Chapter 4. The Processor
|
|
|
- Oscar Watts
- 6 years ago
- Views:
Transcription
1 Chapter 4 The Processor
2 Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified version A more realistic pipelined version Simple subset, shows most aspects Memory reference: lw, sw Arithmetic/logical: add, sub, and, or, slt Control transfer: beq, j 4.1 Introduction Chapter 4 The Processor 2
3 Instruction Execution PC instruction memory, fetch instruction Register numbers register file, read registers Depending on instruction class Use ALU to calculate Arithmetic result Memory address for load/store Branch target address Access data memory for load/store PC target address or PC + 4 Chapter 4 The Processor 3
4 CPU Overview Chapter 4 The Processor 4
5 Multiplexers Can t just join wires together Use multiplexers Chapter 4 The Processor 5
6 Control Chapter 4 The Processor 6
7 Logic Design Basics Information encoded in binary Low voltage = 0, High voltage = 1 One wire per bit Multi-bit data encoded on multi-wire buses Combinational element Operate on data Output is a function of input State (sequential) elements Store information 4.2 Logic Design Conventions Chapter 4 The Processor 7
8 Combinational Elements AND-gate Y = A & B Adder Y = A + B A B + Y A B I0 I1 M u x S Y Multiplexer Y = S? I1 : I0 Y Arithmetic/Logic Unit Y = F(A, B) A ALU Y B F Chapter 4 The Processor 8
9 Sequential Elements Register: stores data in a circuit Uses a clock signal to determine when to update the stored value Edge-triggered: update when Clk changes from 0 to 1 D Clk Q Clk D Q Chapter 4 The Processor 9
10 Sequential Elements Register with write control Only updates on clock edge when write control input is 1 Used when stored value is required later Clk D Write Clk Q Write D Q Chapter 4 The Processor 10
11 Clocking Methodology Combinational logic transforms data during clock cycles Between clock edges Input from state elements, output to state element Longest delay determines clock period Chapter 4 The Processor 11
12 Building a Datapath Datapath Elements that process data and addresses in the CPU Registers, ALUs, mux s, memories, We will build a MIPS datapath incrementally Refining the overview design 4.3 Building a Datapath Chapter 4 The Processor 12
13 Instruction Fetch 32-bit register Increment by 4 for next instruction Chapter 4 The Processor 13
14 R-Format Instructions Read two register operands Perform arithmetic/logical operation Write register result Chapter 4 The Processor 14
15 Load/Store Instructions Read register operands Calculate address using 16-bit offset Use ALU, but sign-extend offset Load: Read memory and update register Store: Write register value to memory Chapter 4 The Processor 15
16 Branch Instructions Read register operands Compare operands Use ALU, subtract and check Zero output Calculate target address Sign-extend displacement Shift left 2 places (word displacement) Add to PC + 4 Already calculated by instruction fetch Chapter 4 The Processor 16
17 Branch Instructions Just re-routes wires Sign-bit wire replicated Chapter 4 The Processor 17
18 Composing the Elements First-cut data path does an instruction in one clock cycle Each datapath element can only do one function at a time Hence, we need separate instruction and data memories Use multiplexers where alternate data sources are used for different instructions Chapter 4 The Processor 18
19 R-Type/Load/Store Datapath Chapter 4 The Processor 19
20 Full Datapath Chapter 4 The Processor 20
21 ALU Control ALU used for Load/Store: F = add Branch: F = subtract R-type: F depends on funct field ALU control Function 0000 AND 0001 OR 0010 add 0110 subtract 0111 set-on-less-than 1100 NOR 4.4 A Simple Implementation Scheme Chapter 4 The Processor 21
22 ALU Control Assume 2-bit ALUOp derived from opcode Combinational logic derives ALU control opcode ALUOp Operation funct ALU function ALU control lw 00 load word XXXXXX add 0010 sw 00 store word XXXXXX add 0010 beq 01 branch equal XXXXXX subtract 0110 R-type 10 add add 0010 subtract subtract 0110 AND AND 0000 OR OR 0001 set-on-less-than set-on-less-than 0111 Chapter 4 The Processor 22
23 The Main Control Unit Control signals derived from instruction R-type Load/ Store Branch 0 rs rt rd shamt funct 31:26 25:21 20:16 15:11 10:6 5:0 35 or 43 rs rt address 31:26 25:21 20:16 15:0 4 rs rt address 31:26 25:21 20:16 15:0 opcode always read read, except for load write for R-type and load sign-extend and add Chapter 4 The Processor 23
24 Datapath With Control Chapter 4 The Processor 24
25 R-Type Instruction Chapter 4 The Processor 25
26 Load Instruction Chapter 4 The Processor 26
27 Branch-on-Equal Instruction Chapter 4 The Processor 27
28 Implementing Jumps Jump 2 address Jump uses word address Update PC with concatenation of Top 4 bits of old PC 26-bit jump address 00 31:26 25:0 Need an extra control signal decoded from opcode Chapter 4 The Processor 28
29 Datapath With Jumps Added Chapter 4 The Processor 29
30 Performance Issues Longest delay determines clock period Critical path: load instruction Instruction memory register file ALU data memory register file Not feasible to vary period for different instructions Violates design principle Making the common case fast We will improve performance by pipelining Chapter 4 The Processor 30
31 Pipelining Analogy Pipelined laundry: overlapping execution Parallelism improves performance Four loads: Speedup = 8/3.5 = 2.3 Non-stop: Speedup = 2n/0.5n = number of stages 4.5 An Overview of Pipelining Chapter 4 The Processor 31
32 MIPS Pipeline Five stages, one step per stage 1. IF: Instruction fetch from memory 2. ID: Instruction decode & register read 3. EX: Execute operation or calculate address 4. MEM: Access memory operand 5. WB: Write result back to register Chapter 4 The Processor 32
33 Pipeline Performance Assume time for stages is 100ps for register read or write 200ps for other stages Compare pipelined datapath with single-cycle datapath Instr Instr fetch Register read ALU op Memory access Register write Total time lw 200ps 100 ps 200ps 200ps 100 ps 800ps sw 200ps 100 ps 200ps 200ps 700ps R-format 200ps 100 ps 200ps 100 ps 600ps beq 200ps 100 ps 200ps 500ps Chapter 4 The Processor 33
34 Pipeline Performance Single-cycle (T c = 800ps) Pipelined (T c = 200ps) Chapter 4 The Processor 34
35 Pipeline Speedup If all stages are balanced i.e., all take the same time Time between instructions pipelined = Time between instructions nonpipelined Number of stages If not balanced, speedup is less Speedup due to increased throughput Latency (time for each instruction) does not decrease Chapter 4 The Processor 35
36 Pipelining and ISA Design MIPS ISA designed for pipelining All instructions are 32-bits Easier to fetch and decode in one cycle c.f. x86: 1- to 17-byte instructions Few and regular instruction formats Can decode and read registers in one step Load/store addressing Can calculate address in 3 rd stage, access memory in 4 th stage Alignment of memory operands Memory access takes only one cycle Chapter 4 The Processor 36
37 Hazards Situations that prevent starting the next instruction in the next cycle Structure hazards A required resource is busy Data hazard Need to wait for previous instruction to complete its data read/write Control hazard Deciding on control action depends on previous instruction Chapter 4 The Processor 37
38 Structure Hazards Conflict for use of a resource In MIPS pipeline with a single memory Load/store requires data access Instruction fetch would have to stall for that cycle Would cause a pipeline bubble Hence, pipelined datapaths require separate instruction/data memories Or separate instruction/data caches Chapter 4 The Processor 38
39 Data Hazards An instruction depends on completion of data access by a previous instruction add $s0, $t0, $t1 sub $t2, $s0, $t3 Chapter 4 The Processor 39
40 Forwarding (aka Bypassing) Use result when it is computed Don t wait for it to be stored in a register Requires extra connections in the datapath Chapter 4 The Processor 40
41 Load-Use Data Hazard Can t always avoid stalls by forwarding If value not computed when needed Can t forward backward in time! Chapter 4 The Processor 41
42 Code Scheduling to Avoid Stalls Reorder code to avoid use of load result in the next instruction C code for A = B + E; C = B + F; stall stall lw $t1, 0($t0) lw $t2, 4($t0) add $t3, $t1, $t2 sw $t3, 12($t0) lw $t4, 8($t0) add $t5, $t1, $t4 sw $t5, 16($t0) 13 cycles lw $t1, 0($t0) lw $t2, 4($t0) lw $t4, 8($t0) add $t3, $t1, $t2 sw $t3, 12($t0) add $t5, $t1, $t4 sw $t5, 16($t0) 11 cycles Chapter 4 The Processor 42
43 Control Hazards Branch determines flow of control Fetching next instruction depends on branch outcome Pipeline can t always fetch correct instruction Still working on ID stage of branch In MIPS pipeline Need to compare registers and compute target early in the pipeline Add hardware to do it in ID stage Chapter 4 The Processor 43
44 Stall on Branch Wait until branch outcome determined before fetching next instruction Chapter 4 The Processor 44
45 Branch Prediction Longer pipelines can t readily determine branch outcome early Stall penalty becomes unacceptable Predict outcome of branch Only stall if prediction is wrong In MIPS pipeline Can predict branches not taken Fetch instruction after branch, with no delay Chapter 4 The Processor 45
46 MIPS with Predict Not Taken Prediction correct Prediction incorrect Chapter 4 The Processor 46
47 More-Realistic Branch Prediction Static branch prediction Based on typical branch behavior Example: loop and if-statement branches Predict backward branches taken Predict forward branches not taken Dynamic branch prediction Hardware measures actual branch behavior e.g., record recent history of each branch Assume future behavior will continue the trend When wrong, stall while re-fetching, and update history Chapter 4 The Processor 47
48 Pipeline Summary The BIG Picture Pipelining improves performance by increasing instruction throughput Executes multiple instructions in parallel Each instruction has the same latency Subject to hazards Structure, data, control Instruction set design affects complexity of pipeline implementation Chapter 4 The Processor 48
49 MIPS Pipelined Datapath 4.6 Pipelined Datapath and Control MEM Right-to-left flow leads to hazards WB Chapter 4 The Processor 49
50 Pipeline registers Need registers between stages To hold information produced in previous cycle Chapter 4 The Processor 50
51 Pipeline Operation Cycle-by-cycle flow of instructions through the pipelined datapath Single-clock-cycle pipeline diagram Shows pipeline usage in a single cycle Highlight resources used c.f. multi-clock-cycle diagram Graph of operation over time We ll look at single-clock-cycle diagrams for load & store Chapter 4 The Processor 51
52 IF for Load, Store, Chapter 4 The Processor 52
53 ID for Load, Store, Chapter 4 The Processor 53
54 EX for Load Chapter 4 The Processor 54
55 MEM for Load Chapter 4 The Processor 55
56 WB for Load Wrong register number Chapter 4 The Processor 56
57 Corrected Datapath for Load Chapter 4 The Processor 57
58 EX for Store Chapter 4 The Processor 58
59 MEM for Store Chapter 4 The Processor 59
60 WB for Store Chapter 4 The Processor 60
61 Multi-Cycle Pipeline Diagram Form showing resource usage Chapter 4 The Processor 61
62 Multi-Cycle Pipeline Diagram Traditional form Chapter 4 The Processor 62
63 Single-Cycle Pipeline Diagram State of pipeline in a given cycle Chapter 4 The Processor 63
64 Pipelined Control (Simplified) Chapter 4 The Processor 64
65 Pipelined Control Control signals derived from instruction As in single-cycle implementation Chapter 4 The Processor 65
66 Pipelined Control Chapter 4 The Processor 66
67 Data Hazards in ALU Instructions Consider this sequence: sub $2, $1,$3 and $12,$2,$5 or $13,$6,$2 add $14,$2,$2 sw $15,100($2) We can resolve hazards with forwarding How do we detect when to forward? 4.7 Data Hazards: Forwarding vs. Stalling Chapter 4 The Processor 67
68 Dependencies & Forwarding Chapter 4 The Processor 68
69 Detecting the Need to Forward Pass register numbers along pipeline e.g., ID/EX.RegisterRs = register number for Rs sitting in ID/EX pipeline register ALU operand register numbers in EX stage are given by ID/EX.RegisterRs, ID/EX.RegisterRt Data hazards when 1a. EX/MEM.RegisterRd = ID/EX.RegisterRs 1b. EX/MEM.RegisterRd = ID/EX.RegisterRt 2a. MEM/WB.RegisterRd = ID/EX.RegisterRs 2b. MEM/WB.RegisterRd = ID/EX.RegisterRt Fwd from EX/MEM pipeline reg Fwd from MEM/WB pipeline reg Chapter 4 The Processor 69
70 Detecting the Need to Forward But only if forwarding instruction will write to a register! EX/MEM.RegWrite, MEM/WB.RegWrite And only if Rd for that instruction is not $zero EX/MEM.RegisterRd 0, MEM/WB.RegisterRd 0 Chapter 4 The Processor 70
71 Forwarding Paths Chapter 4 The Processor 71
72 Forwarding Conditions EX hazard if (EX/MEM.RegWrite and (EX/MEM.RegisterRd 0) and (EX/MEM.RegisterRd = ID/EX.RegisterRs)) ForwardA = 10 if (EX/MEM.RegWrite and (EX/MEM.RegisterRd 0) and (EX/MEM.RegisterRd = ID/EX.RegisterRt)) ForwardB = 10 MEM hazard if (MEM/WB.RegWrite and (MEM/WB.RegisterRd 0) and (MEM/WB.RegisterRd = ID/EX.RegisterRs)) ForwardA = 01 if (MEM/WB.RegWrite and (MEM/WB.RegisterRd 0) and (MEM/WB.RegisterRd = ID/EX.RegisterRt)) ForwardB = 01 Chapter 4 The Processor 72
73 Double Data Hazard Consider the sequence: add $1,$1,$2 add $1,$1,$3 add $1,$1,$4 Both hazards occur Want to use the most recent Revise MEM hazard condition Only fwd if EX hazard condition isn t true Chapter 4 The Processor 73
74 Revised Forwarding Condition MEM hazard if (MEM/WB.RegWrite and (MEM/WB.RegisterRd 0) and not (EX/MEM.RegWrite and (EX/MEM.RegisterRd 0) and (EX/MEM.RegisterRd = ID/EX.RegisterRs)) and (MEM/WB.RegisterRd = ID/EX.RegisterRs)) ForwardA = 01 if (MEM/WB.RegWrite and (MEM/WB.RegisterRd 0) and not (EX/MEM.RegWrite and (EX/MEM.RegisterRd 0) and (EX/MEM.RegisterRd = ID/EX.RegisterRt)) and (MEM/WB.RegisterRd = ID/EX.RegisterRt)) ForwardB = 01 Chapter 4 The Processor 74
75 Datapath with Forwarding Chapter 4 The Processor 75
76 Load-Use Data Hazard Need to stall for one cycle Chapter 4 The Processor 76
77 Load-Use Hazard Detection Check when using instruction is decoded in ID stage ALU operand register numbers in ID stage are given by IF/ID.RegisterRs, IF/ID.RegisterRt Load-use hazard when ID/EX.MemRead and ((ID/EX.RegisterRt = IF/ID.RegisterRs) or (ID/EX.RegisterRt = IF/ID.RegisterRt)) If detected, stall and insert bubble Chapter 4 The Processor 77
78 How to Stall the Pipeline Force control values in ID/EX register to 0 EX, MEM and WB do nop (no-operation) Prevent update of PC and IF/ID register Using instruction is decoded again Following instruction is fetched again 1-cycle stall allows MEM to read data for lw Can subsequently forward to EX stage Chapter 4 The Processor 78
79 Stall/Bubble in the Pipeline Stall inserted here Chapter 4 The Processor 79
80 Stall/Bubble in the Pipeline Or, more accurately Chapter 4 The Processor 80
81 Datapath with Hazard Detection Chapter 4 The Processor 81
82 Stalls and Performance The BIG Picture Stalls reduce performance But are required to get correct results Compiler can arrange code to avoid hazards and stalls Requires knowledge of the pipeline structure Chapter 4 The Processor 82
83 Branch Hazards If branch outcome determined in MEM 4.8 Control Hazards Flush these instructions (Set control values to 0) PC Chapter 4 The Processor 83
84 Reducing Branch Delay Move hardware to determine outcome to ID stage Target address adder Register comparator Example: branch taken 36: sub $10, $4, $8 40: beq $1, $3, 7 44: and $12, $2, $5 48: or $13, $2, $6 52: add $14, $4, $2 56: slt $15, $6, $ : lw $4, 50($7) Chapter 4 The Processor 84
85 Example: Branch Taken Chapter 4 The Processor 85
86 Example: Branch Taken Chapter 4 The Processor 86
87 Data Hazards for Branches If a comparison register is a destination of 2 nd or 3 rd preceding ALU instruction add $1, $2, $3 IF ID EX MEM WB add $4, $5, $6 IF ID EX MEM WB IF ID EX MEM WB beq $1, $4, target IF ID EX MEM WB Can resolve using forwarding Chapter 4 The Processor 87
88 Data Hazards for Branches If a comparison register is a destination of preceding ALU instruction or 2 nd preceding load instruction Need 1 stall cycle lw $1, addr IF ID EX MEM WB add $4, $5, $6 IF ID EX MEM WB beq stalled IF ID beq $1, $4, target ID EX MEM WB Chapter 4 The Processor 88
89 Data Hazards for Branches If a comparison register is a destination of immediately preceding load instruction Need 2 stall cycles lw $1, addr IF ID EX MEM WB beq stalled IF ID beq stalled ID beq $1, $0, target ID EX MEM WB Chapter 4 The Processor 89
90 Dynamic Branch Prediction In deeper and superscalar pipelines, branch penalty is more significant Use dynamic prediction Branch prediction buffer (aka branch history table) Indexed by recent branch instruction addresses Stores outcome (taken/not taken) To execute a branch Check table, expect the same outcome Start fetching from fall-through or target If wrong, flush pipeline and flip prediction Chapter 4 The Processor 90
91 1-Bit Predictor: Shortcoming Inner loop branches mispredicted twice! outer: inner: beq,, inner beq,, outer Mispredict as taken on last iteration of inner loop Then mispredict as not taken on first iteration of inner loop next time around Chapter 4 The Processor 91
92 2-Bit Predictor Only change prediction on two successive mispredictions Chapter 4 The Processor 92
93 Calculating the Branch Target Even with predictor, still need to calculate the target address 1-cycle penalty for a taken branch Branch target buffer Cache of target addresses Indexed by PC when instruction fetched If hit and instruction is branch predicted taken, can fetch target immediately Chapter 4 The Processor 93
COMPUTER ORGANIZATION AND DESIGN
COMPUTER ORGANIZATION AND DESIGN 5 Edition th The Hardware/Software Interface Chapter 4 The Processor 4.1 Introduction Introduction CPU performance factors Instruction count CPI and Cycle time Determined
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface. 5 th. Edition. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle
Chapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
Pipelining Analogy. Pipelined laundry: overlapping execution. Parallelism improves performance. Four loads: Non-stop: Speedup = 8/3.5 = 2.3.
Pipelining Analogy Pipelined laundry: overlapping execution Parallelism improves performance Four loads: Speedup = 8/3.5 = 2.3 Non-stop: Speedup =2n/05n+15 2n/0.5n 1.5 4 = number of stages 4.5 An Overview
COMPUTER ORGANIZATION AND DESIGN
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle
Processor (II) - pipelining. Hwansoo Han
Processor (II) - pipelining Hwansoo Han Pipelining Analogy Pipelined laundry: overlapping execution Parallelism improves performance Four loads: Speedup = 8/3.5 =2.3 Non-stop: 2n/0.5n + 1.5 4 = number
LECTURE 3: THE PROCESSOR
LECTURE 3: THE PROCESSOR Abridged version of Patterson & Hennessy (2013):Ch.4 Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU
Full Datapath. Chapter 4 The Processor 2
Pipelining Full Datapath Chapter 4 The Processor 2 Datapath With Control Chapter 4 The Processor 3 Performance Issues Longest delay determines clock period Critical path: load instruction Instruction memory
Full Datapath. Chapter 4 The Processor 2
Pipelining Full Datapath Chapter 4 The Processor 2 Datapath With Control Chapter 4 The Processor 3 Performance Issues Longest delay determines clock period Critical path: load instruction Instruction memory
COMPUTER ORGANIZATION AND DESIGN. 5 th Edition. The Hardware/Software Interface. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle
The Processor (3) Jinkyu Jeong Computer Systems Laboratory Sungkyunkwan University
The Processor (3) Jinkyu Jeong (jinkyu@skku.edu) Computer Systems Laboratory Sungkyunkwan University http://csl.skku.edu EEE3050: Theory on Computer Architectures, Spring 2017, Jinkyu Jeong (jinkyu@skku.edu)
Chapter 4. Instruction Execution. Introduction. CPU Overview. Multiplexers. Chapter 4 The Processor 1. The Processor.
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor The Processor - Introduction
COMPUTER ORGANIZATION AND DESIGN. 5 th Edition. The Hardware/Software Interface. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition The Processor - Introduction
Pipeline Hazards. Jin-Soo Kim Computer Systems Laboratory Sungkyunkwan University
Pipeline Hazards Jin-Soo Kim (jinsookim@skku.edu) Computer Systems Laboratory Sungkyunkwan University http://csl.skku.edu Hazards What are hazards? Situations that prevent starting the next instruction
Department of Computer and IT Engineering University of Kurdistan. Computer Architecture Pipelining. By: Dr. Alireza Abdollahpouri
Department of Computer and IT Engineering University of Kurdistan Computer Architecture Pipelining By: Dr. Alireza Abdollahpouri Pipelined MIPS processor Any instruction set can be implemented in many
Chapter 4 The Processor 1. Chapter 4A. The Processor
Chapter 4 The Processor 1 Chapter 4A The Processor Chapter 4 The Processor 2 Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware
Determined by ISA and compiler. We will examine two MIPS implementations. A simplified version A more realistic pipelined version
MIPS Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
Computer Architecture Computer Science & Engineering. Chapter 4. The Processor BK TP.HCM
Computer Architecture Computer Science & Engineering Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware
Chapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware 4.1 Introduction We will examine two MIPS implementations
CSEE 3827: Fundamentals of Computer Systems
CSEE 3827: Fundamentals of Computer Systems Lecture 21 and 22 April 22 and 27, 2009 martha@cs.columbia.edu Amdahl s Law Be aware when optimizing... T = improved Taffected improvement factor + T unaffected
Chapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
Chapter 4. The Processor
Chapter 4 The Processor 4.1 Introduction Introduction CPU performance factors Instruction count CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations Determined by ISA
The Processor. Z. Jerry Shi Department of Computer Science and Engineering University of Connecticut. CSE3666: Introduction to Computer Architecture
The Processor Z. Jerry Shi Department of Computer Science and Engineering University of Connecticut CSE3666: Introduction to Computer Architecture Introduction CPU performance factors Instruction count
EIE/ENE 334 Microprocessors
EIE/ENE 334 Microprocessors Lecture 6: The Processor Week #06/07 : Dejwoot KHAWPARISUTH Adapted from Computer Organization and Design, 4 th Edition, Patterson & Hennessy, 2009, Elsevier (MK) http://webstaff.kmutt.ac.th/~dejwoot.kha/
Chapter 4. The Processor
Chapter 4 The Processor 1 Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A
Chapter 4. The Processor
Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations A simplified
The Processor: Datapath and Control. Jin-Soo Kim Computer Systems Laboratory Sungkyunkwan University
The Processor: Datapath and Control Jin-Soo Kim (jinsookim@skku.edu) Computer Systems Laboratory Sungkyunkwan University http://csl.skku.edu Introduction CPU performance factors Instruction count Determined
3/12/2014. Single Cycle (Review) CSE 2021: Computer Organization. Single Cycle with Jump. Multi-Cycle Implementation. Why Multi-Cycle?
CSE 2021: Computer Organization Single Cycle (Review) Lecture-10b CPU Design : Pipelining-1 Overview, Datapath and control Shakil M. Khan 2 Single Cycle with Jump Multi-Cycle Implementation Instruction:
Chapter 4 The Processor 1. Chapter 4B. The Processor
Chapter 4 The Processor 1 Chapter 4B The Processor Chapter 4 The Processor 2 Control Hazards Branch determines flow of control Fetching next instruction depends on branch outcome Pipeline can t always
Processor (I) - datapath & control. Hwansoo Han
Processor (I) - datapath & control Hwansoo Han Introduction CPU performance factors Instruction count - Determined by ISA and compiler CPI and Cycle time - Determined by CPU hardware We will examine two
Pipelining. CSC Friday, November 6, 2015
Pipelining CSC 211.01 Friday, November 6, 2015 Performance Issues Longest delay determines clock period Critical path: load instruction Instruction memory register file ALU data memory register file Not
Computer Architecture Computer Science & Engineering. Chapter 4. The Processor BK TP.HCM
Computer Architecture Computer Science & Engineering Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware
Computer Organization and Structure. Bing-Yu Chen National Taiwan University
Computer Organization and Structure Bing-Yu Chen National Taiwan University The Processor Logic Design Conventions Building a Datapath A Simple Implementation Scheme An Overview of Pipelining Pipelined
Chapter 4. The Processor Designing the datapath
Chapter 4 The Processor Designing the datapath Introduction CPU performance determined by Instruction Count Clock Cycles per Instruction (CPI) and Cycle time Determined by Instruction Set Architecure (ISA)
Lecture Topics. Announcements. Today: Data and Control Hazards (P&H ) Next: continued. Exam #1 returned. Milestone #5 (due 2/27)
Lecture Topics Today: Data and Control Hazards (P&H 4.7-4.8) Next: continued 1 Announcements Exam #1 returned Milestone #5 (due 2/27) Milestone #6 (due 3/13) 2 1 Review: Pipelined Implementations Pipelining
Chapter 4. The Processor. Instruction count Determined by ISA and compiler. We will examine two MIPS implementations
Chapter 4 The Processor Part I Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS implementations
The Processor (1) Jinkyu Jeong Computer Systems Laboratory Sungkyunkwan University
The Processor (1) Jinkyu Jeong (jinkyu@skku.edu) Computer Systems Laboratory Sungkyunkwan University http://csl.skku.edu EEE3050: Theory on Computer Architectures, Spring 2017, Jinkyu Jeong (jinkyu@skku.edu)
Lecture 3: The Processor (Chapter 4 of textbook) Chapter 4.1
Lecture 3: The Processor (Chapter 4 of textbook) Chapter 4.1 Introduction Chapter 4.1 Chapter 4.2 Review: MIPS (RISC) Design Principles Simplicity favors regularity fixed size instructions small number
Thomas Polzer Institut für Technische Informatik
Thomas Polzer tpolzer@ecs.tuwien.ac.at Institut für Technische Informatik Pipelined laundry: overlapping execution Parallelism improves performance Four loads: Speedup = 8/3.5 = 2.3 Non-stop: Speedup =
COMPUTER ORGANIZATION AND DESIGN. The Hardware/Software Interface. Chapter 4. The Processor: A Based on P&H
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface Chapter 4 The Processor: A Based on P&H Introduction We will examine two MIPS implementations A simplified version A more realistic pipelined
Chapter 4. The Processor. Jiang Jiang
Chapter 4 The Processor Jiang Jiang jiangjiang@ic.sjtu.edu.cn [Adapted from Computer Organization and Design, 4 th Edition, Patterson & Hennessy, 2008, MK] Chapter 4 The Processor 2 Introduction CPU performance
COMPUTER ORGANIZATION AND DESIGN
ARM COMPUTER ORGANIZATION AND DESIGN Edition The Hardware/Software Interface Chapter 4 The Processor Modified and extended by R.J. Leduc - 2016 To understand this chapter, you will need to understand some
Outline Marquette University
COEN-4710 Computer Hardware Lecture 4 Processor Part 2: Pipelining (Ch.4) Cristinel Ababei Department of Electrical and Computer Engineering Credits: Slides adapted primarily from presentations from Mike
COMPUTER ORGANIZATION AND DESI
COMPUTER ORGANIZATION AND DESIGN 5 Edition th The Hardware/Software Interface Chapter 4 The Processor 4.1 Introduction Introduction CPU performance factors Instruction count Determined by ISA and compiler
ECE260: Fundamentals of Computer Engineering
Data Hazards in a Pipelined Datapath James Moscola Dept. of Engineering & Computer Science York College of Pennsylvania Based on Computer Organization and Design, 5th Edition by Patterson & Hennessy Data
MIPS Pipelining. Computer Organization Architectures for Embedded Computing. Wednesday 8 October 14
MIPS Pipelining Computer Organization Architectures for Embedded Computing Wednesday 8 October 14 Many slides adapted from: Computer Organization and Design, Patterson & Hennessy 4th Edition, 2011, MK
Systems Architecture
Systems Architecture Lecture 15: A Simple Implementation of MIPS Jeremy R. Johnson Anatole D. Ruslanov William M. Mongan Some or all figures from Computer Organization and Design: The Hardware/Software
Chapter 4. The Processor
Chapter 4 The Processor Recall. ISA? Instruction Fetch Instruction Decode Operand Fetch Execute Result Store Next Instruction Instruction Format or Encoding how is it decoded? Location of operands and
4. The Processor Computer Architecture COMP SCI 2GA3 / SFWR ENG 2GA3. Emil Sekerinski, McMaster University, Fall Term 2015/16
4. The Processor Computer Architecture COMP SCI 2GA3 / SFWR ENG 2GA3 Emil Sekerinski, McMaster University, Fall Term 2015/16 Instruction Execution Consider simplified MIPS: lw/sw rt, offset(rs) add/sub/and/or/slt
5 th Edition. The Processor We will examine two MIPS implementations A simplified version A more realistic pipelined version
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface Chapter 4 5 th Edition Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle time Determined
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor The Processor? Chapter 4 The Processor 2 Introduction We will learn How the ISA determines many aspects
Pipelined Datapath. Reading. Sections Practice Problems: 1, 3, 8, 12 (2) Lecture notes from MKP, H. H. Lee and S.
Pipelined Datapath Lecture notes from KP, H. H. Lee and S. Yalamanchili Sections 4.5 4. Practice Problems:, 3, 8, 2 ing (2) Pipeline Performance Assume time for stages is ps for register read or write
Pipelined Datapath. Reading. Sections Practice Problems: 1, 3, 8, 12
Pipelined Datapath Lecture notes from KP, H. H. Lee and S. Yalamanchili Sections 4.5 4. Practice Problems:, 3, 8, 2 ing Note: Appendices A-E in the hardcopy text correspond to chapters 7- in the online
COMPUTER ORGANIZATION AND DESIGN. 5 th Edition. The Hardware/Software Interface. Chapter 4. The Processor
COMPUTER ORGANIZATION AND DESIGN The Hardware/Software Interface 5 th Edition Chapter 4 The Processor Introduction CPU performance factors Instruction count Determined by ISA and compiler CPI and Cycle
Chapter 4. The Processor. Computer Architecture and IC Design Lab
Chapter 4 The Processor Introduction CPU performance factors CPI Clock Cycle Time Instruction count Determined by ISA and compiler CPI and Cycle time Determined by CPU hardware We will examine two MIPS
Chapter 4 (Part II) Sequential Laundry
Chapter 4 (Part II) The Processor Baback Izadi Division of Engineering Programs bai@engr.newpaltz.edu Sequential Laundry 6 P 7 8 9 10 11 12 1 2 A T a s k O r d e r A B C D 30 30 30 30 30 30 30 30 30 30
ECE260: Fundamentals of Computer Engineering
Datapath for a Simplified Processor James Moscola Dept. of Engineering & Computer Science York College of Pennsylvania Based on Computer Organization and Design, 5th Edition by Patterson & Hennessy Introduction
Introduction. Datapath Basics
Introduction CPU performance factors - Instruction count; determined by ISA and compiler - CPI and Cycle time; determined by CPU hardware 1 We will examine a simplified MIPS implementation in this course
TDT4255 Computer Design. Lecture 4. Magnus Jahre. TDT4255 Computer Design
1 TDT4255 Computer Design Lecture 4 Magnus Jahre 2 Outline Chapter 4.1 to 4.4 A Multi-cycle Processor Appendix D 3 Chapter 4 The Processor Acknowledgement: Slides are adapted from Morgan Kaufmann companion
ECE232: Hardware Organization and Design
ECE232: Hardware Organization and Design Lecture 14: One Cycle MIPs Datapath Adapted from Computer Organization and Design, Patterson & Hennessy, UCB R-Format Instructions Read two register operands Perform
14:332:331 Pipelined Datapath
14:332:331 Pipelined Datapath I n s t r. O r d e r Inst 0 Inst 1 Inst 2 Inst 3 Inst 4 Single Cycle Disadvantages & Advantages Uses the clock cycle inefficiently the clock cycle must be timed to accommodate
Pipelined datapath Staging data. CS2504, Spring'2007 Dimitris Nikolopoulos
Pipelined datapath Staging data b 55 Life of a load in the MIPS pipeline Note: both the instruction and the incremented PC value need to be forwarded in the next stage (in case the instruction is a beq)
ECE260: Fundamentals of Computer Engineering
Pipelining James Moscola Dept. of Engineering & Computer Science York College of Pennsylvania Based on Computer Organization and Design, 5th Edition by Patterson & Hennessy What is Pipelining? Pipelining
ELE 655 Microprocessor System Design
ELE 655 Microprocessor System Design Section 2 Instruction Level Parallelism Class 1 Basic Pipeline Notes: Reg shows up two places but actually is the same register file Writes occur on the second half
zhandling Data Hazards The objectives of this module are to discuss how data hazards are handled in general and also in the MIPS architecture.
zhandling Data Hazards The objectives of this module are to discuss how data hazards are handled in general and also in the MIPS architecture. We have already discussed in the previous module that true
CENG 3420 Lecture 06: Pipeline
CENG 3420 Lecture 06: Pipeline Bei Yu byu@cse.cuhk.edu.hk CENG3420 L06.1 Spring 2019 Outline q Pipeline Motivations q Pipeline Hazards q Exceptions q Background: Flip-Flop Control Signals CENG3420 L06.2
Introduction. Chapter 4. Instruction Execution. CPU Overview. University of the District of Columbia 30 September, Chapter 4 The Processor 1
Chapter 4 The Processor Introduction CPU performance factors Instruction count etermined by IS and compiler CPI and Cycle time etermined by CPU hardware We will examine two MIPS implementations simplified
Lecture 2: Processor and Pipelining 1
The Simple BIG Picture! Chapter 3 Additional Slides The Processor and Pipelining CENG 6332 2 Datapath vs Control Datapath signals Control Points Controller Datapath: Storage, FU, interconnect sufficient
LECTURE 9. Pipeline Hazards
LECTURE 9 Pipeline Hazards PIPELINED DATAPATH AND CONTROL In the previous lecture, we finalized the pipelined datapath for instruction sequences which do not include hazards of any kind. Remember that
ECE473 Computer Architecture and Organization. Pipeline: Data Hazards
Computer Architecture and Organization Pipeline: Data Hazards Lecturer: Prof. Yifeng Zhu Fall, 2015 Portions of these slides are derived from: Dave Patterson UCB Lec 14.1 Pipelining Outline Introduction
1 Hazards COMP2611 Fall 2015 Pipelined Processor
1 Hazards Dependences in Programs 2 Data dependence Example: lw $1, 200($2) add $3, $4, $1 add can t do ID (i.e., read register $1) until lw updates $1 Control dependence Example: bne $1, $2, target add
EE557--FALL 1999 MIDTERM 1. Closed books, closed notes
NAME: SOLUTIONS STUDENT NUMBER: EE557--FALL 1999 MIDTERM 1 Closed books, closed notes GRADING POLICY: The front page of your exam shows your total numerical score out of 75. The highest numerical score
Lecture Topics. Announcements. Today: Single-Cycle Processors (P&H ) Next: continued. Milestone #3 (due 2/9) Milestone #4 (due 2/23)
Lecture Topics Today: Single-Cycle Processors (P&H 4.1-4.4) Next: continued 1 Announcements Milestone #3 (due 2/9) Milestone #4 (due 2/23) Exam #1 (Wednesday, 2/15) 2 1 Exam #1 Wednesday, 2/15 (3:00-4:20
DEE 1053 Computer Organization Lecture 6: Pipelining
Dept. Electronics Engineering, National Chiao Tung University DEE 1053 Computer Organization Lecture 6: Pipelining Dr. Tian-Sheuan Chang tschang@twins.ee.nctu.edu.tw Dept. Electronics Engineering National
CS 251, Winter 2018, Assignment % of course mark
CS 251, Winter 2018, Assignment 5.0.4 3% of course mark Due Wednesday, March 21st, 4:30PM Lates accepted until 10:00am March 22nd with a 15% penalty 1. (10 points) The code sequence below executes on a
The MIPS Processor Datapath
The MIPS Processor Datapath Module Outline MIPS datapath implementation Register File, Instruction memory, Data memory Instruction interpretation and execution. Combinational control Assignment: Datapath
Full Datapath. CSCI 402: Computer Architectures. The Processor (2) 3/21/19. Fengguang Song Department of Computer & Information Science IUPUI
CSCI 42: Computer Architectures The Processor (2) Fengguang Song Department of Computer & Information Science IUPUI Full Datapath Branch Target Instruction Fetch Immediate 4 Today s Contents We have looked
CSCI 402: Computer Architectures. Fengguang Song Department of Computer & Information Science IUPUI. Today s Content
3/6/8 CSCI 42: Computer Architectures The Processor (2) Fengguang Song Department of Computer & Information Science IUPUI Today s Content We have looked at how to design a Data Path. 4.4, 4.5 We will design
CS 110 Computer Architecture. Pipelining. Guest Lecture: Shu Yin. School of Information Science and Technology SIST
CS 110 Computer Architecture Pipelining Guest Lecture: Shu Yin http://shtech.org/courses/ca/ School of Information Science and Technology SIST ShanghaiTech University Slides based on UC Berkley's CS61C
ECS 154B Computer Architecture II Spring 2009
ECS 154B Computer Architecture II Spring 2009 Pipelining Datapath and Control 6.2-6.3 Partially adapted from slides by Mary Jane Irwin, Penn State And Kurtis Kredo, UCD Pipelined CPU Break execution into
Outline. A pipelined datapath Pipelined control Data hazards and forwarding Data hazards and stalls Branch (control) hazards Exception
Outline A pipelined datapath Pipelined control Data hazards and forwarding Data hazards and stalls Branch (control) hazards Exception 1 4 Which stage is the branch decision made? Case 1: 0 M u x 1 Add
CS 251, Winter 2019, Assignment % of course mark
CS 251, Winter 2019, Assignment 5.1.1 3% of course mark Due Wednesday, March 27th, 5:30PM Lates accepted until 1:00pm March 28th with a 15% penalty 1. (10 points) The code sequence below executes on a
Data Hazards Compiler Scheduling Pipeline scheduling or instruction scheduling: Compiler generates code to eliminate hazard
Data Hazards Compiler Scheduling Pipeline scheduling or instruction scheduling: Compiler generates code to eliminate hazard Consider: a = b + c; d = e - f; Assume loads have a latency of one clock cycle:
The Processor: Improving the performance - Control Hazards
The Processor: Improving the performance - Control Hazards Wednesday 14 October 15 Many slides adapted from: and Design, Patterson & Hennessy 5th Edition, 2014, MK and from Prof. Mary Jane Irwin, PSU Summary
CS 61C: Great Ideas in Computer Architecture Pipelining and Hazards
CS 61C: Great Ideas in Computer Architecture Pipelining and Hazards Instructors: Vladimir Stojanovic and Nicholas Weaver http://inst.eecs.berkeley.edu/~cs61c/sp16 1 Pipelined Execution Representation Time
COMP2611: Computer Organization. The Pipelined Processor
COMP2611: Computer Organization The 1 2 Background 2 High-Performance Processors 3 Two techniques for designing high-performance processors by exploiting parallelism: Multiprocessing: parallelism among
Single Cycle Datapath
Single Cycle atapath Lecture notes from MKP, H. H. Lee and S. Yalamanchili Section 4.-4.4 Appendices B.7, B.8, B.,.2 Practice Problems:, 4, 6, 9 ing (2) Introduction We will examine two MIPS implementations
ECE 154A Introduction to. Fall 2012
ECE 154A Introduction to Computer Architecture Fall 2012 Dmitri Strukov Lecture 10 Floating point review Pipelined design IEEE Floating Point Format single: 8 bits double: 11 bits single: 23 bits double:
Computer Organization and Structure
Computer Organization and Structure 1. Assuming the following repeating pattern (e.g., in a loop) of branch outcomes: Branch outcomes a. T, T, NT, T b. T, T, T, NT, NT Homework #4 Due: 2014/12/9 a. What
CS 2506 Computer Organization II Test 2. Do not start the test until instructed to do so! printed
Instructions: Print your name in the space provided below. This examination is closed book and closed notes, aside from the permitted fact sheet, with a restriction: 1) one 8.5x11 sheet, both sides, handwritten
Computer and Information Sciences College / Computer Science Department Enhancing Performance with Pipelining
Computer and Information Sciences College / Computer Science Department Enhancing Performance with Pipelining Single-Cycle Design Problems Assuming fixed-period clock every instruction datapath uses one
Single Cycle Datapath
Single Cycle atapath Lecture notes from MKP, H. H. Lee and S. Yalamanchili Section 4.1-4.4 Appendices B.3, B.7, B.8, B.11,.2 ing Note: Appendices A-E in the hardcopy text correspond to chapters 7-11 in
COSC 6385 Computer Architecture - Pipelining
COSC 6385 Computer Architecture - Pipelining Fall 2006 Some of the slides are based on a lecture by David Culler, Instruction Set Architecture Relevant features for distinguishing ISA s Internal storage
Improving Performance: Pipelining
Improving Performance: Pipelining Memory General registers Memory ID EXE MEM WB Instruction Fetch (includes PC increment) ID Instruction Decode + fetching values from general purpose registers EXE EXEcute
Inf2C - Computer Systems Lecture Processor Design Single Cycle
Inf2C - Computer Systems Lecture 10-11 Processor Design Single Cycle Boris Grot School of Informatics University of Edinburgh Previous lectures Combinational circuits Combinations of gates (INV, AND, OR,
ECE Exam II - Solutions November 8 th, 2017
ECE 3056 Exam II - Solutions November 8 th, 2017 1. (15 pts) To the base pipeline we add data forwarding to EX, data hazard detection and stall generation, and branches implemented in MEM and predicted
Question 1: (20 points) For this question, refer to the following pipeline architecture.
This is the Mid Term exam given in Fall 2018. Note that Question 2(a) was a homework problem this term (was not a homework problem in Fall 2018). Also, Questions 6, 7 and half of 5 are from Chapter 5,
Instruction word R0 R1 R2 R3 R4 R5 R6 R8 R12 R31
4.16 Exercises 419 Exercise 4.11 In this exercise we examine in detail how an instruction is executed in a single-cycle datapath. Problems in this exercise refer to a clock cycle in which the processor
CS/CoE 1541 Mid Term Exam (Fall 2018).
CS/CoE 1541 Mid Term Exam (Fall 2018). Name: Question 1: (6+3+3+4+4=20 points) For this question, refer to the following pipeline architecture. a) Consider the execution of the following code (5 instructions)
Design a MIPS Processor (2/2)
93-2Digital System Design Design a MIPS Processor (2/2) Lecturer: Chihhao Chao Advisor: Prof. An-Yeu Wu 2005/5/13 Friday ACCESS IC LABORTORY Outline v 6.1 An Overview of Pipelining v 6.2 A Pipelined Datapath