CLS Atmosphere LED-panel

Transcription

1 INDEX Index 2 Introduction Included items Optional accessories Safety information 4 Installation REVO Colour Flow 5 LDC connectioncable for the REVO Colour Flow 6 Assemble a REVO Colour Flow connectioncable 6 Wiring diagram 7 Replace lenses 9 Measurements 10 Specifications 11 List of symbols 12 Version 1.0 June CLS-LED BV. All rights reserved. Information subject to change without notice, CLS-LED BV and all affiliated companies disclaim liability for injury, damage direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this manual. No part of this manual may be reproduced, in any form or by any means, without permission in writing from CLS-LED BV. Other legal information can be found in our General conditions to be found on the back of your CLS-LED BV invoice or on our website /Conditions.pdf

2 INTRODUCTION CLS s brand new REVO Colour Flow product line belongs to a revolutionary flexible new IP67 range of products that can be used for an enormous amount of applications. Available in a RGBW & RGBA version. The REVO is designed in The Netherlands by a team of architectural specialists. Included items The is shipped in one package containing the following items: 1 x 1 x manual Optional accessories CLS REVO lens kit superspot 8º 8 pcs of lenses CLS REVO lens kit spot 12 8 pcs of lenses CLS REVO lens kit medium flood 0 8 pcs of lenses CLS REVO lens kit wide flood 54 8 pcs of lenses CLS REVO lens kit elliptical 12x46 8 pcs of lenses CLS mold set, straight 8-26mm CLS LDC-41 DMX LED dimmer 4 channels 0.5-1A per channel CLS Zense DMX controller + built in 4 Amp RGB dimmer connector male connector female shortcircuit connector cable, per metre connectioncable, IP67, 2 meters complete connectioncable, IP67, 4 meters complete connectioncable, IP67, 8 meters complete CLS BT20.24 LED power supply 24VDC 20VA VAC CLS BT45.24 LED power supply 24VDC 45VA VAC CLS BT75.24 LED power supply 24VDC 75VA VAC CLS BT LED power supply 24VDC 120VA VAC CLS BT LED power supply 24VDC 240VA VAC CLS BT75.48 LED power supply 48VDC 75VA VAC CLS BT LED power supply 48VDC 120VA VAC CLS BT LED power supply 48VDC 240VA VAC Note: It is important to read this manual before you install this product. SAFETY INFORMATION Warning! This product is for professional use only, not for domestic use. Read this manual before powering up or installing the CLS REVO. Follow the instructions listed below and observe all warnings in this manual. Protection from electric shock Disconnect the power supply from AC power before installing, dismounting or maintaining the unit. Make sure all connectors are connected properly. Use only a source of AC power that complies with local building and electrical codes and has both overload and ground-fault protection. Refer all service to a qualified technician. Protection from burns and fire Provide a clearance of at least 50mm around the unit. Do not install this product near a heat source. Do not install this product in a corrosive, flammable or explosive area. Do not modify this product, or install other than genuine parts. Do not operate this product if the ambient temperature exceeds 40 ºC. Do not stare into the LED, this can cause damage to the eyes. Protection from injury due to falls Verify that all covers and mounting hardware are securely fastened. Block the access below the work area whenever installing or removing the unit. WARNING The CLS REVO is an IP67 outdoor unit, but can under no circumstances be used under water! The warranty on these armatures for outdoor use, only applies with a correct use of the CLS mold set (article no )

3 Installation REVO Colour Flow LDC connectioncable for the revo colour flow 1 2 b mm a b 6 mm # CLS mold set Male connector Take a REVO Colour Flow connectioncable and cut of the male connector. 2. Strip the connection cable harness for 50 mm. b. Strip the exposed wires for 6 mm.. The LDC connectioncable for the REVO Colour Flow is ready to be used Assemble a revo colour flow connection cable This instruction shows how to assemble the wiring in a REVO Colour Flow connector. 1. The can be installed by using the mounting hole. Drill a hole to secure it in the wall, floor, ceiling, etc. Drill a second hole for the connectioncables if the cable connection is indoors. For all situations where a OUTDOOR connection needs to be made between the cable of the first REVO and the connection cable of the DMX dimmer. WARNING ALWAYS USE THE CLS MOLD SET. OTHERWISE THERE WILL BE NO WARRANTY ON WATER OR MOISTURE RELATED PROBLEMS! Skip step 2 and if the cable connection is indoors. 2. Use the mold set to make the connection waterproof. Place the cable connection in the bottom of the mold set. a. Press the cover on the bottom of the mold set. b. Poor the substance through the hole of the cover. Make sure you completely fill the mold set.. Seal the mold set by placing the lid on top of the mold set. 4. See the next page how to connect the on a LED Dimmer with DMX controller. 5. Adjust the to the preferred position by turning the unit towards or away from the wall. 6. The is ready to use. 1 Cable connector male 2 Cable connector female Pin Assignment back view Pin Assignment back view 4 20 mm b mm 1. Wiring for REVO Colour Flow male connector: 1 - red wire 4 - white wire 2 - Green 5 - black wire - blue 2. Wiring for REVO Colour Flow female connector: 1 - red wire 4 - white wire 2 - Green 5 - black wire - blue. Take the REVO Colour Flow cable and strip the cable harness for 20 mm. b. Strip the exposed wires for mm. 4. Solder the wires in the connector and assemble the connector back in the right order, as show in the picture

4 WIring diagram LDC-41 DMX LED dimmer, Dimmable * Make sure the LDC-41 is configured to max. 700mA * Use the Shortcircuit connector to close the installation CLS LDC-41 DMX LED dimmer 4 channels 0.5-1A per channel # CLS LDC connectioncable for the REVO Colour Flow RGBA or RGBW # R-6-X-XX-X Red wire Green wire Blue wire White wire Black wire 170 mm (h) CLS Zense DMX controller + built in 4 amp RGB dimmer # CLS BT power supply 24V/48V connectioncable, complete IP67 # 11078X 8 mm (h) (d) 8 mm (w) RJ45 (UTP) cable Min. 1 pcs and max. 1 pcs of REVO Colour Flow on a BT LED power supply Min. 1 pcs and max. 2 pcs of REVO Colour Flow on a BT LED power supply Min. 1 pcs and max. pcs of REVO Colour Flow on a BT LED power supply Min. 1 pcs and max. pcs of REVO Colour Flow on a BT LED power supply Min. 1 pcs and max. pcs of REVO Colour Flow on a BT LED power supply Min. 4 pcs and max. 4 pcs of REVO Colour Flow on a BT LED power supply Min. 4 pcs and max. 6 pcs of REVO Colour Flow on a BT LED power supply Min. 4 pcs and max. 6 pcs of REVO Colour Flow on a BT LED power supply Shortcircuit connector #

5 WARNING ATTENTION! Make sure that the rubber sealing is correctly in place! measurements 1 mm REPLACE LENSES This section shows how to replace the lenses inside the. 40 mm 1 2 Cover plate Glass frame Lensholder ø 10 mm 4 5 Cover plate Glass mm frame Lensholder mm 1. The. 2. Disassemble the cover plate by loosening the 4 screws. 170 mm. Carefully lift the items out of the unit and take the lens holder. 4. Press the 8 lenses out of the lens holder and replace them with the desired lenses. Make sure all the lenses are in the same direction as shown in picture Now carefully place the items in the unit in the right order as shown in picture. 6. Tighten the screws by order (crosswise) as shown in picture 6 on the cover plate to keep the REVO waterproof. The is ready to be used with the desired lenses. 70 mm 10 mm

6 list of symbols Technical Specifications LED: 8 x Luxeon / Cree Available colours: RGBW and RGBA Lenses: Spot, medium flood, wide flood and elliptical Power supply: 700mA Power consumption: 18 Watt Housing: Anodised aluminum Weight: 1,9 kg IP value: IP67 Measurements: 170 x 10 x (hxwxd) Ambient temperature: -0º C till +40º C Protection class One, two or three Application area Indoor or outdoor Application area Floor, wall or ceiling Swivel Fixture is horizontally rotatable, indicated in degrees Swivel Fixture is vertically rotatable, indicated in degrees 600K RGB 4000K RGB-W 000K RGB-A 2700K Colour Available colours; Amber, blue, red or green Colour temperature White in different Kelvin values; Cold white, neutral white, warm white or extra warm white Colour changing RGB, RGB-W or RGB-A Curve Minimal bending curve in centimeters Cutting length Indicated by the cutting marks Multiple connection Daisychain connectivity LED pitch Pitch between the LEDs in millimeters Installation depth In centimeters 100~240 VAC 100~240 VDC 700 ma Power supply In VAC, VDC or milliampere Luxeon/Cree RGB-W RGB-A 700mA 18 Watt IP67 Anodised Aluminum 1,90 kg 54º 0º 12º 8º 12 x 46º 8 x 50 cm Mounting hole In centimeters Cable length Maximum cable attached to the fixture in centimeters 20 VA IP40 Watt Power consumption In VA or Watt IP value Ingress Protection classifies the degrees of protection provided against the intrusion of the product Driver Inclusive or exclusive Aluminum Brushed Housing Housing material Weight In grams/kilograms DMX channels Numbers of DMX channels on a product Pressure Maximum pressure on the fixture in kg/cm 2 DMX 512 DMX input Fixture works on DMX512 protocol Lifespan Of the light source in hours Combined product Compose your own fixture 54º 8º 12 x 50º Lenses Availble lenses, indicated in degrees Warranty years warranty on the product Luxeon 1 x LEDs Kind of LED used in the fixture Conformité Européenne CE marking for free marketability of industrial goods within the EU Plug & play Easy connection using the SmartConnect system A Energy label