STAGE SCAN ENGLISH INSTRUCTION MANUAL INSTALLING THE PROJECTOR. (8 2 ) 2.5 m ENGLISH
|
|
- Harry Sharp
- 5 years ago
- Views:
Transcription
1 ENGLISH STAGE SCAN HMI INSTRUCTI MANUAL IMPORTANT: Read carefully. It is essential for the correct and safe use of the equipment that erectors and operators should be fully conversant with the information and instructions given in this manual. INSTALLING THE PROJECTOR Unpacking Open the box, remove the projector from the packing and place it on a flat horizontal surface. Unpack the standard accessories supplied with the equipment. Inspect the lamp change label () and replace with one of the optional language versions if necessary. Make certain that the label is never removed, as it displays important safety information. Fitting the lamp Refer to directions for replacement of the lamp given under heading MAINTENANCE. Removal of transit bands Loosen the knob () and remove the effects cover () from the projector. Locate the effects assembly frame and remove all elastic transit bands () from the colour, filters. Replace the cover and tighten the knob. Installing the projector The projector can be mounted in any position without its operating characteristics being affected. IMPORTANT: fix the projector in the desired position utilizing the holes in the bracket (). Secure preferably using two ø bolts with nuts and lock washers. Make certain that the anchorage is stable before positioning the projector. ENGLISH Fitting the safety wire The projector must never be erected without the safety wire (). The wire is secured to the gantry or other structure, then anchored to the eye bolts () on the projector itself. Initial assembly operations Position the block () over the threaded holes on the projector housing, offer the graduated plate () and secure with the eyebolt (), then fit the knob () and washer (). Align the bracket () with the plate () so as to give the desired height, insert the bushing (), the countersunk washer () and the screw () in the selected holes and secure with the Allen key supplied. The bracket () can also be fitted from the underside of the projector by reversing the position of the graduated plates (). Adjust the bracket to the desired angle and secure by tightening the knobs (). Fix the safety wire () of the effects cover () and the lamp access cover () to the graduated plate (). Fit the four side handles () with the screws () provided. IMPORTANT: the safety wire must secured to the projector and to the supporting structure in such a way that if the bracket should fail, the projector will fall as short a distance as possible. Following any such failure, the safety wire must be replaced with a genuine Clay Paky spare. Minimum distance from target objects The projector must be positioned in such a way that objects struck by the beam are located at least. m ( ) from the lens. ( ). m HMI Minimum distance of inflammable materials from any part of the equipment:. m ( ). The appliance may be mounted on surfaces rated normally inflammable. IMPORTANT: For better and more reliable operation of the projector, the ambient temperature must not exceed C ( F). Protection factor IP : the appliance is protected against penetration of solid bodies more than mm (. ) in diameter (first digit ), but can be damaged by spray, jet, drip or rain water (second digit ).
2 .... INSTALLING THE MIRROR HEAD POWER SUPPLY AND INTERFACE Unpacking Open the box, take out the mirror head, place it on a horizontal surface and remove the elastic transit bands () from the Tilt motor. Connecting to the electrical power supply The operations described in this heading must be carried out by a licensed electrician. It is good policy to connect projectors to the power supply by way of dedicated switches, so that each can be turned on and off individually from a remote station. Alimentation L N Fitting the mirror head Fit the mirror head () to the projector and secure with the three knobs (). Connect the mirror head plug () to the socket () located on the front of the projector. Connect the metal safety wire () to the tag () on the projector. The projector is designed to operate at the voltage and frequency indicated on the electrical data plate () affixed to the rear end. Check that these two values correspond to the mains voltage and frequency, or if not, proceed as indicated below. Selection of voltage/frequency Open up the effects compartment of the projector by lifting the relative cover (see heading MAINTENANCE) and, using the appropriate size Allen key, remove the cover () from the voltage change terminal (). Use a screwdriver to disconnect the cable () from the terminal it currently occupies and reconnect to the terminal alongside, referring to the label () alongside the terminal. Having completed the operation, refit the cover () and close the effects compartment. Changing the lens hood Loosen the screws () a few turns without removing completely, then dislodge the standard lens hood () by drawing it upwards and inwards, taking care to avoid contact with the mirror. Remove the wide-angle mirror head lens hood () out of the projector packing, and fit it in place of the standard hood. Check that the lens hood is in the correct position (slots located fully behind the screw heads), then retighten the screws. Verify that the lens hood produces the required effect by selecting % TILT (with dip-switch off) and sliding the PAN control from % to %. IMPORTANT: the projector must be connected to a power supply circuit having a proper earth system (Class I appliance). Connecting the control signals RS /(PMX) - DMX CNECTI RS/ DMX Projectors are wired up to the controller and one to the next using two-core screened cable and Cannon pin XLR type plug/socket connectors. To connect a DMX line, a terminating plug () with a Ω resistor wired between pins and must be fitted to the last projector connected in series; the plug is not required when using a RS/(PMX) signal. The wires must not come into contact with each other or with the metal casing of the plug. The casing of the plug/socket must be connected to the screen and to pin of the connectors. SCREEN SCREEN RS/ (PMX) SIGNAL SIGNAL DMX SIGNAL SIGNAL Having completed the operations described above, press the on/off switch (). Check that the lamp comes on and that the auto-reset sequence starts.
3 Having completed all the operations indicated thus far, loosen the knobs (), manoeuvre the projector on the bracket () until the beam is directed at centre scene, then retighten the knobs (). Adjusting the mirror head The beam can be positioned not only by moving the entire projector, but also by adjusting the mirror head. To do this, loosen the three knobs (), turn the mirror head to the desired position, and retighten the knobs. DIGITAL START ADDRESS SELECT OPTI SELECT DIGITAL INPUT LEDS Projector address codes A single STAGE SCAN projector utilizes control channels (plus one optional channel). To ensure that the different projectors are addressed correctly by the controller, a code must be assigned to each one. The operation is carried out on each STAGE SCAN by setting the dip-switches as indicated in the table below. Spotlight selection DIGITAL INPUT TEST ENGLISH CODE TEST Projector - Channels - Projector - Channels - Projector - Channels - Projector - Channels - Projector - Channels - Projector - Channels - CHANNEL FUNCTIS AND OPTIS Setting the TEST switch to the position for a few seconds with the projector powered-up, an auto-reset routine is carried out. Leaving the TEST switch at the position for a longer period, a full self-test program will be completed; once the operation has terminated, return the switch to the position. Projector - Channels - Projector - Channels - Projector - Channels - Projector - Channels - POSITIING THE PROJECTOR Alignment procedure Before positioning the projector, set the channels as shown in the following table. CHANNEL IRIS COLOUR EFFECTS FROST/FIXED PRISM DIMMER/STOPPER/STROBE PAN TILT MULTI STEP ZOOM FOCUS ROTATING PRISM SELECTI PRISM ROTATI FIXED GOBO SELECTI ROTATING GOBO SELECTI GOBO ROTATI CYAN MAGENTA FUNCTI YELLOW LAMP CTROL (*) + + OPTIS DISABLE LAMP / COL ENABLE MINS LAMP EFFECTS PAN TILT + GOBO CHANNEL POSITI OF SLIDER IRIS % (maximum aperture) COLOUR EFFECTS - FROST/FIXED PRISM % (white beam) DIMMER/STOPPER-STROBE % (white beam) PAN % (central position) TILT % (central position) MULTI STEP ZOOM - FOCUS - ROTATING PRISM SELECTI - PRISM ROTATI - FIXED GOBO SELECTI - ROTATING GOBO SELECTI - GOBO ROTATI - RED % (white beam) GREEN % (white beam) BLUE % (white beam) LAMP CTROL % (*) Channel enabled only with options and. Select the options by setting the dip-switches as indicated. OPTI FUNCTI Color wheel linear movement Color wheel fixed step advance Lamp control and recalibration disable Lamp control and recalibration enable * Lamp control (channel ) enable Lamp off after Swins blackout; channel disable Frost/Fixed prism and fixed gobo wheels linear movement Frost/Fixed prism and fixed gobo wheels fixed step advance PAN Direction change TILT Direction change * Option is enabled only with option.
4 IRIS - channel Operation with option MAXIMUM APERTURE FACE PRISM. HEAVY FROST. LIGHT FROST. FROST WITH HOLE. MINIMUM APERTURE. WHITE COLOUR EFFECTS - channel Operation with option FAST RAINBOW ( rpm). SLOW RAINBOW ( rph) COLOURS + WHITE COLOURS U.V. FILTER + COLOURS U.V. FILTER BLUE WITH HOLE + U.V. FILTER BLUE WITH HOLE YELLOW WITH HOLE + BLUE WITH HOLE YELLOW WITH HOLE RED + YELLOW WITH HOLE RED COLD FILTER + RED COLD FILTER HOT FILTER + COLD FILTER HOT FILTER WHITE + HOT FILTER - -. WHITE DIMMER/STOPPER/STROBE - channel -. - OPEN. FAST STROBE ( flash/sec.). SLOW STROBE ( flash/sec.) OPEN. CLOSED Operation with option COLOURS U.V. FILTER BLUE WITH HOLE RED COLD FILTER WARM FILTER WHITE FAST RAINBOW ( rpm) SLOW RAINBOW ( rph) YELLOW WITH HOLE PAN - channel Operation with option BIT %. FROST/FIXED PRISM - channel Operation with option Operation with option -. - FACE PRISM BIT % HEAVY FROST LIGHT FROST FROST WITH HOLE WHITE.
5 TILT - channel Operation with option BIT %. ROTATING PRISM SELECTI - channel -. - FACE PRISM (D) CYLINDRICAL PRISM (TRAIL) FACE PRISM FACE PRISM WHITE ENGLISH Operation with option PRISM ROTATI - channel BIT % FAST ( rpm) STOP. SLOW ( rph) STOP. SLOW ( rph).. FAST ( rpm). POSITI. POSITI. POSITI. POSITI. POSITI. POSITI. POSITI MULTI STEP ZOOM - channel -. - APERTURE APERTURE APERTURE APERTURE APERTURE APERTURE FIXED GOBO - channel Operation with option -. - GOBO GOBO GOBO GOBO WHITE FOCUS - channel Operation with option FAR GOBO. GOBO. GOBO. GOBO. NEAR. WHITE
6 ,,,,, ROTATING GOBO - channel GOBO ROTATI - channel STOP COLOUR MIX - channels - - CHANNEL CYAN CHANNEL CHANNEL MAGENTA -. - GOBO GOBO GOBO * GOBO * WHITE * Gobo in dichroic glass.. SLOW ( rph) STOP. SLOW ( rph) STARTER - channel Operation with option and option... FAST ( rpm). FAST ( rpm). POSITI YELLOW. POSITI. POSITI. POSITI. POSITI. POSITI. POSITI LAMP LAMP * *. LAMP LAMP COLOR OUT COLOR IN LENS UNITS GRAPHS SHOWING BEAM DATA AND ILLUMINATI VALUES Lens unit only.. LUX,,,,,,,, FC DISTANCE m DISTANCE ft in,,,,,,,,,, DIAMETER m DIAMETER ft in Additional lens--.. LUX,,,,,,,, FC DISTANCE m DISTANCE ft in,,,,,,,,,, DIAMETER m DIAMETER ft in Additional lens--.. LUX,,,,,,,, FC DISTANCE m DISTANCE ft in,,,,,,,,,, DIAMETER m DIAMETER ft in Additional lens--... LUX,,,,,,,, FC DISTANCE m DISTANCE ft in,,,,,,,,,, DIAMETER m DIAMETER ft in Additional lens--.. LUX.,,,,,, FC DISTANCE m DISTANCE ft in,,,,,,,,,, DIAMETER m DIAMETER ft in Additional lens--... LUX.,,,,,, FC DISTANCE m DISTANCE ft in,,,,,,,,,, DIAMETER m DIAMETER ft in
7 MAINTENANCE IMPORTANT: isolate the projector from the electrical power supply before commencing maintenance work of any description. The maximum temperature on the outer surface of the projector under normal operating conditions is C ( F). After switching off, do not remove any part of the projector for at least minutes, as indicated on the lamp change label (). Once this time has elapsed, the risk of a lamp exploding is practically zero. If the lamp needs changing, wait a further minutes to avoid the risk of burns. In the event of a lamp exploding, the appliance is designed to prevent fragments of glass from being scattered. Lenses and clear filters supplied with the appliance must be fitted at all times, and if visibly damaged must be replaced promptly with genuine spares. Changing metal gobos Having ed the projector, identify the gobo to be replaced and push gently toward the clips () until free. Take the selected replacement from the holder () on the gobos/iris plate. Offer the new gobo to the two clips, push gently and locate behind the third, checking for flatness. ENGLISH Opening the projector Free the lamp access cover () by loosening the knob (), and/or loosen the knob () to allow removal of the effects cover (). Once the necessary work has been completed, refit the cover and retighten the knob. Changing dichroic/photo gobos Having ed the projector, identify the dichroic gobo to be replaced and push gently until the spring () is free of its seat. Take care that the spring does not drop into the projector. Replace the gobo and locate the spring (), inserting the two ends first and then making secure by pressing on the remaining part of the spring. Routine cleaning To maintain the light output of the projector undiminished, parts that tend to accumulate dust and grease must be cleaned periodically. In most circumstances, the projector will give long and trouble-free service if these simple guidelines are followed. To remove dirt from the lenses and filters, use a soft cloth moistened with any liquid detergent suitable for cleaning glass. Changing the lamp Open the projector, loosen the two side nuts () of the lamp to be changed and remove it from the supports (). Remove the new lamp from its packaging, loosen the two side nuts () and locate the lamp in the supports (). Finally, retighten the nuts. IMPORTANT: do not use solvents or alcohol. Parts that need cleaning frequently. Parts that need cleaning monthly. The gobo wheel can be cleaned with a paintbrush. Internal components should also be given a general clean once a year, dislodging dust and dirt with a brush and removing it simultaneously with a vacuum cleaner. IMPORTANT: for uniform distribution of the light beam, the lamp must be positioned so that the glass pip () on the bulb does not coincide with the optical axis of the projector. With this in mind, locate the pip as high up as possible. CAUTI: The projector uses a high pressure discharge lamp with external starter. - When fitting a new lamp, read the manufacturer s instructions carefully. - The lamp must always be changed without delay if damaged or deformed by heat. Lubrication To ensure that rotating gobos and prisms continue to operate smoothly, the bearings should be lubricated with oil every six months: use only Kernite LUBE-K-AHT (p/n /). Apply the oil using a syringe with a fine needle. Avoid over-lubricating, as excess oil could be spattered during rotation. The rails of the focusing mechanism should be cleaned and lubricated using a cloth moistened with Kernite WAY-LUBE oil (p/n /). Changing the colour filters Having ed the projector, identify the filter to be changed, grip firmly between thumb and forefinger and push against the spring clip () until free of the fixed clips (). Bend the filter outwards and remove. Offer the new filter to the spring clip () and anchor behind the fixed clips (). Lubrication of mirror head clutches Check periodically that the grease applied to the mirror pan and tilt clutches is in good condition; if not, remove and regrease with Kernite LUBE-K-AC (p/n /) to ensure smooth and even movement of the mirror.
8 TROUBLESHOOTING WIRING DIAGRAM PROJECTOR DOES NOT LIGHT UP ELECTRICS NOT WORKING PROJECTI FAULTY REDUCED BRIGHTNESS FAULTS L SW FAN R BATT. h R C -V/Hz -/Hz BALLAST HOT IGNITOR LAMP I POSSIBLE CAUSES No electrical power supply. Lamp expended or faulty. Signal transmission cable short-circuiting or disconnected. Address codes incorrect. Defect in electronic circuits. Lenses broken. Deposit of dust or grease. CHECKS AND REMEDIES Check that power is available at the mains socket. Change lamp (see instructions). Change cables. See projector coding instructions. Contact an authorised technician. Contact an authorised technician. Clean (see instructions). E N H YELLOW DIGITAL G MAGENTA R ASCAN () DRIVERS F E D C B IRIS CYAN COLOR DIMMER PAN DISK STOPPER STROBE A TILT LAMP LAMP E N L L N MSW fuse -V.V t TECHNICAL DATA R ELECTRICAL MECHANICAL SPECIFICATIS Power supply - V Hz - V Hz Lamp Metal halide type with special built-in power supply unit. Type of lamp: HMI W - Cap SFc,- - Colour temperature K - Luminous flux lm - Average life h Power consumption VA at V Hz Correction factor µf standard Motors N. microstepping motors with full microprocessor control. Lamp hourmeter Incremental non-resettable count. OPTICAL SYSTEM Main optical unit in diecast aluminium, incorporating twin lens condenser and a reflector of high luminous efficiency. CTROL SYSTEMS Channels N. + control channels. Inputs The STAGE SCAN will accept digital signals from controllers or computers. Digital serial input: RS/(PMX) or DMX MIRROR HEAD Head rotatable through on projector housing. Graduated scale for easy and accurate positioning. Anchorage for safety chain. Mirror of ultra high luminous efficiency. Movement Produced by two controlled microstepping motors. Infinitely variable speed of rotation; Maximum values: - PAN =. sec ( ) - TILT =. sec ( ) Continuous and uniform movement. Resolution: - PAN = ±. ( ) - TILT = ±. ( ) CSTRUCTI FEATURES Safety devices Power supply shuts off automatically in the event of overheating or cooling system failure. Power shuts off automatically when cover is ed. Cooling Forced ventilation cooling system using axial flow fans. Housing Extruded die-cast aluminium. Epoxy powder coated finish. Four side handles. Mounting Steel bracket with epoxy powder coated finish. Six installation positions, mm ( ) apart. Bracket adjustable through with graduated scale to assist positioning. Anchorage for safety chain. Operating position Will function in any position. Weights and dimensions Projector: kg. ( lbs) Mirror head:. kg. ( lbs ozs) (. ) (. ) (. ) (. ) H ROTAT. GOBO CHANGE G GOBO ROTAT. F MULTI STEP ZOOM STEPPING MOTOR ASCAN (X) DRIVERS E D ROTAT. PRISM PRISM ROTAT. CHANGE STEPPING MOTOR C FOCUS B A FROST FIXED PRISM GOBO CHANGE The specifications published in this manual are not binding, and may be revised or updated at any time by Clay Paky without notice in the interests of improving product quality. The products referred to in this manual comply with EC Directives on: Low Voltage / Electromagnetic Compatibility /
GOLDEN SCAN 3 INSTRUCTION MANUAL ENGLISH INSTALLING THE PROJECTOR INSTALLING THE MIRROR HEAD. (8 2 ) 2.5 m. (5 11 ) 1.8 m HMI 575 ENGLISH
ENGLISH GOLDEN SCAN HMI HMI HMI TV INSTRUCTI MANUAL IMPORTANT: Read carefully. It is essential for the correct and safe use of the equipment that erectors and operators should be fully conversant with
More informationSHADOW INSTRUCTION MANUAL ENGLISH POWER SUPPLY AND INTERFACE INSTALLING THE PROJECTOR. (8 2 ) 2.5 m. (5 11 ) 1.8 m ENGLISH
SHADOW QS-ST HMI QS-LT HMI Basic HMI Basic HMI IMPORTANT: Read carefully. It is essential for the correct and safe use of the equipment that erectors and operators should be fully conversant with the information
More informationIGLOO IGLOO EASY INSTRUCTION MANUAL
ENGLISH EASY C695 C698 INSTRUCTION MANUAL PRELIMINARY Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky
More informationIGLOO IGLOO EASY INSTRUCTION MANUAL
ENGLISH EASY C695 C698 INSTRUCTION MANUAL PRELIMINARY Congratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product, as all the others in the rich Clay Paky
More informationSOLO 250 PR PR LIGHTING LTD. No.571, Yingbin Road, Dashi Panyu, Guangzhou, China
SOLO 250 PR-2255 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a
More informationOstar Eye K6. Beam and Kaleido Effects. User manual. Please read the instructions carefully before use
Ostar Eye K6 Beam and Kaleido Effects User manual Please read the instructions carefully before use TABLE OF CONTENTS 1. Safety Instructions... 2 2. Technical Specifications... 4 3. How To Control The
More informationInstruction Manual. Version 1.2
Instruction Manual Version 1.2 Elation Professional 4295 Charter Street Los Angels CA 90058 e-mail: info@elationlighting.com Web site: www.elationlighting.com (V1.2) 2 Contents 1 Introduction...5 1.1 Safety
More informationPROFESSIONAL SHOW LIGHT
Instruction Manual PROFESSIONAL SHOW LIGHT Beast 280(Beam+Spot) ------------------------------ 2014 Ver8.11----------------------------------- Unpacking: Thank you for purchasing Beast280(Beam+Spot). Every
More informationLED SPIDER MOVING HEAD LIGHT
LED SPIDER MOVING HEAD LIGHT MJ-1031C (4IN1) INSTRUCTION MANUAL Thank you for choosing our LED spider moving head light. For the sake of your safety, Please read and follow these instructions carefully
More informationPILOT 150 PR-2150 PR LIGHTING LTD Yingbin Road Dashi Panyu Guangzhou , China
PILOT 150 PR-2150 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a
More informationProfessional Entertainment Technology LED BEAM 300 LED-MB50. Innovation, Quality, Performance 23-
Innovation, Quality, Performance 23- LED BEAM 300 LED-MB50 User Guide Professional Entertainment Technology EC Declaration of Conformity We declare that our products (lighting equipments) comply with the
More informationLED BEAM 300 LED-MB50. User. Guide. Professional Entertainment Technology
LED BEAM 300 LED-MB50 Guide User Professional Entertainment Technology TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. How To Set The Unit 4. How To Control The Unit 5. Troubleshooting
More informationProfessional Entertainment Technology LED BEAM 300 LED-MB50. User. Guide
Professional Entertainment Technology LED BEAM 300 LED-MB50 Guide User 1- 1. Safety Instruction WARNING Please read carefully the instruction, which includes important information about the installation,
More informationProfessional Entertainment Technology. imove 50SR. Innovation, Quality, Performance 21-
Innovation, Quality, Performance 21- imove 50SR User Guide Professional Entertainment Technology EC Declaration of Conformity We declare that our products (lighting equipments) comply with the following
More informationEternal Lighting. Premier150 Spot. User Manual
Eternal Lighting Premier150 Spot User Manual Introduction: Thank you for your purchase of the Premier150 Spot. When unpacking and before disposing of the carton, check there is no transportation damage
More informationOstar Eye K18. Beam and Kaleido Effects. User manual. 6. Fixture Cleaning. Please read the instructions carefully before use
6. Fixture Cleaning The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the Ostar Eye K18 Beam and
More informationFamiliar, and yet very surprising
MAC 575 Krypton Familiar, and yet very surprising The MAC 575 Krypton is the latest in the Krypton series of luminaires that combines recognized MAC moving head quality with feature-packed modularity,
More informationCP 64 BD15 CP 64 PD15
COLOR PAR 64 CP 64 BD15 CP 64 PD15 User Manual Please read the instruction carefully before use Contents 1. Safety Instruction...2 2. Technical Specification...3 3. Installation...4 4. DMX Address Setting...4
More information7x15W 4IN1 Infinity Rotation LED Pixel Bar. This product manual contains important information about the safe
Pixel Beam K7 7x15W 4IN1 Infinity Rotation LED Pixel Bar This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions
More informationXRLED 300 SPOT PR-8157
XRLED 300 SPOT PR-8157 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual
More informationXRLED 1200 SPOT PR-8180
XRLED 1200 SPOT PR-8180 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual
More informationXRLED 500 SPOT PR-8160
XRLED 500 SPOT PR-8160 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual
More informationUSER MANUAL. 17R Spot\Beam Light. Please Read Over This Manual Before Operating The Light Fixture
USER MANUAL 17R Spot\Beam Light Please Read Over This Manual Before Operating The Light Fixture 1 PRODUCT SPECIFICATIONS 1.1 PRODUCT SPECIFICATIONS The 17R Spot\Beam light is an improved version of Beam
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationSpectrum Laser. User manual UK. Version 1.0
Spectrum Laser User manual 152.753UK Version 1.0 CAUTION 15. Disposal : Please disposal of the unserviceable device according to the current statutory requirements. Please read this manual fully before
More informationSPOT MOVING HEAD M1S150W USER MANUAL. For safety, please read this user manual carefully before initial use.
SPOT MOVING HEAD M1S150W USER MANUAL For safety, please read this user manual carefully before initial use. Event Lighting reserves the right to revise the manual at any time. Information and specifications
More informationBlue Weapon Laser. User manual UK. Version 1.0
Blue Weapon Laser User manual 152.754UK Version 1.0 CAUTION 15. Disposal : Please disposal of the unserviceable device according to the current statutory requirements. Please read this manual fully before
More informationMMX Blade. Light source Philips MSR Platinum 35. Light output lm. Zoom range 8,5-45,5
MMX Blade The Robin MMX Blade is based on the new technology MMX discharge fixture, comparable output to 1200 W luminaires, the MMX Blade adds a framing shutter system into the optical path. Four fast,
More informationPANDA II PR- 2100B. PR LIGHTING LTD. Yingbin Road, Dashi Panyu, Guangzhou, China
PANDA II PR- 2100B This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in
More information10W LED PIN SPOT. User Manual LED-PS10D W. Innovation, Quality, Performance. Professional Entertainment Technology 11-
Innovation, Quality, Performance 11-10W LED PIN SPOT LED-PS10D W User Manual Professional Entertainment Technology TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Installation 4.
More informationGobo Projector XP 80W
Gobo Projector XP 80W User Manual Order code: EQLED084 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CARE- FULLY BEFORE YOUR INITIAL START-UP! Before your initial start-up, please
More informationUser Guide. Please read these instructions carefully before use
User Guide Please read these instructions carefully before use EC Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark
More informationThe Robe MMX is a new technology discharge fixture that has similar light output to most existing 1200W luminaires.
The Robe MMX is a new technology discharge fixture that has similar light output to most existing 1200W luminaires. The unit is based on the all new Robin advanced technology design that provides Brighter,
More information3D OBJECTS RGB LASER. Order ref: UK User Manual
TECHNICAL SPECIFICATION Voltage : 230Vac, 50/60Hz Blue : 300mW 455nm Fuse : 2A Slow blow DMX Channels : 20 Dimensions : 220 x 176 x 99mm Laser Class : 3B Red Laser: 100mW 638nm Power Consumption : 45W
More informationBEAM MOVING HEAD WITH 5R LAMP, 8-FACET PRISM, MOTORIZED FOCUS AND FROST USER GUIDE
BEAM MOVING HEAD WITH 5R LAMP, 8-FACET PRISM, MOTORIZED FOCUS AND FROST USER GUIDE 10409 - Version 1 / 11-2015 English Sword5R - Beam moving head with Philips MSD PLATINUM 5R lamp 1 - Safety information
More informationTB-1230 QW. User Manual Please read the instruc on carefully before use
TB-1230 QW User Manual Please read the instruc on carefully before use CONTENTS 1. Safety Instructions... 2 2. Technical Specifications... 3 3. How To Set The Unit... 4 3.1 Control panel... 4 3.2 Main
More informationRevo 120. User Manual
Revo 120 User Manual GENERAL INFORMATION Congratulations, you have just purchased one of the most innovative and reliable lighting fixtures on the market today! The Revo 120 has been designed to perform
More informationMATRIX 25E. Matrix Beam Wash, ArtNet, RDM. User manual. Please read the instructions carefully before use
MATRIX 25E Matrix Beam Wash, ArtNet, RDM User manual Please read the instructions carefully before use TABLE OF CONTENTS 1. Safety Instructions... 2 2. Technical Specifications... 4 3. How To Control The
More informationUSER MANUAL. 10R Spot\Beam Light. Please Read Over This Manual Before Operating The Light Fixture
USER MANUAL 10R Spot\Beam Light Please Read Over This Manual Before Operating The Light Fixture 1 PRODUCT SPECIFICATIONS 1.1 PRODUCT SPECIFICATIONS The 10R Spot\Beam light is an improved version of Beam
More informationX-3 LED. Owner s Manual ROBOHEAD
X-3 LED Owner s Manual ROBOHEAD Thanks a lot for purchasing our LED robohead. Please read this user manual carefully and follow the instructions to avoid danger or damage to the unit due to mishandling.
More informationPHOS 20/40 downlight OWNER'S MANUAL
PHOS 20/40 downlight OWNER'S MANUAL TABLE OF CONTENTS Safety Instructions...4 Electrical Safety... 4 Lamp Safety...4 Burns and Fire Safety... 5 Safety During Installation And Operation... 5 Technical Overview...
More informationXRLED 300 Spot PR-8157
XRLED 300 Spot PR-8157 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual
More informationSAMURAI SCAN 50 LED-SC50D. User Guide. Innovation, Quality, Performance. Professional Entertainment Technology 19-
SAMURAI SCAN 50 LED-SC50D Innovation, Quality, Performance User Guide Professional Entertainment Technology 19- EC Declaration of Conformity We declare that our products (lighting equipments) comply with
More informationRoboColor III. user manual
RoboColor III user manual INTRODUCTION Congratulations on your choice of the RoboColor III system, designed and manufactured by Martin Professional. The RoboColor III is a high performance, automated color
More informationPRODUCT SPECIFICATIONS
FOS Spot 90W 1 PRODUCT SPECIFICATIONS TECHNICAL SPECIFICATION Voltage: 100/240 Volt AC, 50/60 Hz. Power Consumption: 135 Watt. Light Source: 90 Watt LED, 8000K Beam angle: 18 Colors: 7 dichroic color filters.
More informationUser s manual. Easy Scan XT3 LED
User s manual Easy Scan XT3 LED Table of content 1. Safety instructions... 3 2. Before you begin... 4 2.1. What is included... 4 2.2. AC Power... 4 3. Introduction... 4 3.1. Features... 4 4. Product overview...
More informationTable of Contents. 1. Before You Begin...1
User Manual Table of Contents Table of Contents 1. Before You Begin...1 What is Included... 1 Unpacking Instructions... 1 Typographic Conventions... 1 Icon Meaning... 1 Safety Notes... 2 Expected LED Lifespan...
More informationBW-108. Building Wash BW-108. User Guide. Advanced LED Technology
Building Wash User Guide Advanced LED Technology TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Change Beam Angle 4. Main Function 5. How To Control The Unit 6. Troubleshooting 7.
More informationLED MOVING HEAD FLEX BEAM K8 RGBW. User Manual. Please read the instruction carefully before use
LED MOVING HEAD FLEX BEAM K8 RGBW 1 User Manual Please read the instruction carefully before use CONTENTS 1. Safety Instructions... 3 2. Technical Specifications... 4 3. How To Set The Unit... 5 3.1 Front
More informationLED PANEL. User Manual Please read the instructions carefully before use LED-7TC. Innovation, Quality, Performance 15-
LED PANEL LED-7TC Innovation, Quality, Performance User Manual Please read the instructions carefully before use 15- 9. Fixture Cleaning TABLE OF CONTENTS 1. Safety Instructions 2. Technical Specifications
More informationHaze 800 DMX. User Guide. English
Haze 800 DMX User Guide English Introduction Box Contents Haze 800 DMX Remote Control (wired) User Guide Safety & Warranty Manual Support For the latest information about this product (documentation, technical
More informationTECHNICAL DATA. V-PIX Quad Bar. Product code CL-VPIX-4-40 Light colour Full spectrum 8 / 480 (see above)
TECHNICAL DATA V-PIX Quad Bar Specification Product Product code CL-VPIX-4-40 Light colour Full spectrum Channels 8 / 480 (see above) Driver Built in Control protocol Art-Net, DMX512, Kling-Net Power and
More informationRoboScan Pro 518. user manual
RoboScan Pro 518 user manual 1998-2000 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any means, without permission in writing from Martin
More informationTech doc ENGLISH Infinity ib-16r Ordercode: 41532
Tech doc ENGLISH Infinity ib-16r Highlite International B.V. Vestastraat 2 6468 EX Kerkrade the Netherlands Description The ib-16r is a truly versatile moving head offering a beam, spot and wash effect
More informationFUSION SPOT MKII EQUINOX. Contents. User Manual. Order codes: Black housing - EQLED Safety Instructions. 2. Features & Specifications
EQUINOX FUSION SPOT MKII Contents 1. Safety Instructions 2. Features & Specifications 3. How To Set The Unit 4. Troubleshooting User Manual 5. Fixture Cleaning Order codes: Black housing - EQLED008 1.
More informationLED PANEL. User Manual Please read the instructions carefully before use LED-212RGB TABLE OF CONTENTS. 1. Safety Instructions
TABLE OF CONTENTS LED PANEL 1. Safety Instructions 2. Technical Specifications 3. Installation 4. How to set the unit 5. How to control the fixture 6. DMX512 Configuration 7. DMX512 Connections 8. Troubleshooting
More informationLED W RGBA User Manual
LED- 245-1W RGBA User Manual Please read the instructions carefully before use CONTENTS 1. Safety Instructions...2 2. Technical Specifications...3 3. How To Set The Unit...4 3.1 Control Panel...4 3.2 Main
More informationUser Guide Professional Entertainment Technology
Technical Specifications Power AC 120V~60Hz AC 230/240/250V~50/60Hz Fuse 20mm Glass T6.3A Fast Blow 20mm Glass T5A Fast Blow Lamp Dimension Weight HID 150W 695 x 340 x 250 mm (IR-5S/5B-HID) 360 x 340 x
More informationimove 50SR LED-MS50A User Guide Professional Entertainment Technology
imove 50SR LED-MS50A User Guide Professional Entertainment Technology TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. How To Set The Unit 4. How To Control The Unit 5. Troubleshooting
More informationRevueLED 150 Profile 3200K 26 LED spotlight. user manual
RevueLED 150 Profile 3200K 26 LED spotlight user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de
More informationBMFL Blade. Light source 1700 W OSRAM Lok-it! HTI 1700/PS. LIGHT OUTPUT lm, m, m.
BMFL Blade Four fast shutter blades with smooth and precise movement in the new BMFL Blade lighting fixture. Individually angled and positioned within a frame - which itself can rotate through 90 degrees,
More informationRobot Light V2. User Manual
Robot Light V2 User Manual 2 Please read over this manual before operating the light. Introduction Unpacking: Thank you for purchasing the Robot Light V2. Every Robot Light V2 has been thoroughly tested
More informationPHOS mini OPERATING INSTRUCTIONS
PHOS mini OPERATING INSTRUCTIONS TABLE OF CONTENTS Safety Instructions...4 Electrical Safety... 4 Burns and Fire Safety... 5 Lamp Safety...5 Safety during installation and operation... 6 Technical Overview
More information714SX2. 700SX2-2000/2500 W Tungsten. Profile spot. Type: Profile spot Source: 2000/2500 W Tungsten Optics: 15 to 40 zoom
f 714SX2 700SX2-2000/2500 W Tungsten Type: Profile spot Source: 2000/2500 W Tungsten Optics: 15 to 40 zoom Profile spot The ideal zoom profile for all medium throw applications Combining power with a smooth
More informationBMFL Blade. Light source W OSRAM Lok-it! HTI 1700/PS. Tel: Fax:
Four fast shutter blades with smooth and precise movement in the new BMFL Blade lighting fixture. Individually angled and positioned within a frame - which itself can rotate through 90 degrees, providing
More informationBMFL Blade BMFL Blade 1
BMFL Blade Four fast shutter blades with smooth and precise movement in the new BMFL Blade lighting fixture. Individually angled and positioned within a frame - which itself can rotate through 90 degrees,
More informationUser Manual. Trinocular Stereo Microscope
User Manual Trinocular Stereo Microscope Model V434 XV434 Series MicroscopeNet.com Table of Contents i. Caution.. 1 ii. Care and Maintenance... 2 1. Component Illustration... 3 2. Installation 4 3. Operation....6
More information711SX2. 700SX2-2000/2500 W Tungsten. Profile spot. Type: Profile spot Source: 2000/2500 W Tungsten Optics: 8 to 16 zoom
f 711SX2 700SX2-2000/2500 W Tungsten Type: Profile spot Source: 2000/2500 W Tungsten Optics: 8 to 16 zoom Profile spot The ideal zoom profile for all very long throw applications Combining power with a
More informationMMX WashBeam. Light source. Philips MSR Platinum 35. Light output. Tel: Fax:
Encompassing all the new technologies develeoped for the MMX Spot, the WashBeam provides the lighting designer with a huge range of features and effects in a single fixture. The Phillips Platinum 35 light
More informationRobocolor II System. users guide
Robocolor II System users guide CONTENTS INTRODUCTION... 3 INSTALLING THE ROBOCOLOR II SYSTEM... 3 OPERATING WITHOUT A LIGHTING CONTROLLER - STAND ALONE... 4 OPERATING STAND ALONE IN MASTER/SLAVE MODE...
More informationSUPER LEDF10HP DATASHEET
DATASHEET LED Fresnel Spotlight 330W - CRI>95 White light, either Tungsten or Daylight balanced OVERVIEW The Super LED F10HP is a high efficiency Fresnel lens spotlight using the innovative High Power
More informationXR 330 SPOT PR PR LIGHTING LTD. 1/23
XR 330 SPOT PR-2350 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in
More informationBMFL Spot. Light source 1700 W OSRAM Lok-it! HTI 1700/PS. LIGHT OUTPUT lm, m, m.
BMFL Spot The BMFL Bright Multi- Functional Luminaire much anticipated new lighting fixture from Robe, brings a real game changer in the world of moving lights. The BMFL Spot has a custom light source
More information713SX2. 700SX2-2000/2500 W Tungsten. Profile spot. Type: Profile spot Source: 2000/2500 W Tungsten Optics: 29 to 50 zoom
f 713SX2 700SX2-2000/2500 W Tungsten Type: Profile spot Source: 2000/2500 W Tungsten Optics: 29 to 50 zoom Profile spot The ideal zoom profile for all short throw applications Combining power with a smooth
More informationB a e m W M v o i v n i g H a e d L g i h g t U E S R M N A U N A U L
Beam 200W Moving Head Light USER MANUAL 200W Beam Light Manual 1.Safety Information 3 2.Installation and Startup 5 3.Menu settings 9 4.Technical Information 10 5.Channel function 11 1 Unpacking Inspection
More informationMATRIX LED LED User Manual Please read the instructions carefully before use
MATRIX LED LED-7871 User Manual Please read the instructions carefully before use 1- 1. Safety Introductions TABLE OF CONTENTS WARNING Please read the instructions carefully which includes important information
More informationATOM. Instruction Manual. Head. from software version: 8.
Instruction Manual from software version: 8 ATOM Head support@glp.de www.glp.de Contents 1 Description of Device... 3 2 Safety Instructions... 4 3 Mounting... 6 3.1 Operating on the Floor (Upright)...
More informationSUPER LEDF6 DATASHEET
SUPER DATASHEET LED Fresnel Spotlight 120W - CRI>96 White light, either Tungsten or Daylight balanced OVERVIEW The Super LED F6 is a high efficiency Fresnel lens spotlight using the innovative High Power
More informationSTAGE TRI-PAR 18TC CP-18TC. User Manual. Please read the instructions carefully before use
STAGE TRI-PAR 18TC CP-18TC User Manual Please read the instructions carefully before use TABLE OF CONTENTS 1. Safety Instructions 2. Technical Specifications 3. How to Set the Fixture 4. How to Control
More informationUser Guide Please read these instructions carefully before use
IM-250SW Innovation, Quality, Performance User Guide Please read these instructions carefully before use 1- TABLE OF CONTENTS 1. Safety Instruction 2. Technical Specification 3. Lamp 4. How To Set The
More informationШирокий ассортимент оборудования ACME на User Guide. Professional Entertainment Technology
Широкий ассортимент оборудования ACME на www.maxlight.ru User Guide Professional Entertainment Technology EC Declaration of Conformity We declare that our products (lighting equipments) comply with the
More informationi.shine 1136 RGBW Color Stainer CN USER MANUAL
i.shine 1136 RGBW Color Stainer CN USER MANUAL Thank you very much for choosing our product. For safety purpose, please read this manual carefully before your operation. This manual included installation
More informationMH-100 Beam 36x3 LED moving head. user manual
MH-100 Beam 36x3 LED moving head user manual Musikhaus Thomann e.k. Treppendorf 30 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 13.12.2013, ID:
More information711SX2 Silent. 700SX W Tungsten. Profile spot. Type: Profile spot Source: 2000 W Tungsten Optics: 8 to 16 zoom Very low noise fan - 25 db(a)
f 711SX2 Silent 700SX2-2000 W Tungsten Type: Profile spot Source: 2000 W Tungsten Optics: 8 to 16 zoom Very low noise fan - 25 db(a) Profile spot The ultra-silent 2000 W zoom profile This variant 700SX
More informationItem ref: UK User Manual. MW-7 4-in-1 LED Mini Moving Head
MW-7 4-in-1 LED Mini Moving Head Item ref: 150.449UK User Manual Please read through this manual thoroughly before use, any damage caused by misuse of the product will not be covered by the warranty. This
More informationMegaPointe. MEGA bright with MEGA features and still compact. The MegaPointe from Robe. Light source Osram Sirius HRI 470 W RO
MegaPointe MEGA bright with MEGA features and still compact. The MegaPointe from Robe. OUR NEW REFERENCE POINT! Our all-new MegaPointe elevates the original all-in-one fixture to a whole new level. Unleash
More informationPlease read the instructions carefully before use LED PYRAMID LED-904D. Innovation, Quality, Performance 15-
Innovation, Quality, Performance 15- LED PYRAMID LED-904D User Manual Please read the instructions carefully before use Innovation, Quality, Performance 15- LED PYRAMID LED-904D User Manual Please read
More information60W SPOT MOVING HEAD USER GUIDE January 2015 version
60W SPOT MOVING HEAD USER GUIDE 10312-1 January 2015 version English Blast-60-60W LED Spot moving head with rotating gobos 2 Blast-60-60W LED Spot moving head with rotating gobos English 1 - Safety information
More information19*15W ZOOM LED Big Bee Eyes Instructions
19*15W ZOOM LED Big Bee Eyes Instructions Thank you for choosing our products. Before installation, please read this manual carefully. This product is for professionals, non-professionals do not arbitrarily
More informationZ-350 FAZER USER MANUAL
www.clubsoundrent.nl Z-350 FAZER USER MANUAL English Français Deutsch 2013 Antari Lighting and Effects Ltd. 1 User Manual Safety Information Please read the following safety information carefully before
More informationMegaPointe. MEGA bright with MEGA features and still compact. The MegaPointe from Robe. Light source Osram Sirius HRI 475/5 W RO
MegaPointe MEGA bright with MEGA features and still compact. The MegaPointe from Robe. OUR NEW REFERENCE POINT! Our all-new MegaPointe elevates the original all-in-one fixture to a whole new level. Unleash
More informationBMFL WashBeam W OSRAM Lok-it! HTI 1700/PS lm, m, m 5-45
BMFL WashBeam The strong-arm of the BMFL family - the superbly powerful BMFL WashBeam comes with extra bright output and an abundance of great features, e.g newly developed framing shutters, super wide
More informationUser Manual. Binocular Stereo Microscope. MicroscopeNet.com
User Manual Binocular Stereo Microscope Model K2213 Series MicroscopeNet.com Table of Contents i. Caution... 1 ii. Care and Maintenance... 1 1. Components Illustration... 2 2. Installation... 3 3. Operation...
More informationFT-20 Fire Training Fog Machine User Manual English
FT-20 Fire Training Fog Machine User Manual English 2017 Antari Lighting and Effects Ltd. 1 User Manual - English Safety Information Please read the following safety information carefully before operating
More informationCOLOR PAR 56 COLOR PAR 64. User Manual Please read the instructions carefully before use. Широкий ассортимент оборудования ACME на
COLOR PAR 56 TABLE OF CONTENTS COLOR PAR 64 1. Safety Instructions 2. Technical Specifications 3. Installation 4. DMX512 Address setting 5. How to control the fixture 6. DMX 512 Connections 7. Troubleshooting
More informationOMM200 and OMM200T. Metallurgical Microscope
OMM200 and OMM200T Metallurgical Microscope Instruction Manual (Please read the manual carefully before using the microscope) Contents Safety ----------------------------------------------------------------------------
More information114 mm 156 mm Martin Professional A/S, Denmark.
CX-4 user manual 1 focus lens 1 2 cover screws 3 air vent 4 safety cable holes 5 mounting bracket 6 air vents 7 DIP-switch 2 3 7 8 9 10 8 data output 11 9 data input 10 lamp access & adjustment 11 AC input
More informationModel No. ET-JPF200BE
Operating Instructions Floor Stand Kit Commercial Use Model No. ET-JPF200BE ET-JPF200WE ENGLISH FRANÇAIS ESPAÑOL DEUTSCH ITALIANO * The above illustration is of this product mounted to an optional projector.
More informationZEP - 664SX WW 660SX - LED 300 W. Profile spot. Type: Profile spot Source: LED 300 W Optics: 16 to 35 zoom Colour temperature: Warm white
f ZEP - 664SX WW 660SX - LED 300 W Type: Profile spot Source: LED 300 W Optics: 16 to 35 zoom Colour temperature: Warm white Profile spot Enhanced performance for the new ZEP member! Combining power with
More informationVortex. User Manual. Order code: EQLED073
Vortex User Manual Order code: EQLED073 Safety advice WARNING FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE INITIAL START-UP! Before initial start-up, please make sure that there is
More information