8K STATIC RAM. Instruction Manual Issued Jan., 1979
|
|
- Ruby Craig
- 5 years ago
- Views:
Transcription
1 8K STATC RAM BOAD la-lll0 nstruction Manual ssued Jan., 1979 THACA AUDO 1979 ALL RGHTS QESEQV3D
2 BOARD CONSTRUCTON Begin construction of the 8K memory board by first examining it for obvious shorts. Measure with an ohm meter between all address lines, data lines and the ground and +5 volt lines for possible shorts. The sockets are the first item that should be soldered into the PCB. Notice the orientation of the C's against the layout and the silkscreen. All chips are orientated with the Pin 1 on the left side of the C. After installing the sockets, the capacitors may be soldered in next. Begin with C9 (47 uf) and CO,C (0.001 uf). The remaining caps are 0.1 ufo The dip switch should be installed after the caps. Now the board should be checked with an ohm meter for possible solder bridges and shorts again as before. f none are found you may proceed. nstall the resistors, diodes and the four regulators. Heatsink compound is not required. Use 6-32 x 3/8 screws and nuts to secure the regulators. Be cautious for the correct orientation of the diodes. POWER ON CLEAR The jumper option "A,B,C" is for Power On Clear initialization of memory protect. With this selection you may choose for the memory protect feature of this board to be initialized in either the "Protect" or "Unprotect" mode of operation. f no standby voltage is used to retain memory data when the power is down then "Unprotect" (B to C) is the best choice. This will allow immediate use of the memory when power is first applied. f however you choose to use the Standby Data Retention feature the "Protect" mode (B to A) is best. This will automatically put the memory in write protect when power is applied so that the processor may not erase memory before you have programmed it. After power is up you may then reset it to unprotect and use it as you desire. Make the jumper selection for the mode you want to use. STANDBY VOLTAGE The standby voltage is used to retain memory data while the rest of the system is off. The voltage can be generated for your system by the use of two N-CAD batteries. This voltage may be applied to the unit on the S-OO buss Pins 13 and 14. The positive voltage should be applied to the pin marked "Standby" or Pins 13 and 14. The negative return should then be connected to Ground.
3 2 f Pins 13 and 14 are used for some other purpose in your system, you may select to cut the trace on the PCB in order to disconect them. WAT STATE SELECTON f you have 450 ns or faster memory C's and are using an 8080 CPU, will need zero wait states. f you then go to a faster CPU you may want to include 1,2 or 3 wait states. you Alternately, if you used a slower memory C you may need to allow for this by selecting enough wait states to achieve faultless operation of the memory.
4 8K REV. A PARTS L8T: 4 Heat Sinks U-U Voltage Regulator (A.K.A. 340 T-5) U5 8 position Dip 8witch U6,U7 74L885 U8 74L8138 U9 74L874 UlO 74L N4006 Ull 74L832 5 N4148 Ul2 74L802 U13-U16 74L804 U U18,Ul9 74L8368 U20-U Type Memory (not numbered on silk screen) RP 4. 7K 8P '; Rl, R2 2.4K 1/4 watt R3 4. 7K R4 470 R5 560 C10,C uf C9 47 uf Cl-8 and all the rest are 0.1 uf
5 DESRED MEMORY ADDRESS RANGE ADDRESS SWTCH POSTON K DECMAL HEX SPLT OCTAL A B C D E 1" G H "1"1" C C C C 0 C C C "1"1" C C C C 0 C C "1"1" C 0 C C 0 0 C C 1)-20 J "FF '7 0 0 C C C C 0 C C-5FFF C C 0 C 0 C 0 C FFF C 0 C C 0 0 C FFF C 0 0 C C e "1"1" C C C C FFF C C C 0 0 C C e AFF'F' C C 0 C 0 C AOOO-BFFF' C 0 C C BOOO-CFFF! C 0 C C COOO-DFFF C J '" C DOOO-EFFf' C 0 0 C EOOO-1"FFF C NOMENCLATURE: C = Closed o = Open (On) (Off) Address line Low Address line High n order to address your board, first determine the address space desired. set the select switches from the ADDRESS SWTCH POSTON Table. Then FORREST DUSTON
6 la-lllo USER'S CRTQUE To make this manual more useful to you, our customer, we will appreciate your comments and recommendations on any improvements to this r:.ljlual you feel are needed. After using this manual, please take the tint opportunity to complete this questionnaire and return it, postpaid, to the factory where your comments will be given every consideration. Thank you. MANUALORGANATON Was the Table ofcontents detailed enough and useful? DYes, 0 No, 0 Comment Were the manual sections well organized? DYes, 0 No, 0 Comment GRAPHCS How would you rate the quality of the photos, diagrams. etc.? o Excellent, 0 Adequate, 0 Poor Were there enough illustrations throughout the manual DYes, 0 No, 0 Comment Were the tables clear and easy to follow? DYes, 0 No, 0 Comment TEXT How would you rate the quality of the technical writing? o Excellent, 0 Adequate, 0 Poor f there are particular paragraphs, instructions, etc., you feel need clarification or rewriting, please identify them and add your comments. GENERAL COMMENTS Respondent Company Address City!State/Zip Title NO POSTAGE NECESSARY F MALED N U.S.A. Fold on the two lines on reverse side. staple or tape, and mail
7 FOLD HERE FRST CLASS Permit No. 892 THACA. N.Y. Business Reply Mail No postage necessary if mailed in the United States Postage wi" be paid by: THACA AUDO P.O. Box 91 thaca, New York FOLD HERE
8 LAY-OU-:.' DSGN 0 ti U U > >. 10> u 'i ) SWTC.H () Z02. > O> 10>. 1/-.7C.no SP URP 0> > 10> ) 0 l) f) u 11 0> > 10> ) 0 ) O> u 11 l(\ ClO :t' 7805 m= 0 OiS 0> ) Q) ) 10) ) 10) n 11 a U2 t\. ad. 0> > 10> ), lo> ) (» >!c 0> ) 10> > O> ). 10> > l 0 OS UJ 0 r 0> ) 10> > 10) > 10> ) ) > 10) ) O> ) 10> ) l 0 OD! U4 ti 5 0> 7'1 50 '/-. 1) 7'fLS0'1 0> 7'1LSoif 1) 7'1-/7'1- >1#-1.57/f,) 71f1.H lo> 7'1-.S 118 1) )'8 +ct U14 Ul5 U un 1ft 19 U G U U, G G 15 C> THACA AUDO > '."0>- ij>,.<so. 8K STATC MEMORY.AT A-ll10 REVSON A ti ti 1 UlD U D OOOOQbt o.
9 Ct! 51 'V 13 STBY 14 ADDRESS LNES TO l EORY ARRAY PN NO J AO n S 14 f!l., A 10 fl2-4 A2, 81 f!- 5 " > A3 5 f!- i A ri A5 rl- 2 PAn OA A A lla D' DC C CR.. CRll O.M' 11- T T T 011" -::- -:!:- " A 12 fl.+ S. A., 13 fe A' (> 15 ::. 14 f-l- 14,., < A2 AO 51 ; A 53.6 lz 411 S A A4 A soot 1.- n N', 12 - > f= =1 36 ; 0011 a!l 001 is !2- DATA NTO >- :::fy RY PN 3 D04 >.L. at D05.! D06 5 f!.- lo. D07, f!.- J R4,.,. ----/ V P. 5V ;: ::"l RP "--lv C4 h 4 PAH'A' >-- 11 ;J. T T T 0.111" 0:;:- SELECT C 4 SWTCtlU 11.J. 4111'T T T T -:!:-., E. PAlE 'C' SELECT SWTCHES 13 / D DATA' 'ROl EORY WAT STATES ARRAY ' 112 ' (2 y3 r:--<' PN ":" - A PROTECT r---ob c UNPROTECT Q 5 10 R (5V 2.4K 1 4.,0'" PROT 6 4 ',.!.",471\0\n,---;::-:-'r-""'.Ej C.L tal 20 UHlR, 5 12 '"-4.V WRT " f>- 2 J;.>" +5V Cl5 1 - R3 ls 4.7K!loe 1.4K 0. 00Ị. 10 " ":".11 C, Q -l3110 CO".L o.ool. "!l 121 lco,l.:.-. EORY ARRAY PN 3 POC l!jo'., PDBN , SEYA 10 PSYNC 5 7 >., SGND 1O ONP 1 -Jz.o *. '- Q ll' C : ': i : f : 17 ll' N.C.,,, T' 11 T T " 11/.- 14" : '" PlOV- 1'1 2r / A OU/ 1: 'Ot.l 012/ Dill / 42 j;;.r 7 014/ 4" A t D!l '2., , 017 ;' 43 SCAU,.- a,1ht """ A' "ALLEN '''1:.'t/7' THACA AUDO CH C< O WLLAS 1 0. TERAL. po. BOX 91 CT 'ore "ON' L :'l S UNLESS OTHERWSE NOTED THACA, NEW YORK,tc 'TATC ta 14B!50 DAT 1-aR AAOl' """" 'N"'" "'T A- 1110
Chill Interface PCB Assembly Instructions
ExcelValley Chill Interface PCB Waveblaster Module MIDI Interface Board Chill Limited Edition V2 Assembly Kit Standalone midi interface board for Waveblaster synthesizer modules. Suitable for most Waveblaster
More information*on-board power supply capability limited. External battery should be used for higher power servos.
Pan and Tilt Decoder II PART NO. Add affordable Pan and Tilt control to your security cameras using the Pan and Tilt Decoder II and the DFRobot DF05BB Tilt/Pan Kit (5kg), Jameco PN 2144518 or the DAGU
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationDIGITAL RESEARCH COMPUTERS
28K S-00 STATIC RAM/EPROM BOARD DIGITAL RESEARCH COMPUTERS (24) 225-2309 INTRODUCTION The 28K S-00 Static Ram/Eprom Board you have just purchased is one of the best Ram/Eprom bargains on the market today.
More informationGLiPIC Ver C Assembly manual Ver 1.0
GLiPIC Ver C Assembly manual Ver 1.0 Last Rev 1.1 Oct 30, 2001 Author: Ranjit Diol Disclaimer and Terms of Agreement As with any kit, only the individual parts supplied are guaranteed against defects and
More informationUF-3701 Power Board Construction Guide
Page 1/5 Soldering and Part Placement See the Chapter 3 of the MIT 6270 Manual for information on electronic assembly, including soldering techniques and component mounting. Construction Information All
More information4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..
IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationShack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3
1. Introduction Shack Clock kit PCB Revision: QCU Rev 1 or QCU Rev 3 Thank you for purchasing this QRP Labs Shack Clock kit. The kit uses the same PCB and bag of components as some other QRP Labs kits.
More informationThe Basic Counter. Hobby Electronics Soldering Kit. Instruction Guide
The Basic Counter Hobby Electronics Soldering Kit Instruction Guide TM For the best outcome, follow each step in order. We recommend reading this guide entirely before you get started. Tools required:
More informationsolutions for teaching and learning
RKP18Motor Component List and Instructions PCB layout Constructed PCB Schematic Diagram RKP18Motor Project PCB Page 1 Description The RKP18Motor project PCB has been designed to use PIC microcontrollers
More informationAssembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement.
NeoLoch NLT-28P-LCD-5S Assembly Instructions (8/14/2014) Your kit should contain the following items. If you find a part missing, please contact NeoLoch for a replacement. Kit contents: 1 Printed circuit
More informationMS11-E-J MOS memory user's manual
MS11-E-J MOS memory user's manual EK-MSIIE-OP-OOI / MS11-E-J MOSmemory user's manual '.1 digital equipment corporation maynard, massachusetts lst Edition, October 1976 Copyright 1976 by Digital Equipment
More informationAPC-H31/H32 Memory Expansion
Advanced Personal Computer APC-H31/H32 Memory Expansion Unit nstallation Guide NEe NEe nformation Systems, nc. 819-000104-9001 Rev.Ol 4-84 LMTED WARRANTY AND LABLTY DSCLAMER NEC nformation Systems, nc.
More informationES-562/564U COMBINATION CLOCK/TIMER
142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com ES-562/564U COMBINATION CLOCK/TIMER OPERATION AND MAINTENANCE MANUAL The ES-562U/564U is a combination six digit
More informationUniversity of Florida EEL 4744 Drs. Eric M. Schwartz, Karl Gugel & Tao Li Department of Electrical and Computer Engineering
Page 1/9 Revision 1 OBJECTIVES In this document you will learn how to solder and to debug a board as you are building it. REQUIRED MATERIALS Website documents o UF 68HC12 Development Board Manual (board
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationEDL-0A 2.5V CW LASER DIODE DRIVER
2.5V CW LASER DIODE DRIVER FEATURES z CW operation up to 60mA from 2.5..6V supply voltage z Rapid soft start after power-on z Simple power adjustment via the external resistor z Control loop accuracy better
More informationAVR-M Rev 5 ASSEMBLY
AVR-M Rev 5 ASSEMBLY The AVR_M is a very compact self contained Atmel AVR mcu controller board. It includes an onboard serial programmer (via PC com port), an I2C eeprom and can use a Mega163, Mega16 or
More informationCPU-2 Z80 CPU BOARD .. POWER ON JUMP TO ANY 256TH BIT. DIP SWITCH SELECTABLE HARDWARE GENERATION .. MAJOR EMPHASIS ON PROPER TIMJN~
CPU- Z80 CPU BOARD FEATURES: Z80 PROCESSOR ON BOARD ROM POWER ON JUMP TO ANY 56TH BIT. DIP SWITCH SELECTABLE HARDWARE GENERATION MAJOR EMPHASIS ON PROPER TIMJN WILL.lORK ON EXTENDER AT 4MHZ S\,ITCH SELECTABLE
More informationEK27. Evaluation Kit APPLICABLE PARTS (SOLD SEPARATELY) INTRODUCTION PA50 PA52
APPLICABLE PARTS (SOLD SEPARATELY) PA50 PA52 INTRODUCTION Evaluation Kit This easy to use kit provides a platform with good circuit board layout and grounding to evaluate linear power amplifier circuits
More informationDS2223/DS2224. EconoRAM FEATURES PACKAGE OUTLINE. PIN CONNECTIONS Pin 1 GND Ground Pin 2 DQ Data In/Out Pin 3 V CC Supply Pin 4 GND Ground
DS2223/DS2224 EconoRAM FEATURES Low cost, general purpose, 256 bit memory DS2223 has 256 bit SRAM DS2224 has 32 bit ROM, 224 bit SRAM Reduces control, address and data interface to a single pin PACKAGE
More informationInstruction Manual for BE-SP3 Circuit. 10/21/07
Page 1 of 54 Instruction Manual for BE-SP3 Circuit. 10/21/07 Page 1 Index: Page 2 BE-SP3 Circuit Specifications. Page 3-4 Intro to the BE-SP3. Page 5 Basics of serial to parallel. Page 6-7 ASCII Code.
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More information1 Description. 2 Specifications. Product Installation Document. Honeywell 12 Clintonville Road Northford, CT
Honeywell 12 Clintonville Road Northford, CT 06472 http://www.honeywellpower.com HP600ULACM4CB HP600ULACM8CB Access Control Power Supply/Charger with Power Distribution Controller PN 52395:A 1/05/06 ECN
More informationShack Clock kit. U3S Rev 2 PCB 1. Introduction
Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used
More informationSLCD1-IC Serial LCD Processor
SLCD1-IC Serial LCD Processor Diagram 1: LCD Pin 13 LCD Pin 14 1 2 18 17 LCD Pin 12 LCD Pin 11 N/C 3 16 8 MHz Osc DC 4 15 8 MHz Osc Ground 5 14 DC Serial Input True/Inverted 6 7 13 12 LCD Pin 6 LCD Pin
More informationZ-80 INSTRUCTION MANUAL. ~ Ithaca Audio Rights Reserved
Z-80 INSTRUCTION MANUAL ~ Ithaca Audio 1977 All Rights Reserved Circuit Features On board 2708 EPROM addressable to any 4K boundary above 32K -- Power-on-jump to any 4K boundary above 32K, or the on-board
More informationKPIC-0818P (V050919) Devices Included in this Data sheet: KPIC-0818P
Devices Included in this Data sheet: KPIC-0818P Features: Carefully designed prototyping area Accepts 8 pin PIC12 series micro-controllers Accepts 14 and 18 Pin PIC16 series Accepts some 8,14 and 18 pin
More informationDS1305. Serial Alarm Real Time Clock (RTC) FEATURES PIN ASSIGNMENT ORDERING INFORMATION
DS135 Serial Alarm Real Time Clock (RTC) FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 21 96 byte
More informationN8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B.
N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B. Background. This board is a copy of Andrew Lynch s Version 03 board (with 8 slots) but with added features. Added features: 9 SLOT Active Termination (copied
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationDS1306. Serial Alarm Real Time Clock (RTC)
www.dalsemi.com FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100 96-byte nonvolatile RAM for data
More informationDwarf Boards. DB057 : 40-pin controller board
Dwarf Boards DB057 : 40-pin controller board PICmicro, In-Circuit Serial Programming and ICSP are registered trademarks of Microchip Technology Inc. DB057 for USB PIC DB057 for non-usb PIC Introduction
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationORDERING INFORMATION Standard Products
ORDERING INFORMATION Standard Products AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the following: Am29LV640D
More informationVFO/Signal Generator kit PCB Revision QCU Rev 1 or QCU Rev 3
1. Introduction VFO/Signal Generator kit PCB Revision QCU Rev 1 or QCU Rev 3 Thank you for purchasing this QRP Labs kit. The QRP Labs kit range is modular. The kit uses the same PCB and bag of components
More informationDS1302. Trickle Charge Timekeeping Chip FEATURES PIN ASSIGNMENT PIN DESCRIPTION
DS132 Trickle Charge Timekeeping Chip FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 21 31 x 8 RAM
More informationµrrc µr/c Robot Controller v1.1
v1.1 OVERVIEW The µrrc is a simple, easy to use interface between a 3-channel R/C receiver and the OSMC H-Bridge controller for battle style robots. In principle, the µrrc can be used to drive any motor
More informationStorage Card Interface Kit
Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3K The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve
More informationQUASAR KIT No DIGITAL DOWN TIMER 99 MIN WITH PIC
QUASAR KIT No 1173 - DIGITAL DOWN TIMER 99 MIN WITH PIC KIT 1173 is a digital countdown timer based on a micro controller, thus securing reliability and excellent operation under any circumstances. It
More informationFlight Data Recorder Hardware Version 1.0
Flight Data Recorder Hardware Version 1.0 By R. G. Sparber Scope The Flight Data Recorder (FDR) hardware is described here. The software is described in a separate document. The reader can etch their own
More informationStorage Card Interface Kit
Storage Card Interface Kit for MultiMediaCards(MMC) and Secure Digital Cards (SD) MMSD3F The MMSD3K is complete development kit interfaced to a SD or MMC card. This board ideal for projects that involve
More informationES-362U PRESETTABLE MASTER TIMER
142 SIERRA ST., EL SEGUNDO, CA 90245 USA (310)322-2136 FAX (310)322-8127 www.ese-web.com ES-362U PRESETTABLE MASTER TIMER OPERATION AND MAINTENANCE MANUAL The ES-362U is a four digit, presettable 100 minute
More informationDS1305 Serial Alarm Real Time Clock (RTC)
Serial Alarm Real Time Clock (RTC) www.dalsemi.com FEATURES Real time clock counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap year compensation valid up to 2100
More informationRC Tractor Guy Controller V2.1 Assembly Guide
RC Tractor Guy Controller V. Assembly Guide Features 0 Push button inputs Dual axis thumb sticks with built-in push button Rotary encoders with built-in push button MCU Socket to suit Meduino Mega 560
More informationUniversal Keying Adapter 3+
Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port
More informationPAS 9737/AI-SMT ENGINEERING SPECIFICATION
Document PAS54 Spec Revision C (7/3/8) PAS 9737/AI-SMT ENGINEERING SPECIFICATION 64 CHANNEL, 6 BIT VME ANALOG INPUT CARD PCB Revision D (7/3/8) Additional copies of this manual or other Precision Analog
More information64-megabit (4M x 16) 3-volt Only Flash Memory AT49BV642D AT49BV642DT
BDTIC www.bdtic.com/atmel Features Single Voltage Operation Read/Write: 2.65V - 3.6V 2.7V - 3.6V Read/Write Access Time 70 ns Sector Erase Architecture One Hundred Twenty-seven 32K Word Main Sectors with
More informationTrigger I/O Board for the LogiComm Gun Driver
Instruction Sheet Trigger I/O Board for the LogiComm Gun Driver P/N 1084488A WARNING: This trigger I/O board is not directly compatible with the previous versions (P/N s 1069804 and 1069805). Refer to
More informationConstruction Manual for the W0EB/N5IB New ubitx Raduino Clone
Construction Manual for the W0EB/N5IB New ubitx Raduino Clone Version 1.5, January 09, 2019 Manual and Images Copyright W0EB and N5IB August 03. 2018, all rights reserved. May be freely reproduced and
More informationATLD10A5-D EV1.0 Evaluation Board for ATLD10A5-D 10A High Efficiency Laser Controller ATLD10A5-D Evaluation Board Rev. 1.0
ATLD0A5-D EV.0 Evaluation Board for ATLD0A5-D 0A High Efficiency Laser Controller ATLD0A5-D Evaluation Board Rev..0 Figure ATLD0A5-D EV.0 Photo INTORDUCTION The ATLD0A5-D is an electronic module designed
More informationPart 2: Building the Controller Board
v3.01, June 2018 1 Part 2: Building the Controller Board Congratulations for making it this far! The controller board uses smaller components than the wing boards, which believe it or not, means that everything
More informationMAX186 Evaluation System/Evaluation Kit
-0; Rev. ; /0 MAX Evaluation System/Evaluation Kit General Description The MAX evaluation system (EV system) consists of a MAX evaluation kit (EV kit) connected to a Maxim 0C microcontroller (µc) module.
More informationH8-USB CONTROLLER. Norberto Collado 5/5/2013
2013 H8-USB CONTROLLER Norberto Collado norby@koyado.com 5/5/2013 Revision History and Disclaimer Revision Date Comments Revision History 1.0 05/05/2013 Initial draft by Norberto Collado The purpose of
More informationKDS Channel DMX Controlled Servo Kit
KDS00801 8-Channel DMX Controlled Servo Kit This is a DMX512-A controlled servo kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 8-20 VDC @ 50 ma. The board features an
More informationLED Knight Rider. Yanbu College of Applied Technology. Project Description
LED Knight Rider Yanbu College of Applied Technology Project Description This simple circuit functions as a 12 LED chaser. A single illuminated LED 'walks' left and right in a repeating sequence, similar
More informationRapid40iXL PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
More informationHow Nohau supports the Philips 8051MX Microcontroller
How Nohau supports the Philips 8051MX Microcontroller There are two options for the emulation of the 8xC51MB2 and 8xC51MC2 micros. One is the emulator with 768k of emulation memory that has been configured
More informationRC-210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net RC-210 Repeater Controller Assembly Manual Hardware Version 3.0 Original Release Date September 13, 2004
More informationIC-I AND IC-I F GENERAL DESCRIPTION SPECIFICATIONS. Output Impedance: Phones: 60 ohms (Unit is designed for use with ohm phones.
IC-I AND IC-I F GENERAL DESCRIPTION The IC-1 and IC-1 F are single-channel, singleline intercom stations designed for use with dynamic headsets. The IC-1 is a compact, lightweight unit which may be worn
More informationAssembly of the TACOS WAT-910BD Housing v2
1) Circuit Diagram 2) Assembly of PCB a)tools Required. Only simple hand tools are necessary to complete the assembly of the PCB. - Soldering Iron and solder - Needle nose pliers - Wire clippers/trimmers
More informationArrakis Systems 6604 Powell Street / Loveland, Colorado 80538
Arrakis Systems 6604 Powell Street / Loveland, Colorado 80538 Input and Output wiring for the 150sc, 500sc, 2000sc and 2100sc audio consoles. A Input Channel Wiring (Back of Console) 6. Left Input 5. Left
More informationLCD Prototype Circuit on Solderless Breadboard. 840 Pin Solderless Breadboard (http://www.digikey.com/ # ND)
Solderless Breadboard Tutorial Cornerstone Electronics Technology and Robotics I Week 3 Solderless Breadboards: o Solderless breadboards are commonly used in experimentation or to make a prototype of a
More informationMRUC-20 Modul-R CAN Bus Network
MRUC-20 Modul-R CAN Bus Network BALOGH This manual is based on information available at the time if its publication. Every effort has been made to provide accurate and up-to-date information. This document
More informationParts IV-11 DCF melody Date, Weekday, Temperature
Parts IV-11 DCF melody Date, Weekday, Temperature Parts PSU Parts Bag 1a Power Adapter 12 Volt F1 Bridge / NTC 10R black NTC only for Power Adapter 15 Volt R1 4,7M yellow, violet, green R2 1M brown, black,
More informationRapid40i PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
More information3-Card Slot, Includes P1/P2/P3/P4 compatibility for Analog I/O, Digital I/O, & Pulse/Frequency
DBK213 Screw-Terminal & Expansion Card Module 3-Card Slot, Includes P1/P2/P3/P4 compatibility for Analog I/O, Digital I/O, & Pulse/Frequency Overview 1 Connection Tips 2 Installing DBK Cards 3 System Examples
More informationEvaluation Board LX1752 EVALUATION BOARD USER GUIDE
LX1752 Dual Interleaving PWM Controller Evaluation Board TM Page 1 CONTENTS INTRODUCTION TO PRODUCT... 3 FEATURES:... 3 OPERATION... 3 TEST POINTS... 4 INPUT AND OUTPUT CONNECTION POINTS... 4 LX1752 EVALUATION
More informationBMC24. MIDI TO GATE CONVERTER DOCUMENTATION. This documentation is for use with the "Euro Style" bottom board.
BMC24. MIDI TO GATE CONVERTER DOCUMENTATION. This documentation is for use with the "Euro Style" bottom board. A. USING THE MIDI TO GATE CONVERTER B. PARTS LIST C. BUILDING INSTRUCTIONS D. SCHEMATICS Revision.
More informationH89-Z37 DOUBLE-DENSITY FLOPPY CONTROLLER
H8-Z37 DOUBLE DENSITY FLOPPY CONTROLLER 2015 H89-Z37 DOUBLE-DENSITY FLOPPY CONTROLLER Norberto Collado norby@koyado.com 6/6/2015 Revision History and Disclaimer Revision History Revision Date Comments
More informationDS1305EN. Serial Alarm Real-Time Clock
Serial Alarm Real-Time Clock www.maxim-ic.com FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap-year compensation valid up to
More informationKIT 134. INTRODUCTION TO LCD S
The aim of this kit is to show how to use a 16x2 alphanumeric Liquid Crystal Display (LCD) with a PC. First we show how to connect it to the parallel port and echo and handle keyboard input. Then we show
More informationW0EB/W2CTX DSP Audio Filter Construction Manual V3.02.1
W0EB/W2CTX DSP Audio Filter Construction Manual V3.02.1 Manual and photographscopyright W0EB/W2CTX, January 01, 2019. This document may be freely copied and distributed so long as no changes are made and
More informationElectronic Coin Toss
1 Electronic Coin Toss Why this circuit? This circuit was not designed for people who can make up their mind nor have a coin to use for a heads or tail coin toss. This circuit can also be used to ask it
More informationSERVICE MANUAL. Power Plant Premier APPLICABLE PRODUCTS. Serial numbers PPP-7J and earlier. Document # DSM-A Released 01/08
SERVICE MANUAL Power Plant Premier APPLICABLE PRODUCTS Serial numbers PPP-7J and earlier Document # 11-037-01-1-DSM-A Released 01/08 BASIC DISASSEMBLY PROCEDURE 1) Place the unit upside down on a well
More informationRapid28iXL PIC Prototyping PCB User Manual
Description Features This is a PCB designed to facilitate the rapid prototyping of a device based on a 28 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of
More informationDS1305EN. Serial Alarm Real-Time Clock
Serial Alarm Real-Time Clock www.maxim-ic.com FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with leap-year compensation valid up to
More informationQRPGuys Single Lever Keyer/Paddle
QRPGuys Single Lever Keyer/Paddle First, familiarize yourself with the parts and check for all the components. If a part is missing, please contact us and we will send one. You must use qrpguys.parts@gmail.com
More informationMODEL PUSHBUTTON DIAL
ITT Practices MODEL 188478 PUSHBUTTON DIAL SECTION 478 117 Issue 1, Oct. 1984 CONTENTS PAGE 1. INTRODUCTION... 1 2. GENERAL DESCRIPTION............ 1 MODEL 188478 103. MODEL 188478 101. 3 4 MODEL 188478
More informationAssembly Instructions for the KA Electronics Elliptic Equalizer
Assembly Instructions for the KA Electronics Elliptic Equalizer Install IC sockets Elliptic Equalizer PC Board Stuffing Guide Place the PC Board on the work bench silkscreen side face up. Place twelve
More informationRC210 Repeater Controller Assembly Manual
Arcom Communications 24035 NE Butteville Rd Aurora, Oregon 97002 (503) 678-6182 arcom@ah6le.net http://www.arcomcontrollers.com/ RC210 Repeater Controller Assembly Manual Hardware Version 3.3 Reproduction
More informationS-2812A/2817A. Rev.1.1. CMOS 16K-bit PARALLEL E 2 PROM
Rev.1.1 CMOS 16K-bit PARALLEL E 2 PROM The S-2812A and the S-2817A are low power 2K 8-bit parallel E 2 PROMs. The S-2812A features wide operating voltage range, and the S-2817A features 5-V single power
More informationSRD- Switching Regulator Step-down regulator. Switch-mode Step-down Regulator
Switch-mode Step-down The SRD power converter is a high frequency, switch-mode, step-down regulator for applications requiring stable power. The compact and efficient design requires little heatsinking
More informationRetro Elf Plus - CPU 64K Board - Revision F
Retro Elf Plus - CPU 64K Board - Revision F Copyright 2016, by D.T.Runkle Website at www.astrorat.com Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free
More informationElectronics Assembly and Test Plan Rev 3
Overview This test plan will describe the process for testing and assembling the electronics system. It will discuss the required equipment, applicable engineering requirements, desired outcomes of each
More informationButterfly Laser Diode Mount
LM14S2 Butterfly Laser Diode Mount Operating Manual LM14S2 Laser On TEC Driver LD Driver THORLABS, Inc. Ph: (973) 579-7227 435 Route 206N Fax: (973) 383-8406 Newton, NJ 07860 USA www.thorlabs.com 10614-D02
More informationSemi-Virtual Disk III
Semi-Virtual Disk III Revision B Manual Version 0.02 1 of 21 April 14, 2017 1 - Introduction The original idea behind the Semi-Virtual Disk (SVD) was invented by Eric Rothfus back in 2003. As Eric stated
More informationSierra Radio Systems. HamStack. Project Board Reference Manual V1.0
Sierra Radio Systems HamStack Project Board Reference Manual V1.0 Welcome HamStack Project Board Reference Manual Revision 1.0.3 2011 George Zafiropoulos, KJ6VU and John Best, KJ6K This guide provides
More informationComputer Specifications
power (speed) light hard disk access light power - button Controllers Video Diskette Hard disk nterfaces External VESA local bus video cam supports high resolution displays (preinstailed on systems sold
More informationBUILDING YOUR KIT. For the Toadstool Mega328.
BUILDING YOUR KIT For the Toadstool Mega328 www.crash-bang.com @crashbang_proto This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. Congratulations! You re
More informationBS2p40tm OEM Module. Surface mount/through hole kit By Robert L. Doerr. Manual Revision.5
BS2p40tm OEM Module Surface mount/through hole kit 2006 By Robert L. Doerr Manual Revision.5 NOTE: The BASIC Stamp and the BS2p40 and Interpreter chip are trademarks of Parallax. This partial kit allows
More informationSM010, Assembly Manual PCB Version 1.0
180 SM010, Assembly Manual MATRIXARCHATE 16 8 IO SEQUENTIAL MATRIX SIGNAL ROUTER SM010 1 2 1 2 3 4 5 3 4 5 6 7 8 9 10 11 12 6 7 8 9 10 11 12 13 14 15 16 PROGRAM A B C D E F G H f1 f2 20.000 180 SSSR Labs
More informationAdvanced Strobe 1.0 Kit
Kit Instruction Manual Eastern Voltage Research, LLC December 2013, Rev 1 1 http://www.easternvoltageresearch.com Kit Introduction to the Kit Thank you for purchasing the Kit. If you are looking for a
More informationCopyright 2008, 2009 Grandad s Electronics Seattle, Washington, USA. INSTRUCTION MANUAL Model XTAL1. XTAL1 (assembled)
Copyright 2008, 2009 Grandad s Electronics Seattle, Washington, USA INSTRUCTION MANUAL Model XTAL1 XTAL1 (assembled) 1 XTAL1 Manual, 12/23/2008 Assembly Instructions This kit assumes that the purchaser
More informationAUDIO AMPLIFIER PROJECT
Intro to Electronics 110 - Audio Amplifier Project AUDIO AMPLIFIER PROJECT In this project, you will learn how to master a device by studying all the parts and building it with a partner. Our test subject:
More informationTIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE
TIME WIZARD MULTI CLOCK DIVIDER BUILDING GUIDE Table of Contents 0. Components List + Tools 0. PCB Sides 03. PCB Assembly 04_. Diode N448 04_. Laying Resistors 04_3. Capacitors 04_4. Quartz 04_5. 78L05
More informationPicoTurbine Mark 8.3 Generator Field Controller Kit
PicoTurbine Mark 8.3 Generator Field Controller Kit Based on a design published in Home Power magazine by Richard Perez. Used with permission. Reprint of original article included with kit. An easy-to-build
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: June 20,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: June 20, 2017 ea3gcy@gmail.com Updates and news at: www.ea3gcy.com Thanks for constructing the TKEY-1A CW touch key Have
More informationKDR00101 DMX Controlled Relay Kit
KDR00101 DMX Controlled Relay Kit This is a DMX512-A relay kit using ANSI approved RJ-45 connectors for DMX networks. Power requirements are 12 Vdc @ 100 ma. The relay contact rating is 10 Amp @ 120 or
More information