FREQUENCY CONVERTER FC102 (QUICK GUIDE)
|
|
- Melissa Sheila Floyd
- 5 years ago
- Views:
Transcription
1 FREQUENCY CONVERTER FC102 (QUICK GUIDE) INSTALLATION AND MAINTENANCE Content Page Safety instructions 2 IT system 3x230VAC 2 Connections 3 Control unit (LCP) 4 Manual operation 4 Reverse the direction of rotation 4 More information 4 Wiring diagram 5 Basic configuration 6 PID regulation 7 FläktGroup DC_9325GB _R0 Specifications are subject to alteration without notice
2 2 Installation and maintenance SAFETY INSTRUCTIONS Check that the frequency converter is correctly connected to earth. Do not pull out the mains or motor contacts or other power connections when the frequency converter is connected to the power supply grid. Protect the user from mains voltage. Protect the motor against overload in accordance with national and local regulations. The leakage currents to earth exceed 3.5 ma, see Design guide. The [Off] button is not an isolator switch. It does not disconnect the frequency converter from the mains. WARNING! Warning high voltage The frequency converter is subject to highly dangerous voltages when it is connected to the mains. Incorrect installation of the motor or frequency converter can lead to material damage, serious personal injury or death. Follow the instructions in this manual as well as local and national provisions and safety regulations. Voltage (V) WARNING! Discharge time! Frequency converters have DC bus capacitors that can hold a charge even after the mains voltage has been disconnected. Prevent electrical hazards by disconnecting the mains voltage, disconnecting permanent magnet motors and DC bus supplies, including battery backup, UPS and DC bus connections for other frequency converters. Wait until the capacitors have fully discharged before carrying out maintenance or repairs. Read more about the discharge waiting times in the table below. Starting to service or repair the unit immediately after cutting the power supply, without waiting for the specified period, can lead to death or serious personal injury. Output range (kw) Minimum waiting time (min) WARNING! Installation at heights For installation at height, contact FläktGroup regarding PELV. TAKE CARE! Residual current device: This product can cause a direct current in the protective earth conductor. When using a residual current device as additional protection, use only a type B residual current device (delayed) on the input side of this product. See also Danfoss application note for the MN90G RCD. The protective earthing of the frequency converter and the use of RCDs must always follow national and local regulations. TAKE CARE! IT system (3x230VAC) When installing the FC102 on an isolated system (IT system, 3x230VAC) set parameter to [0] Off. Press [Main Menu] twice. Navigate using the [ ] [ ] and [OK] buttons until parameter is displayed (select 14 **, then 14 5* and lastly 14 50). Set this parameter to [0] Off.
3 Installation and maintenance 3 CONNECTIONS PRINCIPLE IMAGE BB Control unit (LCP) 2 RS 485 serial bus 3 Analogue I/O LCP contact 5 Analogue switches 6 Cable support/ PE earth 7 Earthing plate 8 Earth clamp Shielded cable earth clamp and cable support 10 Motor connection Relay 1 12 Relay 2 13 Brake and load distribution terminal 14 Mains connection 15 USB Serial bus, terminal switch 8 17 Digital I/O and 24 V Cover panel
4 Info 4 Installation and maintenance CONTROL UNIT (LCP) A. Alphanumeric display The information displayed in the control unit display (LCP) can be customised. See parameters 0 20, 0 21, 0 22, 0 23 and The factory settings display: motor rpm, motor current, motor output, motor frequency and reference. B. Menu buttons Use the menu buttons to access the parameter settings, to toggle between status display modes during normal operation and to display fault log data. a a Status 1(1) 1234rpm 1.0 A 43,5Hz Run OK 43,5Hz C. Navigation and indication [Back] returns to the previous step or menu list [Cancel] Cancel the latest change or command [Info] Provides information of the function displayed [ ] [ ] [ ] [ ] navigate and increase/decrease [OK] Activate selection or access a parameter group b Status Back Quick Menu Main Menu Cancel Alarm Log Green indication power on Yellow indication warning Red indication alarm c c On Warn. OK D. Driftslägesknappar och återställning [Hand/on] Starting the motor for local control [Off] Stopping the motor [Auto/on] Allow control via control terminals or the communication bus [Reset] Resetting alarms d Alarm Hand on Off Auto on Reset MANUAL OPERATION Press [Hand/on] to start Press the navigation buttons to set the desired speed Press [Off] to stop Press [Auto/on] to return to automatic operation REVERSE THE DIRECTION OF ROTATION If necessary the direction of rotation can be reversed using parameter When connection is correct 0=clockwise and 1=anti-clockwise. MORE INFORMATION This quick guide contains the basic information needed to install and operate the frequency converter. There is more information available in the attached documentation.
5 Installation and maintenance 5 WIRING DIAGRAM L1 L2 L3 N PE F L1 L2 L3 PE Danfoss FC V V 13 DIG IN 18 DIG IN 19 COM 20 DIG IN 27 DIG IN 29 DIG IN 32 DIG IN 33 DIG IN V 50 A IN 53 A IN 54 COM 55 A OUT 42 COM 39 R2 R Relay output 0 Alarm NO/NC (Param ) Relay output 1 Start Start Reference 0 10VDC (FW standard) Actual value PID regulation Run Indicator NO/NC (Param ) Analog switches A53 12 A54 12 ON ON ON = 0-20m OFF = 0-10VDC U V W PE RS-485 com 61 RS RS The basic configuration (FläktGroup standard) relates to VDC control via terminal block 53. M To activate the internal PID regulator see page 6. The sensor is connected to terminal block 54. SIGNALS Designation Type Terminal block Start Potential-free closure Control signal VDC 53 Pressure/flow sensor VDC (4...20mA) 54 COM For analogue in (Terminal blocks 53, 54) 55 Alarm R1 NO/NC 01, 02, 03 Operation R2 NO/NC 04, 05, 06
6 6 Installation and maintenance BASIC CONFIGURATION FOR ASYNCHRONOUS MACHINES (FLÄKTGROUP STANDARD) When the frequency converter is energized for the first time the language can be selected. Obviously this can be changed later. After Smart Start is started for VDC control by pressing [ ], followed by pressing [OK]. Step Description TF FF 1 Language English English 2 Select Q3 Function Setups Asynchronous Asynchronous 3 Number of motors Thermal motor protection ETR 1 ETR 1 5 Motor Power [kw] 6 Motor Voltage 7 Motor Current 8 Motor Frequency See motor plate 9 Motor Nominal Speed 10 Minimum Reference 0 Hz 0 Hz 11 Maximum Reference Hz Hz 12 Apply on terminal block 53 Yes Yes 13 Application Fan Fan 14 Autom Energy Optimisation Yes (2, 4-pon) Yes (2, 4-pin) No (other) No (other) See motor plate 15 AMA Yes Yes 16 Confirm AMA OK OK 17 Press [Main Menu] twice 18 Select 3-** Reference / Ramps 19 Select 3-4* Ramp 1 20 [3-41] Ramp 1, Ramp Up Time 21 [3-42] Ramp 1, Ramp Down Time 30s 40s When the frequency converter is energized for the first time the language can be selected. Obviously this can be changed later. After Smart Start is started for VDC control by pressing [ ], followed by pressing [OK]. When using CentriFlow 3D, you need to enter 1-06 and change the direction of rotation to [1] inverse. Configuration carried out by Date Smart Start can be reactivated at any time. First press [Quick Menus]. Then navigate using the [ ] and [ ] buttons until the cursor is on Q4 Smart Start. Then press [OK]. Danfoss factory reset Press [Main Menu] twice. Navigate using the [ ] [ ] and [OK] buttons until parameter is displayed (select 14 **, then 14 2* and lastly 14 22). Set this parameter to [2] and then switch off the mains voltage. When the frequency converter is re-energised the parameters will have returned to their factory settings.
7 Installation and maintenance 7 ACTIVATING PID REGULATION Step Description TF FF 1 Press [Quick menus] 2 Press [Quick menus] 3 Select Q3-3 Closed Loop Settings 4 Select Q3-30 Single Zone Int.Setpoint Confi guration Mode [3] Closed Loop [3] Closed Loop Reference/Feedback Unit [72] Pa [72] Pa Minimum Reference/Feedb. 0 Pa 0 Pa Maximum Reference/Feedb. Pa Pa 9 Press [ ] once Terminal 54 Low Ref./Feedb. 0 Pa 0 Pa Terminal 54 High Ref./Feedb. Pa Pa Terminal 54 Filter Time Const 1 s 1 s 14 Press [ ] four times Setpoint 1 Pa Pa PID Normal/Inverse Control [0] Normal [0] Normal See sensor See sensor Setpoint 17 Press [ ] twice PID Start Speed PID Proportional Gain 30.0s 30.0s Adjust if necessary 20 Press [Main Menu] twice 21 Select 0 ** Operation / Display 22 Select 0 2* LCP Display Display Line 1.1 Small [1654] Feedback 1 [1654] Feedback 1 Configuration carried out by Date
8 8 Installation and maintenance MODBUS RTU IN EQ If Modbus RTU is used in eq AHU for controlling drives, they must be set according to the table below. Configuration Parameter Description Value 8-30 Protocol [2] Modbus RTU 8-31 Address Supply fan: 60 Exhaust fan: Baudrate [2] Parity / Stop bits [2] No parity, 1 Stop bit PARALLEL OPERATION When two frequency converters are to operate in parallel, one must be configured as master and the other as slave. After this, connect the two frequency converters together as indicated below. Configuration, master Parameter Description TF FF 6-50 Function, terminal block mA 4-20mA Configuration, slave Parameter Description TF FF 6-14 Output frequency equivalent to 4mA 0 Hz 0 Hz 6-15 Output frequency equivalent to 20mA Hz Hz Set switch A53 (located under the display) to position I. The power to the converter must be switched off. Connection Master Slave
FREQUENCY CONVERTER FC101 (QUICK GUIDE)
FREQUENCY CONVERTER FC101 (QUICK GUIDE) INSTALLATION AND MAINTENANCE Content Page Safety instructions 2 IT system 3x230VAC 2 Connections 3 Control unit (LCP) 4 Manual operation 4 Reverse the direction
More informationFLÄKTGROUP OFFERS A WIDE RANGE OF PER- MANENT MAGNET MOTORS (PM) AND FREQUENCY CONVERTERS FOR PLUG FANS. POWER RANGE IS FROM 0,8 KW TO 15 KW.
CENTRIFLOW PUR 3D (A, PLUG B, C, D) FAN GMPM FC101 AND SLIDE IN FREQUENCY ROTOR CASSETTE CONVERTER QUICK GUIDE FLÄKTGROUP OFFERS A WIDE RANGE OF PER- MANENT MAGNET MOTORS (PM) AND FREQUENCY CONVERTERS
More informationUser Guide VLT Parallel Drive Modules
ENGINEERING TOMORROW User Guide VLT Parallel Drive Modules 250 1200 kw vlt-drives.danfoss.com Contents User Guide Contents 1 Introduction 4 1.1 Purpose of the Manual 4 1.2 Additional Resources 4 1.3 Manual
More informationTaco System Logic (TSL)
Taco System Logic (TSL) 302-370 Installation, Operation, and Maintenance Manual SUPERSEDES: June 27, 2014 EFFECTIVE: December 21, 2015 Table of Contents 1 ELECTRICAL CONNECTIONS................. 2 1.1
More information1 Extended and Advanced Cascade Controller Option 3
VLT Operating Instructions Contents Contents Extended and Advanced Cascade Controller 3 How to read these Operating Instructions 3 High Voltage Warning 3 Safety Instructions 3 Avoid unintended Start 3
More informationSafety Instructions 1-1 Avoid unintended Start General Description 2-2
Contents Contents 1 Safety and precautions 1-1 Safety Instructions 1-1 Avoid unintended Start. 1-1 2 Introduction 2-1 General Description 2-2 3 Supported Configuration 3-1 Introduction 3-1 Fixed-speed
More informationAF-600 FP TM Fan & Pump Drive. (230V to 60HP, 460/575V to 125HP Operating Instructions
GE AF-600 FP TM Fan & Pump Drive (230V to 60HP, 460/575V to 125HP Operating Instructions Safety Safety WARNING HIGH VOLTAGE! Frequency converters contain high voltage when connected to AC mains input power.
More informationMetasys N2 Instruction Manual VLT Adjustable Frequency Drive. 12/ Revision B
Metasys N2 Instruction Manual VLT 6000 Adjustable Frequency Drive 12/99-6110-00 Revision B 2 Table of Contents Overview Page Introduction... 5 About this Manual... 5 References... 5 Instructions Abbreviations
More informationOperating Instructions Extended Cascade Controller MCO 101
Operating Instructions Extended Cascade Controller MCO 101 VLT AQUA Drive FC 200 Extended Cascade Controller Option Contents Contents 1. Safety and precautions 3 Safety Instructions 3 Avoid unintended
More informationMAKING MODERN LIVING POSSIBLE. VLT AQUA Drive Cascade Controller Options MCO 101/102 Operating Instructions
MAKING MODERN LIVING POSSIBLE VLT AQUA Drive Cascade Controller Options MCO 101/102 Operating Instructions Safety VLT AQUA Drive MCO 101/MCO 102 Safety WARNING HIGH VOLTAGE Frequency converters contain
More informationVacon HVAC100 Commissioning Guide
Vacon HVAC100 Commissioning Guide INDEX 1. Glossary of terms 2. Wiring diagrams 3. Set up procedures a. Motor settings input b. Low level start, analogue input speed reference in AUTO position. Low level
More informationControl system for rotary heat exchanger EQRB, L=3,4
Installation instructions, drive system EQRB, L=3.4 sizes 005-072 General description A speed controlled drive system specifically adapted to drive rotary heat exchangers. No tuning is necessary. All control
More informationInstallation Instructions
Installation Instructions Variable Frequency Drive (VFD) 7 ½ - 25 Ton Units with 2 Wire Control WARNING UNINTENDED EQUIPMENT OPERATION Modifying or changing parame eters whose function is not described
More informationInstallation and Wiring Instructions... 9
Contents Safety and precautions... 3 Safety regulations... 4 Warning against unintended start... 4 Operation modes... 6 Cascade Control Operation... 6 Standard Cascade Control Mode... 7 Lead Pump Alternation...
More informationINGERSOLL RAND Fixed Speed/Variable Speed Conversion COMMISSIONING AND OPERATION MANUAL
INGERSOLL RAND Fixed Speed/Variable Speed Conversion COMMISSIONING AND OPERATION MANUAL Before installing or starting this unit for the first time, this manual should be studied carefully to obtain a working
More informationAF-60 LP TM Micro Drive. Programming Guide
GE AF-60 LP TM Micro Drive Programming Guide Contents Contents 1 Safety 1-1 1.1.1 High Voltage Warning 1-1 1.1.2 Safety Instructions 1-1 1.1.3 Software Version and Approvals 1-1 1.1.4 General Warning 1-1
More informationP216. Condenser fan speed controller. Product bulletin. Features
P216 Condenser fan speed controller Product bulletin These controllers are designed for speed variation of single phase motors, especially for fan speed control on air cooled condensers. Head pressure
More informationTPE, TPED Series 2000
GRUNDFOS INSTRUCTIONS TPE, TPED Series 2000 Installation and operating instructions English (GB) English (GB) Installation and operating instructions Original installation and operating instructions. CONTENTS
More informationEQ5 SERIES Quick Start Guide for Constant Torque Applications
EQ5 SERIES Quick Start Guide for Constant Torque Applications PN EQ5QSCT, Revision: 0.02, April 4 th 2009 EQ5 Drive Quick Start Guide for Constant Torque Applications Contents Page Introduction... 3 1.
More informationOperating Instructions
MAKING MODERN LIVING POSSIBLE Operating Instructions VLT DriveMotor FCP 106 and FCM 106 Metasys N2 www.danfoss.com/drives Contents Contents 1 Introduction 2 1.1 Purpose of the Manual 2 1.2 Additional
More informationMAKING MODERN LIVING POSSIBLE. Instruction VLT HVAC Basic Drive Cascade Controller
MAKING MODERN LIVING POSSIBLE Instruction VLT HVAC Basic Drive Cascade Controller 1.1 Cascade Controller Constant Speed Pumps (2) Variable Speed Pumps (1) Motor starter Illustration 1.1 Cascade Controller
More informationGenset control and protection with safety system
APPLICATION NOTES Generator Protection Unit, GPU-3 APPLICATION NOTES Genset control and protection with safety system Application description Functional description Wiring I/O lists Basic setup Flowcharts
More informationSMVector Additional I/O Module Installation and Operation Manual
SMVector Additional I/O Module Installation and Operation Manual About These Instructions This documentation applies to the optional Additional I/O module for the SMVector inverter and should be used in
More informationAC Variable Speed Drive 0.75kW 250kW / 1HP 350HP Volt 1 & 3 Phase. Advanced User Guide Revision 2.00
AC Variable Speed Drive 0.75kW 250kW / 1HP 350HP 200 480 Volt 1 & 3 Phase Advanced User Guide Revision 2.00 Optidrive P2 Advanced User Guide Rev 2.00 Optidrive P2 Parameter Set Overview 1 This Document
More informationStandard Cascade Controller Setup... 38
Contents Safety and precautions... 3 Safety regulations... 4 Warning against unintended start... 4 Operation modes... 6 Cascade Control Operation... 6 Standard Cascade Control Mode... 7 Master/Slave Cascade
More informationVLT Line Filter MCC 107 EMC Filter Series VLT Midi Drive FC 280 (K1 K3)
These instructions provide technical and installation information for the MCC 107 EMC filter series. Only Danfoss qualified personnel is allowed to install this equipment. The personnel must be familiar
More informationModbus RTU Option Card for VLT 5000/6000 Adjustable Frequency Drive
Modbus RTU Option Card for VLT 5000/6000 Adjustable Frequency Drive VLT is a registered Danfoss trade mark MG.10.P2.22 1 Rotating shafts and electrical equipment can be hazardous. Perform all electrical
More informationAC Variable Speed Drive 0.75kW 250kW / 1HP 350HP Volt 1 & 3 Phase. Advanced User Guide Revision 1.10
AC Variable Speed Drive 0.75kW 250kW / 1HP 350HP 200 480 Volt 1 & 3 Phase Advanced User Guide Revision 1.10 Optidrive P2 Parameter Set Overview 1 This Document is for use with version 1.20 Firmware. Advanced
More informationDXTH DUCT SENSOR / SWITCH FOR TEMPERATURE AND HUMIDITY. Mounting and operating instructions
DUAL DUCT SENSOR / SWITCH FOR TEMPERATURE AND HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL
More informationMAKING MODERN LIVING POSSIBLE. Quick Guide. VLT HVAC Basic Drive Cascade Control *MG18F102*
MAKING MODERN LIVING POSSIBLE www.danfoss.com/drives Quick Guide VLT HVAC Basic Drive Cascade Control 30R0265 MG8F02 *MG8F02* Rev. 20-03-22 Contents Contents Quick Guide 2. Safety 2.. Warnings 2..2 Safety
More informationControl D. Controller Module for Proportional Valve Control. Installation Manual
Control D Controller Module Table of Contents Control D 1 1.1 1.2 1.3 1.3.1 1.3.2 1.4 2 3 4 5 5.1 5.2 5.3 6 7 8 Description 3 How To Order 3 Operating Elements 3 Adjustment 4 Operation 4 Auto-adapt 4 Operating
More informationOptidrive Applications Support Library
Optidrive Applications Support Library Application Note Title AN-ODV-3-038 Related Products Optidrive Eco Overview Level 3 Modbus RTU Control and Register Mapping 1 Fundamental - No previous experience
More informationQ9 ASD LOW VOLTAGE DRIVE
ASD LOW VOLTAGE DRIVE HVAC-MINDED, SYSTEM FRIENDLY RELIABLE Toshiba has manufactured pulse-width modulated drives since 1981 and is one of the few companies that manufactures both motors and drives in
More information1. Safety Danger Warnings Earthing and earth fault protection... 4
vacon 1 INDEX Document: DPD00386A Version release date: 24.9.10 1. Safety... 2 1.1 Danger... 2 1.2 Warnings... 3 1.3 Earthing and earth fault protection... 4 2. Metasys N2 - general info... 5 3. N2 technical
More information4.7 Digital Input/Output Module 07 DC digital inputs, 8 digital outputs, 8 configurable inputs/outputs, 24 V DC, CS31 system bus
4.7 Digital Input/Output Module 16 digital inputs, 8 digital outputs, 8 configurable inputs/outputs, 4 V DC, CS31 system bus 1 3 Advant Controller 31 I/O Unit ERR Test 4 1 Fig. 4.7-1: Digital input/output
More informationNICOTRA Gebhardt EKE E-IM EKE E-IM S. Operating manual EC-Controller BA-EKE /2012
Operating manual EC-Controller EN BA-EKE 2.04 01/2012 EKE 07-0065-5E-IM EKE 07-0065-5E-IM S Warning Before installing and commissioning the EC-Controller, you must read all safety instructions and warnings
More informationOperating Instructions
Operating Instructions VLT Micro Drive FC 51 VLT Micro Drive FC 51 Operating Instructions Contents Contents 1. Safety 5 Safety Instructions 5 Approvals 5 General Warning 5 Avoid unintended Start 6 Before
More informationP216 Series Condenser Fan Speed Controller
P216 Series Condenser Fan Speed Controller Installation Instructions P216xxx-x Part No. 24-85895-18, Rev. D Issued 27 August 2015 Applications Refer to the QuickLIT website for the most up-to-date version
More informationGenset Controller Unit Model EMS - GC10. Installation Manual Section
Genset Controller Unit Model EMS - GC10 Installation Manual 00-02-0794 Section 75 2013-01-28 In order to consistently bring you the highest quality, full featured products, we reserve the right to change
More informationWARNING ELECTRICAL SHOCK HAZARD
Description Safety Instructions The top-entry sub D9 connector kit is designed for enclosure sizes D1h D8h, E1 E2, and E1h E4h with VLT PROFIBUS DP MCA 101 option. It fits the following drives: VLT HVAC
More informationSetpoint Isolators. Technical Manual. HA Issue Parker SSD Drives, a division of Parker Hannifin Ltd. WARRANTY
Technical Manual HA09 Issue 008 Parker SSD Drives, a division of Parker Hannifin Ltd. All rights strictly reserved. No part of this document may be stored in a retrieval system, or transmitted in any form
More informationUMG 20CM. 20 Channel Branch Circuit Monitoring Device with RCM
20 Channel Branch Circuit Monitoring Device with RCM RCM Harmonics via analysis channel Alarm management GridVis Analysis software 20 current channels Interfaces / communication RS485 RTU Accuracy of measurement
More informationADC7520 SERIES. 1600W Battery Chargers and Power Supplies
ADC7520 SERIES 1600W Battery Chargers and Power Supplies Wide output adjustment range 0 72VDC Analog control by external 0-5VDC voltage Temp.comp charging, sense as on option Power fail relay alarm Master-Slave
More informationCompact Genset Controller, CGC 400 What's in the delivery? The first steps Push-buttons and LEDs
QUICK START GUIDE Compact Genset Controller, CGC 400 What's in the delivery? The first steps Push-buttons and LEDs DEIF A/S Frisenborgvej 33 DK-7800 Skive Tel.: +45 9614 9614 Fax: +45 9614 9615 info@deif.com
More informationUnidrive M400 (Frame 1 to 4) Quick Start Guide
This guide is intended to provide basic information required in order to set-up a drive to run a motor. For more detailed installation information, please refer to the Unidrive M400 User Guide which is
More information1/32-DIN TEMPERATURE CONTROLLER INSTALLATION, WIRING AND OPERATION MANUAL FORM 3882
1/32-DIN TEMPERATURE CONTROLLER INSTALLATION, WIRING AND OPERATION MANUAL FORM 3882 This manual is intended for use in support of installation, commissioning and configuration of the 1/32-DIN Temperature
More informationGRUNDFOS INSTRUCTIONS. Control MPC. Installation and operating instructions
GRUNDFOS INSTRUCTIONS Control MPC Installation and operating instructions English (GB) English (GB) Installation and operating instructions Original installation and operating instructions CONTENTS Page
More informationMAKING MODERN LIVING POSSIBLE. Quick Guide VLT HVAC Basic Drive
MAKING MODERN LIVING POSSIBLE Quick Guide VLT HVAC Basic Drive Contents Contents Quick Guide 2. Safety 2.. Warnings 2..2 Safety Instructions 2.2 Introduction 2.2. Available Literature 2.2.2 Approvals 2.2.3
More informationRXTP ROOM TEMPERATURE
ROOM TEMPERATURE CONTROLLER WITH PI CONTROL Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4
More informationUnidrive M200, M201 (Frame 1 to 4) Quick Start Guide
This guide is intended to provide basic information required in order to set-up a drive to run a motor. Please refer to the Unidrive M200 / M20 User Guide which is available to download from www.controltechniques.com/user
More information2 Table of Contents 1. TABLE OF CONTENTS. 1. Table of Contents Introduction Wiring Diagram Terminals Review...
TPR-6 Temperature Protection Relay Instruction Manual Ver. June 1 st 2010 2 Table of Contents 1. TABLE OF CONTENTS 1. Table of Contents... 2 2. Introduction... 3 3. Wiring Diagram... 5 4. Terminals Review...
More informationSMVector Additional I/O Module Installation and Operation Manual
SMVector Additional I/O Module Installation and Operation Manual About These Instructions This documentation applies to the optional Additional I/O module for the SMVector inverter and should be used in
More informationINSTALLATION DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER. Before installation:
DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER The DKM-409 is a precision instrument designed for displaying various AC parameters in 3-phase distribution panels. Thanks to its isolated
More informationOptidrive Applications Support Library
Optidrive Applications Support Library Application Note Title AN-ODE-3-038 Related Products Optidrive E3 Overview Level 3 Modbus RTU Control and Register Mapping 1 Fundamental - No previous experience
More informationI/O module (Expansion module)
I/O module (Expansion module) Variomat Variomat Giga Reflexomat Servitec V2.00 02.02.2015 GB Operating manual Original operating manual English I/O module (Expansion module) Contents 02.02.2015 Contents
More information1.1.1 Software Version Introduction About this Manual References 2
Contents Contents 1 Overview 2 1.1.1 Software Version 2 1.1.2 Introduction 2 1.1.3 About this Manual 2 1.1.4 References 2 2 Instructions 3 2.1.1 Abbreviations and Definitions 3 2.1.2 Network Connection
More informationMonitoring Technique. VARIMETER PRO Multifunction Measuring Relay MK 9300N, MH 9300
Monitoring Technique VARIMETER PRO Multifunction Measuring Relay MK 93N, MH 93 268581 Product description MK 93N MH 93 The universal measuring relays MK 93N / MH 93 of the VARIMETER PRO series monitor
More informationDrive Technology \ Drive Automation \ System Integration \ Services. Manual. Control Cabinet Inverter MOVITRAC B Functional Safety
Drive Technology \ Drive Automation \ System Integration \ Services Manual Control Cabinet Inverter MOVITRAC B Functional Safety Edition 05/2009 16811216 / EN SEW-EURODRIVE Driving the world Content Content
More informationVoltsys Inverter Control Unit
Voltsys Inverter Control Unit Coomanore North, Bantry, info@voltsys.com Co. Cork. Republic of Ireland tel. +353 (0) 27 52773 Contents Important Safety Instructions... 3 Controller Layout & Wiring... 4
More informationStandard Options. Model 4100 Position Indicating Meter. Three Phase Motor Control. Positran Transmitter
Standard Options Model 4100 Position Indicating Meter A percent-of-full-travel meter is supplied with a trim potentiometer resistor, terminal block and connectors. A potentiometer is required in the actuator
More informationOperating Instructions. Modbus RTU VLT 2800 VLT 6000 VLT 8000
Operating Instructions Modbus RTU VLT 2800 VLT 6000 VLT 8000 Contents Overview... 6 Introduction... 6 About This Manual... 6 Assumptions... 6 What You Should Already Know... 6 Modbus RTU Overview... 6
More informationQUICK START GUIDE. vau4/3. Frequency converter. operating instructions /12
operating instructions QUICK START GUIDE Frequency converter vau4/3 28100241101 12/12 1 Safety information Warning of electrical shock! Danger to life! Electrical shock can cause serious injury or even
More informationContents. Index 35. VLT HVAC Drive Metasys N2
VLT HVAC Drive Metasys N Contents Contents Introduction 3 About this Manual 3 References 3 Abbreviations and Definitions 5 Network Connection 5 Hardware Set-up 5 VLT Parameters 7 Analog s (AI) 3 Binary
More informationMonitoring technique. VARIMETER Voltage relay MK 9064N, MH 9064
Monitoring technique VARIMETER Voltage relay MK 9064N, MH 9064 0269462 Your Advantages Preventive maintenance For better productivity Quicker fault locating Precise and reliable Min-, Max. value or window
More informationQUICK START GUIDE Generator Paralleling Controller, GPC-3 Generator Protection Unit, GPU-3/GPU-3 Hydro Paralleling and Protection Unit, PPU-3
QUICK START GUIDE Generator Paralleling Controller, GPC-3 Generator Protection Unit, GPU-3/GPU-3 Hydro Paralleling and Protection Unit, PPU-3 What's in the delivery? Getting started The first steps PC
More informationDigital DRIVE for Brushless motor MD Serial
Digital DRIVE for Brushless motor MD Serial Installation guide Read manual before installing and respect all indications with this icon: MD-GI/EN Table of Contents 1- Introduction... 3 1-1- Warning...
More informationRXTH DUAL ROOM SENSOR / SWITCH
DUAL ROOM SENSOR / SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE
More informationPROGRAMMING MANUAL IM262R00. AQUAVAR Intelligent Pump Controller START-UP GENIE PROGRAMMING MANUAL
PROGRAMMING MANUAL IM262R00 AQUAVAR Intelligent Pump Controller START-UP GENIE PROGRAMMING MANUAL TABLE OF CONTENTS Introduction 3 Chapter 1: Motor 4 Chapter 2: Application 5 2.1. Single Pump 5 2.2. Constant
More informationTachometer Panel, PE3
Features Plug-n-play units with factory programmed parameters 4-20 ma feedback signal Isolated relay alarm outputs Frequency input Diagnostic indicators NEMA 4 Enclosure Model PE3, Tachometer Panel Benefits
More informationMVS RAIL ELECTRONIC FAN SPEED CONTROLLER. Mounting and operating instructions
DIN RAIL ELECTRONIC FAN SPEED Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5 WIRING
More informationisma-b-fcu FCU Hardware User Manual Global Control 5 Sp. z o.o. Warsaw, Poland
isma-b-fcu User Manual FCU Hardware Global Control 5 Sp. z o.o. Warsaw, Poland www.gc5.pl Table of contents 1 Introduction 3 1.1 Document change log 3 1.2 Safety rules 3 1.3 Technical specifications 4
More informationOptidrive VTC Modbus RTU Register Map
Application Note AN-VTC- 39 Optidrive VTC Modbus RTU Register Map Author: Ning Xu, Invertek Drives Ltd Revision: 2.21 6 September 2006 General This document details the Modbus RTU memory mapping implemented
More informationMetasys N2 Communications Protocol Operating Instructions
Metasys N2 Communications Protocol Operating Instructions TR200 BAS-SVX26A-EN November 2009 BAS-SVX26B-EN Table of Contents Safety 1-1 High voltage warning 1-1 Before commencing repair work 1-4 Special
More informationDeviceNet Drive Profile CFW-09
Motors Automation Energy Transmission & Distribution Coatings DeviceNet Drive Profile CFW09 Communication Manual DeviceNet Drive Profile Communication Manual Serie: CFW09 Language: English Software Version:
More informationTR150 DRIVE STANDARD FEATURES
TR150 DRIVE STANDARD FEATURES The TR150 Drive The TR150 Drive Series is a microprocessor-based, high frequency IGBT-based, PWM AC drive with control functions and software designed solely for the unique
More informationSupported Modbus RTU Function Codes... 26
å Contents Overview... 5 Introduction... 5 About This Manual... 5 Assumptions... 5 What You Should Already Know... 5 Modbus RTU Overview... 5 VLT 2800 and VLT 6000 with Modbus RTU... 6 Installation and
More informationOPERATING INSTRUCTION
OPERATING INSTRUCTION AUTORANGING MULTIMETER MAX Ω F C 10A MAX every 15 min. COM V SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation
More informationPeristaltic Cased Tube Pump
Peristaltic Cased Tube Pump Selectable Output Control Functionality and Setup Version 1.0v-11/2016 Print-No. 01 Table of Contents 1. Introduction 2. Powering the Input/Output Port 2.1 Wiring for Local
More informationD115 The Fast Optimal Servo Amplifier For Brush, Brushless, Voice Coil Servo Motors
D115 The Fast Optimal Servo Amplifier For Brush, Brushless, Voice Coil Servo Motors Ron Boe 5/15/2014 This user guide details the servo drives capabilities and physical interfaces. Users will be able to
More information1 How to Read these Operating Instructions 3. 3 Introduction to MCF 106 A/ B in C Option Adaptor 7
MCF 106 A/ in C Option Adaptor Instruction Contents Contents 1 How to Read these Operating Instructions 3 Available Literature for VLT AutomationDrive FC 300 3 Approvals 4 Symbols 4 Abbreviations 4 2 Safety
More informationDIRIS D-30 DIRIS Digiware D-40 DIRIS Digiware D-50 Control and power supply interface
USER MANUAL DIRIS D-30 DIRIS Digiware D-40 DIRIS Digiware D-50 Control and power supply interface EN www.socomec.com/ en/diris-d EN CONTENTS 1. DOCUMENTATION....3 2. HAZARDS AND WARNINGS....4 2.1. Risk
More informationVLT 8000 AQUA. Installation. Mechanical installation
Mechanical installation Please pay attention to the requirements that apply to integration and field mounting kit, see the below list. The information given in the list must be observed to avoid serious
More informationProgramming Guide VLT BACnet/IP MCA 125
ENGINEERING TOMORROW Programming Guide VLT BACnet/IP MCA 125 VLT HVAC Drive FC 102 vlt-drives.danfoss.com Contents Programming Guide Contents 1 Introduction 2 1.1 Purpose of the Manual 2 1.2 Additional
More informationGV3000/SE Operator Interface Module (OIM) User Guide Version 2.0 M/N 2RK3000
GV3000/SE Operator Interface Module (OIM) User Guide Version 2.0 M/N 2RK3000 Instruction Manual D2-3342-2 The information in this manual is subject to change without notice. Throughout this manual, the
More informationPower Connections: Basic Wiring:
Power Connections: The CFW10 Quick Start Guide is a supplement to help get the CFW10 started quickly using the most common installation and configuration options. This CFW10 Quick Start Guide is not meant
More informationPumpDrive. Self -cooling, motor-independent frequency inverter. Brief Instructions
Brief Instructions PumpDrive 4070.801/2--11 Self -cooling, motor-independent frequency inverter Mounting variants: Motor mounting (MM) Wall mounting (WM) Cabinet mounting (CM) Brief Instructions 1 About
More informationMCH Series Drives Metasys N2 Communications Guide
MCH Series Drives Metasys N2 Communications Guide About These Instructions This documentation applies to the use of an MCH Series Variable Frequency Drive with Metasys N2 protocol and should be used in
More informationIso DIN. User Manual. 1 channel Earth Fault Monitoring
Page 1 of 5 2017 03 20 User Manual Iso DIN Iso DIN User Manual 1 channel Earth Fault Monitoring Megacon AB Ranhammarsvägen 20 S 168 67 Bromma Sweden Tel: 08 402 42 50 sales@megacon.se www.megacon.se eee
More informationTECO L510 Inverter. Quick Start Guide. Step 1. Supply & Motor connection
Quick Start Guide TECO L510 Inverter This guide is to assist you in installing and running the inverter and verify that it is functioning correctly for it s main and basic features. For detailed information
More information3GV M Modbus RTU Register Map
Application Note AN-ODP- 38 3GV M Modbus RTU Register Map Author: Ning Xu, Invertek Drives Ltd Revision: 2.21 15 June 2007 General This document details the Modbus RTU memory mapping implemented in Optidrive
More informationvacon 20 vacon 20 x vacon 20 cp ac drives modbus rtu user manual
vacon 20 vacon 20 x vacon 20 cp ac drives modbus rtu user manual vacon 1 Table of Contents Document: DPD01925A Version release date: 30.5.17 1. Safety...2 1.1 Danger...2 1.2 Warnings...3 1.3 Earthing
More informationDriveWare. User s Guide DriveConfig
DriveWare User s Guide DriveConfig DriveConfig User s Guide 3AFE68910897 Rev B EN EFFECTIVE: 1.2.2008 2008 ABB Oy. All rights reserved. 5 Table of contents Table of contents...5 Introduction to the manual...7
More informationAC Variable Speed Drive 0.75kW 250kW / 1HP 350HP Volt 1 & 3 Phase. Advanced User Guide Issue 06
AC Variable Speed Drive 0.75kW 250kW / 1HP 350HP 200 480 Volt 1 & 3 Phase Advanced User Guide Issue 06 About this Advanced Technical Manual 1 Revision History Issue Note Section Date 1.00 First Release
More informationVLT 6000 Start-Up. Oct 2003
VLT 6000 Start-Up 1 This presentation deals with the start-up of the Danfoss Drives VLT 6000 Variable Frequency Drive (VFD). It is designed to help you handle the start-up of the drive in normal applications.
More informationCompressor Controller MAM 890
Compressor Controller MAM 890 OPERATION MANUAL Revision 1.0 04.08.2017 Notice Please read all the operation manual before operating the set and keep this manual for further reference. Installation of MAM
More informationQUALITY POWER SOLUTIONS BACKED UP BY REAL-WORLD ENGINEERING EXPERIENCE
QUALITY POWER SOLUTIONS BACKED UP BY REAL-WORLD ENGINEERING EXPERIENCE User s Manual SR250HL Power Supply/ Float Charger for Lead Acid Batteries STANDARD FEATURES OPTIONAL FEATURES 3 Relay Alarms-Form
More informationHTTL Speed Feedback Communications Option
HTTL Speed Feedback Communications Option Technical Manual HA467152U001 Issue 7 Compatible with Version 1.x Software - 690+ Compatible with Version 5.x Software - 605C Copyright 2010 Parker Hannifin Ltd
More informationVoltsys Inverter Control Unit
Voltsys Inverter Control Unit Coomanore North, Bantry, info@voltsys.com Co. Cork. Republic of Ireland tel. +353 (0) 27 52773 Contents Important Safety Instructions... 3 Controller Layout & Wiring... 4
More informationTR200 DRIVE STANDARD FEATURES
TR200 DRIVE STANDARD FEATURES The TR200 Trane Drive The TR200 Drive Series is a microprocessorbased, high frequency IGBT-based, PWM AC drive with control functions and software designed solely for the
More informationOPERATOR'S MANUAL Generator Paralleling Controller, GPC-3 - Generator Protection Unit, GPU-3/GPU-3 Hydro - Paralleling and Protection Unit, PPU-3
OPERATOR'S MANUAL Generator Paralleling Controller, GPC-3 - Generator Protection Unit, GPU-3/GPU-3 Hydro - Paralleling and Protection Unit, PPU-3 Display and push-button functions Alarm handling Log list
More information