Some gateways and Network Modules (NM) use modular DSPs, which are referred to as Packet Voice DSP Modules (PVDM), while others use fixed DSPs, such as those found in NM-HD- 2V modules. The recommended DSP types to use are the C5510 DSPs. These high-density packet voice DSP modules are available in five versions, which are PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, and PVDM2-64. The following table shows the number of voice channels and codecs that each PVDM2 module supports: PVDM2 Name PVDM2-8 PVDM2 Description 8-channel packet fax and voice DSP Maximum Channels in G.711 Maximum Channels in High-Complexity Codecs Maximum Channels in Medium-Complexity Codecs
13 PVDM2-16 PVDM2-32 PVDM2-48 PVDM2-64 module 16-channel packet fax and voice DSP module 32-channel packet fax and voice DSP module 48-channel packet fax and voice DSP module 64-channel packet fax and voice DSP module The PVDM2 modules support the G.723.1, G.728, G.729, G.729b, ilbc, and Modem Relay highcomplexity codecs and the G.7112, g.729a, G.729ab, G.726, G.722, and Fax Relay mediumcomplexity codecs. PVDM2 can support a higher density (number) of G.711 calls than that of other medium-complexity codecs. Codecs will be described later in this chapter. NOTE: Calculating the number of DSP resources required is a challenging task that is beyond the scope of this course. Keep in mind that although the calculation can be performed manually, Cisco recommends using the online DSP calculator found directly on the Cisco website. The following table lists the different platforms on which the PVDM2 modules are supported: PVDM2 Name PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, and PVDM2-64 PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, and PVDM2-64 PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, and PVDM2-64 PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, and PVDM2-64 PVDM2-8, PVDM2-16, PVDM2-32, PVDM2-48, and PVDM2-64 Platform Support NM-HDV2, NM-HDV2-1T1/E1, and NM-HDV2-2T1/E1 Cisco 2801, 2811, 2821, and 2851 Integrated Services Routers EVM-HD-8FXS/DID, EM-HDA-8FXS, and EM-4BRI- NT/TE Cisco 3825 and 3845 Integrated Services Routers Cisco 2901, 2911, 2921, 2951, 3925, 3945 Integrated Service Routers The show voice dsp command can be used to view the current status or selective statistics of digital signal processor (DSP) voice channels as illustrated in the following output: R1#show voice dsp FLEX VOICE CARD *DSP VOICE CHANNELS* DSP TX/RX TYPE COUN T DSP NU M C H CODEC DSPWARE VERSION CURR STATE BOOT STATE PAK RST AI VOICEPORT TS PACK ABRT C g711ulaw busy idle 0 0 1/0: C g711ulaw busy idle 0 0 1/0: *DSP SIGNALING CHANNELS* 31041/ / 26555
14 DSP TX/RX TYPE COUN T DSP NU M C H CODEC DSPWARE VERSION CURR STATE BOOT STATE PAK RST AI VOICEPORT TS PACK ABRT C {flex} alloc idle 0 0 0/0/ /0 C {flex} alloc idle 0 0 0/0/ /0 C {flex} alloc idle 0 0 0/0/ /0 C {flex} alloc idle 0 0 0/0/ /0 C {flex} alloc idle 0 0 0/1/ /0 C {flex} alloc idle 0 0 0/1/ /0 C {flex} alloc idle 0 0 0/1/ /0 C {flex} alloc idle 0 0 0/1/ /0 C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: / / / / / / / / / / / / / / / / / / / /65 71
15 C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 1/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: / / / / / / / / / / / / / / / / / / / / / / / / / / /60 24 C {flex} alloc idle 0 0 2/0: /59
16 C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: C {flex} alloc idle 0 0 2/0: END OF FLEX VOICE CARD / / / / / / / / / / FLEX VOICE CARD *DSP VOICE CHANNELS* DSP TX/RX TYPE COUN T DSP NU M C H CODEC *DSP SIGNALING CHANNELS* DSP TX/RX TYPE COUN T DSP NU M C H CODEC DSPWARE VERSION DSPWARE VERSION CURR STATE CURR STATE BOOT STATE BOOT STATE PAK RST AI VOICEPORT TS PACK ABRT PAK RST AI VOICEPORT TS PACK ABRT END OF FLEX VOICE CARD FLEX VOICE CARD *DSP VOICE CHANNELS* DSP TX/RX TYPE COUN T DSP NU M C H CODEC *DSP SIGNALING CHANNELS* DSP TX/RX TYPE COUN T DSP NU M C H CODEC DSPWARE VERSION DSPWARE VERSION CURR STATE CURR STATE BOOT STATE BOOT STATE PAK RST AI VOICEPORT TS PACK ABRT PAK RST AI VOICEPORT TS PACK ABRT
17 END OF FLEX VOICE CARD Voice DSPs can be used both for media and signaling channel resources. Media channels support the actual codec used for a live call while signaling channels are used by analog and CAS voiceports to monitor for and signal line events such as off-hook and on-hook. These concepts will be described in detail later in this chapter. In the output above, the *DSP VOICE CHANNELS* section provides information on DSP channels being used for media on the particular slot. The *DSP SIGNALING CHANNELS* provides information on DSP channels being used for signaling on the particular slot. The remainder of the pertinent columns are listed and described in the following table: Field DSP TYPE DSP NUM CH CODEC DSPWARE VERSION CURR STATE BOOT STATE RST AI VOICEPORT TS PAK ABRT TX/RX PAK COUNT Description This field specifies the DSP architecture type. This can read C542, C549, C5421, or C5510. This field specifies the unique identifier for the DSP in the pool of DSPs installed in the particular slot. This field uniquely identifies the channel on each DSP. Each DSP has logical channels capable of supporting media or signaling, up to 16 per C5510 DSP. Which codec is currently supported by the DSP media channel. This field specifies the DSPware version, which should always be consistent with the IOS version being used. This field specifies the current state of the DSP. This field specifies the boot state of the DSP. This field specifies the number of DSP ReSeTs counted. This field specifies the number of DSP Alarm Indicators counted. This field specifies the the voice port identifier associated with the DSP media or signaling channel. This field is used for digital T1/E1 CAS or PRI voice-ports, and BRI voice-ports, and specifies the TimeSlot involved. This field specifies the count of ABoRTed voice packets. This field specifies the count of transmitted and received voice packets. Cisco voice gateways determine how many voice calls each DSP can terminate based on codec complexity. For example, if the codec complexity is set to medium, the number of voice ports that can be terminated per DSP would be higher than if the codec complexity was set to high. Only voice cards that have C5510 DSPs support flex complexity, as illustrated in the output printed above. Flex complexity allows a variable number of calls per DSP based on voice gateway runtime calculations. Flex complexity is the default complexity for all voice cards that have C5510 DSPs. However, it should be noted that while flex complexity allows the DSPs to support the maximum number of voice calls, it also introduces the possibility of oversubscribing the DSP resources. It is important to understand the effect this may have in a production environment because if the DSPs are oversubscribed, calls will be connected, however, no audio path will exist when all available DSP channels are in use. DSP Sharing DSP sharing allows C5510 DSPs to terminate a voice call that is physically located in another hardware slot on modular platforms such as the Cisco 3800 ISR routers. DSP sharing reduces the possibility of oversubscription when using flex complexity and also makes it easier for the administrators to add DSPs to an existing voice gateway.
18 When DSP sharing is enabled, voice cards allow other voice cards to use their DSP resources. When a call comes in via a T1 or E1, the voice gateway must allocate a DSP for the call. If no local DSP is available for the call, the voice gateway searches for a remote DSP. After the gateway allocates a remote DSP, the DSP remains allocated for the duration of the call, even in the event that a local DSP becomes available. To enable DSP farm (sharing) services for a particular voice network module, use the dsp services dspfarm command in voice-port configuration mode. It is important to keep in mind that the DSPs that are installed on the main board of an ISR (e.g. Cisco 2800 and 3800 series) should always be configured under voice-card 0. Once configured, all other voice card that should participate in the DSP resource pool (including voice-card 0) should be configured with the dspfarm voice-card configuration command. The following output illustrates a sample configuration for basic DSP sharing on a Cisco 3800 ISR router with three PVDM2-64 modules: R1#show inventory include PVDM NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs" PID: PVDM2-64, VID: V01, NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs" PID: PVDM2-64, VID: V01, NAME: "PVDMII DSP SIMM with four DSPs", DESCR: "PVDMII DSP SIMM with four DSPs" PID: PVDM2-64, VID: V01, R1# R1# R1#conf t R1(config)#voice-card 0 R1(config-voicecard)#dsp services dspfarm R1(config-voicecard)#dspfarm R1(config-voicecard)#exit R1(config)#voice-card 1 R1(config-voicecard)#dspfarm R1(config-voicecard)#exit R1(config)#voice-card 2 R1(config-voicecard)#dspfarm R1(config-voicecard)#exit
19 R1(config)#exit This configuration can then be validated via the show running-configuration command: R1#show running-config begin voice-card 0 voice-card 0 dspfarm dsp services dspfarm! voice-card 1 dspfarm! voice-card 2 dspfarm Configuring Conferencing, MTP and Transcoding Resources Once DSP sharing has been enabled, the voice gateway can be configured to register these resources with Cisco Unified Communications Manager. While the configuration of configuration of these elements is beyond the scope of the CVOICE, the following gateway configuration illustrates the configuration of two hardware-based profiles: one for transcoding and the other for conferencing; and one software-based MTP profile.! dspfarm profile 1 conference codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 codec g729r8 codec g729br8 maximum sessions 10 associate application SCCP!
20 dspfarm profile 2 transcode codec g711ulaw codec g711alaw codec g729ar8 codec g729abr8 maximum sessions 9 associate application SCCP! In the output above, the conference profile has been defined with numerous codecs and allows up to a maximum of 10 conference sessions. The transcode profile is also defined with numerous codecs and allows up to 9 transcoding sessions. The associate application SCCP command instructs the voice gateway to register the resources with the Cisco Unified Communications Manager via SCCP. The following voice gateway configuration output illustrates a basic SCCP configuration to register the profiles illustrated above: interface GigabitEthernet0/0 description 'Voice Gateway interface for CUCM SCCP Registration" ip address ! sccp local GigabitEthernet0/0 sccp ccm identifier 1 version 7.0+ sccp! sccp ccm group 1 bind interface GigabitEthernet0/0 associate ccm 1 priority 1 associate profile 1 register CVOICE_CNF_001 associate profile 2 register CVOICE_TRN_001 The DSP show dspfarm dsp all command shows the DSP resources reserved for conferencing and transcoding based on the configuration implemented on the voice gateway: R1#show dspfarm dsp all SLOT DSP VERSION STATUS CHNL USE TYPE RSC_ID BRIDGE_ID PKTS_TXED PKTS_RXED UP N/A FREE xcode
21 UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE xcode UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf UP N/A FREE conf Total number of DSPFARM DSP channel(s) 19 The show dspfarm profile command shows the current status of the DSP sharing profile configuration and whether or not they are associated with the Cisco Unified Communications Manager which they have been configured to register to: R1#show dspfarm profile Dspfarm Profile Configuration Profile ID 2, Service TRANSCODING, Resource ID 1 Profile Description : Profile Admin State : UP Profile Operation State : ACTIVE Application : SCCP Status : ASSOCIATED Resource Provider : FLEX_DSPRM Status : UP Number of Resource Configured : 9 Number of Resource Available : 9 Codec Configuration Codec : g711ulaw, Maximum Packetization Period : 30 Codec : g711alaw, Maximum Packetization Period : 30
22 Codec : g729ar8, Maximum Packetization Period : 60 Codec : g729abr8, Maximum Packetization Period : 60 Dspfarm Profile Configuration Profile ID 1, Service CONFERENCING, Resource ID 2 Profile Description : Profile Admin State : UP Profile Operation State : ACTIVE Application : SCCP Status : ASSOCIATED Resource Provider : FLEX_DSPRM Status : UP Number of Resource Configured : 10 Number of Resource Available : 10 Codec Configuration Codec : g711ulaw, Maximum Packetization Period : 30, Transcoder: Not Required Codec : g711alaw, Maximum Packetization Period : 30, Transcoder: Not Required Codec : g729ar8, Maximum Packetization Period : 60, Transcoder: Not Required Codec : g729abr8, Maximum Packetization Period : 60, Transcoder: Not Required Codec : g729r8, Maximum Packetization Period : 60, Transcoder: Not Required Codec : g729br8, Maximum Packetization Period : 60, Transcoder: Not Required Dspfarm Profile Configuration Finally, the show sccp ccm group command can be used to view the registration of the configured profiles to the Cisco Unified Communications Manager as follows: R1#show sccp ccm group CCM Group Identifier: 1 Description: None Binded Interface: GigabitEthernet0/0, IP Address: Associated CCM Id: 1, Priority in this CCM Group: 1 Associated Profile: 1, Registration Name: CVOICE_CNF_001
23 Associated Profile: 2, Registration Name: CVOICE_TRN_001 Registration Retries: 3, Registration Timeout: 10 sec Keepalive Retries: 3, Keepalive Timeout: 30 sec CCM Connect Retries: 3, CCM Connect Interval: 10 sec Switchover Method: GRACEFUL, Switchback Method: GRACEFUL_GUARD Switchback Interval: 10 sec, Switchback Timeout: 7200 sec Signaling DSCP value: cs3, Audio DSCP value: ef When configuring DSP farming, it is important to remember that you can configure either hardware-based or software-based MTP profiles on the router; however, this is not applicable to transcoding or conferencing profiles, which are only hardware-based and can never be performed in software. The options available for MTP profiles are illustrated below: R1(config)#dspfarm profile 3 mtp R1(config-dspfarm-profile)#maximum sessions? hardware Hardware MTP software Software MTP The following configuration illustrates the configuration of a software-based MTP profile, which is then registered to the Cisco Unified Communications Manager: interface GigabitEthernet0/0 description 'Voice Gateway interface for CUCM SCCP Registration" ip address ! sccp ccm group 1 bind interface GigabitEthernet0/0 associate ccm 1 priority 1 associate profile 3 register CVOICE_001! dspfarm profile 3 mtp codec g711ulaw maximum sessions software 200 associate application SCCP
24 This configuration can then be validated via the show dspfarm profile [number] command: R1#show dspfarm profile 3 Dspfarm Profile Configuration Profile ID 3, Service MTP, Resource ID 3 Profile Description : Profile Admin State : UP Profile Operation State : ACTIVE Application : SCCP Status : ASSOCIATED Resource Provider : NONE Status : NONE Number of Resource Configured : 200 Number of Resource Available : 200 Hardware Configured Resources : 0 Hardware Available Resources : 0 Software Resources : 200 Codec Configuration Codec : g711ulaw, Maximum Packetization Period : 30 In Cisco Unified Communications Manager, this association can be validated under Media Resources > Media Termination Point, as illustrated below on a CUCM 7.0 server:
25 NOTE: The screenshot above is illustrated only as an example. Also remember that you are not required to perform any CUCM or DSP configuration in the CVOICE 6.0 certification exam. This information has been provided above to reinforce the concepts described in this section.
Enhanced Transcoding and Conferencing for IOS Voice Gateways in a CallMananger Network using DSP Resources Configuration Example
Enhanced Transcoding and Conferencing for IOS Voice Gateways in a CallMananger Network using DSP Resources Configuration Example Document ID: 91863 Contents Introduction Prerequisites for Conferencing
More informationConfiguring Enhanced Conferencing and Transcoding for Voice Gateway Routers
Configuring Enhanced Conferencing and Transcoding for Voice Gateway Routers This chapter describes the steps for enabling conferencing and transcoding support on Cisco IOS voice gateways in a Cisco Unified
More informationConfiguring Enhanced Conferencing and Transcoding for Voice Gateway Routers
Configuring Enhanced Conferencing and Transcoding for Voice Gateway Routers This chapter describes the steps for enabling conferencing and transcoding support on Cisco IOS voice gateways in a Cisco Unified
More informationConfiguring Conferencing and Transcoding for Voice Gateway Routers
Configuring Conferencing and Transcoding for Voice Gateway Routers This chapter describes the steps for enabling conferencing and transcoding support on Cisco IOS voice gateways in a Cisco Unified Communications
More informationCisco DSP Resources for Transcoding Conferencing and MTP
Cisco DSP Resources for Transcoding Conferencing and MTP This chapter provides information about how Cisco digital signal processor (DSP) resources are used for transcoding and conferencing. The modules,
More informationTable of Contents. Cisco Troubleshooting the DSP on NM HDV for Cisco 2600/3600/3700/VG200 Series Routers
Table of Contents Troubleshooting the DSP on NM HDV for Cisco 2600/3600/3700/VG200 Series Routers...1 Document ID: 19066...1 Introduction...1 Prerequisites...1 Requirements...1 Components Used...1 Conventions...2
More informationAT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide. Issue /3/2008
AT&T IP Flexible Reach And IP Toll Free Cisco Unified Communication Manager H.323 Configuration Guide Issue 2.17 3/3/2008 Page 1 of 49 TABLE OF CONTENTS 1 Introduction... 4 2 Special Notes... 4 3 Overview...
More informationMedia Resources CHAPTER
CHAPTER 6 Last revised on: October 30, 2008 A media resource is a software-based or hardware-based entity that performs media processing functions on the data streams to which it is connected. Media processing
More informationUnderstand the NM-HDV2 IP Communications High-Density Digital Voice or Fax Network Module
Understand the NM-HDV2 IP Communications High-Density Digital Voice or Fax Network Module Contents Introduction Prerequisites Requirements Components Used Conventions Product Numbers Features of the NM-HDV2
More informationIP Communications High Density Digital Voice/Fax Network Module
IP Communications High Density Digital Voice/Fax Network Module Document ID: 65356 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Key Features Hardware
More informationMedia Resources CHAPTER
17 CHAPTER Revised: April 30, 2013; A media resource is a software-based or hardware-based entity that performs media processing functions on the data streams to which it is connected. Media processing
More informationSynopsis of Basic VoIP Concepts
APPENDIX B The Catalyst 4224 Access Gateway Switch (Catalyst 4224) provides Voice over IP (VoIP) gateway applications for a micro branch office. This chapter introduces some basic VoIP concepts. This chapter
More informationAT&T IP Flexible Reach And IP Toll Free Cisco Call Manager Configuration Guide. Issue /5/2007
And IP Toll Free Cisco Call Manager Configuration Guide Issue 2.13 6/5/2007 Page 1 of 38 TABLE OF CONTENTS 1 Introduction... 3 2 Special Notes... 3 3 Overview... 4 3.1 Call Manager Site... 4 3.2 TFTP and
More informationAnalog Voice Network Interface Modules for Cisco 4000 Series ISRs
Data Sheet Analog Voice Network Interface Modules for Cisco 4000 Series ISRs NIMs Support Multiple Voice Applications on the Cisco 4000 Series ISRs Introduction The Cisco 4000 Series Integrated Services
More informationHelp. Overview. Steps to Use the Tool. DSP Calculator - Help - Cisco Systems.
Page 1 sur 9 Help Overview Steps to Use the Tool Reading the Results Page Example Understanding DSP Capacity Engineering Overview The total number of PVDMs (Packet Voice/fax Digital Signal Processor (DSP)
More informationUnderstanding Cisco Unified Communications Manager Voice Gateways
CHAPTER 38 Understanding Cisco Unified Communications Manager Voice Gateways Cisco Unified Communications gateways enable Cisco Unified Communications Manager to communicate with non-ip telecommunications
More informationCisco IOS Voice Commands: C clid. clid [if-avail required] [accept-stop] [password password]
Cisco IOS Voice Commands: C clid clid To preauthenticate calls on the basis of the Calling Line Identification (CLID) number, use the clid command in AAA preauthentication configuration mode. To remove
More informationConfigure Conference Bridges
Conference Bridges Overview, page 1 Conference Bridge Types, page 1 Call Preservation, page 4 Call Preservation Scenarios, page 5 Conference Bridge Configuration Task Flow, page 7 Conference Bridges Overview
More informationIntroduction to VoIP. Cisco Networking Academy Program Cisco Systems, Inc. All rights reserved. Cisco Public. IP Telephony
Introduction to VoIP Cisco Networking Academy Program 1 Requirements of Voice in an IP Internetwork 2 IP Internetwork IP is connectionless. IP provides multiple paths from source to destination. 3 Packet
More informationConfiguring FXS Ports for Basic Calls
Configuring FXS Ports for Basic Calls First Published: October 2, 2008 Last updated: March 19, 2010 This module describes how to configure analog Foreign Exchange Station (FXS) ports on a Cisco Integrated
More informationvoice-enabling.book Page 72 Friday, August 23, :19 AM
voice-enabling.book Page 72 Friday, August 23, 2002 11:19 AM voice-enabling.book Page 73 Friday, August 23, 2002 11:19 AM C H A P T E R 4 Offering Bundled and Data Services Chapter 2, VoIP Network Architectures:
More informationUsing Cisco Unified Communications Manager to Configure Conferencing, Transcoding, and Media Termination Point
Using Cisco Unified Communications Manager to Configure Conferencing, Transcoding, and Media Termination Point This chapter describes the steps for enabling conferencing, transcoding, and media termination
More informationCisco Unified Survivable Remote Site Telephony Version 4.2
Survivable Remote Site Telephony Version 4.2 Communications solutions unify voice, video, data, and mobile applications on fixed and mobile networks, delivering a media-rich collaboration experience across
More informationUnified Border Element (CUBE) with Cisco Unified Communications Manager (CUCM) Configuration Example
Unified Border Element (CUBE) with Cisco Unified Communications Manager (CUCM) Configuration Example Document ID: 99863 Contents Introduction Prerequisites Requirements Components Used Conventions Configure
More informationGateways. What's New in This Chapter CHAPTER
CHAPTER 4 Last revised on: October 30, 2008 provide a number of methods for connecting an IP telephony network to the Public Switched Telephone Network (PSTN), a legacy PBX, or key systems. range from
More informationCisco Unified CME Commands: M
Cisco Unified CME Commands: M mac-address (ephone), page 3 mac-address (voice-gateway), page 5 mailbox-selection (dial-peer), page 7 mailbox-selection (ephone-dn), page 9 max-calls-per-button, page 11
More informationBT SIP Trunk Configuration Guide
CUCM 9.1 BT SIP Trunk Configuration Guide This document covers service specific configuration required for interoperability with the BT SIP Trunk service. Anything which could be considered as normal CUCM
More informationVoIP Basics. 2005, NETSETRA Corporation Ltd. All rights reserved.
VoIP Basics Phone Network Typical SS7 Network Architecture What is VoIP? (or IP Telephony) Voice over IP (VoIP) is the transmission of digitized telephone calls over a packet switched data network (like
More informationCisco High-Density Packet Voice Digital Signal Processor Module for Cisco IP Communications Solution
Cisco High-Density Packet Voice Digital Signal Processor Module for Cisco IP Communications Solution Product Overview The Cisco High-Density Packet Voice Digital Signal Processor (DSP) Module (PVDM2) enables
More informationCisco Analog Telephone Adaptor Overview
CHAPTER 1 This section describes the hardware and software features of the Cisco Analog Telephone Adaptor (Cisco ATA) and includes a brief overview of the Skinny Client Control Protocol (SCCP). The Cisco
More informationCisco Survivable Remote Site Telephony Version 4.2
Cisco Survivable Remote Site Telephony Version 4.2 Cisco Unified Communications Solutions unify voice, video, data, and mobile applications on fixed and mobile networks, delivering a media-rich collaboration
More informationConferencing. Restrictions for Conferencing. Information About Conferencing. Conferencing Overview
Restrictions for, on page 1 Information About, on page 1 Configure, on page 9 Configuration Examples for, on page 36 Where to Go Next, on page 57 Feature Information for, on page 57 Restrictions for When
More informationConfiguring the Eight-Port FXS RJ-21 Module
CHAPTER 7 Configuring the Eight-Port FXS RJ-21 Module The Eight-port RJ-21 FXS Module is a high-density analog phone and fax relay interface. By providing service to analog phones and fax machines, the
More informationCommunications Transformations 2: Steps to Integrate SIP Trunk into the Enterprise
Communications Transformations 2: Steps to Integrate SIP Trunk into the Enterprise The Changing Landscape IP-based unified communications is widely deployed in enterprise networks, both for internal calling
More informationCisco Unified Survivable Remote Site Telephony Version 7.1
Survivable Remote Site Telephony Version 7.1 Communications Solutions unify voice, video, data, and mobile applications on fixed and mobile networks, enabling easy collaboration every time from any workspace.
More informationSeries Aggregation Services Routers.
Overview of the Cisco DSP SPA for the ASR 1000 Series Aggregation Services Routers This chapter provides an overview of the release history, features, and MIB support for the Cisco Voice SPA for the ASR
More informationVG224 Voice Gateway SCCP Registration with CME Configuration Example
VG224 Voice Gateway SCCP Registration with CME Configuration Example Document ID: 115021 Contributed by Hussain Ali, Cisco TAC Engineer. Nov 29, 2012 Contents Introduction Prerequisites Requirements Components
More informationCUCM 10.5 / CUBE 9.5. BT SIP Trunk Configuration Guide. 1 BT SIP Trunk Configuration Guide
1 BT SIP Trunk Configuration Guide CUCM 10.5 / CUBE 9.5 BT SIP Trunk Configuration Guide This document covers service specific configuration required for interoperability with the BT SIP Trunk service.
More informationConfiguring Echo Cancellation
Configuring Echo Cancellation Last Updated: December 14, 2011 Echo cancellation is a key function in packet voice Much of the perceived quality of the connection depends on the performance of the echo
More informationGateways. What's New in This Chapter CHAPTER
CHAPTER 13 Revised: September 30, 2011; provide a number of methods for connecting an IP telephony network to the Public Switched Telephone Network (PSTN), a legacy PBX, or key systems. range from specialized,
More informationAvaya PBX SIP TRUNKING Setup & User Guide
Avaya PBX SIP TRUNKING Setup & User Guide Nextiva.com (800) 285-7995 2 P a g e Contents Description... 3 Avaya IP PBX Configuration... 3 Licensing and Physical Hardware... 4 System Tab Configuration...
More informationCustomer Guide to Passive VoIP Recording. March
Customer Guide to Passive VoIP Recording March 2017 www.incontact.com Introduction Customer Guide to Passive VoIP Recording Version: This guide should be used with NICE Uptivity (formerly Premise incontact
More informationConfiguring the Cisco IOS MGCP Gateway
Configuring the Cisco IOS MGCP Gateway Document ID: 42105 Contents Introduction Prerequisites Requirements Components Used Conventions Tasks to Perform Step by Step Summary Configurations Troubleshooting
More informationMobile MOUSe CONVERGENCE+ ONLINE COURSE OUTLINE
Mobile MOUSe CONVERGENCE+ ONLINE COURSE OUTLINE COURSE TITLE CONVERGENCE+ COURSE DURATION 13 Hour(s) of Self-Paced Interactive Training COURSE OVERVIEW This course will prepare you to design, implement
More informationMobile MOUSe IMPLEMENTING VOIP ONLINE COURSE OUTLINE
Mobile MOUSe IMPLEMENTING VOIP ONLINE COURSE OUTLINE COURSE TITLE IMPLEMENTING VOIP COURSE DURATION 13 Hour(s) of Self-Paced Interactive Training COURSE OVERVIEW The Cisco Implementing VoIP course validates
More informationCisco IOS Voice Commands: N
Cisco IOS Voice Commands: N This chapter contains commands to configure and maintain Cisco IOS voice applications. The commands are presented in alphabetical order. Some commands required for configuring
More informationTandem Switch Application (VoIP Mode)
CHAPTER 4 This chapter provides a general description of an application in which a VISM equipped Cisco MGX 8850 and a Cisco VSC 3000 Virtual Switch Controller (Call Agent) combine to provide the functions
More informationIntegrated Voice and Data WAN on T1 E1 Interfaces
Integrated Voice and Data WAN on T1 E1 Interfaces This chapter describes how to implement the Integrated Voice and Data WAN on T1/E1 Interfaces with the AIM-ATM-VOICE-30 Module feature. This card provides
More informationEmbedded Management Functions. Signal backhaul xgcp (CAS), Q.931 (PRI) * Call setup/ teardown xgcp * Connection Handling *
CHAPTER 5 This chapter describes VISM operation. Figure 5-1 shows the functional blocks of VISM. Items marked with a single asterisk apply to VoIP switching and switched AAL2 PVC modes only. Items marked
More informationConfigure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration
Configure Q.SIG PRI Trunks between Call Manager and Avaya S8700/G650 with Unity Voice Mail Integration Document ID: 63790 Contents Introduction Prerequisites Requirements Components Used Conventions Test
More informationImplementing Cisco Voice Communications & QoS (CVOICE) 8.0 COURSE OVERVIEW: WHO SHOULD ATTEND: PREREQUISITES: Running on UC 9.
Implementing Cisco Voice Communications & QoS (CVOICE) 8.0 COURSE OVERVIEW: Running on UC 9.x Software Implementing Cisco Voice Communications and QoS (CVOICE) v8.0 is a 5-day training program that teaches
More informationVoice Gateways CHAPTER
CHAPTER 4 Router PSTN connectivity is generically referred to as voice gateway functionality, offering a gateway for voice over IP (VoIP) calls to, and from, traditional analog or digital PSTN or private
More informationIMPLEMENTING CISCO VOICE COMMUNICATIONS AND QOS
IMPLEMENTING CISCO VOICE COMMUNICATIONS AND QOS V8.0 (CVOICE) COURSE OVERVIEW: Implementing Cisco Voice Communications and QoS (CVOICE) teaches students about voice gateways, characteristics of VoIP call
More informationLucent/Avaya Definity G3si V9 PBX with CallManager using the Cisco 3640-T1 PRI as an MGCP Gateway
Application te Lucent/Avaya Definity G3si V9 PBX with CallManager using the Cisco 3640-T1 PRI as an MGCP Gateway This application note discusses the integration of the Lucent/Avaya Definity G3si V9 PBX
More informationConfiguring the Cisco IPICS RMS Component
Configuring the Cisco IPICS RMS Component APPENDIXA This appendix describes the configuration steps that you must follow to configure the RMS router for use with the Cisco IPICS server. The Cisco IPICS
More informationCisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with E1 PRI NET5 Signaling
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with E1 PRI NET5 Signaling This document describes the interoperability and configuration of a Cisco 2621 voice gateway with a Lucent/Avaya
More informationTech Note: Configuring Q.SIG PRI trunk between Cisco Call Manager and Avaya S8700/G650 with Cisco Unity Voice Mail integration
Tech Note: Configuring Q.SIG PRI trunk between Cisco Call Manager and Avaya S8700/G650 with Cisco Unity Voice Mail integration The objective of this document is to provide Cisco s customers and business
More informationThis chapter provides information about using Cisco Unified Communications Manager for working with and configuring Cisco gateways.
This chapter provides information about using Cisco Unified Communications Manager for working with and configuring Cisco gateways. About gateway setup, page 1 Gateway reset, page 2 Gateway deletion, page
More informationmap q850-cause through mgcp packagecapability
map q850-cause through mgcp package-capability map q850-cause through mgcp packagecapability 1 map q850-cause map q850-cause through mgcp package-capability map q850-cause To play a customized tone to
More informationConfigure Conference Bridges
Conference Bridges Overview, page 1 s, page 1 Conference Bridge Configuration Task Flow, page 6 Conference Bridges Overview Conference bridge for Cisco Unified Communications Manager is a software or hardware
More informationLossless Compression R1, ATM Cell Switching, and External BITS Clocking Source
Lossless Compression R1, ATM Cell Switching, and External BITS Clocking Source The Lossless Compression R1, ATM Cell Switching, and External BITS Clocking Source features introduce a new compression technique
More informationExam : Title : Gateway Gatekeeper Exam. Version : Demo
Exam : 642-453 Title : Gateway Gatekeeper Exam Version : Demo 1. Bob's Bicycles wants to route inbound faxes directly to the recipient's e-mail. Which gateway fax protocol will support this? A. Fax Pass-Through
More informationMusic on Hold. Prerequisites for Music on Hold. Restrictions for Music on Hold
Prerequisites for, page 1 Restrictions for, page 1 Information About, page 2 Configure, page 7 Feature Information for, page 27 Prerequisites for For Unified CME Release 11.6 and previous releases, phones
More informationIP phones do not support multicast at 224.x.x.x addresses.
Prerequisites for, on page 1 Restrictions for, on page 1 Information About, on page 2 Configure, on page 7 Feature Information for, on page 26 Prerequisites for For Unified CME Release 11.6 and previous
More informationfreq-power-twist, on page 64 frequency (cp-dualtone), on page 66
fax interface-type, on page 3 fax protocol (dial peer), on page 5 fax protocol (voice-service), on page 7 fax protocol t38 (dial peer), on page 10 fax protocol t38 (voice-service), on page 13 fax rate
More informationCisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with T1 PRI Signaling
Cisco 2621 Gateway-PBX Interoperability: Lucent/Avaya Definity G3si with T1 PRI Signaling This document describes the interoperability and configuration of a Cisco 2621 voice gateway with a Lucent/Avaya
More informationLossless Compression R1 ATM Cell Switching and External BITS Clocking Source
Lossless Compression R1 ATM Cell Switching and External BITS Clocking Source The Lossless Compression R1, ATM Cell Switching, and External BITS Clocking Source features introduce a new compression technique
More informationInternet Protocol Version 6 (IPv6)
This chapter provides information about Internet Protocol version 6 (IPv6), which is the latest version of the Internet Protocol (IP). Packets are used to exchange data, voice, and video traffic over dual-stack
More informationCisco Voice Over IP Exam(CVOICE)
Cisco Voice Over IP Exam(CVOICE) Number: 642-432 Passing Score: 800 Time Limit: 120 min File Version: 1.0 http://www.gratisexam.com/ CISCO 642-432 Cisco Voice Over IP Exam(CVOICE) 61 Q&A Version 2.30 Important
More informationDistributed IP-PBX. Tele-convergence of IP-PBX / PSTN / FAX / legacy PABX And Distributed network approach with area isolation
Distributed IP-PBX Tele-convergence of IP-PBX / PSTN / FAX / legacy And Distributed network approach with area isolation AL FARUQ IBNA NAZIM Deputy Manager Corporate Solution Link3 Technologies Ltd. www.link3.net
More informationEP502/EP504 IP PBX 1.1 Overview
1.1 Overview The EP502/EP504 is an embedded Voice over IP (VoIP) Server with Session Initiation Protocol (SIP) to provide IP extension phone connection for global virtual office of small-to-medium business
More informationConfiguring Transcoding in AOS
6AOSCG0040-29A August 2012 Configuration Guide This configuration guide outlines the use and configuration of the transcoding feature in ADTRAN Operating System (AOS) products. The guide includes an overview
More informationTELECOMMUNICATION SYSTEMS
TELECOMMUNICATION SYSTEMS By Syed Bakhtawar Shah Abid Lecturer in Computer Science 1 Public Switched Telephone Network Structure The Local Loop Trunks and Multiplexing Switching 2 Network Structure Minimize
More informationsignal through srv version
signal through srv version signal, page 3 signal did, page 8 signal keepalive, page 9 signal pattern, page 11 signal sequence oos, page 15 signal timing idle suppress-voice, page 18 signal timing oos,
More informationCHAPTER. Introduction. Last revised on: February 13, 2008
CHAPTER 1 Last revised on: February 13, 2008 The Cisco Unified Communications System delivers fully integrated communications by enabling data, voice, and video to be transmitted over a single network
More informationContents XO COMMUNICATIONS CONFIDENTIAL 1
www.xo.com XO SIP Service Customer Configuration Guide for Cisco Unified Communications Manager (CUCM) 8.0.3 XO SIP Packages 1 and 2, implemented without Cisco Unified Border Control Element (CUBE) SIP
More informationINTRODUCTION. BridgeWay. Headquarters
MILITARY PRODUCTS INTRODUCTION Voiceboard Corporation s MediaPro products provide enhanced communications capabilities for military applications. State of the art technology, including redundant networking,
More informationUnified Communications Endpoints
CHAPTER 18 Revised: July 31, 2012; A variety of endpoints can be used in a Cisco Unified Communications deployment. These endpoints range from gateways that support ordinary analog phones in an IP environment
More informationIntroduction. H.323 Basics CHAPTER
CHAPTER 1 Last revised on: October 30, 2009 This chapter provides an overview of the standard and the video infrastructure components used to build an videoconferencing network. It describes the basics
More informationNumerics I N D E X. 911 services basic components of, mobile environment call processing, 234 nonmobile environment call processing, 233
I N D E X Numerics A 911 services basic components of, 232 233 mobile environment call processing, 234 nonmobile environment call processing, 233 address management, 288 address resolution, 289 address
More informationFax over IP Troubleshooting Basics
Fax over IP Troubleshooting Basics Whenever you encounter a Fax over IP (FoIP) problem, the following troubleshooting model should always be employed to quickly hone in on the problem cause. This troubleshooting
More informationAT&T VOIP Nortel BCM 50 (Release j) Configuration Guide For Use with AT&T IP Flexible Reach Service. Issue 2.3 3/02/2007
AT&T VOIP Nortel BCM 50 (Release 1.00.2.04j) Configuration Guide For Use with AT&T IP Flexible Reach Service Issue 2.3 3/02/2007 Issue 2.3 Page 1 of 25 TABLE OF CONTENTS 1 Introduction... 4 1.1 Document
More informationAIM-ATM, AIM-VOICE-30, and AIM-ATM-VOICE-30 on the Cisco 2600 Series and Cisco 3660
AIM-ATM, AIM-VOICE-30, and AIM-ATM-VOICE-30 on the Cisco 2600 Series and Cisco 3660 Feature History Release 12.2(2)XA 12.2(2)XB Modification The High-Performance ATM Advanced Integration Module (AIM-ATM)
More informationImplementing Cisco Unified Communications VoIP and QoS v8.0 (CVOICE v8.0)
Implementing Cisco Unified Communications VoIP and QoS v8.0 (CVOICE v8.0) Number: 642-437 Passing Score: 800 Time Limit: 120 min File Version: 1.0 http://www.gratisexam.com/ ActualTests 642-437 Implementing
More informationABSTRACT. that it avoids the tolls charged by ordinary telephone service
ABSTRACT VoIP (voice over IP - that is, voice delivered using the Internet Protocol) is a term used in IP telephony for a set of facilities for managing the delivery of voice information using the Internet
More informationConfigure Gateways. Gateway Overview. Gateway Overview, page 1 Gateway Setup Prerequisites, page 3 Gateway Configuration Task Flow, page 4
Gateway Overview, page 1 Gateway Setup Prerequisites, page 3 Gateway Configuration Task Flow, page 4 Gateway Overview Cisco offers a wide variety of voice and video gateways. A gateway provides interfaces
More informationInternet Protocol Version 6 (IPv6)
CHAPTER 29 Internet Protocol version 6 (IPv6), which is the latest version of the Internet Protocol (IP) that uses packets to exchange data, voice, and video traffic over digital networks, increases the
More informationConfiguring Modem Transport Support for VoIP
Configuring Modem Transport Support for VoIP This chapter explains how to configure modem transport support for Voice over IP (VoIP) and contains the following sections: Modem Transport Support Overview,
More informationPASS4TEST. IT Certification Guaranteed, The Easy Way! We offer free update service for one year
PASS4TEST IT Certification Guaranteed, The Easy Way! \ http://www.pass4test.com We offer free update service for one year Exam : 642-845 Title : Optimizing Converged Cisco Networks Vendors : Cisco Version
More informationFXS (Foreign exchange Station) These POTS ports connect to telephones, fax machines, etc.
Rev. 20170312.195018 6. CME Dial-Plans c cnac o okbook.com F X S P O R T S FXS (Foreign exchange Station) These POTS ports connect to telephones, fax machines, etc. R# show voice port summary Voice-only
More informationCertifyMe. CertifyMe
CertifyMe Number: 642-241 Passing Score: 800 Time Limit: 120 min File Version: 9.6 http://www.gratisexam.com/ CertifyMe 642-241 Exam A QUESTION 1 In a Cisco Unified Contact Center Enterprise design, the
More informationIPNext 187 Hybrid IP-PBX System High-performance Hybrid IP-PBX Solution
IPNext 187 Hybrid IP-PBX System High-performance Hybrid IP-PBX Solution IP-PBX Features www.addpac.com AddPac Technology 2011, Sales and Marketing Contents IP-PBX Features Smart Multimedia Manager VoIP
More informationAT&T VOIP Nortel BCM 200/400 (Release 3.7 build 2.4f) Configuration Guide For Use with AT&T IP Flexible Reach Service. Issue 2.
AT&T VOIP Nortel BCM 200/400 (Release 3.7 build 2.4f) Configuration Guide For Use with AT&T IP Flexible Reach Service Issue 2.3 3/02/2007 Issue 2.3 Page 1 of 27 TABLE OF CONTENTS 1 Introduction... 4 1.1
More informationCisco Exam Implementing Cisco IP Telephony & Video, Part 1 v1.0 Version: 10.0 [ Total Questions: 189 ]
s@lm@n Cisco Exam 300-070 Implementing Cisco IP Telephony & Video, Part 1 v1.0 Version: 10.0 [ Total Questions: 189 ] Cisco 300-070 : Practice Test Question No : 1 Which two codecs are the best codecs
More informationDTMF Relay and Interworking on CUBE Contents
DTMF Relay and Interworking on CUBE Contents Introduction Prerequisites Requirements Components Used Conventions Supported DTMF-Relay Methods for CUBE Support for In-band audio DTMF through G711 Supported
More informationTranscoding. Note. Cisco Unified Border Element Configuration Guide 1
is a process of converting one voice codec to another. For example, transcoding ilbc-g.711 or ilbc-g.729. LTI based Internal API is used to access Digital Signaling Processor (DSP) resources for transcoding.
More informationIP Telephony Endpoints
CHAPTER 21 Last revised on: February 13, 2008 This chapter summarizes various types of IP Telephony endpoints along with their features and QoS recommendations. The IP Telephony endpoints can be categorized
More informationPublic Switched TelephoneNetwork (PSTN) By Iqtidar Ali
Public Switched TelephoneNetwork (PSTN) By Iqtidar Ali Public Switched Telephone Network (PSTN) The term PSTN describes the various equipment and interconnecting facilities that provide phone service to
More informationATM Software Segmentation and Reassembly
Feature History Release Modification 12.2(2)XB Cisco 2600 Series T1/E1 ATM and Cisco 3660 T1 Inverse Multiplexing over ATM (IMA) ATM Adaption Layer 2 (AAL2) Support was introduced. 12.2(8)T This feature
More informationMultilevel Precedence and Preemption
This document describes the (MLPP) service introduced in Cisco Unified Communications Manager Express 7.1 (Cisco Unified CME). Prerequisites for MLPP, page 1 Information About MLPP, page 1 Configure MLPP,
More information