TopConsole system TP. Combination options 1-part 2-part 3-part. System accessories Page 537 Monitors, keyboards From page 796 Climate control Page 389

Transcription

1 opconsole system P System accessories Page 537 Monitors, keyboards From page 796 Climate control Page 389 Enclosure: Sheet steel 1.5 mm Door and console cover: Sheet steel, 2.0 mm, all-round foamed-in PU seal Mounting plate: Sheet steel 2.5 mm Surface finish: Dipcoat-primed, powdercoated on the outside, textured paint Mounting plate zinc-coated on bottom part Console Enclosure Cover hinged at bottom, including cover retainer Open base for individual cable entry Console, deep Enclosure Front cover hinged at bottom, including cover retainer Rear door, hinged at bottom Open base for individual cable entry Pedestal Enclosure open at top Door or double door with locking rod (with depth 400 mm at the front, with depth 500 mm at the front and rear) Depth-adjustable mounting plate (with depth 500 mm) Open base for individual cable entry Also required: Gland plates, see page 560. B Colour: RAL 7035 Protection category: IP 55 to IEC , complies with NEMA 12 (provided suitable gland plates are selected) Desk section Enclosure Cover hinged, 2 stays with automatic locking and unlocking Opening for running cables into the enclosure base Approvals: CE UL cul Detailed drawings: Available on the Internet. Photo shows a configuration example with equipment not included in the scope supply. Combination options 1-part 3-part Consoles Base/plinth 122 Rittal Catalogue 33/Enclosures

2 opconsole system P 600 mm wide Configuration 3-part 1-part Depth pedestal in mm Consoles 700 mm high 700 Page Depth () mm 240 Model No. P Consoles 540/730 mm high with enlarged installation depth Page Depth () mm Model No. P Partial mounting plate Rail for interior installation Width 200 mm ) 638 Width 500 mm ) 638 For width For height Page Depth () mm Model No. P Rail for interior installation For width Strengthener rim panel for pedestal Page Depth () mm Model No. P Base/plinth components front and rear eight 100 mm 1 set eight 200 mm 1 set eight 100 mm 1 set Base/plinth trim panels, side eight 200 mm 1 set Cross member, adjustable part Gland plates Rail for interior installation For height In the depth Punched rail 18 x 38 mm In the depth Support strips In the depth For door Support strips For door Cable clamp rail Wiring plan pocket ) Configuration examples and further details the accessories required may be found on the Internet. Rittal Catalogue 33/Enclosures 123

3 opconsole system P 800 mm wide Configuration 3-part 1-part Depth pedestal in mm Consoles 700 mm high 700 Page Depth () mm 240 Model No. P Consoles 540/730 mm high with enlarged installation depth Page Depth () mm Model No. P Partial mounting plate Rail for interior installation Width 200 mm ) 638 Width 500 mm ) 638 Width 700 mm ) 638 For width For height Page Depth () mm Model No. P Rail for interior installation For width Strengthener rim panel for pedestal Page Depth () mm Model No. P Base/plinth components eight 100 mm 1 set front and rear eight 200 mm 1 set Base/plinth trim panels, eight 100 mm 1 set side eight 200 mm 1 set Cross member, adjustable part Gland plates Rail for interior installation For height In the depth Punched rail 18 x 38 mm In the depth Support strips In the depth For door Support strips For door Cable clamp rail Wiring plan pocket ) Configuration examples and further details the accessories required may be found on the Internet. 124 Rittal Catalogue 33/Enclosures

4 opconsole system P 1200 mm wide Configuration 3-part 1-part Depth pedestal in mm Consoles 700 mm high 700 Page Depth () mm 240 Model No. P Consoles 540/730 mm high with enlarged installation depth Page Depth () mm Model No. P ) ) Partial mounting plate Rail for interior installation Width 200 mm ) 638 Width 500 mm ) 638 Width 700 mm ) 638 For width For height Page Depth () mm Model No. P Rail for interior installation For width rim panel for pedestal Page Depth () mm Model No. P Base/plinth components eight 100 mm 1 set front and rear eight 200 mm 1 set Base/plinth trim panels, eight 100 mm 1 set side eight 200 mm 1 set Cross member, adjustable part Gland plates 2) Rail for interior installation For height In the depth Punched rail 18 x 38 mm In the depth Support strips In the depth For door Support strips For door Cable clamp rail Wiring plan pocket ) Configuration examples and further details the accessories required may be found on the Internet. 2) With the two-door pedestal, the base opening is divided in two, and two sets gland plates are required! 3) Extended delivery times. Rittal Catalogue 33/Enclosures 125

5 opconsole system P 1600 mm wide Configuration 3-part 1-part Depth pedestal in mm Consoles 700 mm high 700 Page Depth () mm 240 Model No. P Consoles 540/730 mm high with enlarged installation depth Page Depth () mm Model No. P Width 200 mm ) 638 Partial mounting plate Width 500 mm ) 638 Width 700 mm ) 638 Rail for interior installation For height Page Depth () mm Model No. P Rail for interior installation For width rim panel for pedestal Page Depth () mm Model No. P Base/plinth components eight 100 mm 1 set front and rear eight 200 mm 1 set Base/plinth trim panels, eight 100 mm 1 set side eight 200 mm 1 set Cross member, adjustable part Gland plates 2) Rail for interior installation For height In the depth Punched rail 18 x 38 mm In the depth Support strips In the depth Support strips For door Cable clamp rail Width 800 mm Wiring plan pocket ) Configuration examples and further details the accessories required may be found on the Internet. 2) With the two-door pedestal, the base opening is divided in two, and two sets gland plates are required! 126 Rittal Catalogue 33/Enclosures

6 opconsole system P rim panel for pedestal for covering the complete top opening when using the pedestal on its own. Sheet steel Surface finish: extured paint Colour: RAL 7035 Protection category: IP 55 to IEC , complies with NEMA 12. Assembly parts. For pedestal Width mm Depth mm Model No Strengthener for desk unit, rear with hinged cover Suitable for mounting operating housings using CP-L enclosure attachment, Ø 130 mm, CP , see page 155 CP-XL enclosure attachment, round CP , see page 163 ousing couplings CP-XL for desk mounting, CP , see page 166 Easily screw-fastened to the base the desk unit. Connection hole pattern for CP support arm systems in the centre as standard; other positions can be accommodated by drilling extra holes. Mounting cut-out required in the cover the desk units, mounting cut-outs to match the various support arm systems. Sheet steel Assembly parts. For width mm Model No. P Mounting cut-outs for the covers the desk units for external mounting CP Ø 9 Max. Ø 70 mm /792 Ø 82 1 for external mounting CP Ø Ø for external mounting CP Ø 9 = = Rittal Catalogue 33/Enclosures 127

7 One-piece consoles P System accessories Page 537 Monitors, keyboards From page 796 Climate control Page 389 One-piece consoles AP stainless steel Page 192 Enclosure: Sheet steel 1.5 mm Door and console cover: Sheet steel, 2.0 mm, all-round foamed-in PU seal Mounting plate: Sheet steel 3.0 mm Lock cover: Plastic, self-extinguishing Surface finish: Enclosure, cover and door: Dipcoat-primed, powdercoated on the outside, textured paint Mounting plate: Zinc-plated Colour: RAL 7035 Protection category: IP 55 to IEC , complies with NEMA 12 (provided suitable gland plates are selected). Enclosure, solid back and sides Door or double door at front, with locking rod Mounting plate Cover hinged at rear, 2 stays with automatic locking and unlocking Open base for individual cable entry Also required: Gland plates, see page Detailed drawings: Available on the Internet. B F G Width (B) mm Page Depth () mm Bottom op Mounting plate width (F) mm Mounting plate height (G) mm Model No. P Door(s) Base/plinth Components front and rear eight 100 mm 1 set eight 200 mm 1 set rim panels, sides eight 100 mm 1 set eight 200 mm 1 set Cross member, adjustable Gland plates 1) Rail for interior installation 1-part For enclosures For cover Punched section For enclosures with mounting flange, For cover x 73 mm For door Punched rail 18 x 38 mm For enclosures Cable clamp rail Wiring plan pocket ) With the two-door variant, the base opening is divided in two, and two sets gland plates are required! Rittal Catalogue 33/Enclosures

8 Universal consoles P System accessories Page 537 Monitors, keyboards From page 796 Climate control Page 389 Enclosure, gland plates: Sheet steel 1.5 mm Doors: Sheet steel 2.0 mm Mounting plate: Sheet steel 3.0 mm Surface finish: Enclosure and doors: Dipcoat-primed, powdercoated on the outside, textured paint Mounting plate and gland plates: Zinc-plated Colour: RAL 7035 Protection category: IP 55 to IEC , complies with NEMA 12. With a short bottom door (P ), the drawer or desk section (see below) should be fitted in order to preserve the protection category. Enclosure with doors Mounting plate Gland plates Note: op door with studs left and right for installing vertical perforated mounting strips SZ and horizontal support strips SZ to be mounted on top (see page 615/614). Approvals: UL CSA ÜV Germanischer Lloyd Russian Maritime Register Shipping Lloyds Register Shipping VDE Detailed drawings: Available on the Internet. Photo shows a configuration example with equipment not included in the scope supply. F B G with short front door with tall front door Page Width (B) mm Depth () mm Bottom op Mounting plate width (F) mm Mounting plate height (G) mm Model No. P Weight (kg) Also required Desk section Drawer for keyboard ) Base/plinth eight 100 mm eight 200 mm Cross member, adjustable Perforated mounting strip Support strips Cable clamp rail ) Only suitable for installation without a mounting plate. Rittal Catalogue 33/Enclosures 129