Lecture-55 System Interface:

Size: px

Start display at page:

Download "Lecture-55 System Interface:"

Erick Wright
5 years ago
Views:

1 Lecture-55 System Interface: To interface 8253 with 8085A processor, CS signal is to be generated. Whenever CS =0, chip is selected and depending upon A 1 and A 0 one of the internal registers is selected for data transfer. Let the chip be interfaced using isolated I/O. Since in isolated I/O mapped interfacing, IN PORT & OUT PORT instructions are used, therefore 8-bit port address is duplicated as explained earlier. A 15 - A 8 = A 7 - A 0 Since A 1 and A 0 select the internal register, these bits are not used to generate CS. Let us consider the remaining bits A 15 A 11 be and A 10 is not used to simplify the decoding circuit. Therefore, chip will be selected whenever higher address A 15 A 8 be 00010xxx. The two bits A 1 (or A 9 ) and A 0 (or A 8 ) select one of the timer or the control word register. Accordingly, the addresses for timer/counters and control word register would be as below: Primary Address Fold Back Address Timer/Counter = 10H = 14H Timer/Counter = 11H = 15H Timer/Counter = 12H = 16H Control Word Register = 13H = 17H Using these addresses, interfacing circuit can be developed. The interfacing circuit for 8253 is shown below:

2 IO/M A15 A14 A13 A12 A11 A1 A0 AD7-AD0 RD WR 8 CS RD WR A1 A0 D7-D Timer 0 Timer 1 Timer 2 CLK0 GATE0 OUT0 CLK1 GATE1 OUT1 CLK2 GATE2 OUT2 Fig.10.4 Interfacing of 8253 with Microprocessor The other possible circuit may have IO/M combined with RD and WR to generate IO/M and IO/W and these signals are then connected to RD and WR. In this case IO/M need not be used for generating CS. Initialization: Each of the three timers of 8253, TM 0, TM 1 and TM 2 can be independently programmed to operate in six different modes of operation. To initialize the timers, microprocessor writes a command word to control word register to select the operational parameters for the counter, that is, to specify which of the six modes is to be used, to select either binary or BCD decrementing and a code to specify whether 8-bit or 16-bit value is to loaded or latch the counter. One control word is required for each timer and they can be programmed in any sequence; need not be in a sequence TM 0, TM 1 and TM 2. When the power is first turned ON, the timers are in undefined states.

3 The control word format is shown below: D 7 D 6 D 5 D 4 D 3 D 2 D 1 D 0 SC1 SC0 RL1 RL0 M2 M1 M0 BCD SC1 & SC0: These bits indicate whether the control word being issued is intended for Timer/Counter 0, 1 or 2 as indicated in the table: SC1 SC0 0 0 Select counter Select counter Select counter Illegal, Not permitted RL1, RL0: Each of the 8253 s counters is 16-bit down counter. Since they are accessed via an 8-bit data bus, two separate read or write operations are required to completely read or write the count value from/to one counter. The 8253 allows the user to read or write either 8-bit or 16-bit data and thus allows a substantial degree of freedom in this regard. The next two bits RL1 and RL0 selects one of this operation as shown below: RL1 RL0 0 0 Counter latching operation 0 1 Read/ Load least significant byte only 1 0 Read/ Load most significant byte only 1 1 Read/ Load least significant byte first, then most significant byte.

4 If both RL1 and RL0 are 0, the four lower order bits (M 2, M 1, M 0 and BCD) are don t cares. In this case, the control word being issued is to latch the count value in the selected counter. M2, M1, M0: The mode of operation of the timer is selected by these three bits as per table below:. M 2 M 1 M 0 Mode Mode Mode 1 X 1 0 Mode 2 X 1 1 Mode Mode Mode 5 BCD: A 0 in this bit position programs the selected counter to operate as a 16-bit binary counter. The maximum value in binary is FFFFH. A 1 in this bit programs the selected counter to operate as a 4-digit BCD counter. The maximum value in BCD is 9999D. The 16- bit counters are down counters. This means that number in a counter will be decrement by each clock pulse. The zero count is checked after the counter is decremented. Therefore, the maximum count value in both cases will be 0000; after first decrement the count becomes either FFFFH or 9999D depending on BCD bit. After the control word register has been programmed, the 8253 expects the count to be located into the counter as specified by the

5 RL bits of control word. If more than one counter is to be programmed at one time, the software may be written to write a control word to each counter and then load the count into each and counter or each counter may be programmed completely with a control word and the count value before initializing the other counter. Modes of Operation: Each of the three counters of 8253 can be programmed to operate in six different modes of operation to produce the desired output. Each timer requires a clock input. The counters are negative edge triggered down counter, i.e., whenever there is HIGH to LOW transition at the CLK input, the count value is decremented by 1. The down counting is controlled by the gate. The output pin of the timer may be used to generate different signals, e.g., an interrupt request signal in the interrupt related modes. Counter Loading: In general, the counter register (or counting element) is not loaded from input register (or input element) until the value written is followed by a rising edge and a following edge of the clock input to the counter as shown in figure below. In some of the modes, the following edge of the clock input transfers the count value from input element to counting element.

6 CLK WR N= Fig.10.5 Counter Loading Mode-0: Interrupt on Terminal Count The output of the timer/counter goes low whenever a timer is programmed in mode 0. This is the only mode in which the normal output of the timer is low. In rest of the modes, the normal output of the timer is high. After the count value is loaded into the timer, the output of the counter will remain low. If the gate is low the counting is disabled. Once the gate is made HIGH, the 16-bit count value is transferred from input element to counting element after one rising and falling edge of the clock signal. The counter starts down counting on subsequent clock pulses. The output remains low until count value reaches 0. When the count value becomes zero, we say terminal count has reached. The output will go high and remains high. This LOW to HIGH transition at the output pin may be used to interrupt the processor and to tell the processor that the desired delay is over. The processor can take necessary action at this moment by transferring control to an interrupt service subroutine. The output will not be changed until the selected counter is reloaded with the mode word or a new count value is loaded. After the counter has reached zero it will continue to count down internally from 0000H to FFFFH to FFFEH and so on but will not change the output signal.

7 If the GATE is made 0 in this mode, the counter is disabled. However, the count stops counting if GATE goes low during counting and the current count value is freezed. Counting resumes from the frozen value, when GATE is made high again. The count is decrement at every HIGH to LOW transition till it becomes zero. Therefore, the counter basically counts N clock pulses or N+1 transition of the clock. CLK WR N=4 4 GATE OUT T.C. GATE OUT Fig.10.6 Timing Waveforms of Timer in Mode-0 0 T.C. The count value may be changed at any instant even when the counting operation is going on. Loading a new count value essentially restart the counter with this new value. Note that if the counter value

8 to be loaded is of 8-bits, the effect of loading the new count value is immediate, i.e., as soon as the new count value is loaded into input element, it will be transferred to counting element and counting begins with new initial count value. If the count value to be loaded is of 16-bits, the counter stops counting after the first byte is loaded and resumes counting only after the second byte is loaded.

8254 is a programmable interval timer. Which is widely used in clock driven digital circuits. with out timer there will not be proper synchronization

8254 is a programmable interval timer. Which is widely used in clock driven digital circuits. with out timer there will not be proper synchronization between two devices. So it is very useful chip. The