EP-ELVCTL Elevator Control (NION-16C48M)

Transcription

1 EP-ELVCTL Elevator Control (NION-16C48M) Product Installation Document This document covers the procedures and specifications for installing the above listed unit and when appropriate, information regarding configuration on the monitored device. For more detailed configuration and operation information, refer to the UniGuard Manual as appropriate. Description of the NION-16C48M Similar in function to the NION-2C8M, the NION-16C48M (16 Control, 48 Monitor) is a discrete input/output interface used on the network. When used for elevator control, the NION-16C48M becomes an extension of a 2DRN connected to the UniGuard application. UniGuard provides the configuration interface for elevator control functionality. The 16C48M communicates with a 2DRN via a serial cable connecting the two boards. Actual configuration of the elevator control software is within the UniGuard application. The NION-16C48M can be powered by any 24VDC power limited source with battery backup which is UL listed for use with fire protective signaling units; however, an optional MPS24BRB power supply is available. Power must be supervised or placed within 20 ft of the NION with connections run in conduit. The NION-16C48M mounts in an enclosure (NIS CAB-3) with conduit knockouts. It cannot be rack mounted. Serial Connection of 2DRN and 16C48M Elevator Control NION The 2DRN connects and communicates with the 16C48M using the plug-in serial ports as shown below: 2DRN Serial Connection Port 16C48M Serial Connection Port 2DRN 16C48M 1 No Connect 1 No Connect 2 Transmit 2 Transmit 3 Ground 3 Ground 4 Ground 4 Ground 5 Receive 5 Receive 6 No Connect 6 No Connect 2DRN 16C48M 2DRN/16C48M Serial Cable Connectionand Pin-Out Diagram NOTE: When connecting the 2DRN and the 16C48M, the transmit pin on one should connect to the receive pin on the other, and vice versa. Document /1/2000 Rev A 51363:A ECN

2 The NION-16C48M is designed to be wired to control panels through plug-in terminal strips. The NION-16C48M has the following features: Control outputs are SPDT relays rated at 30 VDC. Powered from a UL listed power supply (optional), the monitored UL listed control panels or an auxiliary power supply which is power limited, supervised and UL listed for use with fire protective signaling units. Status, service, input and output LEDs. Transformer coupled network connection using SMX style transceivers. Software configurable from UniGuard. Transient protection to 2400V on all terminals. Included wall mount enclosure (NIS CAB-3). NION Components The following illustration displays components included and required to install a 16C48M on the network. All of these items must be ordered separately. NOTE: Line cord not included. 16C48MTB Terminal Boards Each NION comes with two terminal boards which mount directly on the mother board with stand-offs. These boards provide terminal connections to controlled outputs. 16C48M Mother Board The NION motherboard contains all relays, LEDs, CPU, configuration jumpers, firmware and terminal board connections. Transformer Assembly One 4000TA, 110VA transformer and connector. NIS CAB-3 The NION-16C48M mounts in a locking cabinet with a Lexan dress plate. (12.25"H X 9.25"W X 2.75"D) MPS24BRB Power Supply (optional) The MPS24B supplies 2.0A of 24VDC regulated power to operate the NION. Up to 200mA of resettable auxiliary power is also available. This supply contains an integral battery charger which can support 6.5 to 17AH batteries. Batteries The cabinet provides space for 12AH batteries. To use 17AH capacity batteries use the BB-17 battery box. 2

3 Installation Requirements The NION-16C48M can be installed in the following environmental conditions: Temperature range of 0ºC to 49ºC (32 F F). 93% humidity non-condensing at 30ºC (86 F). NIS-CAB3 The NION-16C48M comes standard with a wall mount enclosure, the NIS-CAB3. This enclosure has a locking door and mounting hardware for the 16C48M assembly (motherboard, terminal boards and network transceiver), MPS24BRB power supply (optional), transformer and batteries. Mounting the enclosure to its wall position 1) Use the provided key to unlock the enclosure cover. 2) Remove the enclosure cover. 3) Mount the enclosure to the wall. Refer to the enclosure mounting hole layout below. 4) Mount the optional MPS24BRB power supply and transformer to the stand-offs in the back of the cabinet using the provided hardware. 5) Mount the 16C48M motherboard to the mounting rails in the same manner. Mounting Location The NION-16C48M is designed to be installed on a wall within 20 feet of the monitored equipment in the same room. The type of hardware used is at the discretion of the installer, but must be in accordance with local code requirements. 3

4 NION Power Requirements The NION-16C48M can be powered by an optional MPS24BRB power supply. The MPS24BRB uses 110VAC, 1.8A(max.) of power and provides 2.0A of 24VDC power and battery backup in accordance with local code requirements. The MPS24BRB contains a built in battery charging circuit capable of supporting 6.5 to 17AH 24VDC batteries. Alternately, the NION can be powered by any power limited 24 VDC source which is UL or ULC listed, as appropriate for your area, for use with fire protective signaling units. For replacement part orders specify MPS24BRB for Replacement Board. Power connections from the MPS24BRB to the NION must be as follows: TB1 on the 16C48M motherboard to pins 3 and 4 of TB2 on the MPS24B. Terminals on both boards are labelled for proper connections. Normally Closed Trouble Contacts Contacts open when the main power supply enters a trouble condition. Removal disables battery charging. Cut JP1 to make auxiliary power non-resettable. Do not cut. Transformer Connection Not Used AC Power Reset Secondary Power 27.6VDC, 6.5 to 17AH. Supervised and power-limited. Fast charge = 0.75 amps (typical), trickle charge = 20mA (typical). Battery - Battery + Common +24VDC NION Power Circuit is power-limited, RMS-regulated, non-resettable, 2.0 amps max. - + Auxiliary 24VDC Power 200mA max. Power limited, filtered, regulated and resettable. Hot Neutral Earth/Service Ground Primary Power 110VAC, 1.8 amps max. Earth Ground Connect to chassis with a grounding cable assembly (Cable #71073). Optional MPS24BRB Power Supply NOTE: Always remove power from the NION before making any changes to switch settings and removing or installing option modules, SMX network modules and software upgrade chips or damage may result. 4

5 Output Configuration The NION-16C48M provides 16 SPDT relay outputs. The relays are rated at 30VDC. They can be configured for normally open or normally closed operation. All rated loads are resistive. Inductive and tungsten loads will be lower. For special applications, consult with a NIS applications engineer. Output relays are located at the bottom of the 16C48M motherboard and correspond (from left to right) to outputs one through sixteen. Above each relay is its related LED and below is a corresponding jumper to set the output for normally open or normally closed operation. Refer to the diagram below for jumper settings. Output LED 16C48M Motherboard Output Relay (Typical) Output Relays 1-16 Pin 1 Pin 3 Output Operation Jumper Set the jumper across pins 1 and 2 for normally closed operation. Set the jumper across pins 2 and 3 for normally open operation. Output Relays and NC/NO Jumper Settings For information on output LED function, refer to section NION-16C48M Operation. For information on output terminal connections, refer to section NION-16C48MTB Terminal Boards. 5

6 NION-16C48MTB Terminal Boards The Terminal Boards The NION-16C48M incorporates two terminal daughter boards which are mounted directly to the motherboard using included stand-offs. Both terminal boards are identical and interchangeable. Each terminal board is connected to the motherboard via included ribbon cables (four per terminal board). Point designation for each terminal is determined by the position of the terminal board on the motherboard. Refer to the diagrams below for terminal board mounting and ribbon cable connections. For elevator control, only two ribbon cables per teminal board are required. Terminal Board 1 Terminal Board 2 This stand-off is also used to attach the motherboard to the cabinet. Cable Sockets P1 - P4 Cable Sockets P1 - P8 16C48MTB Terminal Board Mounting Ribbon cables have universal ends and are keyed for proper connection. The motherboard has eight cable sockets, P1 through P8. Each terminal board has four sockets labelled P1 through P4. Terminal board one (T1) is mounted on the left and terminal board two (T2) is mounted on the left. The chart below maps the motherboard sockets to the terminal board sockets. Motherboard Socket Terminal Board Terminal Socket P1--NOT USED T1 P1--NOT USED P2--NOT USED T1 P2--NOT USED P3 T1 P3 P4 T1 P4 P5--NOT USED T2 P1--NOT USED P6--NOT USED T2 P2--NOT USED P7 T2 P3 P8 T2 P4 Ribbon Cable Mapping 6

7 Input / Output Connections Each terminal board has four rows of plug-in screw terminal connectors to land input and output points. All inputs are rated at 5VDC nominal, 2.5mA maximum current and 500 ohms maximum resistance. The inputs and outputs map to the connectors as described by the following diagrams: Terminal Board 1 Terminal Board 2 Inputs 1-8 Inputs Inputs 9-16 Inputs Inputs Inputs Outputs 1-8 Outputs 9-16 P1 P4 P1 P4 P2 P3 P2 P3 P1 and P2 of the terminal boards are not used. Inputs are not used. Output Terminals (A - H represent any 8 outputs) A B C D E F G H Terminal Output Mapping NOTE: In elevator control applications, the input points are not functional. Only OUTPUTS are used. Use only wire for power limited systems. Power limited wire runs use type FPLR, FPLP, FPL or equivalent cabling per NEC