RA /2.95. Gear Pump Model G2 (Series 4X) For Flange Mounting with SAE threaded Ports. Functional description. Symbols
|
|
- Ashley Rice
- 5 years ago
- Views:
Transcription
1 /2.9 Gear Pump Model G2 (Series X For Flange Mounting with SE threaded Ports s to PSI (2 bar....7 in /rev. (22. cm /rev. /2.9 eplaces: 2.92 New principle of sealing the pump body, increases service life Long seal life, even at maximum temperatures Sleeve bearings for long life Single block bearings Heavy duty construction Innovative principle of hydrostatic compensation 8/ PF 2 G2-X/... 2 M Functional description Hydraulic pumps, model G2, are self-priming, external gear pumps. pplicable to 6 PSI (2 bar, these fixed displacement pumps provide flow to operate hydraulic circuits. Consisting of housing (, mounting flange (2, drive shaft (, bearing blocks (, sleeve bearings (, and hydrostatic compensation plates (6. G2 series gear pumps are designed to handle the rigors of industrial use. otation of the gears creates a void at the suction inlet (7. Fluid trapped in the gear roots is transported to the pressure port (8. This merging of fluid creates flow, which reflects a pressure signal as a result of load forces. s evident by the cross-section, any void created at the suction inlet will immediately be replaced by reservoir fluid. To enhance smooth performance, a small volume of load-pressurized-fluid is needed to aid in internal lubrication Suction side 8 Pressure side 9 Driving gear (clockwise Driven gear 8 2 Symbols Single pump P Tandem pump P P S S S
2 /2.9 Ordering code Series to 9 = X ( to 9, externally interchangeable Displacement.2 in /rev (. cm /rev =. in /rev (. cm /rev =. in /rev (8.2 cm /rev 8 = 8.67 in /rev (. cm /rev =.86 in /rev (. cm /rev =.99 in /rev (6.2 cm /rev 6 = 6.6 in /rev (9. cm /rev 9 = 9.7 in /rev (22. cm /rev 22 = 22 Clockwise = * Counter-clockwise = L Splined shaft SE- /8", 9 teeth = * Tapered shaft : Ø 7 mm = C Tongued shaft with coupling for single pump, center or rear pump = N Tapered shaft : Ø 2 mm for use with additional front bearing = S Keyed shaft, 8 mm Ø = 2 - special order, only on request PF 2 G2 - X 2 M Sample order codes for single pumps PF 2 G2-X/ 2 M (front pump only PF 2 G2-X/6 2 MK (rear pump only PF 2 G2-X/8 LN 2 MDL Ordering code for combination pump G2/8 + G2/ Sample order code for multiple pumps PF 2 G2-X/8 2 MK PF 2 G2-X/ LN 2 MDL Further details to be written in clear text * no desig = Single pump K = Front pump of combination L = ear pump of combination N = Center pump of combination * = SE-, 2-bolt.2" (82. mm pilot = rectangular flange 8 mm pilot P = 2-bolt mounting mm pilot M = 2-bolt mounting 2 mm pilot = front bearing assembly 8 mm pilot D = Combination flange for G2 + G2 (ear and Center pumps only H = combination flange when mounting G2 to larger pumps G, G, (ear and Center Pumps only * M = una-n seals up to 76 F (8 C K = FPM Shaft Seal, other seals in una-n (for connection to diesel engine *2 2 = SE Straight threaded ports (only available with SE splined shaft and mounting 2 = Square metric flange design = SP thread port For splined coupling, see PU- -8 For pump mounting brackets, see 2 For metric flanges, see 2 * Typical Stock: PF 2 G2-X/ 2 M 2 See chart below for fluid port dimensions Shaft type only with ports Multiple pumps are delivered completely assembled. The components allowing for this assembly are, however, to be shown as separate items within the order (see sample order. It is possible to order combination parts singularly. For details, see the sample order for multiple pumps. The kit consists of: two tie rods, two washers and two nuts. The coupling is included with the rear or center pump. Ordering code for combination pump G2/22 + G2/ + G2/ PF 2 G2-X/22 2 MK + PF 2 G2-X/ LN 2 MDN + PF 2 G2-X/ LN 2 MDL Fluid port dimensions for Port Code 2 Dimensions Weight in inches (mm P S lbs (kg.8 (9.7 (. SE-; 7/8- SE-; 7/8-7.7 (..8 (9.7 (. SE-; 7/8- SE-; 7/8-7.9 ( (9..8 (.7 SE-; 7/8- SE-2; / (.6.86 (98.89 (8 SE-; 7/8- SE-2; / (.8.2 (2.97 ( SE-; 7/8- SE-2; / (.8 6. ( 2. (. SE-; 7/8- SE-2; / ( (9 2. (. SE-; 7/8- SE-2; / ( ( (8 SE-; 7/8- SE-2; / (. *
3 Technical data (for application outside these parameters, please consult us! Hydraulic fluid: Petroleum oils to data sheet 7 7 Maximum degree of fluid contamination: Class 9/6, according to ISO 6. Therefore, we recommend a filter with a minimum retention rate of ß 2. (For longer life, we recommend class 8/, achievable with a filter ß. Fluid temperature range: to 76 F ( to 8 C mbient temperature range: to F ( to 6 C /2.9 Viscosity range: 6 to SUS ( to mm 2 /s (recommended 6 SUS ( mm 2 /s maximum start viscosity Drive connection: Flexible coupling, for other types of drive, please consult us Installation position: Optional Direction of rotaton: Either* *Pumps may only rotate in the direction specified by model code Weights: see table for individual pump weights 8 * Displacement in /rev. (cm /rev..2 (.. (.. ( (..86 (..99 (6.2.6 (9..7 (22. Inlet pressure range (absolute p abs min. PSI (.7 bar... p abs max. PSI (. bar Max. continuous pressure P PSI (bar (2 (2 (2 (2 (2 (2 (2 (2 Peak pressure PSI (bar (27 (27 (27 ( ( ( (27 (2 Max. speed at cont. pressure P rpm 2 Min. speed at p = 26 PSI (8 bar rpm 7 Min. speed at P rpm * size - special order, only on request Operating curves, measured at ν = 9 SUS ( mm 2 /s and t = 22 F ( C Flow GPM (L/min Input power HP (kw Flow relative to drive speed (6. 22 ( ( ( (2 ( Speed (rpm p = 29 PSI ( 2 bar p = PSI (2 bar 9 6 * 8 Pemissible torque on drive shaft = Splined shaft SE- /8" T = 8 lb-ft ( Nm C = Tapered shaft : Ø 7 mm T = lb-ft ( Nm N = Tongue end shaft with coupling T = lb-ft (7 Nm S = Tapered shaft : Ø 2 mm T = lb-ft (7 Nm with additional front bearing * -special order, only on request Torque produced relative to load (9 ( (7 Drive power requirements ( p Drive power requirements ( 2 PSI (bar 2 (8 62 (2 (8 ( (2 ( ( 6 ( ( 6 ( ( ( (2 2 Torque lb-ft (Nm Input power HP (kw (6 ( ( ( (2 ( 2 ( ( * 8 ( ( (2 (2 Pressure PSI (bar 62 (2 p PSI (bar 29 (2 27 ( ( 72 ( 2 7 Speed (rpm 2 7 Speed (rpm
4 /2.9 Operating curves, measured at ν = 9 SUS ( mm 2 /s and t = 22 F ( C Charts define torque produced as a result of load pressure and drive speed. Input power HP (kw (2 ( ( ( p PSI (bar 62 (2 29 (2 27 ( ( 72 ( 7 ( 2 7 Speed (rpm Input power HP (kw (2 ( ( ( Speed (rpm p PSI (bar 62 (2 29 (2 27 ( ( 72 ( 7 ( Input power HP (kw (2 ( ( ( 2 2 *Special order, only on request p PSI (bar 62 (2 * 29 (2 27 ( ( 72 ( 7 ( 2 7 Speed (rpm Input power HP (kw (2 ( ( ( (2 p PSI (bar 6 29 (2 27 ( ( 72 ( 7 ( 2 7 Speed (rpm Input power HP (kw (2 (2 ( ( ( p PSI (bar 8 (2 ( (2 ( ( 2 ( 2 ( ( 72 ( ( Input power HP (kw 22 p PSI (bar (2 29 (2 27 ( ( 72 ( 2 7 Speed (rpm Speed (rpm
5 Noise level, measured at n = rpm, ν = 9 SUS ( mm 2 /s and t = 22 F ( C 8 (* PSI ( bar 72 ( ( ( ( ( ( * special order, only on request Shaft ends: dimensions in inches (millimeters C Tapered shaft :, Ø.669 (7 mm ( -.2 M2 x. mm.7 (.8 : Ø.669 (7 * Note: Noise level is dependant on pump speed measured in an anechoic chamber to DIN 6, distance of microphone to pump =.28 ft (m /8" SE- splined shaft, 9T 6/2 DP and tooth thickness + t = ( (.9 (2.6 (6 /2.9.2 (.669 (7 Ø.69 (.6 Ø.689 (7. This dimension is dependent upon the flange, (see page 6 * Typical Stock S Tapered shaft :, Ø.787 (2 mm for extra front bearing N Tongued shaft with coupling for center and rear pumps.7 +. ( h7 M x. mm.6 (..7 (.9 :.787 (2 Ø.787 (2.7 (9..±. (±. Ø.2 ( (.2 +. Ø (2 f (2 Ø (7. -. Ø.26 (2 Ø.7 (7.8 X.28 ( (8 d9 "X".772 ( 2 2 O-ing and coupling included in supply.8±.8 (± (6. +.2
6 /2.9 Shaft: dimensions in inches (millimeters Cylindric shaft ISO Ø 8 mm.2. (6..2 (.87 (22.8 (2. Ø.7 ±. (Ø8 ±.9. (28.2 (6 Shaft end: dimensions in inches (millimeters PF 2 G2-X/... L M (see table Clockwise = Keyed shaft Ø 8 mm Dimensions Ordering code in inches (mm Weight counterlbs (kg L clockwise clockwise.6 (88.66 ( ( (9.6 ( ( (99.78 ( ( (98.86 ( (. 6.2 (8.9 ( ( (8 2.9 ( (.. (.29 (7.2 L.6 (.. (9 2.8 (72. ±. (9 ±. Ø.. (Ø (.. (2..9 (.6 (8. ±.6 (8 ±. 6 counter-clockwise (model "L" viewed from end of drive shaft. For clockwise rotation (model "" the pressure and suction ports are opposite! Suction side Pressure side Keyed shaft Ø 8 mm
7 Unit dimensions and ordering code: dimensions in inches (millimeters /2.9 PF 2 G2-X/... L C 2 M (see table Clockwise =.28 (7.2.2 (.x Ø (Ø Tapered shaft : ; Ø 7 mm. ( 9. (2..97 (.8 (.. (9 2.8 (72 Dimensions in inches (mm Weight lbs (kg. (87.9 (.. (2.. (87.9 (.. ( (9.7 (.2.7 (2.6.8 ( (7..9 ( (.87 (7. 6. ( (.9 ( (. 22 ( 2.9 (. 7. (..±. (9±..7 (..6 (8.6 ( ( (8.7 (.787 (2*.7±.6 (8±. * Ø ( dia. in sizes and counter-clockwise (model "L" viewed from end of drive shaft. For clockwise rotation (model "" the pressure and suction ports are opposite! Suction side Pressure side.78 (.9 ( Taper : ; Ø 7 mm (see page PF 2 G2-X/... L C 2 KP (see table Clockwise =.28 (7.2.2 (.x Ø (Ø -. Tapered shaft : ; Ø 7 mm. ( ±.9 (6±.. (..±.6 (8±. 2.62±.9 (6±. Dimensions in inches (mm Weight lbs (kg. (8.2 (8..9 (2.7. (8.2 (8..9 ( (88..6 (.7 6. (2.8.7 (9.77 ( 6.6 (. 6.9 (99.7 (. 6.6 (. 9.9 (.87 (7. 7. ( ( 2.9 ( 7.7 (. Suction side Pressure side. (.6 (6.2 Taper : ; Ø 7 mm (see page ( (..7 (.787 (2* * Ø ( dia. in sizes and counter-clockwise (model "L" viewed from end of drive shaft. For clockwise rotation (model "" the pressure and suction ports are opposite!.8 ( Ø. -.9 (Ø -. (M.9 M = lb-ft (6 Nm.78 ( M = Mounting olt Torque in lb-ft (Nm.9 ( 7
8 /2.9 Unit dimensions and ordering code: dimensions in inches (millimeters PF 2 G2-X/... L 2 M (see table For SE threaded ports see page 2. Clockwise =.2 (6. (x +.2 Ø.2 -. (Ø 82. h8. (9 Splined shaft /8" SE- 9 teeth. (2.. (.. (.9 (6. Dimensions Weight in inches (mm lbs (kg.8 (9.7 (..7 (2.6.8 (9.7 (..7 ( (9..8 (.7 6. ( (98.89 (8 6. ( ( 2. (. 6.8 ( (9 2. (. 7. ( ( (8 7. (..87 (7..7 (6 Suction side Pressure side.6 (6.2 Splined shaft (see page 8 * Ø ( dia. in sizes and Envelope dimensions for this model pump correspond to PF2G2-X/ 2M, however, with port code 2 (See page 2 counter-clockwise (model "L" viewed from end of drive shaft. For clockwise rotation (model "" the pressure and suction ports are opposite! PF 2 G2-X/... L N 2 MM (see table Clockwise =, 6.28 (7.2 Ø (Ø 2 f7.7 ( Tapered shaft : ; Ø 7 mm.7 (.787 (2*. ( (2* 2.62±.9 (6±.. (. * Ø ( dia. in sizes and counter-clockwise (model "L" viewed from end of drive shaft For clockwise rotation (model "" the pressure and suction ports are opposite! Warning: In sizes 9 and 22, the pressure is reduced due to torque limitation (see page. M = Mounting olt Torque in lb.ft (Nm.7±. (8±..7±.69 (8±..8 ( 2.62±.9 (6±. Dimensions Weight in inches (mm lbs (kg. (8.8 (7..7 (2.6. (8.2 (8..7 ( (88..6 (.7.9 (2.7.7 (9.77 ( 6.6 (. 6.9 (99.79 (. 6.6 (. 9.6 (.8 ( (. 22. ( 2.9 ( 7.7 (.. ( Ø. -.9 (Ø -. (M.9 M = lb-ft (6 Nm.6 ( (.78 (.9 (.9 ( Suction side Pressure side Tongued shaft with coupling (see page 6 Pump without shaft seal
9 Unit dimensions and ordering code: dimensions in inches (millimeters /2.9 PF 2 G2-X/... L S 2 M (see table Clockwise = Tapered shaft : ; Ø 7 mm Pump with additional front bearing to support radial and axial forces (see below Dimensions Weight in inches (mm lbs (kg.7 (6 2.7 ( (..6 ( (7. 7. (. 8.7 ( ( (.. (27. (77 8. ( (. ( ( (.9 ( ( (. (8 9. ( (8 +.. (..2 (.x. (9 2.8 (72.7±.2 (9.±. Ø (Ø 8.6 (6.2. (2..97 (.8 (..7 (..6 (8.7 (.787 (2*.882±.9 (8±..78 (.9 ( * Ø ( dia. in sizes and counter-clockwise (model "L" viewed from end of drive shaft For clockwise rotation (model "" the pressure and suction ports are opposite! Warning: In sizes 9 and 22, the pressure is reduced due to torque limitation (see page. Suction side Pressure side Taper : ; Ø 2 mm (see page Extra front bearing, life calculations P dyn (kn b F F a = b =.77 in ( mm b =.6 in (7 mm b =.8 in ( mm b =.9 in (2 mm b =.79 in (2 mm L h = 6 n 6 ( C dyn F' dyn n = Speed in rpm L h = Theoretical bearing life in hours F dyn ' = Equivalent dynamic radial load C dyn = Dynamic load factor, 2.2 kn adial force F (kn 9
10 /2.9 Tandem Gear Pump Model G2 + G2, Series X Pump I Pump II Example: PF 2 G2-X/8 C 2 MK + PF 2 G2-X/ LN 2 MDL Technical data (for operation outside these parameters, please consult us! The data for single pumps is also applicable to tandem pumps (see page For tandem pumps, please note the following: Pump size may not be a front pump Pump I should consume greater power (pressure x volume than pump 2 Individual pumps are separated by a shaft seal and may draw from separate tanks The torque transmitted by the drive shafts and the coupling is limited as below When designing multiple pump assemblies, the sum of the permissible torques must not be exceeded Weights: see table for individual pumps. The parts to complete the combination weigh.9 lbs (+. kg Torque lb-ft (Nm (9 (8 (7 (6 ( ( ( (2 ( * 8 Permissible torque on the drive shaft: = Splined shaft SE- /8" T = 8 lb-ft ( Nm C = Tapered shaft : Ø 7 mm T = lb-ft ( Nm Coupling between pump and 2 T = lb-ft (7 Nm * - special order, only on request 2 2 ( 62 ( ( (2 (2 Pressure PSI (bar
11 Unit dimensions and ordering code: dimensions in inches (millimeters PF 2 G2-X/... C 2 MK L L PF 2 G2-X/... N 2 MDL (see table Clockwise = Pumps I & II must be opposite rotation..28 (7.2.2 (.x. ( I D Dimension Weight in lbs (kg C D MK MDL.8 (88..6 (2 6.8 (..7 ( (8..9 (..8 (88..6 (2 7 (.2.7 ( (87..7 (.2.8 (9.7 ( (..9 (2.7.7 (9.87 (7..76 (9..79 (. 7.7 (. 6.6 (. 6.8 ( (7.. (2..9 (9 7.9 ( (. 9. (..9 (9..9 (6. 2. ( 7.9 ( ( ( 2.9 (.. (. 2.9 (. 8.8 (. 7.7 (. C II max..2 (6.8 (.. (9 2.8 (72.±. (9±. /2.9 Ø (Ø 8.6 ( (.7 ( ( (8. ( (2* (2*.7.7 * Ø ( dia. in sizes and ( ( counter-clockwise (model "L" viewed from end of drive shaft For clockwise rotation (model "" the pressure and suction ports are opposite! Warning: In sizes 9 and 2, the pressure is reduced due to torque limitation (see page..7±.6 (8±..6 (6.2.6 (8.78 (.9 ( Suction side Pressure side (the same for both pumps when assembled Taper : ; Ø 7 (see page PF 2 G2-X/... C 2 MPK L L PF 2 G2-X/... N 2 MDL (see table Clockwise = Pumps I & II must be opposite rotation..28 (7.2.2 (.x Ø (Ø -. I Dimension Weight in lbs (kg C D MK MDL.8 (88..6 (2.9 (2.7.7 (2.6.2 (8..2 (8..8 (88..6 (2.9 (2.7.7 ( (8.6 (.7.8 (9.7 (.2 6. (2.8.9 (2.7.6 (9..77 (.87 (9..79 (. 6.6 (. 6.6 ( (9..7 (.. (2..9 (9 6.6 (. 6.6 ( ( (7..9 (6. 2. ( 7. ( ( (. 2.9 (. (. 2.9 (. 7.7 (. 7.7 (. C max..2 (6 D.8.9 II (.7 ( (.. ( ( (..7 (.787 (2*.7 ( * Ø ( dia. in sizes and counter-clockwise (model "L" viewed from end of drive shaft For clockwise rotation (model "" the pressure and suction ports are opposite! M = Mounting olt Torque in lb.ft (Nm.6 (6.2.6 (6.2.9 (.787 (2* 2.62±. (6±. (M.9 M = lb-ft (6 Nm 2.62±. (6±..7±.6 (8±. Ø. -. (Ø ( Suction side Pressure side (the same for both pumps when assembled Taper : ; Ø 7 (see page
12 /2.9 Unit dimensions and ordering code: dimensions in inches (millimeters (see table Clockwise = 2 PF 2 G2-X/... 2 MK L L PF 2 G2-X/... N 2 MDL Pumps I & II must be opposite rotation. * Ø ( dia. in sizes and Envelope dimensions for this model pump correspond to those for combination type PF2G2-X/ 2MK + PF2G2-X/, however, with port code 2 (see page 7. counter-clockwise (model "L" viewed from end of drive shaft For clockwise rotation (model "" the pressure and suction ports are opposite! PF 2 G2-X/... C 2 MK PF 2 G2-X/... LN 2 MDN PF 2 G2-X/... LN 2 MDL (see table Clockwise = Note: Pumps II & III are ordered opposite rotation as pump I (porting appears on the same side of all three pumps when assembled..28 (7.2.2 (.x Ø (Ø (6. (x Ø (Ø82. h ( (8.787 (2* * Ø ( dia. in sizes and Dimension Weight in lbs (kg C D KK MDL.8 (88..6 (2.7 (2.6.7 (2.6. (87..7 (..8 (88..6 (2.7 (2.6.7 ( (9.8 (.7.8 (9.7 (.2 6. (2.8.9 ( (9..88 (8.76 (9..79 (. 6. ( (. 6 (. 2. (.. (2..9 (9 6.8 (. 6.6 (. 9. (. 2. (..9 (6. 2. ( 7. ( ( ( (8. (. 2.9 (. 7.2 (. 7.7 (. Suction side Pressure side (the same for both pumps when assembled Taper : ; Ø 7 (see page Weight in Dimension lbs (kg E F C D MDN.8 (88..6 (2.29 (8..9 (.. (8.6 (2.8 (88..6 (2.7 ( (87..7 (.2.8 (9.7 (.2.7 (9.87 (7..62 (92.79 (..76 (9..79 (. 6.6 (. 6.8 ( (7..9 (99.9 (9. (2..9 (9 6.6 (. 9 (..9 (9..9 (6. 2. ( 22.9 ( 2.9 (..9 ( 2.9 (.. (. 2.9 (. 7.7 (. E C F D. ( I II III.78 ( I. (9.7 (.9 ( D.78 ( II C.7 (.9 (.787 (2*.6 ( ( max..2 (6. (.. (2..6 ( (. (2..9 (. (.9 (6..7±.6 (8±. max..2 (6.8 (. Suction side Pressure side. (9 2.8 (72.87 (7..7±.6 (8±..6 (6.2.6 (6.±. (9±..6.7 (6.2 (..6 (8.787 (2* xm6/.7 ( (the same for both pumps when assembled Splined shaft (see page.78 (.9 (
13 Unit dimensions and ordering code: dimensions in inches (millimeters /2.9 PF 2 G2-X/... 2 MK PF 2 G2-X/... LN 2 MDN PF 2 G2-X/... LN 2 MDL (see table Clockwise = Note: Pumps II & III are ordered opposite rotation as pump I (porting appears on the same side of all three pumps when assembled. E.2 (6. (x Ø (Ø (9 * Ø ( dia. for sizes and.78 ( Weight in Dimension lbs (kg E F C D MDN.8 (88..6 (2. (87..7 (.. (8.6 (2.8 (88..6 (2.7 ( (9.8 (.7.8 (9.7 (.2.72 (9..88 (8.62 (92.79 (..76 (9..79 (. 6.6 (. 6 (. 2. (..9 (99.9 (9. (2..9 (9 6.6 (. 9. (. 2. (..9 (6. 2. ( 22.9 ( (8.9 ( 2.9 (.. (. 2.9 (. 7.7 (. F I II III.9 (.78 ( D.9 ( C.78 (.9 ( max..2 (6. (..6 (6.2. (2. Envelope dimensions for this model pump correspond to those for combination type PF2G2-X/ 2MK + PF2G2-X/, however, with port code 2 (see page 7. Seal kits (una-n. (.9 (6..7±.6 (8±..87 (7..6 (6.2. (6.7 (.787 (2* Suction side Pressure side (the same for three pumps when assembled Splined shaft (see page Pump type Part No. Part No. (all sizes Seal kit Shaft seal PF 2 G2-X/...C 2 M 9 8 PF 2 G2-X/...C 2 KP 9 2 (FPM PF 2 G2-X/... 2 M 9 8 PF 2 G2-X/...S 2 M PF 2 G2-X/...N 2 MM 9 Pump type Part No. Part No. (all sizes Seal kit Shaft seal PF 2 G2-X/...C 2 MK 9 8 PF 2 G2-X/...C 2 KPK 9 2 (FPM PF 2 G2-X/... 2 MK 9 8 PF 2 G2-X/...N 2 MDL 9 8 PF 2 G2-X/...N 2 MDN 9 8 Flanged fittings for pipe connections, Code 2 Straight flanged fitting ight angle flanged fitting Suction side Pressure side Pipe dia. Ordering Code Pipe dia. Ordering code Suction side Pressure side Pipe dia. Ordering Code Pipe dia. Ordering code ll fittings are supplied complete with fixing screws, O-ing, cutting ring and retaining nut
14 /2.9 Notes: Mannesmann exroth Corporation exroth Hydraulics Div., Industrial, 2 City Line oad, ethlehem, P 87-2 Tel. ( Fax: ( exroth Hydraulics Div., Mobile, 7 Old Mansfield oad, Wooster, OH 69-9 Tel. ( 26- Fax: ( 26- ll rights reserved - Subject to revision Printed in U.S..
Vane Pump Series SDV. Fixed Displacement zp14. Catalogue HY0738-A/CH November Hydraulics. Hydraulics
SDV Fixed Displacement zp4 Catalogue HY078-/CH November 004 Contents SDV Introduction General applications instructions... Maximum speed... Pressure ratings... Minimum allowable inlet pressure... General
More informationVickers Service Data Vane Pumps ThruĆDrive Vane Type Pump (F3)-45VT*(M)-**A(M)2-**-*-22 Rev 2/98 I-3151-S
Vickers Vane Pumps MODEL VTA VTB VTBP VTC ADAPTER PLATE 584936 584922 ADAPTER 941296 941297 581833 941298 FOR BP MODELS AN ADAPTER AND SPACER IS REQUIRED. SPACER 02-136817 RETAINING COUPLING COUPLING RING
More informationVickers Service Data Vane Pumps Thru-Drive Vane Type Pump (F3)-35VT*(M)-**A(M)2-**-*-22-* Revised 2/98 I-3149-S
Vickers Vane Pumps MODEL VTA VTB VTBP VTC ADAPTER PLATE 584936 584922 ADAPTER 941296 941297 581833 941298 FOR BP MODELS AN ADAPTER AND SPACER IS REQUIRED. SPACER 02-136817 RETAINING COUPLING COUPLING RING
More information"PVL" SERIES. Fixed Displacement - Single PVL1. Up to 5 MPa (730 PSI), 10.6 cm /rev (.647 CU.IN./rev)
"PVL" SERIES Fixed Displacement - Single PVL Up to 5 (70 ), cm /rev (7 CU.IN./rev) Pub. EC-0 The PVL series single pumps are designed for use with small size machine tools requiring comparatively low pressure
More informationTPV 1200 BTB. Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump THE PRODUCTION LINE OF HANSA-TMP HT 16 / M / 156 / 1214 / E
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS GEARBOXES - ACCESSORIES THE PRODUCTION LINE OF HANSA-TMP Variable Displacement Closed Loop System Axial Piston Compact Tandem Pump CONTENTS General Information...
More informationProportional electrohydraulic controls for PVPC pumps pressure-flow combined P/Q controls, analog or digital
www.atos.com Table A70/E Proportional electrohydraulic controls for PVPC pumps pressureflow combined P/Q controls, analog or digital The variable displacement axial piston pumps type PVPC, can be supplied
More informationRadial Piston Hydraulic Motor with Fixed Displacement MR, MRE
+ (0)0 69999 Radial Piston Hydraulic Motor with Fixed Displacement MR, MRE RE 8 Issue: 08.0 Replaces: 08.008 Sizes to 00 Nominal pressure 0 bar Maximum pressure up to 00 bar Displacement up to 090 cm orque
More informationRadial Piston Hydraulic Motor with Fixed Displacement MR, MRE
Radial Piston Hydraulic Motor with Fixed Displacement MR, MRE RE 8 Issue: 09.0 Replaces: 08.0 Sizes to 00 Nominal pressure 0 bar Maximum pressure up to 00 bar Displacement up to 090 cm orque up to 800
More information1 - "F3" means special seals for fire-resistant fluids. Omit if not required
V* DOUBLE VANE PUMPS ORDERING CODE 1 - "F3" means special seals for fire-resistant fluids. Omit if not required - Pump Type: F3 VS 3 1 D 1 A A 1 3 7 VC = 1 vane pump, medium pressure application. VS =
More informationStainless Steel Submersible Pumps DATA BOOKLET. ISO 9001 Company. 60 Hz. Pumping Solution
Stainless Steel Submersible Pumps DATA BOOKET ISO Company Pumping Solution Hz Photographs of a few Manufacturing Units Contents Stainless steel submersible bore well pumps Product data Introduction Operating
More informationCompact Bellows Pumps
Compact Bellows Pumps Compact Bellows Metering Pumps were specifically designed for metering applications requiring low discharge pressures. Compact pumps have been successfully applied in photo, X-ray
More informationMechanical accessories
Bearing box Part no. 01209010, 01209029 Part no. 01209010 01209029 Shaft size Ø 15 mm Ø 10 mm Shaft load max Radial: 250 N, Axial: 150 N Speed max 4000 rpm Protection class IP 64 according to IEC 60529
More informationParts / Spares Reference Sheet
Parts / Spares Reference Sheet Graco GMAX 5900 GMAX II 5900/5900HD Standard Series GMAX II 5900/5900HD Standard Series 0 28 22 30 2 5 38 4 46 6 37 50 9 45 2 20 45 43 8 0 52 05 23 40 27 38 5 3 32 33a 33b
More informationF3 BHQ 4 67 D 1 A
BH*SINGLE VANE PUMP ORDERING CODE F3 BHQ 4 67 D 1 A 00 1 3 4 5 6 7 8 1- F3 means special seals for fire-resistant fluids. Omit if not required. - Pump Type: BHP = vane pump, industrial and mobile use,
More informationL P Linn-Pumpen GmbH. Electric-gear-pumps series FKM
Electric-gear-pumps series FKM Construction Self-priming electric-gear-pumps, bellhousing with foot-flange, pump-casing in cast iron. Gear-pumps series FKM with motor-power up to 1,5. Suction- and -ports
More informationSUCTION FILTERS. PRESSURE (ISO :2002) Collapse, differential for the fi lter element (ISO 2941): 1 MPa (10 bar)
COMPONENTS SUCTION ILTERS SD MATERIALS Cover & housing: Anodized aluminium alloy or 6&6 only: Cover: anodized aluminium alloy Housing: steel ypass valve: Polyammide Seals: NR Nitrile (KM on request fl
More informationCLAMSHELL PIPE CUTTING AND BEVELLING MACHINES. Mactech Europe LTD
CLAMSHELL PIPE CUTTING AND BEVELLING MACHINES Mactech Europe LTD Mactech s Clamshell lathes are portable pipe cutting machines designed for on-site precision severing, severing/beveling, and severing/double
More informationVariable Displacement Vane Pumps
Variable Displacement Vane Pumps Service Parts Manual VVS0 VVS1 VVS2 VVS3 VVP1 VVP2 VVP3 Available Spares Shaft Keys PUMP PART DIMENSIONS NUMBER VVS0-R 02-352334 6x6x25 VV*1-R 02-352335 8x7x25 VV*2-R,
More informationJVMG* *NSF 61/Annex G Certification and Compliance with State Codes does not apply to JVMG Models
JVM, JVML SERIES Stainless Steel Construction Closed multi-stage impeller Flow: 4 to 38 GPM Head: to 82 ft. Range of HP: to HP Applications: Commercial booster system, Boiler feed, Jockey, Water Purification,
More informationClose-coupled centrifugal pumps
CombiBloc Close-coupled centrifugal pumps CombiBloc CombiBloc is the premier solution for pumping clean thin liquids in a very cost-effective way. The pump is part of Johnson Pump s Combi-system, a modular
More informationRotary Ball Spline. With Support Bearing Type Models LTR and LTR-A
With Support Bearing Type Models LTR and LTR-A Outer ring Ball Flange outer ring Seal Seal Retainer Spline nut Spacer Retainer Spline shaft Fig.1 Structure of Model LTR Point of Selection Point of Design
More informationL P Linn-Pumpen GmbH. Submersible Vertical Electric pumps. SVI Series. with high efficiency PLM motors. SVI Series MARKET SECTORS INDUSTRIAL, CIVIL.
Submersible Vertical Electric pumps with high efficiency PLM motors MARKET SECTORS INDUSTRIAL, CIVIL. APPLICATIONS Pumping of coolants, lubrificants and condensate. Machine tools, welders, engine test
More informationFEATURES APPLICATIONS OPERATING DATA MATERIALS OF CONSTRUCTION. Flood control
APPLICATIONS FEATURES Flood control Irrigation Land drainage Pollution control Industry Water refineries Water parks Design OPERATING DATA Capacity:...up to.000 m/h Head:...up to m Max. water temperature:...0
More informationCompliance with API Standard 670 the PRO Product Standard for Proximity Probes
Connection Technology Center, Inc. 7939 Rae Boulevard Victor, New York 14564 Toll Free: (800) 999-5290 Phone: (585) 924-5900 Fax: (585) 924-4680 Compliance with API Standard 670 the PRO Product Standard
More informationSolutions. ydraulics. We Manufacture. H y d r a u l i c s. h y d r a u l i c s. Hydraulics Division Eaton / Char-Lynn Hydraulic Products
H y d r a u l i c s ydraulics Hydraulics Division Eaton / Char-Lynn Hydraulic Products h y d r a u l i c s We Manufacture No. 11-895 January 1999 Solutions S o l u t i o n 1 s Experienced system design
More informationBARE SHAFT PUMPS AND MOTOR PUMPS
APPLICATIONS Air Conditioning Heating and ventilation Refrigeration Fire protection Plumbing Water Circulation Transfer and Irrigation Pressure Boosting Process Industries Water Treatment and Supply DESIGN
More informationDX300LCA SLR. Construction Equipment. Engine Power Operational Weight Bucket / PCSA
Construction Equipment DX300LCA SLR Engine Power Operational Weight Bucket / PCSA SAE J1349, net 147kW (197HP) @ 1,900rpm 30,900kg 0.64m 3 (0.83cu.yd) DIMENSIONS A D E H J F P O B C G I K L M N Dimensions
More informationThis is trial version
s, s, Ejector coupling devices, Unscrewing components, Two-stage ejectors, Latch locking units, Mould slides-modular system 2.01 2.02 Ordering example : Z 40 / 1,6 x 40 Shaft Overall length Z02/... 2.1
More informationSYSTEMS ELECTRONICS GROUP
SYSTEMS ELECTRONICS GROUP SYSTEMS M4500 MACHINE COMPONENTS RSV34-MS1 RESOLVER with MS CONNECTOR Brushless, Single-turn Resolver Rated to 3,000 RPM Rotary Position Transducer for M4500, M4020, M4040, M4041,
More informationLH 700. Spare parts list. Forward and reversible plate. Valid from serial number. LH 700 Hatz Electric start 810 mm Bio
LH 00 Spare parts list Forward and reversible plate LH 00 Hatz Electric start 0 mm LH 00 Hatz Electric start 0 mm Bio LH 00 Hatz Electric start 0 mm LH 00 Hatz Electric start 0 mm Bio Valid from serial
More informationT2 B Series. Compact Height Nitrogen Gas Springs
T2 B Series Compact Height Nitrogen Gas Springs ife in excess of 100,000 stroke meters. Cartridge design for easy maintenance. Oil pipe prevents oil leaving the springs in a hosed system and helps maintain
More informationLenntech BMP GRUNDFOS DATA BOOKLET. High-pressure piston pumps 50/60 Hz
Lenntech GRUNDFOS DATA BOOKLET BMP High-pressure piston pumps 50/60 Hz Contents Product data Introduction Page 3 Features and benefits Page 3 Applications Page 3 Pumped liquids Page 3 key Page 4 Motor
More informationIncremental Encoder with Hollow Shaft
Incremental Encoder Type RI 36-H n miniature industry encoder for high number of pulses n short mounting length n easy mounting procedure n Application e.g.: - Motors - Machine tools - Packaging Machines
More informationScrew-Type Flow Meter SVC
Screw-Type Flow Meter SVC Description Screw-type flow meters belong to the group of positive displacement flow meters. Two measuring spindles (pos. 2) with a screw-shaped profile engage with each other.
More informationSIZES FROM 1, ,000 Nm BACKLASH FREE, TORSIONALLY STIFF METALLIC BELLOWS COUPLINGS
BX ZA SIZES FROM 1,500-100,000 Nm BAKLASH FREE, TORSIONALLY STIFF METALLI BELLOWS OUPLINGS BELLOWS OUPLINGS BX ZA Optional: GENERAL INFORMATION ABOUT R+W BELLOWS OUPLINGS: SERVIE LIFE R+W bellows couplings
More informationParts and Service Manual IMCO
XXTREME ADVANTAGE Gimbal Parts and Service Manual IMCO 510 East Arrow Highway San Dimas, CA 91773 (800) 899-8058 (909) 592-6162 Fax (909) 592-6052 www.imcomarine.com email info@imcomarine.com TABLE OF
More informationLH 700. Spare parts list. Forward and reversible plate. Valid from serial number. LH 700 Hatz Electric start 810 mm Bio
Forward and reversible plate Hatz Electric start 0 mm Hatz Electric start 0 mm Bio Hatz Electric start mm Bio Valid from serial number 0000 0000 0000 Contents Contents General information.....................................................................................................................................
More informationValve adapters Hägglunds VA 1000
Valve adapters Hägglunds VA 1000 RE 15383 Edition: 12.2015 Replaces: New Valid for Hägglunds motors CA, CB, CBM Maximum flow 1000 l/min (264 gpm) Maximum pressure 350 bar (5076 psi) Example: Adapter Features
More informationUNIFLEX TRIPLE SPRING COUPLING
Specialty Couplings Overview Uniflex Coupling Design Flexible Spring Type Coupling with Exclusive Triple Wound Spring Design The Uniflex Coupling is an all steel, single piece coupling that solves a variety
More informationHigh Torque Type Ball Spline
58-1E Models LBS, LBST, LBF, LBR and LBH Seal Spline shaft Spline nut Ball Retainer Snap ring Fig.1 Structure of Model LBS Point of Selection Point of Design Options Precautions on Use Accessories for
More information50 years of Reliable Field History
COUPLING COMMENTS The No Maintenance, Easy Assembly, Resilient Coupling with High Angular Misalignment up to 0 degrees Center Assembly 70 Deg. Neoprene Rubber in Compression Grade 5 Bolts Steel Flanges
More informationVariable Stroke Straight-Line Action
4. FO Series FL Series G Series Type of Mounting: Type of Actuation: Hand wheel or hand lever (one-handed operation) Locking lever and (two-handed operation) Type of Mounting: Type of Actuation: Locking
More informationContents. Directional Control Valve 2 Series EPCV 452. Page 3. General Information. Page 4-5. Technical data. Page 6. Performance Curves.
Contents Page 3 Page 4-5 Page 6 Page 7 Page 8 Page 9 Page 10 General Information Technical data Performance Curves Dimensions : Hydraulic Valve and Accumulator Hydraulic Schematics Dimensions : Electrical
More informationStandard Cartridge Valves 2/2 Way Series NG16 NG100
Standard Cartridge Valves Way Series NG NG Table of Contents Designation Symbol Page General Description and Operating Principle Specifications and Characteristic Parameters Typical Characteristic Curves
More informationStandard Circulating Pumps
Product review Range: 1 1 3Q [ m³/h] Hz - North America 1 3 1 1 1.x1 1.x x x3 x 1 1 Q [ US gpm] >Single-head pumps: Seal-less circulator with flanged connection. Two speed, manually adjustable to match
More informationAsynchronous motors. 5/48 Permissible combinations of mechanical designs for 1PL6 motors,
Asynchronous motors 5 Asynchronous motors 5/2 Type overview and rated data 5/4 Technical definitions 5/4 Encoder systems 5/5 1PH7 motors 5/5 1PH7 motors, forced ventilation 5/32 Permissible combinations
More informationDIP. Spare parts list. Centrifugal pumps 25, 25-US, 35, 35-US, 65, 65-US Atlas Copco Construction Tools AB No c
DIP 5, 5US, 35, 35US, 65, 65US Spare parts list Centrifugal pumps 0 Atlas Copco Construction Tools AB No. 9800 5 0c 003 DIP 5, 5US, 35, 35US, 65, 65US Contents Contents General information................................................................
More informationED-21 Analog Output Series Magnetic Encoder
Analog voltage or current output Low profile IP52 sealing Ball bearing Custom housings, shafts, connectors available, in most cases with no additional tooling required DESCRIPTION The ED-21 series magnetic
More informationFluidControl Unit FCU 2010/FCU 2110
FluidControl Unit /FCU 2110 1 1. OIL CONDITION MONITORING AND OIL SERVICING 1.1. THE CONCEPT For hydraulic systems and lubrication systems to operate reliably it is imperative that the operating fluid
More informationLCC Pump Series - Wear Resistant, High Performance Slurry Pumps
LCC Pump Series - Wear Resistant, High Performance Slurry Pumps 02 LCC Pump Series Solutions for the most Abrasive and Corrosive Slurry Applications With High Performance Wear Resistance, the GIW Minerals
More informationSYMBOLS, UNITS AND DEFINITIONS
SYMBOLS, UNITS AND DEFINITIONS Values depending on the APPLICATION term u.m. definition A 2 [N] Thrust force on output shaft R 2 [N] Radial force on output shaft ED [min] Loading time ED% [%] Loading time
More informationStandard Bellows Metering Pumps
Standard Bellows Metering Pumps Bellows Metering Pumps operate on a positive displacement principle. Pumps are designed to displace both corrosive and noncorrosive fluids. Accurate to ± 0.5% from stroke
More informationTable of Contents: TOPIC: Safe Operation: READ THIS FIRST Page: 3 Warranty 4 Specifications 4 Installation 5-7 Operating Instructions 8 Parts Diagram
INSTALLATION & OPERATIONS MANUAL FlexArm B-19 FlexArm Inc. Division of Midwest Specialties, Inc. 851 Industrial Drive Wapakoneta, Ohio 45895 419-738-8147 Book Part No 360740 12/2014 1 Table of Contents:
More informationProduct Information ROC 425 ROQ 437. Absolute Rotary Encoders with EnDat 2.2 for Safety-Related Applications
Product Information ROC 425 ROQ 437 Absolute Rotary Encoders with EnDat 2.2 for Safety-Related Applications 10/2016 ROC 425, ROQ 437 with synchro flange Rotary encoders for absolute position values with
More informationProduct Information ROC 425 ROQ 437. Absolute Rotary Encoders with Solid Shaft for Safety-Related Applications
Product Information ROC 425 ROQ 437 Absolute Rotary Encoders with Solid Shaft for Safety-Related Applications 2/2016 ROC 425, ROQ 437 with synchro flange Rotary encoders for absolute position values with
More informationSECTION 8 - ULTRA & ULTRA-C PARTS CATALOGUE
SECTION 8 - ULTRA & ULTRA-C PARTS CATALOGUE PART # DESCRIPTION PAGE MOUNTING KITS & TANKS 903U MOUNTING KIT WITH TANK 801-802 905U MOUNTING KIT WITHOUT TANK 803-804 902U MOUNTING KIT - CRADLE, BLOCKS &
More informationTD End-Suction Pumps. Operating data Flow rates up to 300 l/sec Head up to 160 metres Temperature 20 0 C to C
TD End-Suction Pumps One of the broadest ranges of pumps available from any British manufacturer, with discharge sizes from mm to 0 mm. Widest choice of materials of construction and options to suit many
More informationT E M P O S O N I C S I I I INSTALLATION CAUTION! B. CONNECTORS RG Connector. D6 Connector: INTEGRAL CABLE P Integral Cable
T E M P O S O N I C S I I I INSTALLATION C A N B U S O U T P U T 550573 B W I R I N G - C A N b u s O U T P U T S CONNECTORS RG Connector Pin No. Wire Color Function 1 Gray CAN-L 2 Pink CAN-H 3 Yellow
More information8 Submersible Motors Standard
Applications These motors are built for dependable operation in vertical 8 diameter or larger water wells. Basic Features Double Flanged NEMA mounting design Stainless steel splined shaft StatorShield
More informationT2 B Series. Compact Height Nitrogen Gas Springs
T2 B Series Compact Height Nitrogen Gas Springs ife in excess of 100,000 stroke meters. Cartridge design for easy maintenance. Oil pipe prevents oil leaving the springs in a hosed system and helps maintain
More informationCOBRA. Spare parts list. Petrol drills and breakers COMBI Atlas Copco Construction Tools AB No c
COBRA COMBI Spare parts list Petrol drills and breakers 0 Atlas Copco Construction Tools AB 00 0 0c 00 COBRA COMBI Contents Contents General information................................................................
More information72 Heavy Duty Dual Trim Deck Parts Manual
2 Heavy Duty Dual Trim Deck Parts Manual Hustler Turf Equipment P.O. Box 000 Hesston, Kansas 02-209 02999 Rev 8/0 Table of Contents Chapter General Information.................................... - Chapter
More informationAbsolute encoder TBD/TRD with PROFIBUS-DP interface
with PROFIBUS-DP interface Document no.: TRD 11868 LE Date: 15.02.2016 Singleturn and multiturn versions Contactless, wear-free sensor system according to the Hall principle High vibration and shock resistance
More informationRD 100. Spare parts list. RD 100 s/n BES Construction Tools PC AB No
RD 100 Spare parts list RD 100 s/n BES100496 2018 Construction Tools PC AB No. 9800153901 2018-10 General information This spare parts list applies to the following: Part number 8311030410 RD 100 Description
More informationScrew-Type Flow Meter SVC
Screw-Type Flow Meter SVC Description Screw-type flow meters belong to the group of positive displacement flow meters. Two measuring spindles (pos. 2) with a screw-shaped profile engage with each other.
More informationBG 240. Spare parts list. Trowel. Valid from serial number Atlas Copco Construction Tools AB No c
BG 0 Spare parts list Trowel BG0 HSQP BG0 HSQP BG0 HSTP BG0 HSTP Valid from serial number BGB00000 BGB00000 BGF000000 BGF000000 0 Atlas Copco Construction Tools AB No. 900 0 0c 00 BG 0 Contents Contents
More informationYOUR COMPLETE SOURCE FOR. Gear Reducers Couplings & Linear Mount Products. Product Range. GAM Can.
YOUR COMPLETE SOURCE FOR Gear Reducers Couplings & Product Range Linear Mount Products GAM Can. YOUR COMPLETE SOURCE FOR GEAR REDUCERS, COUPLINGS & LINEAR MOUNT PRODUCTS Product Selection Guide Gear Reducers
More informationBall Spline Types LT and LF
Ball Spline Types and LF Ball Spline nut Snap ring Seal Retainer Spline shaft Fig. Construction of Ball Spline Type Construction and Features Ball Spline types and LF have four or six trains of loadbearing
More informationSpare parts list. Forward and reversible plate MV 305, Valid from serial number. MV 305 Honda 600 mm MV 320 Hatz 600 mm
Spare parts list Forward and reversible plate MV 0, 0 MV 0 Honda 00 mm MV 0 Hatz 00 mm MV 0 Honda 00 mm MV 0 Hatz 00 mm Valid from serial number 0000 0000 BGF000000 BGF000000 www.cp.com MV 0, 0 00 00 0c
More informationStandard Circulating Pumps
Product review Range: 1 1 3Q [ m³/h] Hz - North America 1 3 1 1 1.x1 1.x x x3 x 1 1 Q [ US gpm] >Single-head pumps: Circulating pumps with flanged connection > Applications: Drinking-water circulation
More informationScrew-Type Flow Meter SVC
Screw-Type Flow Meter SVC Description Screw-type flow meters belong to the group of positive displacement flow meters. Two measuring spindles (pos. 2) with a screw-shaped profile engage with each other.
More informationHow to Identify Fluid Ports and Connectors. A guide to North American, British, Japanese, German (DIN metric), and ISO connections
How to Identify Fluid Ports and Connectors A guide to North American, British, Japanese, German (DIN metric), and ISO connections How to measure threads Use a thread pitch gauge to determine the number
More informationSB 202. Spare parts list Hydraulic breakers. SB 202 s/n BES Construction Tools PC AB No
SB 202 Spare parts list Hydraulic breakers SB 202 s/n BES051618 2018 Construction Tools PC AB No. 9800172001 2018-01 General information This spare parts list applies to the following: Part number 8460030050
More informationSpare parts list. Handheld pneumatic pick hammers CP 0222 CHIT, CP 0222 CHIT BS, CP 0222 CHOT BS.
Spare parts list Handheld pneumatic pick hammers CP 0 CHIT, CP 0 CHIT, CP 0 CHOT www.cp.com CP 0 CHIT, CP 0 CHIT, CP 0 CHOT 9800 00 0 CP 0 CHIT, CP 0 CHIT, CP 0 CHOT Contents Contents General information...............................................................
More informationLevel- and temperature sensor Nivotemp NT M-XP
Level- and temperature sensor Nivotemp NT M-XP Fluidcontrol In hydraulics and lubrication technology the fill level of oil tanks needs to be monitored continuously. Here, modern factory automation requires
More informationSTANDARD CARTRIDGE VALVES 2/2-WAY
STNDRD CRTRIDGE VLVES -WY SERIES NG NG ulletin - DESIGNTION SYMOL PGE General Description and Operating Principle Specifications and Characteristic Parameters Typical Characteristic Curves - -way Cartridge
More informationOperating Instructions Wall saw WSE1217 USA
Operating Instructions Index 000 Original operating instructions 10992859 en / 25.04.2012 Congratulations! With a Hydrostress unit from TYROLIT, you have chosen a tried and tested piece of equipment which
More informationLevel- and temperature sensor Nivotemp NT 67-XP
Level- and temperature sensor Nivotemp NT 67-XP Fluidcontrol In hydraulics and lubrication technology the fill level of oil tanks needs to be monitored continuously. Here, modern factory automation requires
More informationBall Screw Actuator Models Advantages:
Ball Screw Actuator Models Advantages:! Move loads and apply force more efficiently than other mechanical actuators.! Permit faster operation and longer life under load.! Require less power by providing
More informationThe HELLE Log Turner
The HELLE Log Turner Equipment may vary from what is pictured. PARTS MANUAL HELLE Sawmill Equipment Mfg. by Sawmill Hydraulics, Inc. 1-800-245-2448 www.4helle.com 1 HYDRAULIC DRIVE MOTOR SPROCKET PART
More informationMini Bellows Pumps. 180 Hines Ave. Bellville, OH PH: FAX:
Mini Bellows Pumps Mini Bellows models are ideal for low flow, low pressure metering applications. The pump is constructed entirely of plastic and utilizes GRI s time-proven bellows technology to provide
More information8 Submersible Motors Hi-Temp 75
Applications These motors are built for dependable operation in vertical 8 diameter or larger wells, in applications with higher temperature, higher thrust or low flow. Basic Features Able to operate in
More informationGRM SERIES. Mechanical stamping and forming machines GRM 80E / GRM 80P
GRM SERIES Mechanical stamping and forming machines GRM 80E / GRM 80P More economical large-scale production Produce stamped and formed parts in large batches with even higher productivity. Benefit from
More informationSeries description: Wilo-MultiCargo HMC
Series description: -MultiCargo HMC H/m HMC 5 HMC -MultiCargo HMC 3../.. 1 3 5 7 /m³/h Design Self-priming water-supply unit Application Water supply Sprinkling Irrigation and spraying Pumping water from
More informationOPERATING INSTRUCTIONS WCU17
OPERATING INSTRUCTIONS Index 000 Translation of the original instructions 10999826 en / 05.10.2018 Congratulations! You have decided to purchase a tried-and-tested TYROLIT Hydrostress unit and have thus
More informationT E M P O S O N I C S I I I INSTALLATION
T E M P O S O N I C S I I I INSTALLATION A N A L O G O U T P U T W I R I N G - A N A L O G O U T P U T S 550572 B CONNECTORS RG Connector: Pin No. Wire Color Function 1 Gray Output #1 (Displacement) *
More informationLCD 500,1500. Spare parts list. Handheld core drills. Valid from serial number Construction Tools PC AB No
LCD 500,1500 Spare parts list Handheld core drills LCD 500 LCD 500 LCD 1500 Valid from serial number BGF0006875 BGF0006875 BGF0006875 2015 Construction Tools PC AB No. 3392 5193 01 2015-06 General information
More informationbidirectionally as well as the rotation sense of shafts. With absolute encoders instead, each incremental
and draw-wire sensors Spot-on and trailblazing technology measure rotation speed, sense, position, angle and length. For this purpose, they convert mechanical motion in electrical signals. There are incremental
More informationSubmersible Pumps. Pumping Solution. 50 Hz
Submersible Pumps Pumping Solution 0 Hz INTRODUCTION Submersible bore well pumps for (DN 0 mm), (DN 0 mm), (DN 0 mm), (DN 00mm), (DN 0 mm) and (DN 00 mm) wells. Sized for connection to the motor according
More informationPUMPS FOR INDUSTRY. The Vertical Pump Specialists CONTENTS: Introduction & User List. Product Overview. Vertical Process Pumps...
PUMPS FOR INDUSTRY CONTENTS: The Vertical Pump Specialists Introduction & User List Product Overview Vertical Process Pumps... Vertical Sewage Pumps... Series 700 Vertical Sump Pumps... Series 800 Vertical
More informationPIONJÄR. Spare parts list. Petrol drills and breakers 120, 120 AV, 121 A, 130, 130 AV, 131 A
PIONJÄR 0, 0 AV, A, 0, 0 AV, A Spare parts list Petrol drills and breakers 0 Atlas Copco Construction Tools AB 00 00 0b 00 PIONJÄR 0, 0 AV, A, 0, 0 AV, A Contents Contents General Information................................................................
More informationENCODER. Profibus Multiturn. Series , Key-Features:
ENCODER Profibus Multiturn Series 8.5868, 8.5888 Key-Features: Content: Order Code Technical Data Profibus Interface Connection Technical Drawing......3...4...4...5 - Solid shaft: maximum diameter 0 mm
More informationMembers: Sponsor: Dalton Hamilton Preston-Eastin Levi Edens Kenneth Mui Brice Abbott
Members: Dalton Hamilton Levi Edens Brice Abbott Sponsor: Preston-Eastin Kenneth Mui Mission Statement Wolf Pack Engineering strives to provide our customer with innovative solutions. We take a cost effective
More informationMAX FLUID TEMPERATURE
Centrifugal pumps are designed to transfer both corrosive and non-corrosive fluids at maximum hydraulic efficiencies. Centrifugal pumps are not self-priming and must be used in applications where flooded
More informationDescription: Detailed procedure on removing old bushing and installing new Brake Bushing Replacement Kit 10447
Procedure: BRAKE BUSHING REPLACEMENT PROCEDURE Product: Document #: Rev: Page: MODEL 7000, 7000A, & 8000 GYRO 078 1 1 of 14 Description: Detailed procedure on removing old bushing and installing new Brake
More informationFlexible claw couplings ELKU-N
Flexible claw couplings ELKUN KWN 01 Couplings from Dresden / Germany By specialists for specialists řemeny, převody a lineární technika general information buffer part hub technical features The flexible
More informationHardinge 5C Gear-Driven Indexer
Indexer/Rotary Hardinge 5C Gear-Driven Indexer Quotation To: Budgetary Quote Prices Valid for 30 Days Your Hardinge Representative: Al Comstock 607.378.4044 al.comstock@hardinge.com Hardinge Inc. One Hardinge
More informationEasy Flow Indicator Magnetisch-Induktiver Durchflussmesser. Type 8024 For Insertion Fittings. Analog Flow Rate Indicator, 1/2"-16"; P=87 PSI
Analog Flow Rate Indicator, 1/2"-16"; P=87 PSI Advantages / Benefits Reduced costs of ownership up to 6% Economic integration in pipe systems without any additional piping Shows flow rate with a clear,
More informationSERIE 59. Rear clamp. Frontal clamp HIGH RESOLUTION HOLLOW SHAFT INCREMENTAL ENCODER FOR INDUSTRIAL APPLICATIONS
HIGH RESOLUTION HOLLOW SHAFT INCREMENTAL ENCODER FOR INDUSTRIAL APPLICATIONS Resolution up to 50.000 pulses per turn External diameter 58 mm Hollow shaft from Ø 10 to 14 mm Protection class IP67 according
More informationPrime Railway Services Radial Door - Order Form
Radial Door - Order Form Prime Part # 1130 Customer/Location: Tel: Fax: Quantity: Door ID#: Door Type: Tri Bi Door Location: BR BL AR AL BL Doors Only: Sliding Door or Pan Exterior Door Colour Red Yellow
More information