ALPHA/A.LEDA SERIES RDM PROTOCOL DEFINITION

Transcription

1 ENGLISH RDM PROTOCOL DEFINITION THIS DOCUMENT REFERS TO : ANSI E1.0 00, ENTERTAINMENT TECHNOLOGY RDM - REMOTE DEVICE MANAGEMENT OVER DMX51 NETWORKS CP/ R4 INDEX INDEX Page Contents Page Contents CLAYPAKY ALPHA/ALEDA SERIES RDM PROTOCOL DEFINITION Display Setting Parameter Messages DISPLAY_INVERT Product Information Messages DEVICE_INFO PROD_DETAIL_ID_LIST DEVICE_MODEL_DESC DEVICE_LABEL MANUFACTURER_LABEL SWVER_LABEL BOOT_SWVER_LABEL BOOT_SWVER_ID RDM Information Messages SUPPORTED_PARAMETERS DMX51 Setup Messages DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION DMX_START_ADDRESS SLOT_INFO SLOT_DESCRIPTION DEFAULT_SLOT_VALUE Sensor Parameter Messages SENSOR_DEFINITION SENSOR_VALUE Device Control Parameter Messages IDENTIFY_DEVICE Device Configuration Parameter Messages PAN_INVERT TILT_INVERT PAN_TILT_SWAP Power/Lamp Setting Parameter Messages DEVICE_HOURS LAMP_HOURS LAMP_ON_MODE 9 LAMP_STATE CLAY PAKY User defined PIDS CP_PROPS CLAY PAKY User defined parameters CP_DISPLAYON CP_FIXTID CP_EVAN_RGBCMY CP_FIXWHEELSC CP_LAMPONDMX CP_ENCPT CP_DIMMERCURVE CP_SILENTMODE CP_SHUTTERONERR CP_DIMMONSHUTTER CP_POWERFANSMODE CP_ARTNET_MODE CP_NETREPEATDMX CP_UNIVERSE CP_AFAUTOSCALEOFF CP_MCOLORADJUST CP_MEFFRANDID CP_MEFFDISTRIB CP_EVANCURVEMODE CP_CWHEEL_LINEAR 1

2 Available Parameters ID(PID): DEVICE_INFO PRODUCT INFORMATION MESSAGES This parameter is used to retrieve a variety of information about the device that is normally required by a controller. All the parameters are filled as requested by the standard, the Product Category field is set to MOVING YOKE. PROD_DETAIL_ID_LIST This parameter shall be used for requesting technology details for a device. The response is a packed message containing up to six product detail identifications. Detail list: PRODUCT_DETAIL_ARC PRODUCT_DETAIL_LED (Aleda Wash Models Only) PRODUCT_DETAIL_COLORSCROLLER PRODUCT_DETAIL_COLORWHEEL PRODUCT_DETAIL_IRIS_DOUSER PRODUCT_DETAIL_DIMMING_SHUTTER PRODUCT_DETAIL_PROFILE_SHUTTER (Alpha Profile Models Only) DEVICE_MODEL_DESC This parameter provides a text description of up to 3 characters for the device model type. DEVICE_LABEL This parameter provides a means of setting a descriptive label for each device. It shows the fixtures names. E.G. Aleda Wash K0 MANUFACTURER_LABEL This parameter provides an ASCII text response with the Manufacturer name for the device. Clay Paky is the default name. SWVER_LABEL This parameter is used to get a descriptive ASCII text label for the device s operating software version. BOOT_SWVER_LABEL This parameter is used to get a descriptive ASCII text label for the Boot Version of the software for Devices that support this functionality. Example: 1.9. BOOT_SWVER_ID This parameter is used to retrieve the unique Boot Software Version ID for the device. Example: 0019.

3 SUPPORTED_PARAMETERS This message is used to retrieve a packed list of supported PIDs. Supported Parameters List: PROD_DETAIL_ID_LIST DEVICE_MODEL_DESC MANUFACTURER_LABEL DEVICE_LABEL BOOT_SWVER_ID BOOT_SWVER_LABEL DMX_PERSONALITY DMX_PERSONALITY_DESCRIPTION SLOT_INFO SLOT_DESCRIPTION DEFAULT_SLOT_VALUE SENSOR_DEFINITION SENSOR_VALUE DEVICE_HOURS LAMP_HOURS LAMP_STRIKES LAMP_STATE LAMP_ON_MODE DISPLAY_INVERT PAN_INVERT TILT_INVERT PAN_TILT_SWA RDM INFORMATION MESSAGES DMX_PERSONALITY This parameter is used to get or set the responder s DMX51 Personality. Available Peronality: Aleda Wash Models 1 = Standard = Shapes 3 = Extended 4 = Extended RGBW Alpha Models 1 = Standard = Vector ShotLight Wash Model 1 = Synchronized = Synchronized + Vector 3 = Independent 4 = Independent + Vector DMX51 SETUP MESSAGES DMX_PERSONALITY_DESCRIPTION This parameter is used to get a descriptive ASCII text label for a given DMX51 Personality. Description label example : Extended RGBW. DMX_START_ADDRESS This parameter is used to set or get the DMX51 start address. 3 Continue

4 SLOT_INFO This parameter is used to retrieve basic information about the functionality of the DMX51 slots used to control the device. Implemented Slot Types and Definition: LABEL DEFINITION TYPE Cyan SD_COLOR_SUB_CYAN ST_PRIMARY Magenta SD_COLOR_SUB_MAGENTA ST_PRIMARY Yellow SD_COLOR_SUB_YELLOW ST_PRIMARY CTO SD_COLOR_CORRECTION ST_PRIMARY Color wheel SD_COLOR_WHEEL ST_PRIMARY Colour time SD_COLOR_WHEEL ST_SEC_TIMING Strobe SD_STROBE ST_PRIMARY Dimmer SD_INTENSITY_MASTER ST_PRIMARY Beam time SD_INTENSITY_MASTER ST_SEC_TIMING Dimmer fine SD_INTENSITY_MASTER ST_SEC_FINE Iris SD_BEAM_SIZE_IRIS ST_PRIMARY Fix gobo chg SD_STATIC_GOBO_WHEEL ST_PRIMARY Gobo time SD_STATIC_GOBO_WHEEL ST_SEC_TIMING Rot gobo chg SD_ROTO_GOBO_WHEEL ST_PRIMARY Gobo time SD_ROTO_GOBO_WHEEL ST_SEC_TIMING Gobo rotation SD_ROTO_GOBO_WHEEL ST_SEC_INDEX_ROTATE Gobo fine SD_ROTO_GOBO_WHEEL ST_SEC_FINE Beam shaper ins. SD_PRISM_WHEEL ST_PRIMARY Prism Ins SD_PRISM_WHEEL ST_PRIMARY Ovalizer SD_PRISM_WHEEL ST_PRIMARY Beam shaper rot. SD_PRISM_WHEEL ST_SEC_INDEX_ROTATE Ovalizer rotat SD_PRISM_WHEEL ST_SEC_INDEX_ROTATE Frost SD_FROST ST_PRIMARY Frost ins. SD_FROST ST_PRIMARY AnimDiskIns SD_EFFECTS_WHEEL ST_PRIMARY AnimDiskRot SD_EFFECTS_WHEEL ST_SEC_ROTATION BladeUp1 SD_FRAMING_SHUTTER ST_PRIMARY BladeUp SD_FRAMING_SHUTTER ST_PRIMARY BladeDw1 SD_FRAMING_SHUTTER ST_PRIMARY BladeDw SD_FRAMING_SHUTTER ST_PRIMARY BladeLf1 SD_FRAMING_SHUTTER ST_PRIMARY BladeLf SD_FRAMING_SHUTTER ST_PRIMARY BladeRg1 SD_FRAMING_SHUTTER ST_PRIMARY BladeRg SD_FRAMING_SHUTTER ST_PRIMARY FrameRotat SD_SHUTTER_ROTATE ST_PRIMARY Focus SD_EDGE ST_PRIMARY Focus fine SD_EDGE ST_SEC_FINE Zoom SD_ZOOM ST_PRIMARY Macro Effects SD_MACRO ST_PRIMARY Macro Colour SD_COLOR_SCROLL ST_PRIMARY Lamp On/Off SD_LAMP_CONTROL ST_PRIMARY Function SD_FIXTURE_CONTROL ST_PRIMARY Reset SD_FIXTURE_CONTROL ST_PRIMARY Pan SD_PAN ST_PRIMARY P/T time SD_PAN ST_SEC_TIMING Pan fine SD_PAN ST_SEC_FINE Tilt SD_TILT ST_PRIMARY Tilt fine SD_TILT ST_SEC_FINE 4

5 SLOT_DESCRIPTION This parameter is used for requesting an ASCII text description for DMX51 slot offsets. DEFAULT_SLOT_VALUE This parameter shall be used for requesting the default values for the given DMX51 slot offsets for a device. SENSOR_DEFINITION This parameter is used to retrieve the definition of a specific sensor. Sensors definition fields: Sensor ID Sensor Type (See table A.1 Ansi E1.0 specifications) Sensor Unit (See table A.13 Ansi E1.0 specifications) Sensor Prefix (See table A.14 Ansi E1.0 specifications) Min/Max Range Normal Min/Max Range Recorded Value Support Sensor Description SENSOR PARAMETER MESSAGES Note: For the Recorded Value Support only the Lowest/Highest values are supported. Alpha Series monitored sensors: Fans Aleda Series monitored sensors: Fans Modules Temperature Example: Fan : Power Supply Sensor ID = 0 Sensor Type = 3 (Frequency) Sensor Unit = 8 (Hertz) Sensor Prefix = (Centi) Min Range = 1 Max Range = Normal Min Range = 350 Normal Max Range = 541 Recorded Value Support = (Lowest/Highest Detected Values Supported ) Sensor Description = FAN: Power Supply SENSOR_VALUE This parameter shall be used to retrieve or reset sensor data. Sensors value fields: Sensor ID Present Value Lowest Value Highest Value Recorded Value Example: Fan : Power Supply Sensor ID = 0 Present Value = 5110 Lowest Value = 0 Highest Value = 511 Recorded Value = 0 ( Not supported ) Note: The RDM Standard does not provide RPM as Unit value and the Fan speed is expressed in Hertz. If you want the correspondig RPM value use the following formula Present Value * 0 / 100 (the prefix is Centi). 5

6 IDENTIFY_DEVICE DEVICE CONTROL PARAMETER MESSAGES This parameter is used for the user to physically identify the device represented by the UID. PAN_INVERT This parameter is used to retrieve or change the Pan Invert setting. DEVICE CONFIGURATION PARAMETER MESSAGES TILT_INVERT This parameter is used to retrieve or change the Tilt Invert setting. PAN_TILT_SWAP This parameter is used to retrieve or change the Pan/Tilt Swap setting. DISPLAY_INVERT This parameter is used to retrieve or change the Display Invert setting. DISPLAY SETTING PARAMETER MESSAGES POWER/LAMP SETTING PARAMETER MESSAGES DEVICE_HOURS This parameter is used to retrieve or set the number of hours of operation the device has been in use. Note: For the Claypaky Firmware the SET instruction can only reset the counter to 0. The value sent must be 0, any other value is ignored. LAMP_HOURS This parameter is used to retrieve the number of lamp hours or to set the counter in the device to a specific starting value. Note: For the Claypaky Firmware the SET instruction can only reset the counter to 0. The value sent must be 0, any other value is ignored. LAMP_STRIKES This parameter is used to retrieve the number of lamp strikes or to set the counter in the device to a specific starting value. Note: For the Claypaky Firmware the SET instruction can only reset the counter to 0. The value sent must be 0, any other value is ignored. LAMP_ON_MODE This parameter is used to retrieve or change the current Lamp On Mode. LAMP_STATE This parameter is used to retrieve or change the current operating state of the lamp.

7 CP_PROPS Parameter ID: 0x80A0 This parameter is used to get a description of a User defined parameter. Controller: CLAY PAKY USER DEFINED PIDS (Port ID) (Message Count) (SubDevice) 0x00-0xFF 0x00 0x0000 (Root) or 0x0001-0x000 or 0xFFFF (CC) (PID) (PDL) GET_COMMAND CP_PROPS 0X01 User defined parameter ID (1 bit) String Offset (1 bit) (PD) Response: (Response Type) (Message Count) (SubDevice) ACK 0x00-0xFF Copy of Controller SD (CC) (PID) (PDL) GET_COMMAND _RESPONSE CP_PROPS 3 35 (3 + Number of characters sent) User defined parameter ID (1 bit) Type Minimim Value (1 bit) Maximum Value (1 bit) Text label descriptions (PD) 7 Continue

8 Data Description: User defined parameter ID (1 bit): The requested parameter ID listed in the ClayPaky User Parameters Table. Type: Type is an 8-bit value that defines the type of data that is contained in the response. Type Values descpription Table: TYPE VALUE DESCRIPTION Unsigned Integer 8 Bit 0 Values from 0 to 55 Unsigned Integer 1 Bit 1 Values from 0 to 5535 Unsigned Integer 3 Bit Values from 0 to 3-1 Signed Integer 8 Bit 3 Values from -18 to 17 Signed Integer 1 Bit 4 Values from to 3.77 Signed Integer 3 Bit 5 Values from -31 to 31-1 On/Off Value 0 = On, 1 = Off Enum 7 String values with associated text Minimum Value: This is a s compliment signed 1-bit value that represents the lowest value that the User parameter can assume. Maximum Value: This is a s compliment signed 1-bit value that represents the highest value that the User parameter can assume. Text label Description: This field is requested only for Enum types. A series of zero separated ASCII strings describe each value of the parameter. The field is filled with text description values until there is space available in the PD. The Controller must check the number of descriptions returned, and if it had received less than expected (max-min +1), it should resend the command by storing, in the field "String offset", the text description index from which to start. This operation must be repeated until all the text description have been received. Example of an Enum parameter with a range of 0-1: 0 = Limited range 1 = Full range. The Text label description field is filled as following: Limited range + chr(0) + Full range + chr(0). String Offset: This field is used in the event of multiple requests when there is not enough space to store all the description values in the PD. At the first request, the field must be set to zero. Subsequent requests must be set with the offset(index) of the description to start with. 8

9 CLAY PAKY USER DEFINED PARAMETERS The following parameters are CLAYPAKY's-specific codes used to set the parameters in the Fixture's User Menu via RDM. In the RDM Standard, the Manufacturer's-specific codes can be defined in the range of 0x8000 0xFFDF. CLAYPAKY USER PARAMETERS TABLE PID NAME ID TYPE CP_DISPLAYON 0x8500 DS_UNSIGNED_BYTE (0) CP_FIXTID 0x800 DS_UNSIGNED_BYTE (0) CP_EVAN_RGBCMY 0x801 DS_UNSIGNED_BYTE (0) CP_FIXWHEELSC 0x80 DS_UNSIGNED_BYTE (0) CP_LAMPONDMX 0x803 DS_UNSIGNED_BYTE (0) CP_ENCPT 0x804 DS_UNSIGNED_BYTE (0) CP_PTSPEEDMODE 0x805 DS_UNSIGNED_BYTE (0) CP_DIMMERCURVE 0x80 DS_UNSIGNED_BYTE (0) CP_SILENTMODE 0x807 DS_UNSIGNED_BYTE (0) CP_SHUTTERONERR 0x808 DS_UNSIGNED_BYTE (0) CP_DIMMONSHUTTER 0x809 DS_UNSIGNED_BYTE (0) CP_POWERFANSMODE 0x80A DS_UNSIGNED_BYTE (0) CP_ARTNET_MODE 0x80B DS_UNSIGNED_BYTE (0) CP_NETREPEATDMX 0x80C DS_UNSIGNED_BYTE (0) CP_UNIVERSE 0x80D DS_UNSIGNED_BYTE (0) CP_AFAUTOSCALEOFF 0x80E DS_UNSIGNED_BYTE (0) CP_MCOLORADJUST 0x80F DS_UNSIGNED_BYTE (0) CP_MEFFRANDID 0x810 DS_UNSIGNED_BYTE (0) CP_MEFFDISTRIB 0x811 DS_UNSIGNED_BYTE (0) CP_EVANCURVEMODE 0x81 DS_UNSIGNED_BYTE (0) CP_PT_HOMING_SPEC 0x813 DS_UNSIGNED_BYTE (0) CP_PAN_HOME_ANGLE 0x814 DS_UNSIGNED_BYTE (0) CP_TILT_HOME_ANGLE 0x815 DS_UNSIGNED_BYTE (0) CP_CWHEEL_LINEAR 0x81 DS_UNSIGNED_BYTE (0) CP_DISPLAYON Used for automatically reduce brightness on the display after about 30 seconds. in idle. 0 = OFF 1 = ON CP_FIXTID This parameter is used to retrieve or change the fixture id address. Max: 55 numeric value from min to max. 9 Continue

10 CP_EVAN_RGBCMY This parameter is used for reversing the CMY color mixing system.. Unavailable on Sharpy, AledaK5, AledaK10, AledaK0 models. 0 = OFF 1 = ON CP_FIXWHEELSC This parameter is used for optimizing color change time so that the disc turns in the direction that requires shorter movement. Unavailable on AledaK5,AledaK10,AledaK0 models. 0 = OFF 1 = ON CP_LAMPONDMX This parameter is used for enabling lamp remote control channel. Unavailable on AledaK5,AledaK10,AledaK0 models. 0 = OFF 1 = ON CP_ENCPT This parameter is used for enabling the Pan / Tilt encoders. 0 = OFF 1 = ON CP_PTSPEEDMODE This parameter is used to adjust the Pan/Tilt speed. The default mode is Fast. 0 = Standard 1 = Fast CP_DIMMERCURVE This parameter is used to retrieve or change the Dimmer Curve. 0 = Conventional 1 = Linear 10

11 CP_SILENTMODE This parameter is used to select the Silent Mode from the two available. Available on AlphaSpotHpe1500, AlphaWash1500, AlphaProfile1500, AlphaProf1500Q, ShotLightWash, AledaK5, AledaK10, AledaK0 models only. 0 = Standard 1 = Quiet CP_SHUTTERONERR This parameter is used for automatically closing the stop/strobe in the event of Pan / Tilt position error. 0 = ON 1 = OFF CP_DIMMONSHUTTER This parameter is used to enable automatic closing of the dimmer when the strobe is completely closed. Unavailable on Sharpy model. 0 = ON 1 = OFF CP_POWERFANSMODE This parameter is used to retrieve or change the Power Mode. It takes on a different meaning for each model. AlphaSpotHPE700, AlphaWash700, AlphaBeam700, AlphaProfile700 models: Max: 0 = 4-700W Full fan speed 1 = 400W Low fan speed = 4-700W Auto fan speed AlphaSpotQWO800 model: Max: 0 = 5-800W Full fan speed 1 = 500W Low fan speed = 5-800W Auto fan speed AlphaSpotHpe1500, AlphaWash1500, AlphaProfile1500, AlphaProf1500Q, ShotLightWash models: Max: 0 = W Full fan speed 1 = 100W Low fan speed = W Auto fan speed 11 Continue

12 CP_ARTNET_MODE This parameter is used to select the Control Protocol Art-net to assign according to the control unit used: Max: 0 = Disabled 1 = Art-net on IP.x.x.x = Art-net on IP 10.x.x.x CP_NETREPEATDMX This parameter is used to enable the transmission of the Ethernet protocol by DMX signal to all the connected projectors. 0 = Disabled 1 = Enabled on primary CP_UNIVERSE This parameter is used to assign the Univers numer to be assigned to a series of projectors. Max: 55 Numeric value from min to max. CP_AFAUTOSCALEOFF This parameter is used to select the Auto-focus Mode. Available on AlphaSpotHpe1500, AlphaProfile1500, AlphaProf1500Q, AlphaProfile700 models only. 0 = Limited Zoom Range 1 = Complete Zoom Range CP_MCOLORADJUST This parameter is used to enable the overwritting of a Macro Colour with the Cyan, Magenta, Yellow, CTO, and Colour wheel channels. Available on AlphaSpotHpe1500, AlphaWash1500, AlphaProfile1500, AlphaProf1500Q, AlphaProfile700, ShotLightWash,AlphaSpotQWO800, AledaK5, AledaK10, AledaK0 m odels only. 0 = ON 1 = OFF CP_MEFFRANDID This parameter is used to attribute an ID address to the projector for the phase displacement for the scene's starting time in Macro mode. Available on AlphaSpotHpe1500, AlphaProfile1500, AlphaProf1500Q,AlphaProfile700, ShotLightWash models only. Max: X 0 = Auto by DMX address X = To assign to all projectors to be included in the Macro operation 1

13 CP_MEFFDISTRIB This parameter is used to se the number of projectors to be included in the Macro mode operation. Min: 5 numeric value from min to max. CP_EVANCURVEMODE This parameter is used to select the Color mixing curve. Available on AlphaSpotHPE700, AlphaWash700, AlphaBeam700, AlphaProfile700, AlphaSpotQWO800 models only. 0 = Curve 1 1 = Curve CP_PT_HOMING_SPEC This parameter is used to change the Pan/Tilt homing sequence. The default value is 0 causing the Pan and Tilt to run the homing routine at the same time. If the parameter is 1 the homing routine will be sequenced. 0 = False 1 = True CP_PAN_HOME_ANGLE This parameter is used to define the default homing rotation angle of Pan. Max: 3 0 = 0 1 = 90 = = 70 CP_TILT_HOME_ANGLE This parameter is used to define the default homing rotation angle percentage of Tilt. Max: 0 = 0% 1 = 1,5% = 5% 3 = 50% 4 = 75% 5 = 87,5% = 100% CP_CWHEEL_LINEAR This parameter is used to enable the Color Wheel Linear movement. Available on Sharpy, SharpWash330 models only. 0 = ON 1 = OFF 13

14 14

15 15

16 CLAY PAKY S.p.A. - Via Pastrengo, 3/b Seriate (BG) Italy - Tel Fax IST00E/001 EN - Rev.0 09/13