Features. Parts Supplied. Parts not Supplied. Tools Required. ADC780 Series Indoor/Outdoor Vandal-Resistant Cameras. Installation and Setup Guide

Size: px

Start display at page:

Download "Features. Parts Supplied. Parts not Supplied. Tools Required. ADC780 Series Indoor/Outdoor Vandal-Resistant Cameras. Installation and Setup Guide"

Loraine Baldwin
5 years ago
Views:

1 ADC780 Series Indoor/Outdoor Vandal-Resistant Cameras Installation and Setup Guide Features Adjustable camera mount Indoor/Outdoor installation (except flush mount) ¾- and ½-inch conduit holes 24Vac hookup 2.6 6mm variable focal color camera with dc auto-iris adjustment Corner Mount Surface Mount The ADC780 series camera is for use in areas subject to vandalism such as subway stations, parking garages, prisons, police stations, corridors, supermarkets, and elevators. This camera, which comes in NTSC and PAL versions: Is contained in a cast aluminum housing with a polycarbonate window or dome. Three versions are offered: corner, flush, or surface mount. Has 480 lines of resolution to produce a sharp picture with true color and has a 2.6 6mm variable focal auto iris lens. Is protected by tamper-resistant hardware. Meets weather resistance standards: Surface Mount: NEMA 4, IP43 Corner Mount: NEMA 3R, IP43 Flush Mount: NEMA 1, IP40. Outdoor Applications Flush Mount Except when used in the flush mount, the camera can be mounted outdoors using an optional heater and thermostat that maintains the operating temperature between 40 C to +50 C. Parts Supplied Caution: Installation should be performed by qualified service personnel and in accordance with all local and federal electrical and building codes. Housing and associated hardware Mounting screws (4) Anchors, plastic (4) Screws, M6x35 (4) Washers, metal (4) O-rings, rubber (4) Desiccant (for corner mount, surface mount) Mounting Plate (for flush mount, surface mount) Screws, M4 x 8 pan head (4) flush and surface mounts only (for connection to electrical box mounting plate) Parts not Supplied Teflon plumbers tape UL-listed electrical tape Silicone caulk (for corner and surface mounts only) Threaded conduit IMPORTANT! Threaded rigid type conduit must be used for the corner and surface mount versions. Tools Required Torx wrench Small Phillips screwdriver Small slotted screwdriver 2005 Sensormatic Electronics Corp. INSTALLATION AND SETUP GUIDE 1 of 11

2 Corner Mount Installation 1. Loosen (DO NOT REMOVE) four captive Torx screws to remove the cover from enclosure. 3. Using the four mounting screws, attach the enclosure to the corner. Use Teflon tape to wrap the ends of the conduit before connecting it to the enclosure. M4 Plastic Anchors (4x) Rubber Washers (4x) 2. Prepare the four mounting screws. In extreme environments: Wrap the screw head in Teflon tape with the tape going ¼ inch down the body of the screw (A) and insert the washer and O- ring (B). Otherwise, just use the washer and O-ring (B). The O-ring goes on last. A B M6x35 Screws (4x) Teflon Tape INSTALLATION AND SETUP GUIDE 2 of 11

3 4. If using the camera outdoors, see Heater Installation, page Run 24vac and video cables to the enclosure. Connect cables where shown and apply power to the camera. Video Connection AC Camera Connection AC Terminal Block 7. Swivel the camera to adjust the ac phase control on the edge of the bottom board. 8. Select DIP switch settings (page 8). 9. Holding the yoke (not the camera lens barrel), swivel the camera to the desired view. Caution: DO NOT point the camera directly at the sun s path. 10. Adjust zoom and focus arms on the lens barrel to the desired setting and tighten them in place. 11. Tighten the two yoke screws. 12. If the humidity is high at the time of installation, place the bag of desiccant inside the enclosure. 13. Reattach the cover on the enclosure using the four Torx screws. 14. Place a bead of Silicone caulk everywhere where the corner mount meets the wall. 6. Holding the yoke (not the camera lens barrel), swivel the camera to adjust (using a small screwdriver) the auto-iris level control on the edge of the top board. Auto-Iris Level Adjustment Focus Zoom DIP Switch Swivel camera holding yoke AC Phase Adjustment Yoke Screws (2x) INSTALLATION AND SETUP GUIDE 3 of 11

4 Flush Mount Installation (In a wall or ceiling) 1. Loosen (DO NOT REMOVE) four captive Torx screws to remove the cover from enclosure. 3. Run 24vac and video cables through the opening in the ceiling. Then attach the enclosure to the gasket using screws shown. Apply power to the camera. Rubber Washers (2x) 2. Using the mounting plate as a template, cut a round opening in the wall or ceiling. Then, using the four anchors and screws supplied, center the gasket over the opening and attach it to the ceiling. M4 x 8 Pan Head Screws (2x) 4. Holding the yoke (not the camera lens barrel), swivel the camera to adjust (using a small screwdriver) the auto-iris level control on the edge of the top board. FC1 M4 x 20 Flat Head Screws (4x) M4 Plastic Anchors (4x) 5. Swivel the camera to adjust the ac phase control on the edge of the bottom board. 6. Select DIP switch settings (page 8). 7. Holding the yoke (not the camera lens barrel), swivel the camera to the desired view. Caution: DO NOT point the camera directly at the sun s path. 8. Adjust zoom and focus arms on the lens barrel to the desired setting and tighten them in place. 9. Tighten the two yoke screws and reattach the cover on the enclosure using the four Torx screws. INSTALLATION AND SETUP GUIDE 4 of 11

5 Surface Mount Installation 1. Loosen (DO NOT REMOVE) four captive Torx screws to remove the cover from enclosure. 4. If connecting to an electrical box, see Electrical Box Attachment, page 5. If using the camera outdoors, see Heater Installation, page 7. If humidity is a factor, see Heater/Fan installation, page Run 24vac and video cables to the enclosure. Connect cables where shown and apply power to the camera. Video Connection AC Terminal Block 2. Prepare the four mounting screws. In extreme environments: Wrap the screw head in Teflon tape with the tape going ¼ inch down the body of the screw (A) and insert the washer and O- ring (B). Otherwise, just use the washer and O-ring (B). The O-ring goes on last. A B 6. Holding the yoke (not the camera lens barrel), swivel the camera to adjust (using a small screwdriver) the auto-iris level control on the edge of the top board. Auto-Iris Level Adjustment Focus Zoom AC Camera Connection DIP Switch 3. Using the four mounting screws, attach the enclosure to the ceiling. Use Teflon tape to wrap the ends of the conduit before connecting it to the enclosure. Swivel camera holding yoke AC Phase Adjustment Yoke Screws (2x) Teflon Tape Plastic Anchors (4x) Screw Assembly (4x) INSTALLATION AND SETUP GUIDE 5 of 11

6 7. Swivel the camera to adjust the ac phase control on the edge of the bottom board. 8. Select DIP switch settings (page 8). 9. Holding the yoke (not the camera lens barrel), swivel the camera to the desired view. Caution: DO NOT point the camera directly at the sun s path. 10. Adjust zoom and focus arms on the lens barrel to the desired setting and tighten them in place. 11. Tighten the two yoke screws. 12. If the humidity is high at the time of installation, place the bag of desiccant inside the enclosure. 13. Reattach the cover on the enclosure using the four Torx screws. 14. Place a bead of Silicone caulk everywhere where the surface mount meets the wall. Electrical Box Attachment Flush Mount 1. Attach the mounting plate to the electrical box using four 8-32 screws shown. 2. Attach the enclosure to the mounting plate using four M4 x 8 screws. Note: Due to mounting hole locations on the cover plate, the enclosure will be oriented 45 to the electrical box. Electrical Box Cover Plate 8-32 x 0.75 Flat Head Screws (4x) M4 x 8 Pan Head Screws (4x) Surface Mount Connect enclosure to an electrical box using screws shown x 0.75 Flat Head Screws (4x) Electrical Box Cover Plate M4 x 8 Pan Head Screws (4x) INSTALLATION AND SETUP GUIDE 6 of 11

7 Heater Installation Corner Mount Remove the ac terminal block and wiring to the AC camera connection and replace it with the thermostat PC board and heater element. Each component is held in place by two screws. For wiring details, see ac/heater wiring diagram on page 8. Heater/Fan Installation (Surface Mount only) Remove the ac terminal block and wiring to the AC camera connection and replace it with the thermostat PC board and the heater/fan assembly. Each component is held in place by two screws. For wiring details, see ac/heater/fan wiring diagram on page 8. AC Camera Connection AC Terminal Block Surface Mount Remove the ac terminal block and wiring to the AC camera connection and replace it with the thermostat PC board and heater element. Each component is held in place by two screws. For wiring details, see ac/heater wiring diagram on page 8. AC Terminal Block Thermostat PC Board Heater Element AC Camera Connection Heater Element Thermostat PC Board INSTALLATION AND SETUP GUIDE 7 of 11

8 DIP Switch Default Settings 1. Automatic White Balance (On) 2. Gamma (On) 3. Automatic Gain Control (On) 4. Electronic Sensitivity Control (Off) 5. Back Light Compensation (Off) 6. Flicker Less (On) 7. AE (On) 8. Not Used (Don t Care) OFF AC/Heater/Fan Wiring Diagram (Surface Mount only) Note: Red wire from the fan goes to the J3 terminal marked +. AC In and AC to the Camera both connect to the J1 terminal. SW1 J2 J1 J SW1 (Thermostat) 12Vac Reg. 24Vac Reg. AC/Heater Wiring Diagram (Corner Mount or Surface Mount only) J2 J1 J3 Heater AC In AC to Camera + Fan J3 J1 J2 Heater SW1 AC to Camera J3 J1 SW1 (Thermostat) J2 AC In INSTALLATION AND SETUP GUIDE 8 of 11

9 Dimensions Corner Mount Flush Mount 91.5mm 3.6" 120.0mm 4.72" 124.2mm 4.9" PT 1/2" 86.0mm 3.39" 75mm 2.95" PT 3/4" 104.6mm 4.12" 120mm 4.73" 100mm 3.94" 85.0mm 3.35" 120.0mm 4.72" 52.5mm 2.07" 40.0mm 1.57" Surface Mount 91.5mm 3.60" 120.0mm 4.72" 86.0mm 3.39" 120.0mm 4.72" 86mm 3.39" INSTALLATION AND SETUP GUIDE 9 of 11

10 Specifications Models NTSC ADC780CM-24...Corner Mount ADC780SD Surface Mount ADC780FD-24...Flush Mount PAL ADC780CM-24X...Corner Mount ADC780SD-24X... Surface Mount ADC780FD-24X...Flush Mount Electrical Power input*...24vac (+20%, 15%) 60Hz NTSC 50Hz PAL Power consumption...3w Connectors Input power...screw terminal block Composite video...bnc on cord Controls AES...On/Off AGC...On/Off Synchronization...Line lock w/phase adjust. DC iris...level control Environmental Operating temp. (no heater) C to +50 C ( 14 F to +122 F) Operating temp. (with heater) C to +50 C ( 40 F to +122 F) Humidity...90% non-condensing Storage temp C to +60 C ( 4 F to +140 F) Mechanical Dimensions... (see page 9) Weight... Flush Mount: 450g (1 lbs) Surface Mount: 590g (1.3 lbs) Corner Mount: 590g (1.3 lbs) Color... Light beige Operational Imager... ¼" interline transfer CCD Video output Vp-p / 75-ohm composite Active pixel count NTSC (H) x 494 (V) PAL (H) x 582 (V) Lens mm variable focal, auto iris lens Sync system... Line lock Minimum scene illumination Lux at F1.4 Horizontal resolution TV line Light compensation modes... Auto. electronic shutter On/Off (NTSC 1/60 1/100,000 sec) (PAL 1/50 1/100,000 sec) Auto Iris Drive... DC Back light Compensation... On/Off selectable Synchronization modes... Line lock with phase adjustment White balance... Automatic Geometric distortion... None S/N ratio... 50dB * North America: Listed Class 2 power supply required. European Union: Certified limited power source required. INSTALLATION AND SETUP GUIDE 10 of 11

11 Regulatory Compliance REG ID: SV ALM-C SV ALM-W SV ALM-F Emissions... FCC part 15 Class A CE: EN55022 ICES-003 Immunity... CE: EN CE: EN Safety...UL1950 CSA C22.2 No. 950 EN60950 Weather resistance: Surface mount... NEMA 4, IP43 Corner mount... NEMA 3R, IP43 Flush mount... NEMA 1, IP40 Impact resistance... ASTM D A FCC COMPLIANCE: This equipment complies with Part 15 of the FCC rules for intentional radiators and Class A digital devices when installed and used in accordance with the instruction manual. Following these rules provides reasonable protection against harmful interference from equipment operated in a commercial area. This equipment should not be installed in a residential area as it can radiate radio frequency energy that could interfere with radio communications, a situation the user would have to fix at their own expense. CISPR 22 WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. EQUIPMENT MODIFICATION CAUTION: Equipment changes or modifications not expressly approved by Sensormatic Electronics Corporation, the party responsible for FCC compliance, could void the user's authority to operate the equipment and could create a hazardous condition. Other Declarations WARRANTY DISCLAIMER: Sensormatic Electronics Corporation makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, Sensormatic Electronics Corporation reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of Sensormatic Electronics Corporation to notify any person of such revision or changes. LIMITED RIGHTS NOTICE: For units of the Department of Defense, all documentation and manuals were developed at private expense and no part of it was developed using Government Funds. The restrictions governing the use and disclosure of technical data marked with this legend are set forth in the definition of limited rights in paragraph (a) (15) of the clause of DFARS Unpublished - rights reserved under the Copyright Laws of the United States. TRADEMARK NOTICE: American Dynamics, and the American Dynamics logo are registered trademarks of Sensormatic Electronics Corporation. Other product names (if any) mentioned herein may be trademarks or registered trademarks of Sensormatic or other companies. No part of this guide may be reproduced in any form without written permission from Sensormatic Electronics Corporation. RLJ 02/2005 INSTALLATION AND SETUP GUIDE 11 of 11

Black & White Camera Kit with Multiplexer Video Surveillance System

1 cam Video S equ en ce C all C a mer a Black & White Camera Kit with Multiplexer Video Surveillance System Installation and Setup Guide Cameras (4) Monitor RABW4MUX Function Zoom Main Monitor Line Tape