Designer Series Product Guide

Transcription

1 Designer Series Product Guide Table of Contents Table of Contents... Page 1 Overview and General Concept... Page 2 Application... Page 2 Installation Requirements... Page 3 Wiring... Page 4 Technical Specifications... Page 5 Ordering Options... Page 6 Configurations... Page 8 Materials... Page 8 Document Revision History... Page 9 Rev Date 1/9/2017 1

2 Overview and General Concepts Figure 1. Designer Series Switches The INNCOM Designer Series Programmable Switch System provides guestroom designers with greater versatility in meeting guestroom customization requirements. The Designer Series is composed of switch plates and push-button switch configurations that can be mixed and matched to provide the look and functionality desired by the designer. The use of an electronic interface card (MCM4) allows a concentration of guest controls such as room entry lighting, multiroom lighting scenes, master lighting on/off, and maid and privacy requests from a single switch plate. The MCM4 provides a gateway to the room low-voltage communication bus. Through this bus, referred to as the INNCOM S5bus, the functionality performed by any specific switch is reconfigurable meaning that new lighting scenes can be established as requirements change. The Designer Series cover plates are available in a range of colors and materials, from simple white plastic to rich granite and frosted glass. The assembly is designed in such a way that no screws are used to secure the switch plate to the wall. This gives the switch plate a sleek, elegant appearance. Application The Designer Series Programmable Switch System can be used as a replacement for one or more conventional control switches. The product consists of the switch plate, mounting plate, logic card (MCM4), and a variable number of illuminated switches (referred to as DS12 switches). The MCM4 can be set up to provide controls for a specific application. For example, the MCM4 can be configured to set the Do Not Disturb and Make Up Room signals, control lights and drapes, and send a request for butler service. The Designer Series Programmable Switch System can be ordered in various formats. The switch plate and the trim ring around the DS12 switch come in several materials and colors. The LED inside each DS12 switch can be ordered in red or blue; however, with extended lead time, other color choices are available. Another option is labeling. For switches offering multiple functions, the DS12s must be labeled so that guests can easily locate the desired function. The labeling can be engraved or silk-screened on the plate. Similarly, the function can be indicated by an icon or text in the cap of the DS12 switch itself, as shown in Figure 2. Rev 2.0 1/9/2017 2

3 Figure 2. Britsh Gang Designer Series Switch with Icons Figure 3. Unitary DS12 Switch Installation Requirements The DS12 itself (Figure 3) is a unitary switch; i.e., a free-standing assembly. It contains a threaded barrel that fits into a 5/8 (16 mm) drilled opening in the plate. To assemble a plate for a particular application, the installer presses the plate into the framing plate and then inserts each DS12 through the aligned openings, securing it by means of a washer and threaded nut. If the cap contains an icon, before the nut is tightened the installer must ensure that the icon is positioned correctly. The nut can be tightened sufficiently by hand; no tool is needed. Once the DS12s have been inserted into the plate and matching framing plate, the assembly can be mounted in a single-gang electrical box, a single-gang mud ring, or a single-gang low-voltage caddy by means of the mounting plates (Figure 3). This is done by firmly pressing the framing plate tabs into the tab receptor openings of the DS12 wall mounting plate. Rev 2.0 1/9/2017 3

4 Figure 4. Assembly The plastic wall caddy is the most cost-effective installation solution for mounting the DS12 assembly in drywall. The caddy also offers ease of installation and provides a low-profile mounting depth. Note: In many cases the assembly of the switches into the plate and framing plate will take place in the factory. The above instructions are provided to enhance understanding of the product. Wiring The Designer Series Switch is a low-voltage controller; there are no associated high-voltage devices or wiring. Termination is via pinned headers in the MCM4 (Figure 5) Figure 5. Typical Corresponding Numbered Positions on a Switch Plate and MCM4 Rev 2.0 1/9/2017 4

5 The DS12 assembly is powered with INNCOM s S5bus, which contains wires for power and ground, and a communication wire not used for power transfer. As Figure 5 illustrates, the S5-Bus can link the DS12 assembly to other INNCOM devices. Because the DS12 assembly can have a variable number of DS12s, the DS12 positions on the switch plate are numbered to correspond to positions on the MCM4 (Figure 5). Whatever the number or layout of DS12s in the switch plate, the position numbers will remain the same; therefore, a DS12 in position 3, for example, will always be wired to position 3 of the MCM 4. The MCM4 can support six DS12s, and the DS12s can be mounted in more than one plate. This allows flexibility in mounting because in some applications two assemblies can be served by one MCM4. Technical Specifications Voltage 12VDC Current Maximum output 31mA (see table 2) Operating Environment 40 to 150 ºF (5 to 65 ºC) Mounting 20-guage wall mount bracket and plastic framing (Both provided) Dimensions Switch plate MCM4 DS12 Switch See Figure 5. See Figure 5. See Figure 2. Approvals FCC Part 15 Current Consumption = 13 ma + N (3mA) where N is the number of DS12s connected. Table 2. Configuration Load (Includes Logic Board) 1 DS12 16mA 2 DS12 19mA 3 DS12 22mA 4 DS12 25mA 5 DS12 28mA 6 DS12 31mA Rev 2.0 1/9/2017 5

6 Figure 6. Dimensions of Switch Plate, Frame and MCM4 Ordering Options Tables 3 through 5 provide ordering options for the DS12 Barrel, Button Cap, and Decora Plate. The other components needed for the system are the Wall Mounting Plate, Framing Plate and MCM4. Refer to Figures 4 and 5 regarding the components and how they link together. DS12 Barrel LED color 1 red, 1 blue LEDs 2 red LEDs 2 blue LEDs 1 red, 1 green LEDs no LEDs (full wire harness) passive switch (no LEDs, 2-wire flying leads) customer-specified color Rev 2.0 1/9/2017 6

7 Barrel color White, black, eagle almond, chrome, brass, custom (xx) White Black Eagle Almond Chrome Brass Barrel size 7/8" length (23mm), 1 1/4" length (32mm). Note: Both lengths have diameter 5/8" (16mm). 23mm 32mm Exterior Cap clear white black eagle almond chrome brass customer-specified color Interior Cap milky (translucent) white black eagle almond chrome brass customer-specified color Note: When the exterior cap is solid, it is not necessary to specify color for the interior cap. Cap Assembly Examples White Black Eagle Almond Chrome Brass Clear Exterior Cap Colors White Black Eagle Almond Chrome Brass Interior Cap Colors Rev 2.0 1/9/2017 7

8 Configurations Materials plastic glass brass chrome custom Rev 2.0 1/9/2017 8

9 Document Revisions History Document Revision History DATE ISSUED REASON FOR CHANGE V Apr 2007 First Release V Jan 2009 Correct Dimensioning V Jan 2017 Rebranded to HON Standard The material in this document is for information purposes only. The content and the product it describes are subject to change without notice. Honeywell makes no representations or warranties with respect to this document. In no event shall Honeywell be liable for technical or editorial omissions or mistakes in this document, nor shall it be liable for any damages, direct or incidental, arising out of or related to the use of this document. No part of this document may be reproduced in any form or by any means without prior written permission from Honeywell. Copyright 2016 by Honeywell International, Inc. All Rights Reserved. Honeywell I 277 West Main Street I Niantic, CT I Phone: I Rev 2.0 1/9/2017 9