GSM communicator G10D

Size: px
Start display at page:

Download "GSM communicator G10D"

Transcription

1 D (v.1.xx) USER MANUAL UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage:

2 Description The communicator G10D is designed to transmit messages from security control panel in secured object to an alarm receiving centre (ARC) and/or to a mobile/web application. Messages are transmitted using GPRS, SMS and DTMF tones via GSM network. GSM communicator compatible with Paradox, DSC, Caddx, Pyronix and other manufacturer control panels, reading messages directly from control panels DATA BUS. Features Connection Compatible with most control panels Connection to control panels via: o Data bus direct connection Communications Communication modes: o GPRS o DTMF tones o SMS Two SIM cards can be used for communication via primary and backup channels; If the GPRS connection with primary and backup servers will be lost, information can be sent in SMS messages; Mobile/Web application using a cloud service. Allowing user to remotely monitor and control the alarm system Event messages can be transmitted in Contact ID codes Event reporting via SMS messages to 4 different users in user customized SMS messages PING technology to detect communication problems Configuration Quick and easy configuration and firmware update Operating parameters and firmware version can be updated remotely Operating parameters are set with program G10config Inputs and outputs 1 Output controlled via: o Mobile/Web application o SMS o Internal events 2 Inputs, type: NC Trikdis 1

3 Content GSM communicator G10 Safety requirements... 2 Limitation of liability... 2 Operation description... 3 Technical specification... 3 Package content... 3 Module elements... 3 Description of terminals... 3 LED indication... 4 Installation steps... 4 Wiring diagrams... 4 Setting of operation parameters... 5 Protegus service... 9 Setting of operation parameters remotely Actions after sending an SMS message: Device firmware upgrade Remote firmware upgrade Remote output OUT1 status control Annex 1. SMS messages Safety requirements Please read this manual carefully before using the security communicator G10. Module G10D may only be installed and maintained by trained specialists with knowledge about operation of low voltage and signal transmission devices and their safety requirements. Module G10 should be mounted in places with restricted access and in safe distance from any sensitive electronic equipment. The device is not resistant to mechanical effects, dampness and hazardous chemical environment. Limitation of liability - When buying the Device, the Buyer agrees that the Device is a part of a security system of premises, which sends messages about security system status. The Device, when installed, does not diminish the probability of burglary, fire, intrusion or other breach of premises. - UAB TRIKDIS is not responsible for burglary, fire or any other breach of Buyer s and/or User s premises and is not liable for any direct or indirect damages incurred thereof. - When buying the Device, the Buyer agrees that the Device supplied by UAB TRIKDIS fully meets his requirements for intended use. - UAB TRIKIDIS provides no guarantees that the Device shall function as declared if the Device is installed and used not according to its original purpose, user manual and relevant electronic and technical conditions. - UAB TRIKDIS is in no way associated with GSM/GPRS/Internet service providers (operators), thus UAB TRIKDIS is in no way responsible for any defects in Device operation if they have occurred because of the loss of GSM/GPRS/Internet connection, or because of other defects in the service provider network. - UAB TRIKDIS has no control and is not responsible for the prices and marketing of network services provided by the GSM/GPRS/Internet service providers. - UAB TRIKDIS is not responsible if GSM/GPRS/Internet services are not provided to the Buyer and/or User of the Device or were cancelled and any direct or indirect damages were incurred thereof. - UAB TRIKDIS is not responsible for any direct or indirect damages incurred by the Buyer and/or User of the Device due to loss of electricity. - UAB TRIKDIS is not liable if Device firmware versions were not updated by the Buyer and/or the User on time. - User manual of the Device can contain technical inaccuracies, grammatical or typographical errors. UAB TRIKDIS reserves the right to correct, update and/or change information in the installation manual Trikdis 2

4 Operation description Module can receive messages from DSC, Caddx, Paradox, SECOLink or Pynonix security control panel data buses and transmits them to the monitoring station using the pre-set communication channel. Full list of control panels can be found in G10config. Module can send messages via the backup channel, if the communication via main channel fails. The second SIM card may be used for communication via the backup channel. Module may send information to the monitoring station using SMS messages if module loses GPRS connection with both servers. Module may send messages to set addressees about input IN1 and IN2 external circuit failures and restores. Module may periodically send PING signals to test connection. Messages may be sent via SMS messages to four mobile phones. Every security control panel messages is allocated a comprehensible SMS message text. Module output OUT1 status changes when connection with monitoring station server fails/restores or when module receives an SMS message to change the output status. Technical specification Parameter Power supply Used current Message encryption GSM modem frequencies Memory Inputs Output Setting parameters Workplace Measures Description direct 12,6 V ± 3 V ma (on standby), Up to 250 ma (while sending data) TRK_TCP or TRK_UDP protocols 850 / 900 / 1800 / 1900 MHz Up to 60 messages 2, NC type 1 OC type, commutating direct voltage of up to 30 V and current of up to 1 A Via USB port temperature from -10 C to 50 C, relative humidity up to 80 % when +20 C 65 x 79 x 25 mm Package content Module G10D Adhesive mounting tape (7 cm) 1 pc. 1 pc. Module elements GSM antenna SMA-F screw-up connector 2. Removable contact terminal block 3. USB port 4. LED indicators 5. Two holders for SIM cards 2 5 Description of terminals Terminal Description +E +12V power supply terminal COM Common terminal (negative) CLK Synchronising signal terminal DATA Data signal terminal IN1 1st input terminal (NC type) OUT1 Open-collector output terminal (null-negative) IN2 2nd input terminal (NC type) COM Common terminal (negative) MCI Will be used in the future Trikdis 3

5 LED indication LED indicator Status Description Green light Module is connected to GSM network Network denotes the Yellow light Message is being sent connection status with the Green flashing Connecting to GSM network GSM network Yellow flashing The amount of yellow flashes denotes GSM connection strength Green light Unsent messages in module memory Red light Sending messages fails Data denotes data exchange Green flashing Messages from security control panel are being received Red flashing frequently Incorrect module settings Red flashing SIM card error Power supply on, Green flashing Power denotes power supply Microprocessor is working status, microprocessor status Insufficient power supply voltage ( 11,5 V), microprocessor is Yellow flashing and programming mode working Green and yellow flashing in turns Programming mode on SIM1 SIM2 Yellow light Shows which SMS card is active Installation steps Configure communicator parameters before installation. For communicator configuration please refer to chapter Setting Operating Parameters. 2. Insert activated Standart SIM card(s) into the holder(s). Note: SIM card must be registered in GSM network and enabled mobile data communication service (if required). Ensure that the PIN code request is disabled (required for first time remote configuration). 3. Embed communicator into mounting case using fastening tape. 4. Connect the GSM antenna. 5. Following chapter Wiring diagrams connect a control panel, sensors and output connections. 6. Connect a DC power supply. 7. Check GSM signal strength according to light indication: Sufficient GSM signal strength is level 5 (five yellow flashes of indicator Network). If GSM signal is not sufficient, use another antenna type. 8. Check if the module sends messages according to its configuration: the messages must be sent and received at the specified IP address. If messages ar sent to a mobile phone, check if all SMS messages are received. Wiring diagrams Connection diagram for DSC Power Series security control panels PC1616, PC1832, PC1864 PC585, PC1565, PC5020. Connection diagram for Paradox security control panels SPECTRA SP5500, SP6000, SP7000, 1727, 1728, 1738, MAGELLAN MG5000, MG5050, DIGIPLEX EVO48, EVO192, EVO96, NE96, ESPRIT E55, 728ULT, 738ULT Trikdis 4

6 Connection diagram for Pyronix Matrix Series security control panels MATRIX 424, MATRIX 832, MATRIX 832+, MATRIX 6, MATRIX 816. Connection diagram for Caddx security control panels NX-4, NX-6, NX-8. Connection diagram for SECOLink security control panels PAS832 (communicator firmware must be at least G10D v1.4x or newer) Setting of operation parameters Module G10D operation parameters are set using G10config. Program can be found in website (USB drivers must be installed in the computer). 1. Connect the module G10D to a computer using a USB cable. a) Download the USB driver file USB_COM.inf for MS Windows OS from the website b) If the module is connected to a computer for the first time, MS Windows OS should open the window Found New Hardware Wizard for installing USB drivers. c) In the wizard window select the function Yes, this time only and press the button Next. d) When the window Please choose your search and installation options opens, press the button Browse and select the place where the file USB_COM.inf was saved. e) Follow the remaining wizard instructions to finish the USB driver installation. 2. Run G10config. 3. Select Connect in the menu. 4. Click Connect [F2/F8] a) Select the USB port to which the module is connected in the list Port. Note: the particular USB port to which the module is connected appears only when the two are connected. b) Select the desired working language in the list Language. Note: Indicator Power should flash green and yellow in turns when communicator G10D is connected to a computer. Connection status Connected should be displayed in the G10config status bar alongside the information about the connected communicator: Module type Device IMEI number Module serial number Trikdis 5

7 5. Click Read [F7]. Module firmware version a) Enter the access code (default 1234) when prompted and click OK. Note: Click Remember if you want the software to remember your access code. The prompt window will not appear next time. 6. Select Main in the menu and set the desired parameters: Object ID Field to enter the four-digit identification number; SIM card PIN code Field for SIM card PIN code. Leave the field empty if PIN code request is disabled; User code Field to enter the user code. Only those operation parameters that are allowed to be edited by the administrator can be edited when logging in with the user code; Admin code Field to enter the admin code. All operation parameters can be edited when logging in with the admin code. Also, possibilities for editing the operation parameters for those logging in with the user code may be limited; Panel type Select the control panel type to which the communicator is connected. Select INTERFACE C11, C14, CZ6 if module is connected to interface C11, C14 or CZ6; IN1 Choose 24h. zone from the list to send message Module events in a pre-set code if external input IN1 circuit is tampered with. Choose Backup mode to send control panel messages only when external input IN1 is broken; PGM Choose Remote control SMS to change module output status when module receives a control command via SMS message (see section Remote module control). Choose Lost Primary Channel for output status to switch to the opposite status if communication via the main channel fails. Choose Lost Secondary Channel for output status to switch to the opposite status if communication via the backup channel fails. Choose Lost Both channels for output status to switch to the opposite status if communication via both main and backup channels fails; GPRS PING time Module will send GPRS to receiver connection test signals PING in a specified frequency; CSD PING time Module will send CSD to receiver connection test signals PING in a specified frequency; Trikdis 6

8 SMS PING time Module will send SMS to receiver connection test signals PING in a specified frequency; Test time Module will send connection testing messages TEST to the monitoring panel in a specified frequency; Return to primary after Used if both communication channels to the monitoring panel are selected main and backup. Enter the time duration for sending messages via the backup communication channel, if the main communication channel fails. Backup reporting after... attempts Used if both connection channels to the monitoring panel are selected main and backup. Enter the number of times the module will try to send a message via the main communication channel and upon failure will send messages using the backup communication channel. 7. Enter parameters for communication with the monitoring station in GPRS reporting: Primary reporting Backup reporting Select the main communication channel via which the module will send messages to the monitoring panel: Choose GPRS_SIM1(2) and enter the IP address and the port number of the monitoring panel in fields Server IP1 address or Domain and Port. Choose DTMF_SIM1(2) and enter the PSTN receiver phone number in the field Tel.1 in order to send Contact ID messages in DTMF tones (only available in G10D v1.4x). Phone number is entered with the international country code, but without the + sign. Choose SMS_SIM1(2) and enter the monitoring station phone number in the field Tel.1 in order to send SMS messages with Contact ID event codes. Phone number is entered with the international country code, but without the + sign. If Protegus_SIM1(2) is selected, all needed fields in section Primary reporting are filled in automatically, Backup reporting is disabled. Select the backup communication channel via which the module will send messages if connection via the main channel is lost: Choose GPRS_SIM2 and enter the IP address and the port number of the monitoring panel in fields Server IP2 address or Domain and Port. Choose DTMF_SIM2 and enter the PSTN receiver phone number in the field Tel.2 in order to send Contact ID messages in DTMF tones (only available in G10D v1.4x). Phone number is entered with the international country code, but without the + sign. Choose SMS_SIM2 and enter the monitoring station phone number in the field Tel.2 in order to send SMS messages with Contact ID event codes. Phone number is entered with the international country code, but without the + sign. Second backup channel phone Monitoring station phone number to which SMS messages will be sent if modules loses GPRS connection with two servers. This option is available when both main and backup Trikdis 7

9 Protocol Encryption key channels are set for GPRS. Phone number is entered with the international country code, but without the + sign. Select the message encryption protocol from the list; Field to enter the six-digit encryption password. Password must match the decryption password entered in the reception software IPcom; IP addresses, port and phone number, encryption protocol and key, other parameters may only be submitted by the monitoring station manager APN1, APN2 User1, User2 Password1, Password2 DNS1, DNS2 GSM network operator access point name; Login for connecting to the GSM network; Password for connection to the GSM network; Server names of the domains; APN, user name, password and DNS values must be submitted by the GSM connection operator the SIM card was purchased from. Module events Module events after which a message will also be sent are listed in the table. Event code may be changed by clicking on Contact ID event code or Contact ID restore code and entering accurate values (to check whether entered values are accurate click OK). Module events E event description R event description SIM1 Communication started using the first SIM card SIM2 Communication started using the second SIM card TEST Periodic module Test message POWER Power supply lower than 11,5 V Power supply restored to 12,6 V TAMPER_1 External circuit of input IN1 is tampered with External circuit of input IN1 is restored after being tampered with TAMPER_2 External circuit of input IN2 is tampered with External circuit of input IN2 is restored after being tampered with 8. Enter parameters necessary for sending SMS messages to users in tab Text SMS reporting: Trikdis 8

10 Telephone Enter user phone numbers T1, T2, T3, T4 to which SMS messages will be sent. Phone numbers are entered with the international country code, but without the + sign; Name Select after which types of events a message will be sent to users: Alarm/Restore SMS messages about zone violations/restores (event codes E/R 1XX see Annex 1); Arm/Disarm SMS messages about arming/disarming the alarm (event codes E/R 4XX, see Annex 1); Troubles SMS messages about system operation failures (event codes E/R 3XX, see Annex 1); Tests System Test SMS messages (event code E 602, see Annex 1); SMS encoding Select the desired SMS encoding from the list; Send SMS Select All to send messages about all events in the security control panel; Select Only described to send messages about events that occur in described zones; Object ID Enter the object name which will be included into the SMS message text; Users Entries in the table are linked with the user codes that are used to arm/disarm the alarm system. Name of the user will be included in the SMS message, if the user arms/disarms the alarm system; Zones Entries in the table are linked with the protected zone events. Zone name specified in the table will be included in the SMS message, when zone is breached/restored. Partitions Entries in the table are linked with the partitions of the security system into several independently protected areas. Name of the breached/restored area as indicated in the table will be included in the SMS message. Save [F5] Restore [F11] Click to save values entered in G10config on the computer. A file with an extension.gst will be created and may be used in the future as a template to configure other modules Click to restore factory values of module G10D operation parameters. Click Confirm when prompted. 9. Click Write [F6] to save values entered in G10config fields to the module G10D. 10. Click Disconnect [F8] and unplug the USB cable. Protegus service Protegus service allows users to remotely monitor and control the communicator. After communicator G10 is set to work with Protegus service and connected to power supply, you can set that G10 communicator would use open collector output (PGM). The user can trigger the output to activate an input on the host panel to trigger a key-switch zone and arm/disarm the system. This feature can be set in your Protegus application. To set PGM for ARM/DISARM system follow these steps: 1. If you do not have Protegus service account you can create it by fill registration form here: a) To add the system to the Protegus, press Select system, next Add new system +, and enter required data, follow steps in pictures. G 10 does not have Servi ce code. b) Enter system name. c) Enter IMEI (from G10config status bar) Trikdis 9

11 f) Save the changes. d) Go to Settings tab. e) Tick "Arm/Disarm with PGM". Setting of operation parameters remotely Send an SMS message to the GSM number of the SIM card inserted into the module G10D in order to set operation parameters of the module remotely. Upon receiving an SMS message, module G10D will initiate a continuous GPRS connection session with IPcom. If the phone number of the authorised person was entered in the field Wireless programming phones in the field For connecting during the setting of operation parameters, the module will initiate a GPRS connection session only upon receiving an SMS message from that specific phone number. SMS message text (_refers to a space between words in an SMS message): CONNECTtarpas9874tarpasSERVER= tarpasPORT=1000tarpasAPN=tiekėjastarpasUSR=vardastarpasPSW=pswtarpasENCR=enc Explanation of SMS message text: CONNECT Start command; 9874 Enter the four-digit access code (default ); SERVER= SERVER= + enter the IP address of the computer with installed software IPcom; PORT=1000 PORT= + enter the serial port number of the program IPcom; APN= + enter the access point name (APN) of the GPRS network in which the APN=provider SIM card inserted into the communicator operates. Enter..._APN=_... if the network provider does not require an access point name; USR= + enter the login user name of the GPRS network in which the SIM card USR=name inserted into the communicator operates. Enter..._USR=_... if the network provider does not require an access point name; PSW= + enter the login password of the GPRS network in which the SIM card PSW=psw inserted into the communicator operates. Enter..._PSW=_... if the network provider does not require an access point name; ENCR=enc ENCR= + enter the six-digit message decryption password (default ). Actions after sending an SMS message: 1. Open IPcom and right-click on the identification number [Object ID] of the module whose parameters you wish to modify Trikdis 10

12 2. Left-click G10config next to the identification number. 3. Left-click Connect and Read in the G10config taskbar. GPRS connection status Connected will be displayed in the program status bar if GPRS connection session with module G10D is open. 4. Operation parameters of module G10D are set in the same way as connecting it using the USB cable (see section Setting operation parameters). 5. Once desired parameters are entered in G10config, click Write to save them to module G10D. Click Disconnect to end the GPRS connection session. Device firmware upgrade Previously purchased module software may be upgraded once the manufacturer updates module G10D with new operation features: 1. Download the newest GF10_vx.xx.prg file from 2. Connect module G10D to a computer, run G10config, open tab Update and select G10D_vx.xx.prg saved on a computer. 3. Click Start [F9]. Click Disconnect [F8] once the progress bar fills up. Disconnect the USB cable. 4. Reconnect the USB cable. Updating software takes about seconds. Wain until indicator Data stops flashing green and click Connect [F2] and Read [F7]. New module software version will be displayed in the G10config status bar. Remote firmware upgrade 1. Send an SMS message to the GSM number of the SIM card inserted into module G10D (for details see section Setting operation parameters remotely). 2. Open IPcom and right-click on the identification number [Object ID] of the module whose parameters you wish to modify. 3. Left-click Connect and Read in the G10config taskbar. GPRS connection status Connected will be displayed in the program status bar if GPRS connection session with module G10D is open. 4. Select tab Firmware in G10config. Click Browse and select file G10F_vx.xx.prg previously downloaded from website and saved on the computer. 5. Click Start to begin the update, which takes about seconds to complete. Progress will be displayed in the progress bar. Click Read once the progress bar fills up. New module G10D firmware version bill be displayed in the G10config status bar. 6. See section Setting operation parameters if you wish to view or edit operation parameters. Click Disconnect to end the GPRS connection session. Remote output OUT1 status control Send an SMS message to the module SIM card number in order to change output OUT1 status. SMS message examples are listed in the table. Notes: Module will change the output status upon receiving SMS message from any phone if table Wireless programming phones is empty. If table is filled in, module output status can be changed using only listed phones Output status may be changed when output OUT1 operation mode is set to Remote control SMS; SMS message must be written in capital letters! SMS message text Description Note OUTPUT 1234 ON Output status changes to ON Enter the Admin or User code instead OUTPUT 1234 OFF Output status changes to OFF of OUTPUT 1234 PULSE=005 Output status changes to ON for a number of seconds indicated refers to a space in the SMS message text. RESET 1234 Restart the module Trikdis 11

13 Annex 1. SMS messages Recorded event CID code Event code sent to CSP SMS text Text in the Contact ID standard SIA DC code table E/R 100 E 100 MEDICAL PANIC ALARM Medical Alarm R 100 E/R 110, 115 E 110 FIRE PANIC ALARM Fire Alarm R 100 E/R 120 E 120 PANIC ALARM Panic Alarm R 120 E 121 E 121 DURESS ALARM Duress Alarm E/R E 130 ALARM Burglary Alarm R130 Alarm restore Burglary Alarm restore E/R 301 E 301 AC Power failure on control panel AC Loss R 301 AC Power failure restored on control panel AC Loss restore E/R 302, 309 E 302 Battery Power failure on control panel Low System battery R 302 Battery Power restored failure on control panel Low system Battery restore E/R 321 E 321 Bell trouble on control panel Bell 1 R 321 Bell trouble restore on control panel Bell 1 restore E/R 351 E 351 Phone Line trouble on control panel Telco 1 fault R 351 Phone Line trouble restored on control panel Telco 1 fault restore E/R 400, 401, E 401 OPEN by Open by user 406, 451 R 401 CLOSE by Close by user E/R 408 E 408 Quick DISARM Quick DISARM R 408 Quick ARM Quick ARM E/R 409 E 409 Key switch zone Key switch zone R 409 Key switch restored Key switch restored E 602 E 602 Periodic Test Periodic test report Trikdis 12

UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage: GSM communicator G10. (v.1.

UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA   Webpage:   GSM communicator G10. (v.1. UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt GSM communicator G10 (v.1.xx) USER MANUAL Description The communicator G10 is designed to transmit

More information

GSM module G10. User manual. (v.1.xx) JSC UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage:

GSM module G10. User manual. (v.1.xx) JSC UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA   Webpage: GSM module G10 (v.1.xx) User manual JSC UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Contents GSM module G10... 3 Operation... 3 Outside view...

More information

GSM module G10 (v.1.3x) User manual. JSC UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage:

GSM module G10 (v.1.3x) User manual. JSC UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA   Webpage: GSM module G10 (v.1.3x) User manual JSC UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Contents GSM module G10... 3 Operation... 3 Outside view...

More information

GSM communicator G09 (v.1.61) User Manual and Installation Guide. Draugystes g. 17, LT Kaunas

GSM communicator G09 (v.1.61) User Manual and Installation Guide. Draugystes g. 17, LT Kaunas GSM communicator G09 (v.1.61) User Manual and Installation Guide Draugystes g. 17, LT-51229 Kaunas E-mail: info@trikdis.lt www.trikdis.lt Purpose of the document This document introduces the features of

More information

GSM module G10T (v.2.3x) Installation manual. TRIKDIS, JSC Draugystės st. 17, LT Kaunas Lithuania

GSM module G10T (v.2.3x) Installation manual. TRIKDIS, JSC Draugystės st. 17, LT Kaunas Lithuania GSM module G10T (v.2.3x) Installation manual TRIKDIS, JSC Draugystės st. 17, LT-51229 Kaunas Lithuania E-mail: info@trikdis.lt www.trikdis.lt Table of Contents GSM module G10T... 3 Operating... 3 Outside

More information

GSM communicator G16 USER MANUAL

GSM communicator G16 USER MANUAL USER MANUAL UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Contents SAFETY REQUIREMENTS... 2 DESCRIPTION... 3 LIST OF COMPATIBLE CONTROL PANELS...

More information

Ethernet communicator E10v2 USER MANUAL. UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage:

Ethernet communicator E10v2 USER MANUAL. UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA   Webpage: USER MANUAL UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Description Ethernet communicator E10 is designed to transmit messages from security

More information

GSM communicator FireCom (v.1.61) User Manual and Installation Guide. Draugystes g. 17, LT Kaunas

GSM communicator FireCom (v.1.61) User Manual and Installation Guide. Draugystes g. 17, LT Kaunas GSM communicator FireCom (v.1.61) User Manual and Installation Guide Draugystes g. 17, LT-51229 Kaunas E-mail: info@trikdis.lt www.trikdis.lt Purpose of the document This document introduces the features

More information

Ethernet communicator E14 USER MANUAL July, 2018

Ethernet communicator E14 USER MANUAL July, 2018 USER MANUAL July, 2018 www.trikdis.lt UAB Trikdis Draugystės g. 17, LT-51229 Kaunas, Lietuva +370 37 408 040 info@trikdis.lt Contents SAFETY REQUIREMENTS... 3 1 DESCRIPTION... 4 1.1 List of Compatible

More information

GSM communicator G16 USER MANUAL

GSM communicator G16 USER MANUAL USER MANUAL UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Contents SAFETY REQUIREMENTS...2 DESCRIPTION...3 LIST OF COMPATIBLE CONTROL PANELS...3

More information

GSM communicator G17F INSTALLATION MANUAL

GSM communicator G17F INSTALLATION MANUAL INSTALLATION MANUAL UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Contents SAFETY REQUIREMENTS...3 DESCRIPTION...4 SPECIFICATIONS...4 COMMUNICATOR

More information

UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage: GSM communicator G16T USER MANUAL

UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA   Webpage:  GSM communicator G16T USER MANUAL UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt GSM communicator G16T USER MANUAL Contents SAFETY REQUIREMENTS... 2 1 DESCRIPTION... 3 SPECIFICATIONS...

More information

UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA Webpage: io expander Installation manual

UAB TRIKDIS Draugystės str. 17, LT Kaunas LITHUANIA   Webpage:   io expander Installation manual UAB TRIKDIS Draugystės str. 17, LT-51229 Kaunas LITHUANIA E-mail: info@trikdis.lt Webpage: www.trikdis.lt Installation manual Contents SAFETY REQUIREMENTS... 2 1. DESCRIPTION... 3 1.1. TECHNICAL PARAMETERS...

More information

Draugystės g. 17 LT Kaunas

Draugystės g. 17 LT Kaunas Draugystės g. 17 LT-51229 Kaunas E-mail info@trikdis.lt www.trikdis.com This document describes controller GV15, its use, features, operation and setting of operation parameters. is a remote control device

More information

Gate controller GC1000

Gate controller GC1000 Gate controller GC1000 User Manual Orvos Monitooring OÜ E-mail: info@orvos.ee Purpose of the document This document describes GC1000, its usage, features, and operation and how to set operation parameters.

More information

SECURITY MODULE SP131

SECURITY MODULE SP131 SECURITY MODULE SP131 User manual 1 CTENTS SAFETY REQUIREMENTS... 3 DESCRIPTI OF THE SECURITY MODULE SP131... 4 COMPATIBLE MODULES... 6 TECHNICAL PARAMETERS... 7 PACKAGE CTENT... 7 MODULE COMPENTS... 8

More information

GSM Communicator PSTN SIA DC-05 Protocol to SIA DC-09 Protocol & SMS Alert

GSM Communicator PSTN SIA DC-05 Protocol to SIA DC-09 Protocol & SMS Alert PSTN Alert To Wireless Alert! Compatible With Most Of The PSTN Security Control Panel. Special Designed For Your Existing PSTN Alarms Systems! PSTN SIA DC-05 Protocol to SIA DC-09 Protocol & SMS Alert

More information

FSK TX CELLULAR PLUS. Installation and Programming Guide. Tel:

FSK TX CELLULAR PLUS. Installation and Programming Guide. Tel: FSK TX CELLULAR PLUS Installation and Programming Guide Tel: 0861 105 962 www.fsk.co.za INTRODUCTION The FSK TX Cellular Plus (TXC+) is a highly featured GSM based unit which is used for the transmission

More information

PCS200 GPRS Communicator Module V1.0

PCS200 GPRS Communicator Module V1.0 PCS200 GPRS Communicator Module V1.0 Installation and User Manual Warranty For complete warranty information on this product please refer to the Limited Warranty Statement found on the website www.paradox.com/

More information

GSM SECURITY AND CONTROL SYSTEM ESIM021

GSM SECURITY AND CONTROL SYSTEM ESIM021 GSM SECURITY AND CONTROL SYSTEM ESIM021 Manual v1.1 Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around: Alarm and control system

More information

A1000 GSM ALARM DEVICE

A1000 GSM ALARM DEVICE A1000 GSM ALARM DEVICE USER MANUAL A1000-REV2.1-1604 FW-A1000v2.93 ERBAŞ TEKNOLOJİ Innovative Solutions 1 www.erbasteknoloji.com SAFETY INSTRUCTIONS - This user manual contains important notices for installation,

More information

A1400 GSM Temperature Alarm USER MANUAL A1400-REV FW-A1400v2.94. ERBAŞ TEKNOLOJİ Innovative Solutions. 1

A1400 GSM Temperature Alarm USER MANUAL A1400-REV FW-A1400v2.94. ERBAŞ TEKNOLOJİ Innovative Solutions. 1 A1400 GSM Temperature Alarm USER MANUAL A1400-REV2.1-1604 FW-A1400v2.94 ERBAŞ TEKNOLOJİ Innovative Solutions 1 www.erbasteknoloji.com SAFETY INSTRUCTIONS - This user manual contains important notices for

More information

PCS200 Communicator Module V2.2

PCS200 Communicator Module V2.2 PCS200 Communicator Module V2.2 Reference and Installation Manual Warranty For complete warranty information, please visit www.paradox.com/terms. Your use of the Paradox product signifies your acceptance

More information

ModemUSB/E12 User Manual v0.1

ModemUSB/E12 User Manual v0.1 User Manual v0.1 TABLE OF CONTENTS TABLE OF CONTENTS...2 1. ATTENTION...3 2. FOR YOUR SAFETY...3 3. USER S SERVICE...5 4. BASIC INFORMATION...6 4.1 Introduction...6 4.2 Legal Notice...6 4.3 Contacts...6

More information

TM50 Touch Intuitive Touchscreen

TM50 Touch Intuitive Touchscreen TM50 Touch Intuitive Touchscreen Description With its bright color display, intuitive icons, and menu-driven interface, the TM50 Touch Intuitive Touchscreen reflects Paradox s commitment to user-centric

More information

EC-11 Ethernet Converter

EC-11 Ethernet Converter EC-11 Ethernet Converter PSTN Contact ID to TCP Converter Installation and Operations Manual Version 8.H3.MID 1 Table of Contents About EC-11 Ethernet Converter... 3 Circuit Board Layout and Wiring Diagram...

More information

GPRS-T1. Monitoring Converter. SATEL sp. z o.o. ul. Schuberta Gdańsk POLAND tel

GPRS-T1. Monitoring Converter. SATEL sp. z o.o. ul. Schuberta Gdańsk POLAND tel Monitoring Converter GPRS-T1 Program version 1.01 gprs-t1_en 04/09 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.pl WARNINGS The module should only

More information

Telephone and Reporting Setup in ElkRP

Telephone and Reporting Setup in ElkRP Telephone and Reporting Setup in ElkRP 1. To add a telephone, right click on Telephones under Folder items on the left side of the screen. Then select New Telephone. 2. On the New Telephone IDs screen,

More information

GPRS Pager 3 INSTALATION AND USER MANUAL

GPRS Pager 3 INSTALATION AND USER MANUAL GPRS Pager 3 INSTALATION AND USER MANUAL 1 Table of contents 1 Main functions of the GPRS Pager3...3 2 Operating mode, installation...3 2.1 Installation if no local network is available...3 2.2 Instalation

More information

EVOHD. Programming Guide. Version

EVOHD. Programming Guide. Version EVOHD Programming Guide Version 1.11 www.paradox.com Warranty For complete warranty information on this product please refer to the Limited Warranty Statement found on our Web site: www.paradox.com. Your

More information

ProLine GSM. Installation manual

ProLine GSM. Installation manual Installation manual ContentS Description of device functions... page 3. Line simulkator function... page 3. Description of the terminal block... page 4. Installation instructions... page 4. LED signals...

More information

Alarm button Contact GSM-1M

Alarm button Contact GSM-1M Alarm button Contact GSM-1M Data sheet Device identification number 2 1. General Information Alarm button Contact GSM-1М (hereinafter referred to as the device) is designed for alarm event generating on

More information

SECURITY MODULE CG3 User Manual

SECURITY MODULE CG3 User Manual SECURITY MODULE CG3 User Manual Security system can be managed with Paradox K636, K10 LED, K32 LED and Protegus SK130 LED Control by the keypad Paradox 1. Full arming the security system (when the security

More information

GPRS-T4. GPRS/SMS Reporting Module. SATEL sp. z o.o. ul. Schuberta Gdańsk POLAND tel

GPRS-T4. GPRS/SMS Reporting Module. SATEL sp. z o.o. ul. Schuberta Gdańsk POLAND tel GPRS/SMS Reporting Module GPRS-T4 Program version 3.01 gprs-t4_en 10/13 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.eu WARNINGS The module should

More information

GC 055. GSM Remote Monitoring. Operating and installation instructions

GC 055. GSM Remote Monitoring. Operating and installation instructions GSM Remote Monitoring Operating and installation instructions GC 055 GSM, GPRS Programmable Communicator Transmits input conditions/controls outputs Measures analogue data Access control system/dallas

More information

GPRS ADAPTER INSTALLATION AND USER MANUAL. for module version v2.24 and higher

GPRS ADAPTER INSTALLATION AND USER MANUAL. for module version v2.24 and higher GPRS ADAPTER INSTALLATION AND USER MANUAL for module version v2.24 and higher Table of contents 1 Main function of the Adapter...3 2 System operation...3 2.1 Transmission through GPRS...4 2.1.1 Router

More information

2 IDS LCD Keypad User Manual C Issued March 2009

2 IDS LCD Keypad User Manual C Issued March 2009 2 3 4 Contents 1. Introduction to the IDS LCD Digital Keypad...8 2. Arming the Control Panel...8 2.1 Away Arming...8 2.1.1 How to Away Arm...8 2.1.2 Quick Away Arm Shortcut Key...8 2.2 Stay Arming...9

More information

Quick Start Installation Guide

Quick Start Installation Guide Quick Start Installation Guide Table of Contents 1. Introduction... 3 2. System Installation... 3 3. System Programming... 5 3.1. Keys Menu Navigation... 5 3.2. Enter Engineer Programming mode... 5 3.3.

More information

TELTONIKA ModemUSB/G10 User Manual v0.1

TELTONIKA ModemUSB/G10 User Manual v0.1 Address: Žirmūnų g. 27, Vilnius LT-09105, Tel.: +370 5 2127472, Fax: +3705 276 1380, E-mail: info@teltonika.lt TELTONIKA User Manual v0.1 TABLE OF CONTENTS TABLE OF CONTENTS... 2 1. ATTENTION... 3 2. FOR

More information

TELTONIKA EDGE camera (MVC100) User s Manual 1.01

TELTONIKA EDGE camera (MVC100) User s Manual 1.01 TELTONIKA EDGE camera (MVC100) User s Manual 1.01 LEGAL NOICE Copyright 2008 TELTONIKA Ltd. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document

More information

Keypad LCD (software version 3.10) CA-10 plus

Keypad LCD (software version 3.10) CA-10 plus PROGRAMMING AND INSTALLATION MANUAL Keypad LCD (software version 3.10) CA-10 plus GDAŃSK ca10plci_e 09/03 WARNING Due to safety reasons, alarm system should be installed by qualified personnel only. Because

More information

MRD-310 MRD G Cellular Modem / Router Web configuration reference guide. Web configuration reference guide

MRD-310 MRD G Cellular Modem / Router Web configuration reference guide. Web configuration reference guide Web configuration reference guide 6623-3201 MRD-310 MRD-330 Westermo Teleindustri AB 2008 3G Cellular Modem / Router Web configuration reference guide www.westermo.com Table of Contents 1 Basic Configuration...

More information

GSM HOME SECURITY SYSTEM

GSM HOME SECURITY SYSTEM Cell /Mobile phone home security system GSM HOME SECURITY SYSTEM Model : BS120 TABLE OF CONTENTS 1. FEATURES... 1 2. APPLICATION... 2 3. SPECIFICATIONS... 3 4. FRONT PANEL & LAYOUT DESCRIPTION...6 5. BASIC

More information

PROGRAMMING HELP GUIDE

PROGRAMMING HELP GUIDE DIGIPLEX EVO48-192 PROGRAMMING HELP GUIDE Entering Programming Mode 1) Press and hold the [0] key 2) Enter your [Installer Code] (default-000000) 3) Enter 4-digit [section] you wish to program 4) Enter

More information

Wireless Expansion Module V2.0 OMN-RCV3. Reference & Installation Manual. Stand-Alone System

Wireless Expansion Module V2.0 OMN-RCV3. Reference & Installation Manual. Stand-Alone System Wireless Expansion Module V2.0 OMN-RCV3 Reference & Installation Manual Stand-Alone System Table of Contents Introduction...3 What s New with Version 2.0... 3 Technical Specifications... 3 System Features...

More information

High Security and Access System EVO48 V2.1 EVO192 V2.1

High Security and Access System EVO48 V2.1 EVO192 V2.1 High Security and Access System EVO48 V2.1 EVO192 V2.1 Programming Guide Includes LCD Keypad Programming We hope this product performs to your complete satisfaction. Should you have any questions or comments,

More information

I/O ETHERNET CONTROLLER ELAN1

I/O ETHERNET CONTROLLER ELAN1 I/O ETHERNET CONTROLLER ELAN1 Manual v1.0 Safety instructions Please read and follow these safety guidelines in order to maintain safety of operators and people around: Don t use the system in hazardous

More information

GPRS/SMS Reporting Module GPRS-T2

GPRS/SMS Reporting Module GPRS-T2 GPRS/SMS Reporting Module GPRS-T2 Program version 2.01 gprs-t2_en 11/11 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.eu WARNINGS The module should

More information

INT-GSM. GPRS communication module. Firmware version 1.00 int-gsm_en 07/18

INT-GSM. GPRS communication module. Firmware version 1.00 int-gsm_en 07/18 INT-GSM GPRS communication module Firmware version 1.00 int-gsm_en 07/18 SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk POLAND tel. +48 58 320 94 00 www.satel.eu IMPORTANT The module should be installed

More information

THANK YOU FOR VOTING TEXECOM INSTALLATION MANUAL. Digi-modems. Issue 3

THANK YOU FOR VOTING TEXECOM INSTALLATION MANUAL. Digi-modems. Issue 3 THANK YOU FOR VOTING TEXECOM INSTALLATION MANUAL Digi-modems Issue 3 Contents Com300 & Com2400 Installation Manual Contents 1. Regulatory Requirements... 3 General...3 Approval... 3 REN Rating... 3 2.

More information

The device works in conjunction with standard alarm systems and is designed for the transmission of alarm messages by GSM network.

The device works in conjunction with standard alarm systems and is designed for the transmission of alarm messages by GSM network. GsmAlarm-330 The device works in conjunction with standard alarm systems and is designed for the transmission of alarm messages by GSM network. FEATURES Transmission of alarm messages to a central monitoring

More information

Voice Fax. User Manual

Voice Fax. User Manual Copyright 2007 UAB Teltonika. All rights reserved. Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of UAB

More information

GPRS-T6. GPRS/SMS Reporting Module with Power Supply

GPRS-T6. GPRS/SMS Reporting Module with Power Supply GPRS/SMS Reporting Module with Power Supply GPRS-T6 Program version 3.01 gprs-t6_en 10/13 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.eu WARNINGS

More information

MultiModem rcell. Intelligent Wireless Router. Quick Start Guide

MultiModem rcell. Intelligent Wireless Router. Quick Start Guide MultiModem rcell Intelligent Wireless Router Quick Start Guide Copyright and Technical Support Quick Start Guide MultiModem rcell MTCBA-Xx-EN2 82100400L, Revision A Copyright 2009 by Multi-Tech Systems,

More information

Modules Programming Guide. paradox.com

Modules Programming Guide. paradox.com Keypad Modules Annunciator Module Motion Detector Modules Zone Expansion Modules Access Control Module Voice Assisted Modules Accessory Modules Integration Module Internet Module Modules Programming Guide

More information

PCS250G GPRS Communicator Module V1.3. The Vital Link. Reference and Installation Manual. Printed in Canada - 08/2013 PCS250G-EI01

PCS250G GPRS Communicator Module V1.3. The Vital Link. Reference and Installation Manual. Printed in Canada - 08/2013 PCS250G-EI01 PCS250G GPRS Communicator Module V1.3 The Vital Link Reference and Installation Manual PARADOX.COM Printed in Canada - 08/2013 PCS250G-EI01 Table of Contents Introduction... 4 Features... 4 Overview...

More information

Ethernet communication module ETHM-1 Plus

Ethernet communication module ETHM-1 Plus Ethernet communication module ETHM-1 Plus Firmware version 2.05 ethm1_plus_en 07/18 SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk POLAND tel. + 48 58 320 94 00 www.satel.eu IMPORTANT The module should

More information

Conversion of Contact ID event codes sent by alarm control panel via GSM and PSTN channel to SMS messages

Conversion of Contact ID event codes sent by alarm control panel via GSM and PSTN channel to SMS messages GSM ProCom Description GSM and PSTN communication Management of 2 independent SIM cards Reception of incoming calls, possibility for restriction Installable behind PBX Management of different prefix numbers

More information

GSM-X. Communication module. Quick installation guide. Full manual is available on Firmware version 1.02 gsm-x_sii_en 08/18

GSM-X. Communication module. Quick installation guide. Full manual is available on   Firmware version 1.02 gsm-x_sii_en 08/18 GSM-X Communication module Quick installation guide Full manual is available on www.satel.eu Firmware version 1.02 gsm-x_sii_en 08/18 SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk Poland tel. +48 58

More information

VBIP-G. Mobile Communicators. Installer Manual VBIP-G, VBIP-3G. Rev

VBIP-G. Mobile Communicators. Installer Manual VBIP-G, VBIP-3G. Rev VBIP-G Mobile Communicators VBIP-G, VBIP-3G Installer Manual Rev. 2016.05.18. DECLARATION OF CONFORMITY (in accordance with 93/68/EEC) We, VILLBAU Security Systems Ltd. (1182 Budapest, Üllői út 611.,

More information

GSM communicator GD-06 Allegro Complete manual

GSM communicator GD-06 Allegro Complete manual GSM communicator GD-06 Allegro Complete manual The GD-06 ALLEGRO is a universal GSM dialer and controller. It can be used for both home and industrial automation purposes, for security applications or

More information

PROGRAMMING AND INSTALLATION MANUAL

PROGRAMMING AND INSTALLATION MANUAL PROGRAMMING AND INSTALLATION MANUAL Keypad LCD-S (software version 3.10) CA-10 plus GDAŃSK ca10plci_s_e 09/03 WARNING Due to safety reasons, alarm system should be installed by qualified personnel only.

More information

GD-02-DIN Universal GSM communicator and controller

GD-02-DIN Universal GSM communicator and controller The GD-02-DIN Universal GSM communicator and controller remotely controls and monitors the status of various appliances. Controlling can be performed using standard SMSes or by dialling in. The device

More information

Quadri-channel receiver RD10 (v.1.01_101215)

Quadri-channel receiver RD10 (v.1.01_101215) (v.1.01_101215) User manual TRIKDIS, JSC Draugystes St. 17, LT-51229 Kaunas, Lithuania Phone: +370 37 408040 Fax: + 370 37 760554 E-mail.: info@trikdis.lt Web: www.trikdis.lt Table of Contents 1 Introduction...

More information

RADIO REMOTE CONTROLLER SET RE-4K

RADIO REMOTE CONTROLLER SET RE-4K RADIO REMOTE CONTROLLER SET RE-4K re4k_en 09/11 The RE-4K four-channel radio remote controller set enables electrical equipment to be remotely controlled by means of radio transmitters (remote keyfobs).

More information

CCTR-820 Mini Water-proof GPS Tracker Using Guide

CCTR-820 Mini Water-proof GPS Tracker Using Guide CCTR-820 Mini Water-proof GPS Tracker Using Guide Welcome to use this Real Time mini water-proof GPS tracker CCTR-820, This product is with GPS module and GSM module, It is specially design for motor,

More information

User Manual Revision 1.02

User Manual Revision 1.02 User Manual Revision 1.02 Manufactured by Contents 1. Introduction... 4 2. Disclaimer and Warranty... 4 3. Specifications... 5 4. Features... 5 5. Quick Start Guide... 6 5.1 Hardware... 6 5.2 Software...

More information

EasyCon GSM. Installation manual

EasyCon GSM. Installation manual Installation manual Contents Description of device functions... page 3. Description of the terminal block... page 3. Installation instructions... page 3. LED signals... page 3. Reset (factory default)...

More information

MG/SP Series (V4.9/V5.1) What s New

MG/SP Series (V4.9/V5.1) What s New MG/SP Series (V4.9/V5.1) What s New Firmware: SP4000 and SP5 version 5.1 SP5500, SP000, SP7000, and MG5050 version 4.9 (SP5500 pictured) Overview: New Programming Sections New Events New Trouble Display

More information

GPRS/GSM IP Communicator Conettix ITS-DX4020-G. Installation and Operation Guide

GPRS/GSM IP Communicator Conettix ITS-DX4020-G. Installation and Operation Guide GPRS/GSM IP Communicator Conettix ITS-D4020-G en Installation and Operation Guide GPRS/GSM IP Communicator Table of Contents en 3 Table of Contents 1 Introduction 5 1.1 Trademarks 5 1.2 Technical Specifications

More information

DIN-RAIL EXPANDER int-iors_en 10/14

DIN-RAIL EXPANDER int-iors_en 10/14 INT-IORS INT-ORS DIN-RAIL EXPANDER int-iors_en 10/14 The INT-IORS expander enables the system to be expanded by 8 programmable wired zones and 8 programmable wired outputs. The INT-ORS expander enables

More information

CA-A480-A Elevator Controller. Reference & Installation Manual

CA-A480-A Elevator Controller. Reference & Installation Manual CA-A480-A Elevator Controller Reference & Installation Manual TABLE OF CONTENTS INTRODUCTION.................................................................. 4 Introduction.............................................................................................

More information

CT-Interface & IRIS Touch 600 Range Installation Manual

CT-Interface & IRIS Touch 600 Range Installation Manual CT-Interface & IRIS Touch 600 Range Installation Manual Coopers I-ON Panel Range Version 2.0 Table of Contents 1 System Overview... 3 2 IRIS Touch 640 PCB Layout... 3 3 Connections for Coopers I-ON Panel

More information

ELC2212X user manual

ELC2212X user manual user manual 1 Safety: Please, keep safety precautions as follows: Do not use our device nearby the medical aparatures. Do not use our device nearby explosive atmosphere. Do not put to high moisture, chemicals

More information

ETHM-2. Ethernet Module. SATEL sp. z o.o. ul. Schuberta Gdańsk POLAND tel

ETHM-2. Ethernet Module. SATEL sp. z o.o. ul. Schuberta Gdańsk POLAND tel Ethernet Module ETHM-2 Firmware version 1.0 ethm2_en 09/08 SATEL sp. z o.o. ul. Schuberta 79 80-172 Gdańsk POLAND tel. + 48 58 320 94 00 info@satel.pl www.satel.pl SATEL's goal is to continually improve

More information

Wireless keypad PRF-LCD-WRL

Wireless keypad PRF-LCD-WRL 1471 prf-lcd-wrl_en 02/17 Wireless keypad PRF-LCD-WRL SATEL sp. z o.o. ul. Budowlanych 66 80-298 Gdańsk POLAND tel. +48 58 320 94 00 www.satel.eu Firmware version 1.00 WARNINGS The device should be installed

More information

QUADIMODO. Quad-Band IP68 GSM MODEM. Quad Band for Worldwide Use. IP68 Enclosure Submersible. Voice / Fax / SMS and Data. GPRS Class B Class 10:

QUADIMODO. Quad-Band IP68 GSM MODEM. Quad Band for Worldwide Use. IP68 Enclosure Submersible. Voice / Fax / SMS and Data. GPRS Class B Class 10: Quad-Band IP68 GSM MODEM Quad Band for Worldwide Use IP68 Enclosure Submersible Voice / Fax / SMS and Data GPRS Class B Class 10: Bundled 3V SIM Card included Internal Antenna (Optional External) RS232

More information

Control Panel Solution 2000 / 3000

Control Panel Solution 2000 / 3000 Control Panel Solution 2000 / 3000 en Quick Reference Guide Control Panel Table of contents en 3 Table of contents 1 Introduction 6 2 Programming 7 2.1 Alphanumeric Codepad Menu Programming 7 2.2 ICON

More information

Table of Contents. HILLS COMNAV INSTALLATION MANUAL V1.3

Table of Contents. HILLS COMNAV INSTALLATION MANUAL V1.3 Table of Contents Introduction... 3 Feature & Benefits... 4 1. Phone Line connection... 4 2. Phone Line connection, and network connection...5 3. Phone Line connection, network connection and integrated

More information

XT30/XT50 PROGRAMMING PART 1. Slide 1. Slide 2. Slide 3. Objectives. XT30/XT50 Basic Training Programming- Part 1. Accessing the Programmer

XT30/XT50 PROGRAMMING PART 1. Slide 1. Slide 2. Slide 3. Objectives. XT30/XT50 Basic Training Programming- Part 1. Accessing the Programmer Slide 1 XT30/XT50 Basic Training Programming- Part 1 Slide 2 Objectives After completing this course you will: 1) Understand how to prepare the panel for programming and how to access the built-in programmer.

More information

CCTR-829 GPS Tracker Using Guide

CCTR-829 GPS Tracker Using Guide CCTR-829 GPS Tracker Using Guide Welcome to use this Real Time GPS tracker CCTR-829 with external microphone & SOS button & ACC detect and control uploading location, this product is with GPS module and

More information

Keypad LCD-L (software version 3.10) CA-10 plus

Keypad LCD-L (software version 3.10) CA-10 plus PROGRAMMING AND INSTALLATION MANUAL Keypad LCD-L (software version 3.10) CA-10 plus GDAŃSK ca10plci_l_e 09/03 WARNING Due to safety reasons, alarm system should be installed by qualified personnel only.

More information

CP150B Vandal & Weather Resistant Keypad Security Systems

CP150B Vandal & Weather Resistant Keypad Security Systems Vandal & Weather Resistant Keypad Security Systems EN Security System CP150B - Vandal & Weather Resistant Keypad The CP150B keypad provides alarm and or access control functionality when used on selected

More information

SF200. Installation Guide & Quick Start Guide. 2 TFT AC Terminal Version: 1.0 Date: June 2014

SF200. Installation Guide & Quick Start Guide. 2 TFT AC Terminal Version: 1.0 Date: June 2014 SF200 Installation Guide & Quick Start Guide 2 TFT AC Terminal Version: 1.0 Date: June 2014 All design and specification declared are subject to change without notice in advance. Contents Safety Precautions

More information

SOFTWARE VERSION 3.20

SOFTWARE VERSION 3.20 48EPEP-00 SOFTWARE VERSION 3.20 HEXA PROGRAMMING: Addresses 000 to 043 and 300 to 527 are programmed using the Hexa Programming method. In this mode, you can enter any hexa-digit from 0-F where keys [1]

More information

irz MC55iT GPRS class 10 GSM modem USER MANUAL

irz MC55iT GPRS class 10 GSM modem USER MANUAL irz MC55iT GPRS class 10 GSM modem USER MANUAL Contents 1. Safety Requirements... 3 2. General Information...4 2.1. Purpose of the Device...4 3.1. Configuration...4 3.2. Parameters...4 3.3. Exterior Appearance...6

More information

Series. NX-8-EUR Control Panel. Installation manual

Series. NX-8-EUR Control Panel. Installation manual g GE Security NetworX TM Series NX-8-EUR Control Panel Installation manual NX-8-EUR Installation manual Page 2 23/12/04 CONTENTS CONTENTS...3 GENERAL INFORMATION...5 ORDERING INFORMATION...5 FEATURE DEFINITIONS...6

More information

Quick Start Guide. The Automotive Internet Experience

Quick Start Guide. The Automotive Internet Experience Quick Start Guide The Automotive Internet Experience Table of Contents System Requirements Package Contents Overview Wi2U router Vehicle Installation Start-up Display Settings Regulatory Information Technical

More information

GETTING TO KNOW YOUR TELSTRA PRE-PAID 4GX WI-FI PLUS

GETTING TO KNOW YOUR TELSTRA PRE-PAID 4GX WI-FI PLUS telstra.com/ppmbb 125 8880 or from a non-telstra phone 13 2200 and say pre-paid visit a telstra store or partner GETTING TO KNOW YOUR TELSTRA PRE-PAID 4GX WI-FI PLUS LET S GET THIS SHOW ON THE ROAD WHAT

More information

Modules Programming Guide

Modules Programming Guide Modules Programming Guide Programming Methods The modules can be programmed using the following methods: 1) Through the WinLoad Security Management Software. The modules can be programmed at 19,200 baud

More information

GM-900 GSM/GPRS modem. Application manual

GM-900 GSM/GPRS modem. Application manual GM-900 GSM/GPRS modem Application manual for module version S900 B09 and higher Rev. 1.0 06.04.2012 Features: USB interface GSM data transfer GPRS data transfer BELL 103/v.21 communication Applications:

More information

telstra.com/ppmbb or from a non-telstra phone and say pre-paid visit a telstra store or partner

telstra.com/ppmbb or from a non-telstra phone and say pre-paid visit a telstra store or partner telstra.com/ppmbb 125 8880 or from a non-telstra phone 13 2200 and say pre-paid visit a telstra store or partner GETTING TO KNOW YOUR TELSTRA PRE-PAID 4G USB+WI-FI PLUS LET S GET THIS SHOW ON THE ROAD

More information

Avantis AXI WEB SERVER MODULE USER MANUAL

Avantis AXI WEB SERVER MODULE USER MANUAL Avantis AXI WEB SERVER MODULE USER MANUAL CONTENTS CHAPTER 1: SYSTEM LOGIN AND WEB PAGE LAYOUT 1.0 ACCESSING THE WEB PAGE 1.1 USER AUTHORITY 1.1.1 MASTER USER 1.1.2 USER/ GUEST SETTING 1.1.3 INSTALLER

More information

UP100-GSM. GSM based intercom and access control. Installation and user manual

UP100-GSM. GSM based intercom and access control. Installation and user manual UP100-GSM GSM based intercom and access control Installation and user manual UP100-GSM REV.1.4 20/01/2014 Table of contents 1 Functions...3 2 Features...3 3 Application area...3 4 Operation...3 4.1 Visitor

More information

NX21 USER MANUAL. Telemetry Unit. Version 1.5

NX21 USER MANUAL. Telemetry Unit. Version 1.5 USER MANUAL Version 1.5 Nortech Management Ltd, United Kingdom NOV 2016 www.nortechonline.co.uk Doc Ref D_000344 Publication Notice Copyright Nortech Management Limited (NML). All rights reserved. No part

More information

2-Way Wireless I/O Expander Installation Guide

2-Way Wireless I/O Expander Installation Guide 2-Way Wireless I/O Expander Installation Guide For more detailed information please refer to the iconnect Installer Manual provided on our website: www.electronics-line.com Table of Contents 1. Introduction...

More information

VISTA 12a / 48a TECHNICAL TRAINING. The Best in Security plus Everyday Convenience & Control

VISTA 12a / 48a TECHNICAL TRAINING. The Best in Security plus Everyday Convenience & Control VISTA 12a / 48a TECHNICAL TRAINING The Best in Security plus Everyday Convenience & Control Version #.007 7th June 2005 VISTA 12a / 48a Training Guide Index 1. Vista Family Features....... p. 3 2. Wiring

More information

EA-GSM-Interface-GB.odt

EA-GSM-Interface-GB.odt EA-GSM-Interface (1.8/1.82) 4/7/213 EA-GSM-Interface GSM-Gateway +41 ()56 648 4 4 / www.leitronic.ch 1/12 EA-GSM-Interface (1.8/1.82) 4/7/213 Contents 1 Overview... 3 2 Specification... 4 2.1 Connectors...

More information

SOFTWARE VERSION 3.10

SOFTWARE VERSION 3.10 738PEP-03 SOFTWARE VERSION 3.10 HEXA PROGRAMMING: Addresses 000 to 043 and 300 to 527 are programmed using the Hexa Programming method. In this mode, you can enter any hexa-digit from 0-F where keys [1]

More information

900E Vehicle GPS Tracker User Manual

900E Vehicle GPS Tracker User Manual Auto leaders 900E Vehicle GPS Tracker User Manual 2009-10-01 1 Table of Contents 1. Working Directions.....3 2. GPS Tracker Installation...3 2.1. Product Parts List...3 2.2. Precaution before Installation...4

More information