4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT

Size: px

Start display at page:

Download "4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT"

Judith Wilkerson
5 years ago
Views:

80010652 Highbands Y1; Y2 1710 2690 Frequency range MHz 1710 1990 1920 2200 2200 2490 2490 2690 Polarization +45, 45 +45, 45 +45, 45 +45, 45 Gain Tilt dbi 18.2... 18.4... 18.0 18.7... 18.9... 18.4 18.

1 4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT Y set by hand or by optional RCU (Remote Control Unit) X Y2 X Port Antenna / /65 19/19dBi 0 10 /0 10 T Type No Highbands Y1; Y Frequency range MHz Polarization +45, , , , 45 Gain Tilt dbi Horizontal Pattern: Half-power beam width Front-to-back ratio, copolar db > 30 > 26 > 28 > 26 Cross polar ratio 0 Sector ±60 db Typically: 20 Vertical Pattern: Half-power beam width Electrical tilt 0 10, continuously adjustable Sidelobe suppression for first sidelobe above main beam T db Impedance Ω 50 VSWR < 1.5 Isolation, between ports db > 30 Intermodulation IM3 dbc < 150 (2 x 43 dbm carrier) Max. effective power per port Max. effective power for the antenna W 250 (at 50 C ambient temperature) 500 (at 50 C ambient temperature) Mechanical specifications /d Subject to alteration. Input Connector position Adjustment mechanism 4 x 7-16 female Bottom 2x, Position bottom continuously adjustable Wind load (at Rated N lbf Frontal: Wind Speed: 150 km/h) Maximal: Max. wind velocity km/h mph Height/width/depth mm inches Category of mounting hardware Weight kg lb Packing size mm inches Scope of supply / 315 / / 12.4 / 2.8 M (Medium) 17 / 19.2 (clamps incl.) 37.5 / 42.3 (clamps incl.) 1961 x 337 x x 14.8 x 4.4 Panel and 2 units of clamps for mm inches diameter Page 1 of 2

2 Accessories General Information Accessories (order separately if required) Type No. Description Remarks mm inches Weight approx. kg lb Units per antenna 1) 2) 3) 1) ) ) clamp Mast diameter: clamp Mast diameter: downtilt kit Downtilt angle: Accessories (included in the scope of supply) clamp Mast diameter: For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit. Wall mounting: No additional mounting kit needed. Material: Reflector screen: Aluminium. Radiator: Tin-plated zinc. Flat fiberglass radome: The max. radome depth is only 71 mm 2.8 inches. Fiber glass material guarantees optimum performance with regards to stability, stiffness, UV resistance and painting. The color of the radome is grey. All screws and nuts: Stainless steel Grounding: The metal parts of the antenna including the mounting kit and the inner conductors are DC grounded. Correlation Table Frequency range Array Connector MHz Y MHz Y2 3 4 Y1 Y2 Left Right Layout of interface: * * , Adjustment mechanism with integrated scale All dimensions in mm inches * Bottom view * Dimensions refer to radome All dimensions in mm inches /d Subject to alteration. Any previous data sheet issues have now become invalid. Page 2 of

3 Mounting Hardware Clamp Included in the Scope of Supply Suitable for mast diameter Antenna mast distance Material of clamp and screws Weight (mm) [inches] (mm) [inches] (kg) [lb] [ ] [ ] Hot-dip galvanized steel / stainless steel 1.1 [2.43] 152 [5.98] 100 [3.94] 72 [2.83] [ ] 40 [1.57] /c Subject to alteration. 40 [1.57] [ ] M10 M A = 25 Nm 35 [1.38] M8 M A = 20 Nm 64 [2.52] 125 [4.92] [ ] Please note: Kathrein does not recommend to use counter nuts. The additional nuts supplied are only meant as spares. All dimensions in mm and [inches] Any previous data sheet issues have now become invalid Page 1 of 1

General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap

➀ Thread for fixing the pro tective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive.

The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0 max.

Set downtilt angle by rotating the gearwheel. Screw on the twist protection and the protective cap again.

4 General Instructions for Adjustment Mechanism Description of the adjustment mechanism (protective cap removed): ➀ Twist protection. ➁ Downtilt spindle with integrated scale. ➀ Thread for fixing the pro tective cap or the RCU (Remote Control Unit). ➁ Gearwheel for RCU power drive. To set the downtilt angle exactly, you must look horizontally at the scale. The lower edge of the gearwheel must be used for alignment. Manual adjustment procedure: 0 max. 0 max. Remove the protective cap and the twist protection completely. Set downtilt angle by rotating the gearwheel. Screw on the twist protection and the protective cap again. Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment: /a Subject to alteration. For a description of RCU installation please refer to the respective data sheet. Page 1 of 2

General Instructions for Feederline and RCU Installation for Antennas Please note: In order not to damage the interfaces, please make sure that only the right tools are used.

Description of bottom end cap (exemplary picture): Adjustment mechanism (protective cap removed) Ventilation hole Spindle with tilting scale 7-16 female (long neck) Colour coding: Correlation of

mechanism, the protective caps have to be attached during feederline installation! Kathrein installation set: Type No. 85010077 Set has to be ordered separately!

3 Carefully place the connector and fix the nut using a torque-wrench (according to the manufacturers guidelines).

5 General Instructions for Feederline and RCU Installation for Antennas Please note: In order not to damage the interfaces, please make sure that only the right tools are used. Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench width. Description of bottom end cap (exemplary picture): Adjustment mechanism (protective cap removed) Ventilation hole Spindle with tilting scale 7-16 female (long neck) Colour coding: Correlation of each RF input to: the corresponding adjustment mechanism the frequency range the polarization Installation of the feederline connector and RCU (optional): In order to protect the adjustment mechanism, the protective caps have to be attached during feederline installation! Kathrein installation set: Type No Set has to be ordered separately! Set consists of three spanners of divers width 27, 32 and 41 mm 1.1, 1.3 and 1.6 inches 1/2 square actuation according to DIN 3120 Form C Carefully place the connector and fix the nut using a torque-wrench (according to the manufacturers guidelines). After feederline installation, the optional remote control units (RCUs) can be mounted All dimensions in mm inches These tools are suitable for 7-16 connectors with a wrench size of 27 or 32 mm 1.1 or 1.3 inches, and the RCU attachment nut with a wrench size of 41 mm 1.6 inches /a Subject to alteration. Tighten nuts within a torque range of Nm depending on connector manufacturers specifications, respectively the RCU nut with a torque range of Nm. Page 2 of 2

2-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT

2-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT B1 1695 2200 0 10 set by hand or by optional RCU (Remote Control Unit) X 65 2-Port Antenna 1695 2200 65 18dBi 0 10 T Type No. 742215V01