AK-C6A In Car Dash Camera. Instruction Manual Model Ref: MM347

Transcription

1 AK-C6A In Car Dash Camera Instruction Manual Model Ref: MM347

2 Introduction Thank you for choosing this In Car Dash Camera. This product is manufactured to the highest standards of performance and safety. This product uses a high performance chipset, with high definition video, seamless dynamic pictures which support FHD 1080P recording. Before use, please read this manual carefully. It gives important instructions about safety, use and maintenance of your camera. Remove all packaging material. You may wish to keep the packaging for future use or storage of your camera. Alternatively, dispose of accordingly. Important Safety Information WARNING - To reduce the risk of fire, electric shock, or injury: DO NOT drop the product from a great height or strike it with an object. DO NOT allow the camera to come within a close proximity of objects with a strong magnetic force, such as magnets. In addition please avoid objects that transmit strong radio-waves. These may cause the camera to become faulty or effect the image/sound quality of the recording. DO NOT use an unbranded Micro SD/TF card with your camera. Unbranded cards cannot guarantee a reliable performance from your camera. If the camera gives out intense heat, smoke or gives off a peculiar smell when charging, please unplug the camera immediately to avoid causing a fire. When charging the camera battery, leave the camera in a place where children cannot reach it to avoid the risk of electric shock. Please store the camera in a cool dry place when not in use. 01

3 Product Overview Power on/off LED light on/off Power on/off the camera: Keep pressing the power button for 3 seconds to turn on/off the camera, it will then enter into the recording mode, automatically. Keep pressing it again and the recording will stop and the video files will get saved. Power on/off the back light: After the camera is powered on, short press the Power on/off button to choose: LED light on/off/auto; in the mode of LED light auto, the LED light is controlled by photo-conductive resistance or the brightness of light sensed by the camera lens itself. Record/Photo/OK/Full Screen Start/Stop recording - In video mode, short press OK button start recording, short press it again, the recording will be stopped. Photo - In photo mode, short press OK button can take photo 02

4 Playback - In playback mode, short press the OK button to play video recordings. OK button - In video/photo mode or playback mode, short press the menu button to enter into menu, short press the up/down button to browse, short press the OK button to confirm. Full-screen button - In video/photo mode or playback mode, keep pressing the OK button to switch between fullscreen and regular mode. Down button / mute / fast forward Down button - In menu setting and camera switch mode, for the down function. Mute - In video mode, short press the down button to make the audio on/off. Note: the setting will be saved automatically, there is no need to reset once again the next time. Fast forward - In playback mode, short press the down button to play fast forward Menu In standby mode, short press the menu button, enter into main menu setting and short press the UP/DOWN button. Choose the options which you need and short press the OK button to confirm. When settings are finished, short press the Menu button until exit. Mode button In standby mode, short press the mode button to switch between different modes (Video / Photo / Playback) SOS button In video mode, if you want to protect a current video, short press SOS button to lock it, and the video file will not be covered 03

5 Installation Instructions 1. Power off the In Car Dash Camera 2. Insert the SD/TF card (not supplied) into the card slot Note: Please use a high speed SD/TF card (more than class 6), the capacity should be more than 2GB, the Dash Camera can support a SD/TF card with up to 32GB of storage. 3. Fasten the camera to the car using the fitting supplied 4. Insert the car charger into the car cigarette lighter 5. Connect the car charger and USB interface of camera with the charger extension cable 6. Adjust the lens and keep the view parallel with the ground. 7. Start the In Car Dash Camera and check to see if the camera is installed correctly. Note: When camera is installed in the correct way, the system working indicator light will be turned on; the camera will be turned on and in video recording mode, the shoot indicator light will flash. Please check that the picture of the screen is normal. 04

6 Functions 1. Recording automatically once the camera is set up and connected Power on the car engine, the device will be on auto and will start recording. The charging indicator will be on and the recording indicator twinkles. Power off the engine and the video will be saved before the device is switched off. The video will be saved partly on the SD/TF card. When the SD/ TF card is full, the device will cover the files which have been recorded earlier. Note: Recording time can be set in the menu. This has 2/3/5 min as options. The video file taken by the camera will be saved in the DCIMA folder of SD/TF card. If the cycle recording time is off, when the SD/TF card is full, the device will stop recording. 2. Recording manually Keep pressing the Power button for 3 seconds, this turns the camera on and the recording starts automatically. The recording indicator will be on and twinkles. To turn off keep pressing the Power button for 3 seconds again and the device will save the file and turn off. 3. Photo In standby mode, short press the Mode button to enter into the photo mode. At the top left corner of screen, the Recording icon will change into the Photo icon. Short press the OK button to take photos. Short press the Mode button twice will then can switch to the Recording mode. 4. Motion detection In standby mode, keep pressing UP. The motion detection will be on. When something is moving at the front of camera, the device will start recording automatically. If nothing is moving for 5 seconds, the device will stop recording. Press the Up button for 3 seconds when the device is not 05 recording and the motion detection will be switched off

7 5. G-sensor The device built-in G-sensor, if there is a serious vehicle collision the device will lock the video file which starts 10 seconds before the accident and end 2/3/5 minutes after the accident, meanwhile the bottom right corner will display the lock icon. The locked video will be saved as a special file which won t be covered by cycle recording. Note: The locked video file name ZWXXXX, general video name AWXXXX. G-sensor supports sensitivity adjustment, can be set according to actual demand. 6. Date and time set In standby mode, short press the menu button to enter into the system setting menu. Short press the UP/DOWN and move the cursor to make a date/time setting, then short press OK to confirm the setting. Note: In order to correctly record the date and time of any accident, please set the correct date and time before using this device. 7. Flash Disk Connect the camera to a computer using a USB cable. The camera LCD screen will show disk, camera, charge for options, short press UP/DOWN button and choose disk option, short press OK to confirm and enter into U Flash disk. 8. Playback In standby mode, short press the mode button twice to switch to playback mode. Short press the UP/DOWN button to find the file which needs to playback, short press the OK button to play it. Short press the Mode button again to exit playback mode. 06

8 Product Specifications Built-in Image Sensor Video Resolution CMOS FHD 1920x1080, HD 1280x720, VGA 640x480 Video Compression H.264 Video Format AVI Photo Format Storage Temperature Operational Temperature Operational Humidity SD/TF Card JPEG -30C - 70C 0C - 50C 15-65% RH Supports sizes up to 32GB Standard Voltage DC 5V 07

9 08

10 JD Williams Ltd.